Toyota Sienna 2002 Owner's Manual

02 SIENNA_U (L/O 0107)

Foreword

Welcome to the growing group of value−conscious people who drive Toyotas. We are proud of the advanced engineering and quality construction of each vehicle we build.

This Owner’s Manual explains the operation of your new Toyota. Please read it thoroughly and have all the occupants follow the instructions carefully. Doing so will help you enjoy many years of safe and trouble−free motoring. For important information about this manual and your Toyota, read the following pages carefully.

When it comes to service, remember that your Toyota dealer knows your vehicle best and is interested in your complete satisfaction. He will provide quality maintenance and any other assistance you may require.

If there is not a Toyota dealer near you, or you need emergency assistance for any reason, please call the following number:

D U.S. OWNERS: Toyota Customer Assistance Center Tol l −free:1−800−331−4331 D CANADIAN OWNERS: Toyota Canada Customer Interaction Centre Toll−free:1−888−TOYOTA−8 (1−888−869−6828)

Please leave this Owner’s Manual in this vehicle at the time of resale. The next owner will need this information also.

All information and specifications in this manual are current at the time of printing. However, because of Toyota’s policy of continual product improvement, we reserve the right to make changes at any time without notice.

Please note that this manual applies to all models and explains all equipment, including options. Therefore, you may find some explanations for equipment not installed on your vehicle.

2002 MY SIENNA_U (OM45407U)

02 SIENNA_U (L/O 0107)

Important information about this manual

Safety and vehicle damage warnings

Throughout this manual, you will see safety and vehicle damage warnings. You must follow these warnings carefully to avoid possible injury or damage.

The types of warnings, what they look like, and how they are used in this manual are explained as follows:

CAUTION

This is a warning against something which may cause injury to people if the warning is ignored. You are informed about what you must or must not do in order to avoid or reduce the risk to yourself and other people.

NOTICE

This is a warning against something which may cause damage to the vehicle or its equipment if the warning is ignored. You are informed about what you must or must not do in order to avoid or reduce the risk of damage to your vehicle and its equipment.

Safety symbol

When you see the safety symbol shown above, it means: “Do not...”; “Do not do this”; or “Do not let this happen”.

2002 MY SIENNA_U (OM45407U)

02 SIENNA_U (L/O 0107)

Important information about your Toyota

New vehicle warranty

Your new vehicle is covered by the following Toyota limited warranties:

D New vehicle warranty

D Emission control systems warranty

D Others

For further information, please refer to the “Owner’s Warranty Information Booklet” or “Owner’s Manual Supplement”.

Your responsibility for

maintenance

It is the owner’s responsibility to make sure that the specified maintenance is performed. Section 6 gives details of these maintenance requirements. Also included in Section 6 is general maintenance. For scheduled maintenance information, please refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.

Accessories, spare parts and

modification of your Toyota

A wide variety of non−genuine spare parts and accessories for Toyota vehicles are currently available in the market. You should know that Toyota does not warrant these products and is not responsible for their performance, repair, or replacement, or for any damage they may cause to, or adverse effect they may have on, your Toyota vehicle.

This vehicle should not be modified with non−genuine Toyota products. Modification with non−genuine Toyota products could affect its performance, safety or durability, and may even violate governmental regulations. In addition, damage or performance problems resulting from the modification may not be covered under warranty.

iii

2002 MY SIENNA_U (OM45407U)

02 SIENNA_U (L/O 0107)

Spark ignition system of your

Toyota

The spark ignition system in your Toyota meets all requirements of the Canadian Interference−Causing Equipment Standard.

Installation of a mobile

two−way radio system

As the installation of a mobile two−way radio system in your vehicle could affect electronic systems such as multiport fuel injection system/sequential multiport fuel injection system, cruise control system, anti−lock brake system, traction control system, vehicle skid control system, SRS airbag system and seat belt pretensioner system, be sure to check with your Toyota dealer for precautionary measures or special instructions regarding installation.

Scrapping of your Toyota

The SRS airbag and seat belt pretensioner devices in your Toyota contain explosive chemicals. If the vehicle is scrapped with the airbags and pretensioners left as they are, this may cause an accident such as fire. Be sure to have the systems of the SRS airbag and seat belt pretensioner removed and disposed of by the qualified service shop or by your Toyota dealer before you dispose of your vehicle.

