Toyota SIENNA 2002 Owner Manual
02 SIENNA_U (L/O 0107)
SECTION 1–
OPERATION OF INSTRUMENT S AND
CONTROLS
Overview of instruments and controls
Instrument panel o verview 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument cluster overview 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Indicator symbols on the instrument panel 7. . . . . . . . . . . . . . . . . . . . . . .
1
2002 MY SIENNA_U (OM45407U)
1
Instrument panel overview
02 SIENNA_U (L/O 0107)
1. Side defroster outlets
2. Side vents
3. Instrument cluster
4. Automatic transmission selector lever
5. Center vents
6. Garage door opener, gar age door
opener box or auxiliary box
7. Electric moon roof switch, front
personal light or front interior light
switch
8. Front personal lights or front interior
light
9. Power door lock switches
10. Power window switches
11 . G lo ve b ox
12. Auxiliary boxes
13. Tilt steering lock release lever
14. Hood lock release lever
15. Parking b rake pedal
16. Window lock switch
2
2002 MY SIENNA_U (OM45407U)
02 SIENNA_U (L/O 0107)
1. Headlight, turn signal and front fog
light switches
2. Wiper and washer switches
3. Clock and front passenger ’s seat belt
reminder light
4. Emergency flasher switch
5. Front air conditioning controls
6. Rear fan speed selector or rear fan
position selector
7. Rear window and outside rear view
mirror defoggers switch
8. Car audio
9. Seat heater switches
10. Ashtray
11. Power sliding door switches
12. Power outlet
13. Cigarette lighter
14. Power rear quarter window switch
15. Ignition switch
16. Cruise control switch
17. Audio remote control buttons
18. Power sliding door off switch
2002 MY SIENNA_U (OM45407U)
3
19. Tire pressure warning system reset
switch or t raction cont rol syst em off
switch
20. Theft deterrent system/Engine
immobiliser system indicator light
21. Power rear view mirror control switches
22. Instrument panel light control dial
02 SIENNA_U (L/O 0107)
4
2002 MY SIENNA_U (OM45407U)
Instrument cluster overview
With tachometer
02 SIENNA_U (L/O 0107)
1. Engine coolant temperature gauge
2. Tachometer
3. Service reminder indicators and
indicator lights
4. Speedometer
5. Fuel gauge
6. Trip m eter res et knob
2002 MY SIENNA_U (OM45407U)
7. Odometer and two trip meters
5
Without tachometer
02 SIENNA_U (L/O 0107)
1. Engine coolant temperature gauge
2. Service reminder indicators and
indicator lights
3. Speedometer
6
4. Odometer and two trip meters
5. Fuel gauge
6. Trip m eter res et knob
2002 MY SIENNA_U (OM45407U)
Indicator symbols on the instrument panel
02 SIENNA_U (L/O 0107)
or
Brake system warning light
Driver’s seat belt reminder light
Front passenger’s seat belt reminder light
Discharge warning light
∗
or Malfunction indicator lamp
Low fuel level warning light
Low engine oil pressure warning light
∗
1
∗
1
∗
1
1
∗
1
or Anti–lock brake system warning light
∗
Open door warning light
1
Open power sliding door warning light
∗
SRS warning light
Vehicle skid control system/traction control
system warning light
1
∗
1
Low windshield washer fluid level warning light
∗
1
∗
1
Low tire pressure warning light
Turn signal indicator lights
∗
1
∗
1
∗
1
∗
1
2002 MY SIENNA_U (OM45407U)
7
Headlight high beam indicator light
Overdrive–off indicator light
∗
Cruise control indicator light
2
Automatic transmission indicator lights
Slip indicator light
Traction control system off indicator light
∗
1
: For details, see “Service reminder indicators and warning
buzzers” in Section 1–5.
∗
2
: If this light flashes, see “Cruise control” in Section 1–6.
02 SIENNA_U (L/O 0107)
8
2002 MY SIENNA_U (OM45407U)
02 SIENNA_U (L/O 0107)
SECTION 1–
OPERATION OF INSTRUMENT S AND
CONTROLS
Keys and Doors
Keys 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine immobiliser system 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front door s 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sliding door 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power sliding door 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wireless remote control 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power windows 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power rear quarter windows 32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Center si de windows and manual rear quart er windows 33. . . . . . . . . .
