Toyota Sienna 2008 Owner's Manual
08 SIENNA_U (L/O 0801)
SECTION 1− 1
OPERATION OF INSTRUMENTS AND
CONTROLS
Overview of instruments and controls
Instrument panel overview 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument cluster overview 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Indicator symbols on the instrument panel 7. . . . . . . . . . . . . . . . . . . . . . .
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
1
Instrument panel overview
08 SIENNA_U (L/O 0801)
1. Side defroster outlets
2. Side vents
3. Instrument cluster
4. Center vents
5. Multi−information display or garage
door opener box
6. Auxiliary boxes
7. Glove box
8. Power window switches
9. Power door lock switches
10. Seat heater dials or auxiliary box
11. Cup holder and coin holder
12. Power outlets
13. Automatic transmission selector lever
14. Tire pressure warning system reset
switch
15. Power sliding door main switch
(“SLIDE DOOR OFF” switch)
16. Parking brake pedal
17. Window lock switch
18. Driving position memory buttons
19. Hood lock release lever
20. Power back door main switch
(“BACK DOOR OFF” switch)
2
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
08 SIENNA_U (L/O 0801)
1. Headlight, turn signal and front fog
light switches
2. Wiper and washer switches
3. Rear window and outside rear view
mirror defogger and windshield wiper
de−icer switch
4. Emergency flasher switch
5. Audio system or rear view monitor
system/navigation system including
audio system (For the navigation
system, see the separate “Navigation
System Owner’s Manual”.)
6. Power outlet main switch
7. AUX adapter
8. Air conditioning controls
9. “AIR BAG ON” and “AIR BAG OFF”
indicator lights
10. Toyota park assist system switch and
indicator light
11. Personal light main switch
12. Engine switch
13. “TRAC OFF” switch
14. Cruise control switch or dynamic laser
cruise control switch
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
3
15. Tilt and telescopic steering lock release
lever
16. Power rear view mirror control switches
17. “REAR VENT” switch
18. Headlight beam level control dial
08 SIENNA_U (L/O 0801)
"Overhead console "Steering switches
1. Conversation mirror
2. Power back door switch
3. Front personal lights
4. Power sliding door switches
5. Electric moon roof switch
6. Microphone
1. Volume control switches for audio
system/hands−free system
2. “ƜƝ” switch
3. “MODE” switch
4. Telephone switches
5. Distance switch
6. Talk switch
4
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
Instrument cluster overview
"Type A
08 SIENNA_U (L/O 0801)
1. Service reminder indicators and
indicator lights
2. Speedometer
3. Engine coolant temperature gauge
4. Low fuel level warning light
5. Fuel gauge
6. Trip meter reset knob/instrument panel
light control knob
7. Odometer and two trip meters
8. Tachometer
5
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
"Type B
08 SIENNA_U (L/O 0801)
1. Service reminder indicators and
indicator lights
2. Speedometer
3. Engine coolant temperature gauge
4. Low fuel level warning light
6
5. Fuel gauge
6. Dynamic laser cruise control master
warning light
7. Dynamic laser cruise control display
8. Trip meter reset knob/instrument panel
light control knob
9. Odometer and two trip meters
10. Tachometer
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
Indicator symbols on the instrument panel
08 SIENNA_U (L/O 0801)
or
Brake system warning light
Driver ’s seat belt reminder light
Front passenger’s seat belt reminder light
Charging system warning light
or Malfunction indicator lamp
Low engine oil pressure warning light
∗
1
∗
1
∗
1
∗
1
or Anti−lock brake system warning light
∗
Open door warning light
SRS warning light
Vehicle stability control system/traction control
system warning light
1
∗
1
∗
1
Low tire pressure warning light
∗
1
Low windshield washer fluid level warning
∗
1
light
∗
1
Engine oil replacement reminder light
∗
1
∗
1
∗
1
(for vehicles sold in U.S.A.)
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
7
Third seat warning light
08 SIENNA_U (L/O 0801)
∗
1
Slip indicator light
Engine immobilizer/theft deterrent system
indicator light
“AIR BAG ON” indicator light
“AIR BAG OFF” indicator light
Headlight indicator light
Tail light indicator light
Headlight high beam indicator light
∗
1
: For details, see “Service reminder indicators and warning
buzzers” on page 191 in Section 1−6.