2002 MY SIENNA_U (OM45407U)

02 SIENNA_U (L/O 0107)

SECTION 1− 1

OPERATION OF INSTRUMENTS AND CONTROLS

Overview of instruments and controls

Instrument panel overview 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Instrument cluster overview 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Indicator symbols on the instrument panel 7. . . . . . . . . . . . . . . . . . . . . . .

2002 MY SIENNA_U (OM45407U)

Instrument panel overview

02 SIENNA_U (L/O 0107)

1. Side defroster outlets

2. Side vents

3. Instrument cluster

4. Automatic transmission selector lever

5. Center vents

6. Garage door opener, garage door opener box or auxiliary box

7. Electric moon roof switch, front personal light or front interior light switch

8. Front personal lights or front interior light

9. Power door lock switches

10. Power window switches

11. G l o v e b o x

12. Auxiliary boxes

13. Tilt steering lock release lever

14. Hood lock release lever

15. Parking brake pedal

16. Window lock switch

2002 MY SIENNA_U (OM45407U)

02 SIENNA_U (L/O 0107)

1. Headlight, turn signal and front fog light switches

2. Wiper and washer switches

3. Clock and front passenger ’s seat belt reminder light

4. Emergency flasher switch

5. Front air conditioning controls

6. Rear fan speed selector or rear fan position selector

7. Rear window and outside rear view mirror defoggers switch

8. Car audio

9. Seat heater switches

10. Ashtray

11. Power sliding door switches

12. Power outlet

13. Cigarette lighter

14. Power rear quarter window switch

15. Ignition switch

16. Cruise control switch

17. Audio remote control buttons

18. Power sliding door off switch

2002 MY SIENNA_U (OM45407U)

19. Tire pressure warning system reset switch or traction control system off switch

20. Theft deterrent system/Engine immobiliser system indicator light

21. Power rear view mirror control switches

22. Instrument panel light control dial

02 SIENNA_U (L/O 0107)

2002 MY SIENNA_U (OM45407U)

Instrument cluster overview

"With tachometer

02 SIENNA_U (L/O 0107)

1. Engine coolant temperature gauge

2. Tachometer

3. Service reminder indicators and indicator lights

4. Speedometer

5. Fuel gauge

6. Trip meter reset knob

2002 MY SIENNA_U (OM45407U)

7. Odometer and two trip meters

"Without tachometer

02 SIENNA_U (L/O 0107)

1. Engine coolant temperature gauge

2. Service reminder indicators and indicator lights

3. Speedometer

4. Odometer and two trip meters

5. Fuel gauge

6. Trip meter reset knob

2002 MY SIENNA_U (OM45407U)

Indicator symbols on the instrument panel

02 SIENNA_U (L/O 0107)

Brake system warning light

Driver ’s seat belt reminder light

Front passenger’s seat belt reminder light

Discharge warning light

∗

or Malfunction indicator lamp

Low fuel level warning light

Low engine oil pressure warning light

∗

or Anti−lock brake system warning light

∗

Open door warning light

Open power sliding door warning light

∗

SRS warning light

Vehicle skid control system/traction control system warning light

∗

Low windshield washer fluid level warning light

∗

Low tire pressure warning light

Turn signal indicator lights

∗

2002 MY SIENNA_U (OM45407U)

Headlight high beam indicator light

Overdrive−off indicator light

∗

Cruise control indicator light

Automatic transmission indicator lights

Slip indicator light

Traction control system off indicator light

∗

: For details, see “Service reminder indicators and warning

buzzers” in Section 1−5.

∗

: If this light flashes, see “Cruise control” in Section 1−6.

02 SIENNA_U (L/O 0107)

2002 MY SIENNA_U (OM45407U)

02 SIENNA_U (L/O 0107)

SECTION 1− 2

OPERATION OF INSTRUMENTS AND CONTROLS

Keys and Doors

Keys 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Engine immobiliser system 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Front doors 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Sliding door 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Power sliding door 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Wireless remote control 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Power windows 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Power rear quarter windows 32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Center side windows and manual rear quarter windows 33. . . . . . . . . .

