TP-Link Archer T4UH V2 operation manual

Archer T4UH

AC1300 High Gain Wireless Dual Band USB Adapter

REV3.0.0

1910011730

Specifications are subject to change without notice.

TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or

registered trademarks of their respective holders.

No part of the specifications may be reproduced in any form or by any means or used to make

any derivative such as translation, transformation, or adaptation without permission from

http://www.tp-link.com

is a registered trademark of

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

 Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions:

1） This device may not cause harmful interference.

2） This device must accept any interference received, including interference that may cause

undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

Note: The manufacturer is not responsible for any radio or TV interference caused by

unauthorized modifications to this equipment. Such modifications could void the user’s authority

to operate the equipment.

FCC RF Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. End users must follow the specific operating instructions for satisfying RF

exposure compliance. This transmitter must not be co-located or operating in conjunction with

any other antenna or transmitter. This equipment has been SAR-evaluated for use in hand.

SAR measurements are based on a 5mm spacing from the body and that compliance is

achieved at that distance.

This device is restricted in indoor environment only.

CE Mark Warning

RF Exposure Information

This device meets the EU requirements (1999/5/EC Article 3.1a) on the limitation of exposure of

the general public to electromagnetic fields by way of health protection.

This device has been tested and meets the ICNIRP exposure guidelines and the European

Standard EN 62209-2. SAR is measured with this device at a separation of 0.5 cm to the body,

while transmitting at the highest certified output power level in all frequency bands of this device.

Carry this device at least 0.5 cm away from your body to ensure exposure levels remain at or

below the as-tested levels.

Restricted to indoor use.

Canadian Compliance Statement

This device complies with Industry Canada license-exempt RSSs. Operation is subject to the

following two conditions:

1） This device may not cause interference, and

2） This device must accept any interference, including interference that may cause undesired

operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio

exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :

1） l’appareil ne doit pas produire de brouillage;

2） l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, meme si le

brouillage est susceptible d’en compromettre le fonctionnement.

Caution:

1） The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the

potential for harmful interference to co-channel mobile satellite systems;

2） For devices with detachable antenna(s), the maximum antenna gain permitted for devices in

the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still

complies with the e.i.r.p. limit;

3） For devices with detachable antenna(s), the maximum antenna gain permitted for devices in

the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits

specified for point-to-point and non-point-to-point operation as appropriate; and

The high-power

5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or

damage to LE-LAN devices.

radars are allocated as primary users (i.e. priority users) of the bands

DFS (Dyna

5470-5600MHz, and 5650-5725MHz.

mic Frequency Selection) products that operate in the bands 5250- 5350 MHz,

Avertissement:

1） Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour une

utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de

satellites mobiles utilisant les mêmes canaux;

2） Le gain maximal d'antenne permis pour les dispositifs avec antenne(s) amovible(s) utilisant

les bandes 5250-5350 MHz et 5470-5725 MHz doit se conformer à la limitation P.I.R.E.;

3） Le gain maximal d'antenne permis pour les dispositifs avec antenne(s) amovible(s) utilisant

la bande 5725-5850 MHz doit se conformer à la limitation P.I.R.E spécifiée pour l’exploitation

point à point et non point à point, selon le cas.

En outre, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute

puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes

5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des

dommages aux dispositifs LAN-EL.

Les produits utilisant la technique d'atténuation DFS (sélection dynamique des fréquences) sur

les bandes 5250- 5350 MHz, 5470-5600MHz et 5650-5725MHz.

Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance 20cm

between the radiator & your body.

Déclaration d'exposition aux radiations:

Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un

environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20

cm de distance entre la source de rayonnement et votre corps.

Industry Canada Statement

CAN ICES-3 (B)/NMB-3(B)

Korea Warning Statements

당해 무선설비는 운용중 전파혼신 가능성이 있음.

NCC Notice

注意！

依據低功率電波輻射性電機管理辦法

第十二條經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻

加大功率或變更原設計之特性或功能。

率、

第十四條

時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電

信。低功率射頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。

減少電磁波影響，請妥適使用。

低功率射頻電機之使用不得影響飛航安全及干擾合法通行；經發現有干擾現象

於 5.25GHz 至 5.35GHz 區域內操作之無線設備的警告聲明

工作頻率 5.250~5.350GHz 該頻段限於室內使用。

BSMI Notice

安全諮詢及注意事項

 請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。

 清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。

 注意防潮，請勿將水或其他液體潑灑到本產品上。

 插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。

 請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。

 請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。

Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам

нормативних документів та вимогам, що передбачені чинними законодавчими актами

України.

Safety Information

 When product has power button, the power button is one of the way to shut off the product;

when there is no power button, the only way to completely shut off power is to disconnect

the product or the power adapter from the power source.

 Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock

and voiding the limited warranty. If you need service, please contact us.

 Avoid water and wet locations.

For EU/EFTA, this product can be used in the following countries:

FI FR DE GR HU IE IT LV

LT LU MT NL PL RO PT SK

SI ES SE GB IS LI NO CH

BE BG HR CY CZ DK EE

Explanation of the symbols on the product label

Symbol Explanation

DC voltage

RECYCLING

This product bears the selective sorting symbol for Waste electrical and electronic

equipment (WEEE). This means that this product must be handled pursuant to

European directive 2012/19/EU in order to be recycled or dismantled to minimize

its impact on the environment.

User has the choice to give his product to a competent recycling organization or to

the retailer when he buys a new electrical or electronic equipment.