∗
2
: If this light flashes, see “Cruise control” on page 222 in
Section 1−7.
∗
3
: If this light flashes, see “Dynamic laser cruise control” on
Traction control system off indicator light
(two−wheel drive models)
∗
Cruise control indicator light
cruise control indicator light
2
or dynamic laser
∗
3
Dynamic laser cruise control ready mode
indicator light
Conventional cruise control mode indicator light
page 225 in Section 1−7.
Turn signal indicator lights
Automatic transmission indicator lights
8
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
08 SIENNA_U (L/O 0801)
SECTION 1− 2
OPERATION OF INSTRUMENTS AND
CONTROLS
Keys and Doors
Keys 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine immobilizer system 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wireless remote control 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front doors 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sliding doors 25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power sliding doors 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Back door 36. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power back door 38. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power windows 43. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manual quarter windows 46. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power quarter windows 47. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hood 48. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Theft deterrent system 49. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel tank cap 51. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electric moon roof 53. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
9
08 SIENNA_U (L/O 0801)
Keys (without engine
immobilizer system)
Your vehicle is supplied with two kinds
of keys.
1. Master keys—These keys work in every lock.
2. Sub key—This key will not work in the
glove box.
To protect items locked in the glove box
when using valet parking, leave the sub
key with the attendant.
Since the front doors and sliding doors
can be locked without a key, you should
always carry a spare master key in case
you accidentally lock your keys inside the
vehicle.
KEY NUMBER PLATE
Your key number is shown on the plate.
Keep the plate in a safe place such as
your wallet, not in the vehicle.
If you should lose your keys or if you
need additional keys, duplicates can be
made by a Toyota dealer using the key
number.
We recommend writing down the key number and storing it in a safe place.
Keys (with engine immobilizer
system)
Your vehicle is supplied with two kinds
of keys.
1. Master keys (black)—These keys work
in every lock. Your Toyota dealer will
need one of them to make a new key
with a built−in transponder chip.
2. Sub key (gray)—This key will not work
in the glove box.
A transponder chip for engine immobilizer
system has been placed in the head of
the master and sub keys. These chips are
needed to enable the system to function
correctly, so be careful not to lose these
keys. If you make your own duplicate key,
you will not be able to cancel the system
or start the engine.
10
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
To protect items locked in the glove box
when using valet parking, leave the sub
key with the attendant.
Since the front doors and sliding doors
can be locked without a key, you should
always carry a spare master key in case
you accidentally lock your keys inside the
vehicle.
08 SIENNA_U (L/O 0801)
NOTICE
When using a key containing a transponder chip, observe the following
precautions:
z When starting the engine, do not
use the key with a key ring resting
on the key grip and do not press
the key ring against the key grip.
Otherwise the engine may not start,
or may stop soon after it starts.
z When starting the engine, do not
use the key with other transponder
keys around (including keys of other vehicles) and do not press other
key plates against the key grip.
Otherwise the engine may not start,
or may stop soon after it starts. If
this happens, remove the key once
and then insert it again after removing other transponder keys (including keys of other vehicles) from the
ring or while gripping or covering
them with your hand to start the
engine.
11
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
z Do not bend the key grip.
08 SIENNA_U (L/O 0801)
z Do not cover the key grip with any
material that cuts off electromagnetic waves.
z Do not knock the key hard against
other objects.
z Do not leave the key exposed to
high temperatures for a long period,
such as on the dashboard and hood
under direct sunlight.
z Do not put the key in water or
wash it in an ultrasonic washer.
z Do not use the key with electromag-
netic materials.
KEY NUMBER PLATE
Your key number is shown on the plate.
Keep the plate in a safe place such as
your wallet, not in the vehicle.
If you should lose your keys or if you
need additional keys, duplicates can be
made by a Toyota dealer using the key
number.
We recommend writing down the key number and storing it in a safe place.
12
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
Engine immobilizer system
The engine immobilizer system is a
theft prevention system. When you insert the key in the engine switch, the
transponder chip in the key’s head
transmits an electronic code to the vehicle. The engine will start only when
the electronic code in the chip corresponds to the registered ID code for
the vehicle.