Back door 33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Hood 34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Theft deterrent system 35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Fuel tank cap 37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Electric moon roof 39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2002 MY SIENNA_U (OM45407U)

02 SIENNA_U (L/O 0107)

Keys (without engine immobiliser system)

Your vehicle is supplied with two kinds of keys.

1. Master key—This key works in every lock.

2. Sub key—This key will not work in the glove box.

To protect things locked in the glove box when you have your vehicle parked, leave the sub key with the attendant.

Since the front doors and sliding doors can be locked without a key, you should always carry a spare master key in case you accidentally lock your keys inside the vehicle.

KEY NUMBER PLATE

Your key number is shown on the plate. Keep the plate in a safe place such as your wallet, not in the vehicle.

If you should lose your keys or if you need additional keys, duplicates can be made by a Toyota dealer using the key number.

We recommend you to write down the key number and keep it in safe place.

Keys (with engine immobiliser system)

Your vehicle is supplied with two kinds of keys.

1. Master key (black)—This key works in every lock. Your Toyota dealer will need it to make you a new key with built−in transponder chip.

2. Sub key (gray)—This key will not work in the glove box.

A transponder chip for engine immobiliser system has been filled in the head of the master and sub keys. These chips are needed to enable the system to function correctly, so be careful not to lose these keys. If you make your own duplicate key, you will not be able to cancel the system or start the engine.

2002 MY SIENNA_U (OM45407U)

To protect things locked in the glove box when you have your vehicle parked, leave the sub key with the attendant.

Since the front doors and sliding doors can be locked without a key, you should always carry a spare master key in case you accidentally lock your keys inside the vehicle.

02 SIENNA_U (L/O 0107)

NOTICE

When using a key containing a transponder chip, observe the following precautions:

z When starting the engine, do not

use the key with a key ring resting on the key grip and do not press the key ring against the key grip. Otherwise the engine may not start, or may stop soon after it starts.

2002 MY SIENNA_U (OM45407U)

z When starting the engine, do not

use the key with other transponder keys around (including keys of other vehicles) and do not press other key plates against the key grip. Otherwise the engine may not start, or may stop soon after it starts. If this happens, remove the key once and then insert it again after taking off other transponder keys (including keys of other vehicles) from the ring or while gripping or covering them with your hand to start the engine.

z Do not bend the key grip.

02 SIENNA_U (L/O 0107)

z Do not cover the key grip with any

material that cuts off electromagnetic waves.

z Do not knock the key hard against

other objects.

z Do not leave the key exposed to

high temperatures for a long period, such as on the dashboard and hood under the direct sunlight.

z Do not put the key in water or

wash it in an ultrasonic washer.

z Do not use the key with electromag-

netic materials.

KEY NUMBER PLATE

Your key number is shown on the plate. Keep the plate in a safe place such as your wallet, not in the vehicle.

If you should lose your keys or if you need additional keys, duplicates can be made by a Toyota dealer using the key number.

We recommend you to write down the key number and keep it in safe place.

2002 MY SIENNA_U (OM45407U)

Engine immobiliser system

The engine immobiliser system is a theft prevention system. When you insert the key in the ignition switch, the transponder chip in the key’s head transmits an electronic code to the vehicle. The engine will start, only when the electronic code in the chip corresponds to the registered ID code for the vehicle.

02 SIENNA_U (L/O 0107)

The system is automatically set when the key is removed from the ignition switch. The indicator light will start flashing to show the system is set.

If any of the following indicator conditions occurs, contact your Toyota dealer.

D The indicator light stays on except

when the theft deterrent system is setting or activating. (See “Theft deterrent system”.)

D The indicator light does not start flash-

ing when the key is removed from the ignition switch.

D The indicator light flashes unsteady.

Inserting the registered key in the ignition switch automatically cancels the system, which enables the engine to start. The indicator light will go off.

For your Toyota dealer to make you a new key with built−in transponder chip, your dealer will need your key number and master key. However, there is a limit to the number of additional keys your Toyota dealer can make for you.

If you make your own duplicate key, you will not be able to cancel the system or start the engine.

NOTICE

Do not modify, remove or disassemble the engine immobiliser system. If any unauthorized changes or modifications are made, the proper operation of the system cannot be guaranteed.