CONTENTS

Chapter 1 Product Overview ................................................................................. 1

1.1 Introduction ............................................................................................................. 1

1.2 Features .................................................................................................................. 1

1.3 LED Status .............................................................................................................. 1

Chapter 2 Connect to a Computer ........................................................................ 2

Chapter 3 Windows ................................................................................................ 3

3.1 Install Driver and Utility ........................................................................................... 3

3.2 Join a Wireless Network.......................................................................................... 5

3.2.1 TP-LINK Utility............................................................................................ 6

3.2.2 WPS (Wi-Fi Protected Setup)..................................................................... 6

3.2.3 Windows Wireless Utility .......................................................................... 10

3.3 Management ......................................................................................................... 11

3.3.1 Status ....................................................................................................... 11

3.3.2 Profile ....................................................................................................... 11

3.3.3 Advanced ................................................................................................. 14

3.3.4 SoftAP ...................................................................................................... 14

3.3.5 About ........................................................................................................ 15

3.4 Uninstall Driver and Utility ..................................................................................... 16

Chapter 4 Mac OS X ............................................................................................. 17

4.1 Install Driver and Utility ......................................................................................... 17

4.2 Join a Wireless Network........................................................................................ 22

4.2.1 TP-LINK Utility.......................................................................................... 22

4.2.2 WPS (Wi-Fi Protected Setup)................................................................... 24

4.3 Management ......................................................................................................... 28

4.4 Uninstall Driver and Utility ..................................................................................... 30

Chapter 5 Linux .................................................................................................... 32

Appendix A: Specifications................................................................................... 33

Appendix B: Glossary............................................................................................ 34

Archer T4UH AC1300 High Gain Wireless Dual Band USB Adapter User Guide

Chapter 1 Product Overview

1.1 Introduction

The TP-LINK Archer T4UH AC1300 High Gain Wireless Dual Band USB Adapter connects your

notebook or desktop computer over Wi-Fi to an 11ac or other network for applications such as

lag-free video streaming, online gaming, and secure Internet surfing.

1.2 Features

 Supports 802.11ac standard

 Seamlessly compatible with 802.11a/b/g/n/ac products

 USB 3.0 port

 Equipped with a USB Cradle for flexible deployment

 Dual Band connections for lag-free HD video streaming and gaming

 Maximum speed of up to 867Mbps for 5GHz network and up to 400Mbps for 2.4GHz

network

 Supports ad-hoc and infrastructure mode

 Easy wireless security encryption at a push of the WPS button

 Supports 64/128 WEP, WPA/WPA2, WPA-PSK/WPA2-PSK(TKIP/AES), supports IEEE

802.1x

 Easy Wireless Configuration Utility

 Supports Windows XP/7/8/8.1/10 32/64bit, Mac OS X 10.6 - 10.11, Linux

1.3 LED Status

Status Working Status

The driver has not been installed.

Off

The adapter's radio has been disabled.

Flashing Slowly The driver has been installed but no data is being transmitted or received.

Flashing Quickly Data is being transmitted or received.

Archer T4UH AC1300 High Gain Wireless Dual Band USB Adapter User Guide

Chapter 2 Connect to a Computer

Before you begin using your adapter, connect the adapter to your computer.

Option 1: Directly

Insert the adapter into a USB port on your computer directly.

Option 2: Via the USB Cradle

Connect the adapter and your computer with the provided USB cradle.

W P S

Note:

 In Windows XP, a Found New Hardware Wizard window will appear when the adapter is

detected. Please click Cancel.

 The adapter provides the best performance with a USB 3.0 port and is also compatible with

a USB 2.0 or USB 1.1 port.

After connecting your adapter to the computer, please follow the instructions in the appropriate

chapter for your operating system: Windows

, Mac OS X, Linux.

Archer T4UH AC1300 High Gain Wireless Dual Band USB Adapter User Guide

Chapter 3 Windows

3.1 Install Driver and Utility

The Setup Wizard will guide you through the installation procedure. We use the procedures in

Windows 7 as an example - the procedures may vary slightly for other versions of Windows.

1. Insert the resource CD into your CD drive and run the Autorun.exe from the pop-up

AutoPlay window. Select Archer T4UH and click Install Driver and Utility to begin.

Note:

 The CD is included in the package. If your CD does not work or your computer doesn't

support the CD, you can also download the driver and utility from the TP-LINK website

(http://www.tp-link.com

 In some operating systems, the CD screen will pop up automatically. Otherwise, run the CD

manually.

2. The InstallShield Wizard window displays. Click Next to continue.

Archer T4UH AC1300 High Gain Wireless Dual Band USB Adapter User Guide

3. Choose a setup type. It is recommended to select Install TP-LINK Wireless

Configuration Utility and Driver. Click Next.

4. If you want to change install location, click Change to specify the location for the software

installation. Or you can leave it default. Click Next.

5. Click Install. After a few minutes, the installation completes. Click Finish.

6. TP-LINK Utility pops up after installation. Its icon appears on the desktop as and on

Archer T4UH AC1300 High Gain Wireless Dual Band USB Adapter User Guide

the taskbar as adapter. For more information, please refer to Join a Wireless Network

. You can use the TP-LINK Utility to join a Wi-Fi network with your

3.2 Join a Wireless Network

There are three options of using the adapter to join a Wi-Fi network.

Option 1: TP-LINK Utility

TP-LINK Utility lets you easily connect the adapter to a Wi-Fi network and manage the adapter.

Option 2: WPS (Wi-Fi Protected Setup)

WPS (Wi-Fi Protected Setup) is a network security standard for easily adding computers and

other devices to a home network. Use this method if your wireless router or access point

supports WPS.

Option 3: Windows Wireless Utility

You can use the Windows WLAN Autoconfig service (for Windows 7/8/8.1/10) and the Wireless

Zero Configuration service (for Windows XP) to join a Wi-Fi network.

+ 30 hidden pages