Never leave the keys inside the vehicle
when you leave the vehicle.
08 SIENNA_U (L/O 0801)
The system is automatically set when the
key is removed from the engine switch.
On some models—
The indicator light will start flashing to
show the system is set.
If any of the following indicator conditions
occurs, contact your Toyota dealer.
D The indicator light stays on except
when the theft deterrent system is setting or activating. (See “Theft deterrent
system” on page 49 in this Section.)
D The indicator light does not start flash-
ing when the key is removed from the
engine switch.
D The indicator light flashes inconsistent-
ly.
Inserting the registered key in the engine
switch automatically cancels the system,
which enables the engine to start. The
indicator light will go off.
The system is maintenance−free.
For your Toyota dealer to make you a
new key with built−in transponder chip,
your dealer will need your key number
and master key. However, there is a limit
to the number of additional keys your
Toyota dealer can make for you.
If you make your own duplicate key,
you will not be able to cancel the system or start the engine.
NOTICE
Do not modify, remove or disassemble the engine immobilizer system. If any unauthorized changes or
modifications are made, proper operation of the system cannot be guaranteed.
13
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
For vehicles sold in U.S.A.
08 SIENNA_U (L/O 0801)
Wireless remote control—
For vehicles sold in Canada
FCC ID: MOZ RI−21BTY
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
CAUTION
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
This device complies with RSS−210 of
Industry Canada. Operation is subject to
the following two conditions:
(1) This device may not cause interference, and (2) this device must accept
any interference, including interference
that may cause undesired operation of
the device.
Type A
Type B
14
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
08 SIENNA_U (L/O 0801)
1. Lock switch
2. Unlock switch
3. Alarm switch
4. Sliding door open switch (right side)
5. Back door open switch
6. Sliding door open switch (left side)
The wireless remote control system is
designed to lock or unlock all the side
doors and back door, or activate the
panic mode from a distance within
approximately 1 m (3 ft.) of the vehicle.
On some models, the system also allows you to activate the theft deterrent
system from the same distance.
When you operate any switch, push it
slowly and securely.
The wireless remote control transmitter is
an electronic component. Observe the following instructions in order not to cause
damage to the wireless remote control
transmitter.
D Do not leave the transmitter in places
where the temperature becomes high
such as on the dashboard.
D Do not disassemble it.
D Avoid knocking it hard against other
objects or dropping it.
D Avoid putting it in water.
You can use up to 4 wireless remote control transmitters for the same vehicle.
Contact your Toyota dealer for detailed
information.
If the wireless remote control transmitter
does not actuate the doors or alarm, or
operate from a normal distance:
D Check for closeness to a radio trans-
mitter such as a radio station or an
airport which can interfere with normal
operation of the transmitter.
D The battery may have been consumed.
Check the battery in the transmitter. To
replace the battery, see “—Replacing
battery” on page 20.
If you lose your wireless remote control
transmitter, contact your Toyota dealer as
soon as possible to avoid the possibility
of theft, or an accident. (See “If you lose
your wireless remote control transmitter”
on page 493 in Section 4.)
MADE IN U.S.A.
This complies with Part 15 of the FCC
rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful
interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
15
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
—Locking and unlocking
doors
Locking operation (type A)
Unlocking operation (type A)
08 SIENNA_U (L/O 0801)
Locking operation (type B)
Unlocking operation (type B)
To lock and unlock all the doors, push
the switches of the transmitter slowly
and securely.
To lock: Push the lock switch. All the side
doors and back door are locked simultaneously. At this time one beep will be
heard, turn signal lights will flash once.
Check to see that the doors are securely
locked.
If any of the side doors or back door is
not securely closed, or if the key is in the
engine switch, locking cannot be performed by the lock switch and a beep will
sound continuously for 10 seconds. However, if the key is in the engine switch,
a beep will not sound.
To stop the beep, close all the side doors
and back door securely or push the unlock switch.
The buzzer can be disabled. For details,
contact your Toyota dealer.