2002 MY SIENNA_U (OM45407U)

For vehicles sold in U.S.A.

02 SIENNA_U (L/O 0107)

Front doors

For vehicles sold in Canada

FCC ID: MOZ RI−4BTY MADE IN JAPAN

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with RSS−210 of Industry Canada. Operation is subject to the following two conditions:

(1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

LOCKING AND UNLOCKING WITH KEY

Insert the key into the keyhole and turn it.

To lock: Turn the key forward. To unlock: Turn the key backward.

Vehicles with power door lock system—All the doors lock and unlock simultaneously with either front door. In the driver’s door lock, turning the key once will unlock the driver’s door and twice in succession will unlock all the doors simultaneously.

2002 MY SIENNA_U (OM45407U)

LOCKING AND UNLOCKING WITH INSIDE LOCK KNOB

Move the lock knob.

To lock: Push the knob forward. To unlock: Pull the knob backward.

Closing the front door with the lock knob in the lock position will also lock the front door. Be careful not to lock your keys in the vehicle.

Vehicles with power door lock system—The door cannot be locked if you leave the key in the ignition switch.

Driver’s side

02 SIENNA_U (L/O 0107)

LOCKING AND UNLOCKING WITH POWER DOOR LOCK SWITCH

Push the switch.

To lock: Push the switch on the front side. To unlock: Push the switch on the rear side.

All the doors lock or unlock simultaneously.

CAUTION

Before driving, be sure that the doors are closed and locked, especially when small children are in the vehicle. Along with the proper use of seat belts, locking the doors helps prevent the driver and passengers from being thrown out from the vehicle during an accident. It also helps prevent the doors from being opened unintentionally.

Passenger’s side

2002 MY SIENNA_U (OM45407U)

Sliding door

02 SIENNA_U (L/O 0107)

CLOSING FROM OUTSIDE

To close the fully−opened sliding door, pull the outside handle toward you and then close the door.

Lock release button

LOCKING AND UNLOCKING WITH KEY (on some models)

Insert the key into the keyhole and turn it.

To lock: Turn the key forward. To unlock: Turn the key backward.

LOCKING AND UNLOCKING WITH INSIDE LOCK KNOB

Move the lock knob.

To lock: Push the knob downward. To unlock: Push the knob upward.

To open the sliding door, push the lock release button and then open the door.

2002 MY SIENNA_U (OM45407U)

02 SIENNA_U (L/O 0107)

Vehicles with power door lock system—The sliding doors will be locked simultaneously when either front door or the back door is locked with the power door lock switch or key. If you lock either front door or the back door with the power door lock switch or key while the sliding door is open, the sliding door will be locked after it is closed. (For instructions, see “Front doors” or “Back door” in this section.)

Closing the sliding door with the lock knob in the lock position will also lock the sliding door. Be careful not to lock your keys in the vehicle.

CLOSING FROM INSIDE

To close the fully−opened sliding door, push the lock release button and then close the door.

CAUTION

D When closing the sliding door, con-

firm safety of the area around. Keep the heads, hands and other parts of the bodies of all occupants away from the sliding door. Otherwise, they will be possibly caught and pinched by the closing door causing an unexpected serious injury.

D When the vehicle is stopped on a

gradient, the door will slide faster when opening or closing, so be especially careful that the passengers do not get hit or pinched by the door.

D When stopping on a downward

slope, open the door fully while passengers are getting on or off. Do not pull the outside handle or push the lock release button while the door is open as the door could suddenly close by itself causing injury.

NOTICE

Do not close the sliding door by applying the brakes. Doing so could cause the door to be damaged.

2002 MY SIENNA_U (OM45407U)

HALF−OPENED SLIDING DOOR STOPPER

When opening the left side sliding door, it stops at the half−opened position if the fuel filler door is opened.

Left and right side power sliding door models—The left side power sliding door does not operate when the fuel filler door is open.

02 SIENNA_U (L/O 0107)

SLIDING DOOR CHILD−PROTECTORS

Open the sliding door fully and move the lock lever to the “LOCK” position as shown on the label. Then close the sliding door.

If the child−protector is locked, you cannot open the sliding door from the inside. We recommend using this feature whenever small children are in the vehicle.