Back door 33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hood 34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Theft deterrent s ystem 35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel tank cap 37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
Electric moon roof 39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2002 MY SIENNA_U (OM45407U)
9
02 SIENNA_U (L/O 0107)
Keys (without engine
immobiliser system)
Your vehicle is supplied with two kinds
of keys.
1. Master key—This key works in every
lock.
2. Sub key—This key will not work in the
glove box.
To protect things locked in the glove box
when you have your vehicle parked, leave
the sub key with the attendant.
Since the front doors and sliding doors
can be locked without a key, you should
always carry a spare master key in case
you accidentally lock your keys inside the
vehicle.
KEY NUMBER PLATE
Your key number is shown on the plate.
Keep the plate in a safe place such as
your wallet, not in the vehicle.
If you should lose your keys or if you
need additional keys, duplicates can be
made by a Toyota dealer using the key
number.
We recommend you to write down the key
number and keep it in safe place.
Keys (with engine immobiliser
system)
Your vehicle is supplied with two kinds
of keys.
1. Master key (black)—This key works in
every lock. Your Toyota dealer will
need it to make you a new key with
built–in transponder chip.
2. Sub key (gray)—This key will not work
in the glove box.
A transponder chip for engine immobiliser
system has been filled in the head of the
master and sub keys. These chips are
needed to enable the system to function
correctly, so be careful not to lose these
keys. If you make your own duplicate key,
you will not be able to cancel the system
or start the engine.
10
2002 MY SIENNA_U (OM45407U)
To protect things locked in the glove box
when you have your vehicle parked, leave
the sub key with the attendant.
Since the front doors and sliding doors
can be locked without a key, you should
always carry a spare master key in case
you accidentally lock your keys inside the
vehicle.
02 SIENNA_U (L/O 0107)
NOTICE
When using a key containing a transponder chip, observe the following
precautions:
When starting the engine, do not
use the key with a key ring resting
on the key grip and do not press
the key ring against the key grip.
Otherwise the engine may not start,
or may stop soon after it starts.
2002 MY SIENNA_U (OM45407U)
When starting the engine, do not
use the key with other transponder
keys around (including keys of other vehicles) and do not press other
key plates against the key grip.
Otherwise the engine may not start,
or may stop soon after it starts. If
this happens, remove the key once
and then insert it again after taking
off other transponder keys (including keys of other vehicles) from the
ring or while gripping or covering
them with your hand to start the
engine.
11
Do not bend the key grip.
02 SIENNA_U (L/O 0107)
Do not cover the key grip with any
material that cuts off electromagnetic waves.
Do not knock the key hard against
other objects.
Do not leave the key exposed to
high temperatures for a long period,
such as on the dashboard and hood
under the direct sunlight.
Do not put the key in water or
wash it in an ultrasonic washer.
Do not use the key with electromagnetic materials.
KEY NUMBER PLATE
Your key number is shown on the plate.
Keep the plate in a safe place such as
your wallet, not in the vehicle.
If you should lose your keys or if you
need additional keys, duplicates can be
made by a Toyota dealer using the key
number.
We recommend you to write down the key
number and keep it in safe place.
12
2002 MY SIENNA_U (OM45407U)
Engine immobiliser system
The engine immobiliser system is a
theft prevention system. When you insert the key in the ignition switch, the
transponder chip in the key’s head
transmits an electronic code to the vehicle. The engine will start, only when
the electronic code in the chip corresponds to the registered ID code for
the vehicle.
02 SIENNA_U (L/O 0107)
The system is automatically set when the
key is removed from the ignition switch.
The indicator light will start flashing to
show the system is set.
If any of the following indicator conditions
occurs, contact your Toyota dealer.
The indicator light stays on except
when the theft deterrent system is setting or activating. (See “Theft deterrent
system”.)
The indicator light does not start flash-
ing when the key is removed from the
ignition switch.