To unlock: Push the unlock switch once to
unlock only the driver’s door. Pushing the
switch twice within 3 seconds unlocks all
the side doors and back door simultaneously. Each time the unlock switch is
pushed, two beeps will be heard, turn signal lights will flash twice.
16
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
This double switch operation to unlock all
the side doors and back door can be
changed to a single switch operation. For
details, contact your Toyota dealer.
When the unlock switch is pressed, the
front personal lights and engine switch
light come on. The lights remains on for
about 15 seconds unless any of the side
doors or back door are opened then and
closed. (For further information, see “Front
personal lights” on page 179 and/or “Engine (ignition) switch light” on page 181 in
Section 1−5.)
You have 60 seconds to open a door after
using the wireless remote unlock feature.
If a door is not opened by then, all the
side doors and back door will automatically lock again.
The timing for the automatic door lock
function can be changed. For details, contact your Toyota dealer.
If the lock or unlock switch is kept
pressed in, the locking or unlocking operation is not repeated. Release the switch
and then push again.
08 SIENNA_U (L/O 0801)
—Opening and closing sliding
doors
The following adjustments can be made in
this system. For details, contact your
Toyota dealer.
D Cancelling the wireless door locking or
unlocking function
D Cancelling the flash of the turn signal
lights
D Cancelling the beep sound
Right side power sliding door (type A)
Right side power sliding door (type B)
17
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
08 SIENNA_U (L/O 0801)
Left side power sliding door (type B only)
Push and hold the switch of the wireless remote control transmitter about
one second. The power sliding door
opens and closes completely.
Right side power sliding door—
To open: Push the sliding door open
switch (right side).
To close: Push the sliding door open
switch (right side) again.
Left side power sliding door—
To open: Push the sliding door open
switch (left side).
To close: Push the sliding door open
switch (left side) again.
Opening operation can be performed by
the switches under the following conditions
only:
D The sliding door is unlocked.
D The power sliding door system is on.
(The “SLIDE DOOR OFF” switch on the
instrument panel is pushed out.)
D The key is not in the engine switch.
D The sliding door is between the fully−
closed position and half−opened position.
The sliding door stops at the half−opened
position when the window is opened more
than about 15 cm (6 in.).
The left side power sliding door does not
operate when the fuel filler door is
opened.
Closing operation can be performed by the
wireless remote control switches under the
following conditions only:
D The power sliding door system is on.
(The “SLIDE DOOR OFF” switch on the
instrument panel is pushed out.)
D The key is not in the engine switch.
D The sliding door is between the fully−
opened position and half−opened position.
The sliding door operation by the wireless
remote control can be changed or disabled. For details, contact your Toyota
dealer.
18
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
—Opening and closing back
door (type B only)
Push and hold the back door open
switch on the wireless remote control
transmitter for about one second. The
power back door opens and closes
completely.
When closing or opening the back door,
two beeps will be heard and the turn signal lights will flash twice.
08 SIENNA_U (L/O 0801)
Opening operation can be performed by
the switch under the following conditions
only:
D The back door is unlocked.
D The power back door system is on.
(The “BACK DOOR OFF” switch on the
instrument panel is pushed out.)
D The key is not in the engine switch.
D The back door is between the fully−
closed position and half−opened position.
Closing operation can be performed by the
switch under the following conditions only:
D The power back door system is on.
(The “BACK DOOR OFF” switch on the
instrument panel is pushed out.)
D The key is not in the engine switch.
D The back door is between the fully−
opened position and half−opened position.
The back door operation by the wireless
remote control can be changed or disabled. For details, contact your Toyota
dealer.
—Activating alarm
Pushing and holding the alarm switch
blows the horn intermittently and
flashes the headlights, tail lights and
turns on the front personal lights.
The alarm switch is used to deter vehicle
theft when you witness anyone attempting
to break into or damage your vehicle.
The alarm will last for one minute. To stop
alarm midway, do the following:
D Push any of the switch on the wireless
remote control transmitter.
D Lock or unlock either front doors or
back door with the key.
D Turn the engine switch from the
“LOCK” to “ON” position.
19
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
The alarm does not work when the engine
switch is in the “ON” position.
This alarm function can be disabled. For
details, contact your Toyota dealer.