Vehicles with power sliding door system— If the power sliding door system is on, the child−protector feature is cancelled when someone pushes one of the “DOOR L”, “DOOR R” and “PWR DOOR” switches inside the vehicle or “POWER DOOR”, “D−PWR DOOR” and “P−PWR DOOR” switches of the wireless remote control transmitter. (For details, see “Power sliding door” in this section.)

CAUTION

Make sure to turn off the power sliding door system after locking the child−protectors.

NOTICE

Avoid forcibly opening the left side sliding door fully when refueling. Otherwise, the fuel filler door may be damaged.

2002 MY SIENNA_U (OM45407U)

Power sliding door

Some vehicles are equipped with a power sliding door. This system has the following functions:

D The power sliding door can be oper-

ated with the “DOOR L”, “DOOR R” and “PWR DOOR” switches inside the vehicle or “POWER DOOR”, “D−PWR DOOR” and “P−PWR DOOR” switches of the wireless remote control transmitter. (For details about the wireless remote control transmitter, see “Wireless remote control” in this section.)

D If you move the sliding door to the

opening or closing direction by hand, the sliding door will automatically and completely open or close after you let go of the sliding door.

CAUTION

Do not leave small children or pets unattended in your vehicle. They could operate the power sliding door, and they themselves or others could be injured. Turn off the power sliding door system when the power sliding door is not in use.

02 SIENNA_U (L/O 0107)

“PWR DOOR OFF” SWITCH

This switch is used to turn on and off the power sliding door system. For operating the power sliding door, the “PWR DOOR OFF” switch on the instrument panel must be pushed out. (The orange line on the top of the switch indicates that the system is on.) To disable the power sliding door feature, push in the switch.

When the power sliding door system is on, you can open and close the sliding door with the “DOOR L”, “DOOR R” and “PWR DOOR” switches inside the vehicle or “POWER DOOR”, “D−PWR DOOR” and “P−PWR DOOR” switches of the wireless remote control transmitter even if the sliding door child−protector is locked. If small children or pets are in the vehicle, turn off the system to prevent the accidental operation of the door.

CAUTION

When jacking up the vehicle, turn off the power sliding door system and close the sliding door completely.

NOTICE

When your vehicle goes through an automatic car wash, make sure the power sliding door system is off.

2002 MY SIENNA_U (OM45407U)

02 SIENNA_U (L/O 0107)

Instrument panel

Center pillar

OPENING AND CLOSING WITH “DOOR L”, “DOOR R” AND “PWR DOOR” SWITCHES

Push the switch. The power sliding door opens and closes completely.

Left side power sliding door—

To open: Push the “DOOR L” switch or “PWR DOOR” switch of the left side center pillar. To close: Push the “DOOR L” switch or “PWR DOOR” switch of the left side center pillar again.

Right side power sliding door—

To open: Push the “DOOR R” switch or “PWR DOOR” switch of the right side center pillar. To close: Push the “DOOR R” switch or “PWR DOOR” switch of the right side center pillar again.

Opening and closing can be performed by the “DOOR L”, “DOOR R” and “PWR DOOR” switches under the following conditions:

D The sliding door is unlocked. D The power sliding door system is on.

(The “PWR DOOR OFF” switch is pushed out.)

D To open the power sliding door when

the ignition key is in the “ON” position, the transmission selector lever must be in “P”. (To close the sliding door from the fully−opened or half−opened position, the transmission selector lever is not required to be in “P”.)

Left and right side power sliding door models—The left side power sliding door does not operate when the fuel filler door is opened.

CAUTION

If you shift the automatic transmission selector lever out of “P” and accelerate before the power sliding door is closed completely, the sliding door may reverse to the open position. A child or others could fall out of the vehicle and be injured. Always make sure the power sliding door is closed and latched before you start driving.

2002 MY SIENNA_U (OM45407U)

02 SIENNA_U (L/O 0107)

OPENING BY HAND

When the power sliding door system is on, if you pull the outside door handle or push the inside lock release button to release the sliding door, it will then automatically and completely open.

When the power sliding door system is off, open the sliding door as usual.

CLOSING BY HAND

When the power sliding door system is on, if you slide the door about 10 cm (4 in.) to the closing direction and let the door go, it will automatically and completely close.

When the power sliding door system is off, close the sliding door as usual.