The indicator light flashes unsteady.
Inserting the registered key in the ignition
switch automatically cancels the system,
which enables the engine to start. The
indicator light will go off.
For your Toyota dealer to make you a
new key with built–in transponder chip,
your dealer will need your key number
and master key. However, there is a limit
to the number of additional keys your
Toyota dealer can make for you.
If you make your own duplicate key,
you will not be able to cancel the system or start the engine.
NOTICE
Do not modify, remove or disassemble the engine immobiliser system. If any unauthorized changes or
modifications are made, the proper
operation of the system cannot be
guaranteed.
2002 MY SIENNA_U (OM45407U)
13
For vehicles sold in U.S.A.
02 SIENNA_U (L/O 0107)
Front doors
For vehicles sold in Canada
FCC ID: MOZ RI–4BTY
MADE IN JAPAN
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
CAUTION
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
This device complies with RSS–210 of
Industry Canada. Operation is subject to
the following two conditions:
(1) This device may not cause interference, and (2) this device must accept
any interference, including interference
that may cause undesired operation of
the device.
LOCKING AND UNLOCKING WITH KEY
Insert the key into the keyhole and turn
it.
To lock: Turn the key forward.
To unlock: Turn the key backward.
Vehicles with power door lock system—All
the doors lock and unlock simultaneously
with either front door. In the driver’s door
lock, turning the key once will unlock the
driver’s door and twice in succession will
unlock all the doors simultaneously.
14
2002 MY SIENNA_U (OM45407U)
LOCKING AND UNLOCKING WITH
INSIDE LOCK KNOB
Move the lock knob.
To lock: Push the knob forward.
To unlock: Pull the knob backward.
Closing the front door with the lock knob
in the lock position will also lock the front
door. Be careful not to lock your keys in
the vehicle.
Vehicles with power door lock system—The door cannot be locked if you
leave the key in the ignition switch.
Driver’s side
02 SIENNA_U (L/O 0107)
LOCKING AND UNLOCKING WITH
POWER DOOR LOCK SWITCH
Push the switch.
To lock: Push the switch on the front side.
To unlock: Push the switch on the rear
side.
All the doors lock or unlock simultaneously.
CAUTION
Before driving, be sure that the doors
are closed and locked, especially
when small children are in the vehicle. Along with the proper use of
seat belts, locking the doors helps
prevent the driver and passengers
from being thrown out from the vehicle during an accident. It also helps
prevent the doors from being opened
unintentionally.
Passenger’s side
2002 MY SIENNA_U (OM45407U)
15
Sliding door
02 SIENNA_U (L/O 0107)
CLOSING FROM OUTSIDE
To close the fully–opened sliding door, pull
the outside handle toward you and then
close the door.
Lock release
button
LOCKING AND UNLOCKING WITH KEY
(on some models)
Insert the key into the keyhole and turn
it.
To lock: Turn the key forward.
To unlock: Turn the key backward.
16
LOCKING AND UNLOCKING WITH
INSIDE LOCK KNOB
Move the lock knob.
To lock: Push the knob downward.
To unlock: Push the knob upward.
To open the sliding door, push the lock
release button and then open the door.
2002 MY SIENNA_U (OM45407U)
02 SIENNA_U (L/O 0107)
Vehicles with power door lock system—The sliding doors will be locked simultaneously when either front door or the
back door is locked with the power door
lock switch or key. If you lock either front
door or the back door with the power door
lock switch or key while the sliding door
is open, the sliding door will be locked
after it is closed. (For instructions, see
“Front doors” or “Back door” in this section.)
Closing the sliding door with the lock knob
in the lock position will also lock the sliding door. Be careful not to lock your keys
in the vehicle.
CLOSING FROM INSIDE
To close the fully–opened sliding door,
push the lock release button and then
close the door.
CAUTION
When closing the sliding door, con-
firm safety of the area around.
Keep the heads, hands and other
parts of the bodies of all occupants
away from the sliding door. Otherwise, they will be possibly caught
and pinched by the closing door
causing an unexpected serious injury.