08 SIENNA_U (L/O 0801)
—Replacing battery
For replacement, use a CR2032 lithium
battery or equivalent.
CAUTION
Special care should be taken to prevent small children from swallowing
the removed transmitter battery or
components.
NOTICE
z When replacing the transmitter bat-
tery, be careful not to lose the components.
z Replace only with the same or
equivalent type recommended by a
Toyota dealer.
z Dispose of used batteries according
to the local laws.
1. Using a coin or equivalent, open the
transmitter case.
20
Replace the transmitter battery by following these procedures:
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
08 SIENNA_U (L/O 0801)
z Be careful not to bend the electrode
when inserting the transmitter battery and that dust or oils do not
adhere to the transmitter case.
z Close the transmitter case securely.
After replacing battery, check that the
transmitter operates properly. If the transmitter still does not operate properly, contact your Toyota dealer.
2. Remove the discharged transmitter battery.
NOTICE
Do not bend the terminals.
3. Put in a new transmitter battery with
positive (+) side up.
Close the transmitter case securely.
NOTICE
z Make sure the positive side and
negative side of the transmitter battery are faced correctly.
z Do not replace the battery with wet
hands. Water may cause unexpected
rust.
z Do not touch or move any compo-
nents inside the transmitter, or it
may interfere with proper operation.
21
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
Front doors—
08 SIENNA_U (L/O 0801)
When either front door is unlocked with a
key, the front personal lights and engine
switch light will come on and remain on
for about 15 seconds before fading out.
(For details, see “Front personal lights” on
page 179 and “Engine (ignition) switch
light” on page 181 in Section 1−5.)
LOCKING AND UNLOCKING WITH KEY
Insert the key into the keyhole and turn
it.
To lock: Turn the key forward.
To unlock: Turn the key backward.
All the side doors and back door lock and
unlock simultaneously with either front
door. In the driver’s door lock, turning the
key once will unlock the driver’s door and
twice in succession will unlock all the
doors simultaneously.
This double key turning operation to unlock all the side doors and back door can
be changed to a single key turning operation. For details, contact your Toyota dealer.
22
LOCKING AND UNLOCKING WITH
INSIDE LOCK KNOB
Move the lock knob.
To lock: Push the knob forward.
To unlock: Pull the knob backward.
The front doors can be opened by pulling
the inside handles even if the lock knobs
are in the locked position.
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
08 SIENNA_U (L/O 0801)
CAUTION
Do not pull the inside handle of the
front doors while driving. The doors
will open and an accident may occur.
Toyota strongly recommends that all
children be placed in the rear seat of
the vehicle.
Closing the door with the lock knob in the
lock position will also lock the door. Be
careful not to lock your keys in the vehicle.
The front doors cannot be locked if you
leave the key in the engine switch.
Driver’s side
LOCKING AND UNLOCKING WITH
POWER DOOR LOCK SWITCH
Push the switch.
To lock: Push the switch down on the
front side.
To unlock: Push the switch down on the
rear side.
Operating the switch simultaneously locks
or unlocks all the side doors and back
door.
If you do either of the following, no side
door or back door can be unlocked with
the power door lock switch.
D Lock all the side doors and back door
with the key or wireless remote control
transmitter when all the side doors and
back door are closed.
D Open the driver’s door or front passen-
ger’s door and move the inside lock
knobs of both front doors to the lock
position, then close the front doors.
Front passenger’s side
23
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
The power door lock switch can be reset
in the following ways.
D Turn the engine switch to “ON”.
D Unlock all the side doors and back
door with the key or wireless remote
control transmitter.
D Unlock the driver’s door or front pas-
senger’s door with the inside lock
knob, and then unlock all the doors
and back door with the power door
lock switch.
CAUTION
Before driving, be sure that the doors
are closed and locked, especially
when small children are in the vehicle. Along with the proper use of
seat belts, locking the doors helps
prevent the driver and passengers
from being thrown out from the vehicle in an accident. It also helps prevent the doors from being opened
unintentionally.
08 SIENNA_U (L/O 0801)
—Automatic door locking and
unlocking functions
AUTOMATIC DOOR LOCKING
You can select the following functions:
D Locking linked with the shift position
All doors are automatically locked when
the selector lever is moved out of “P”
position.