OPEN POWER SLIDING DOOR WARNING LIGHT AND BUZZER

This light on the instrument panel comes on if the power sliding door is not completely closed with the ignition key in the “ON” position. (See “Service reminder indicators and warning buzzers” in Section 1−5.)

If you forcibly close the power sliding door by hand when the ignition key is in the “ON” position, the open power sliding door warning light may stay on. In this case, try opening and closing the power sliding door again by hand slowly, or use one of the “DOOR L”, “DOOR R” and “PWR DOOR” switches inside the vehicle or “POWER DOOR”, “D−PWR DOOR” and “P−PWR DOOR” switches of the wireless remote control transmitter.

If you shift out of “P” when the power sliding door is opened or in the process of closing with the power sliding door system on, a buzzer will sound and the open power sliding door warning light will flash. This is a warning that the sliding door is not completely closed.

2002 MY SIENNA_U (OM45407U)

02 SIENNA_U (L/O 0107)

JAM PROTECTION FUNCTION

If anything with sufficient resistance obstructs the power sliding door while it is closing or opening, the sliding door will automatically reverse to the opposite direction. However, if the power sliding door is between the fully−closed and half− opened positions while it is opening, the door will stop at that position.

Before operating the power sliding door, make sure there is nobody near the sliding door. Make sure the sliding door stops at the fully−opened position, and then allow the passengers to get on and off the vehicle.

The resistance must be as strong as the force of the moving door, or stronger. As the sliding door approaches the fully− closed or fully−opened position, its moving force increases significantly.

If the sliding door receives a strong impact, this function may work even if nothing is caught.

CAUTION

Power sliding door could injure people if they are caught in the door path. When using the power sliding door, observe the following:

D Never try jamming any part of your

body to make the jam protection function work intentionally.

D The jam protection function may

not work if something gets caught just before the sliding door is fully closed.

D You must always make sure the

heads, hands and other parts of the bodies of all occupants are away from the sliding door. If someone’s neck, head or hand gets caught in a closing sliding door, it could result in a serious injury. When anyone closes the power sliding door, make sure he/she operates the sliding door safely.

NOTICE

Objects caught in the path of the sliding door may be damaged. Make sure there is nothing in the doorway before closing the sliding door.

2002 MY SIENNA_U (OM45407U)

02 SIENNA_U (L/O 0107)

CAUTION

When the vehicle is stopped on a downward slope of a steep grade (17% or more), the sliding door may not stay in the fully−opened position and could suddenly close by itself, possibly resulting a personal injury. Making sure the sliding door does not close abruptly, turn on the power sliding door system. Then the sliding door will operate under the control of the electric power.

RESETTING THE POWER SLIDING DOOR SYSTEM

If the power sliding door system operates incorrectly or does not operate under the following conditions, the system must be initialized and reset by the steps in the next column.

D The battery is disconnected and then

reconnected, or a discharged battery is recharged.

In this case, initialize and reset the system by doing the following steps from 6 to 10.

D The open power sliding door warning

light stays on though the sliding door is closed.

In this case, initialize and reset the system by doing the following steps from 1 to 10.

CAUTION

To initialize and reset power sliding door system, stop the vehicle on a level ground.

1. Be sure to turn off the power sliding door system by pushing in the “PWR DOOR OFF” switch.

2. Disconnect the battery for 1 minute and then reconnect it.

3. Close the sliding door by hand.

(Step 3 can be performed before step

2.)

4. Turn on the power sliding door system by pushing out the “PWR DOOR OFF” switch.

5. Wait 5 seconds.

6. Open the sliding door by using one of the “DOOR L”, “DOOR R” and “PWR DOOR” switches.

7. Wait 3 seconds after the sliding door stops at the fully−opened position.

8. Close the sliding door by using one of the “DOOR L”, “DOOR R” and “PWR DOOR” switches inside the vehicle or “POWER DOOR”, “D−PWR DOOR” and “P−PWR DOOR” switches of the wireless remote control transmitter.

9. Wait 3 seconds after the sliding door stops at the fully−closed position.

10. Repeat the steps from 6 to 9.

2002 MY SIENNA_U (OM45407U)

If the power sliding door system does not operate properly after the above procedure, there may be a problem in the system. Contact your Toyota dealer.