When the vehicle is stopped on a
gradient, the door will slide faster
when opening or closing, so be especially careful that the passengers
do not get hit or pinched by the
door.
When stopping on a downward
slope, open the door fully while
passengers are getting on or off.
Do not pull the outside handle or
push the lock release button while
the door is open as the door could
suddenly close by itself causing injury.
NOTICE
Do not close the sliding door by applying the brakes. Doing so could
cause the door to be damaged.
2002 MY SIENNA_U (OM45407U)
17
HALF–OPENED SLIDING DOOR
STOPPER
When opening the left side sliding door, it
stops at the half–opened position if the
fuel filler door is opened.
Left and right side power sliding door
models—The left side power sliding door
does not operate when the fuel filler door
is open.
02 SIENNA_U (L/O 0107)
SLIDING DOOR CHILD–PROTECTORS
Open the sliding door fully and move
the lock lever to the “LOCK” position
as shown on the label. Then close the
sliding door.
If the child–protector is locked, you cannot
open the sliding door from the inside. We
recommend using this feature whenever
small children are in the vehicle.
Vehicles with power sliding door system—
If the power sliding door system is on, the
child–protector feature is cancelled when
someone pushes one of the “DOOR L”,
“DOOR R” and “PWR DOOR” switches
inside the vehicle or “POWER DOOR”,
“D–PWR DOOR” and “P–PWR DOOR”
switches of the wireless remote control
transmitter. (For details, see “Power
sliding door” in this section.)
CAUTION
Make sure to turn off the power sliding door system after locking the
child–protectors.
NOTICE
Avoid forcibly opening the left side
sliding door fully when refueling.
Otherwise, the fuel filler door may be
damaged.
18
2002 MY SIENNA_U (OM45407U)
Power sliding door
Some vehicles are equipped with a power
sliding door. This system has the following
functions:
The power sliding door can be oper-
ated with the “DOOR L”, “DOOR R”
and “PWR DOOR” switches inside the
vehicle or “POWER DOOR”, “D–PWR
DOOR” and “P–PWR DOOR” switches
of the wireless remote control transmitter. (For details about the wireless remote control transmitter, see “Wireless
remote control” in this section.)
If you move the sliding door to the
opening or closing direction by hand,
the sliding door will automatically and
completely open or close after you let
go of the sliding door.
CAUTION
Do not leave small children or pets
unattended in your vehicle. They
could operate the power sliding door,
and they themselves or others could
be injured. Turn off the power sliding
door system when the power sliding
door is not in use.
02 SIENNA_U (L/O 0107)
“PWR DOOR OFF” SWITCH
This switch is used to turn on and off
the power sliding door system. For operating the power sliding door, the
“PWR DOOR OFF” switch on the instrument panel must be pushed out. (The
orange line on the top of the switch
indicates that the system is on.) To disable the power sliding door feature,
push in the switch.
When the power sliding door system is
on, you can open and close the sliding
door with the “DOOR L”, “DOOR R” and
“PWR DOOR” switches inside the vehicle
or “POWER DOOR”, “D–PWR DOOR” and
“P–PWR DOOR” switches of the wireless
remote control transmitter even if the sliding door child–protector is locked. If small
children or pets are in the vehicle, turn off
the system to prevent the accidental operation of the door.
CAUTION
When jacking up the vehicle, turn off
the power sliding door system and
close the sliding door completely.
NOTICE
When your vehicle goes through an
automatic car wash, make sure the
power sliding door system is off.
2002 MY SIENNA_U (OM45407U)
19
02 SIENNA_U (L/O 0107)
Instrument panel
Center pillar
OPENING AND CLOSING WITH “DOOR
L”, “DOOR R” AND “PWR DOOR”
SWITCHES
Push the switch. The power sliding
door opens and closes completely.
Left side power sliding door—
To open: Push the “DOOR L” switch or
“PWR DOOR” switch of the left side center pillar.
To close: Push the “DOOR L” switch or
“PWR DOOR” switch of the left side center pillar again.
Right side power sliding door—
To open: Push the “DOOR R” switch or
“PWR DOOR” switch of the right side center pillar.