D Locking linked with vehicle speed
All doors are automatically locked when
the vehicle speed goes above about 20
km/h (12 mph).
You can set or cancel the automatic
door locking functions:
Be sure to apply the parking brake when
performing the following operations.
To select the locking linked with the
shift position:
1. Close all doors and turn the engine
switch to the “ON” position.
2. Shift the selector lever to the “P” position.
3. Within 10 seconds of turning the engine switch to the “ON” position, press
and hold the driver’s side power door
lock switch in the lock position for 5
seconds and then release.
The doors will be locked and unlocked
to indicate that the function is set.
To cancel the function, do the above operation again.
To select the locking linked with the
vehicle speed:
1. Close all doors and turn the engine
switch to the “ON” position.
2. Shift the selector lever from “P” to the
“N” position.
3. Within 10 seconds of turning the engine switch to the “ON” position, press
and hold the driver’s side power door
lock switch in the lock position for 5
seconds and then release.
The doors will be locked and unlocked
to indicate that the function is set.
To cancel the function, do the above operation again.
24
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
AUTOMATIC DOOR UNLOCKING
You can select the following functions:
D Unlocking linked with the shift posi-
tion
All doors are automatically unlocked
when the selector lever is moved to
“P” position.
D Unlocking linked with the engine
switch
All doors are automatically unlocked
when the driver’s door is opened within
10 seconds after the engine switch is
turned to the “ACC” or “LOCK” position, or the key is removed.
You can set or cancel the automatic
door unlocking functions:
Be sure to apply the parking brake when
performing the following operations.
To select the unlocking linked with the
shift position:
1. Close all doors and turn the engine
switch to the “ON” position.
2. Shift the selector lever to the “P” position.
08 SIENNA_U (L/O 0801)
3. Within 10 seconds of turning the engine switch to the “ON” position, press
and hold the driver’s side power door
lock switch in the unlock position for
5 seconds and then release.
The doors will be locked and unlocked
to indicate that the function is set.
To cancel the function, do the above operation again.
To select the unlocking linked with the
engine switch:
1. Close all doors and turn the engine
switch to the “ON” position.
2. Shift the selector lever from “P” to the
“N” position.
3. Within 10 seconds of turning the engine switch to the “ON” position, press
and hold the driver’s side power door
lock switch in the unlock position for
5 seconds and then release.
The doors will be locked and unlocked
to indicate that the function is set.
To cancel the function, do the above operation again.
Sliding doors (non−powered)
LOCKING AND UNLOCKING WITH
INSIDE LOCK KNOB
Move the lock knob.
To lock: Move the knob forward.
To unlock: Move the knob backward.
Closing the sliding door with the lock knob
in the lock position will also lock the sliding door. Be careful not to lock your keys
in the vehicle.
25
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
08 SIENNA_U (L/O 0801)
CLOSING THE FULLY−OPENED SLIDING
DOOR
To close the fully−opened sliding door, pull
the inside or outside handle and then
close the door.
CAUTION
Before driving, be sure that the doors
are closed and locked, especially
when small children are in the vehicle. Along with the proper use of
seat belts, locking the doors helps
prevent the passengers from being
thrown out from the vehicle in an
accident. It also helps prevent the
doors from being opened unintentionally.
Sliding door closer (on some models):
When the sliding door has not been fully
closed, it is automatically closed completely even if the power sliding door system is off.
CAUTION
D Careful attention is needed so as
not to get your fingers trapped as
the sliding door automatically
closes when it has not been fully
closed.
D Never allow a child to operate the
sliding door.
NOTICE
Do not apply excessive force when
the sliding door closer is operating.
Otherwise, the sliding door closer
may be damaged.
CAUTION
D When closing the sliding door, con-
firm safety of the area around.
Keep the heads, hands and other
parts of the bodies of all occupants
away from the sliding door. Otherwise, the closing door may cause
death or serious injury.
D When the vehicle is stopped on a
slope, the door will slide faster
when opening or closing, so be especially careful that the passengers
do not get hit or pinched by the
door.