02 SIENNA_U (L/O 0107)

Wireless remote control

Locking operation

Unlocking operation

2002 MY SIENNA_U (OM45407U)

The wireless remote control system allows you to lock or unlock all the doors from a distance within approximately 1 m (3 ft.) of the vehicle. On some models, the system also allows you to activate the theft deterrent system from the same distance.

LOCKING AND UNLOCKING THE DOORS

To lock and unlock all the doors, push the switches of the transmitter slowly and securely.

To lock: Push the “LOCK” switch. All the doors are locked simultaneously. At this time one beep will be heard, parking lights, side marker lights, tail lights and other exterior lights will flash once.

Left and right side power sliding door models—If the “LOCK” switch is kept pressed in, the panic mode will work. (For details, see “PANIC (LOCK)” SWITCH.)

Check to see that the doors are securely locked.

If any of the doors is not securely closed, or if the key is in the ignition switch, locking cannot be performed by the “LOCK” switch and a beep will sound continuously for 10 seconds. However, if the key is in the ignition, a beep will not sound.

02 SIENNA_U (L/O 0107)

To stop the beep, close all the doors securely or push the “UNLOCK” switch.

To unlock: Push the “UNLOCK” switch once to unlock only the driver’s door. Pushing the switch twice within 3 seconds unlocks all the doors simultaneously. Each time the “UNLOCK” switch is pushed, two beeps will be heard, and the parking lights, side marker lights and tail lights will flash twice.

When the “UNLOCK” switch is pressed, the personal lights, interior lights and/or ignition key light come on. The lights remains on for about 15 seconds unless any of the doors are opened then and closed. (For further information, see “Personal lights”, “Interior lights” and/or “Ignition switch light” in Section 1−4.)

You have 30 seconds to open a door after using the wireless remote unlock feature. If a door is not opened by then, all the doors will automatically lock again.

If the “LOCK” or “UNLOCK” switch is kept pressed in, the locking or unlocking operation is not repeated. Release the button and then push again.

SWITCHING BEEP SOUND ON AND OFF

You can switch the beep on and off. (The beep is on initially and after battery replacement.)

To switch the beep on and off:

With the driver’s door opened—

1. Insert the ignition key and remove it.

2. Within 5 seconds, insert the ignition key again and turn it to the “ON” position.

3. After 10 seconds, push the same “LOCK”, “UNLOCK” or “PANIC” button twice within 10 seconds. Two beep sounds inform you that the program has been switched on or off.

If this procedure is not followed exactly, the beep will not operate as expected.

Check the beep ON/OFF operation by pushing the wireless remote control transmitter switch after you finish this procedure. If the beep does not operate as expected, repeat this procedure from step

Right side power sliding door models

2002 MY SIENNA_U (OM45407U)

Left and right side power sliding door models

02 SIENNA_U (L/O 0107)

OPENING AND CLOSING WITH “POWER DOOR”, “D−PWR DOOR” AND “P−PWR DOOR” SWITCHES (on some models)

Push the switch of the wireless remote control transmitter slowly and securely. The power sliding door opens and closes completely.

Left side power sliding door—

To open: Push the “D−PWR DOOR” switch. To close: Push the “D−PWR DOOR” switch again.

Right side power sliding door—

To open: Push the “P−PWR DOOR” switch or “PWR DOOR” switch. To close: Push the “P−PWR DOOR” switch or “PWR DOOR” switch again.

Opening and closing can be performed by the “POWER DOOR”, “D−PWR DOOR” and “P−PWR DOOR” switches under the following conditions only:

D The sliding door is unlocked. D The power sliding door system is on.

(The “PWR DOOR OFF” switch is pushed out.)

D The ignition key is not in the “ON”

position.

Left and right side power sliding door models—The left side power sliding door does not operate when the fuel filler door is opened.

“PANIC (LOCK)” SWITCH (left and right side power sliding door models)

Pushing and holding the “PANIC (LOCK)” switch blows the horn intermittently and flashes the headlights, tail lights and other exterior lights.

The “PANIC (LOCK)” switch is used to deter vehicle theft when you witness anyone attempting to break into or damage your vehicle.

2002 MY SIENNA_U (OM45407U)

+ 304 hidden pages