26
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
D When stopping on a downward
slope, open the door fully while
passengers are getting on or off.
Do not pull the outside handle or
inside handle while the door is
open as the door could suddenly
close by itself causing injury.
NOTICE
Do not close the sliding door by applying the brakes. Doing so could
cause the door to be damaged.
08 SIENNA_U (L/O 0801)
When the fuel filler door is opened, the
left side sliding door will not open.
Close the fuel filler door securely and
then operate the sliding door.
NOTICE
Avoid forcibly opening the left side
sliding door fully when the fuel filler
door is opened. Otherwise, the fuel
filler door may be damaged.
When the sliding door window is
opened more than about 15 cm (6 in.),
the sliding door will stop at half−
opened position for safety reasons.
Close the window and then operate the
sliding door.
CAUTION
Do not leave the sliding door at half−
opened position because the door is
not latched at this position. If the
vehicle is stopped on a downward
slope, it may move and cause an unexpected injury.
27
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
SLIDING DOOR CHILD−PROTECTORS
Open the sliding door fully and move
the lock lever to the “LOCK” position
as shown on the label. Then close the
sliding door.
If the child−protector is locked, you cannot
open the sliding door from the inside. We
recommend using this feature whenever
small children are in the vehicle.
08 SIENNA_U (L/O 0801)
Power sliding doors—
On Off
POWER SLIDING DOOR MAIN SWITCH
(“SLIDE DOOR OFF” switch)
This switch is used to turn on and off
the power sliding door system. In order
to operate the power sliding door, the
“SLIDE DOOR OFF” switch on the instrument panel must be pushed out.
(The orange line on top of the switch
indicates that the power sliding door
system is on.) To disable the power
sliding door feature, push in the switch.
When the power sliding door system is
on, you can open and close the sliding
door with the power sliding door switches
on the overhead console or wireless remote control transmitter even if the sliding
door child−protector is locked.
When the power sliding door system is
off, you can open and close the sliding
door by the same operations as non−pow-
ered sliding door.
The sliding door closer is operative even
if the power sliding door system is off.
See page 32 about sliding door closer.
CAUTION
D Do not leave small children or pets
unattended in your vehicle. They
could operate the power sliding
door and injure themselves or others. Turn off the power sliding door
system when the power sliding door
is not in use.
D When jacking up the vehicle, turn
off the power sliding door system
and close the sliding door completely.
28
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
08 SIENNA_U (L/O 0801)
NOTICE
When your vehicle goes through an
automatic car wash, make sure the
power sliding door system is off.
CAUTION
Before driving, be sure that the doors
are closed and locked, especially
when small children are in the vehicle. Along with the proper use of
seat belts, locking the doors helps
prevent the passengers from being
thrown out from the vehicle in an
accident. It also helps prevent the
doors from being opened unintentionally.
LOCKING AND UNLOCKING WITH
INSIDE LOCK KNOB
Move the lock knob.
To lock: Move the knob forward.
To unlock: Move the knob backward.
Closing the sliding door with the lock knob
in the lock position will also lock the sliding door. Be careful not to lock your keys
in the vehicle.
29
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
—Operation of power sliding
door
The power sliding door can be operated
automatically in the following ways:
D Operates with the power sliding door
switches inside the vehicle
D Operates with the wireless remote con-
trol transmitter
D Assists operation with the outside or
inside handle by hand
The power sliding door system can be
canceled by the “SLIDE DOOR OFF”
switch.
When the power sliding door system is
on, if you put the transmission out of “P”
with the engine switch in the “ON” position and the sliding door is not completely
closed, a buzzer will sound.
CAUTION
08 SIENNA_U (L/O 0801)
NOTICE
Do not apply excessive force when
the sliding door is operated automatically. Otherwise, the power sliding
door system may be damaged.
You can cause a beep to sound when the
power sliding door is opened or closed.
For details, contact your Toyota dealer.
Front overhead console (type A)
D Careful attention is needed so as
not to get your fingers trapped as
the sliding door automatically opens
or closes.
D Never allow a child to operate the
sliding door.
30
Front overhead console (type B)
2008 SIENNA from Aug. ’08 Prod. (OM45455U)
Loading...