To close: Push the “DOOR R” switch or
“PWR DOOR” switch of the right side center pillar again.
Opening and closing can be performed by
the “DOOR L”, “DOOR R” and “PWR
DOOR” switches under the following conditions:
The sliding door is unlocked.
The power sliding door system is on.
(The “PWR DOOR OFF” switch is
pushed out.)
To open the power sliding door when
the ignition key is in the “ON” position,
the transmission selector lever must be
in “P”. (To close the sliding door from
the fully–opened or half–opened position, the transmission selector lever is
not required to be in “P”.)
Left and right side power sliding door
models—The left side power sliding door
does not operate when the fuel filler door
is opened.
CAUTION
If you shift the automatic transmission selector lever out of “P” and
accelerate before the power sliding
door is closed completely, the sliding
door may reverse to the open position. A child or others could fall out
of the vehicle and be injured. Always
make sure the power sliding door is
closed and latched before you start
driving.
20
2002 MY SIENNA_U (OM45407U)
02 SIENNA_U (L/O 0107)
OPENING BY HAND
When the power sliding door system is
on, if you pull the outside door handle or
push the inside lock release button to release the sliding door, it will then automatically and completely open.
When the power sliding door system is
off, open the sliding door as usual.
CLOSING BY HAND
When the power sliding door system is
on, if you slide the door about 10 cm (4
in.) to the closing direction and let the
door go, it will automatically and completely close.
When the power sliding door system is
off, close the sliding door as usual.
OPEN POWER SLIDING DOOR
WARNING LIGHT AND BUZZER
This light on the instrument panel comes
on if the power sliding door is not completely closed with the ignition key in the
“ON” position. (See “Service reminder indicators and warning buzzers” in Section
1–5.)
If you forcibly close the power sliding door
by hand when the ignition key is in the
“ON” position, the open power sliding door
warning light may stay on. In this case,
try opening and closing the power sliding
door again by hand slowly, or use one of
the “DOOR L”, “DOOR R” and “PWR
DOOR” switches inside the vehicle or
“POWER DOOR”, “D–PWR DOOR” and
“P–PWR DOOR” switches of the wireless
remote control transmitter.
If you shift out of “P” when the power
sliding door is opened or in the process
of closing with the power sliding door system on, a buzzer will sound and the open
power sliding door warning light will flash.
This is a warning that the sliding door is
not completely closed.
2002 MY SIENNA_U (OM45407U)
21
02 SIENNA_U (L/O 0107)
JAM PROTECTION FUNCTION
If anything with sufficient resistance obstructs the power sliding door while it is
closing or opening, the sliding door will
automatically reverse to the opposite direction. However, if the power sliding door
is between the fully–closed and half–
opened positions while it is opening, the
door will stop at that position.
Before operating the power sliding door,
make sure there is nobody near the sliding door. Make sure the sliding door stops
at the fully–opened position, and then allow the passengers to get on and off the
vehicle.
The resistance must be as strong as the
force of the moving door, or stronger. As
the sliding door approaches the fully–
closed or fully–opened position, its moving
force increases significantly.
If the sliding door receives a strong impact, this function may work even if nothing is caught.
CAUTION
Power sliding door could injure
people if they are caught in the door
path. When using the power sliding
door, observe the following:
Never try jamming any part of your
body to make the jam protection
function work intentionally.
The jam protection function may
not work if something gets caught
just before the sliding door is fully
closed.
You must always make sure the
heads, hands and other parts of the
bodies of all occupants are away
from the sliding door. If someone’s
neck, head or hand gets caught in
a closing sliding door, it could result in a serious injury. When anyone closes the power sliding door,
make sure he/she operates the sliding door safely.
NOTICE
Objects caught in the path of the sliding door may be damaged. Make sure
there is nothing in the doorway before closing the sliding door.
22
2002 MY SIENNA_U (OM45407U)
02 SIENNA_U (L/O 0107)
CAUTION
When the vehicle is stopped on a
downward slope of a steep grade
(17% or more), the sliding door may
not stay in the fully–opened position
and could suddenly close by itself,
possibly resulting a personal injury.
Making sure the sliding door does not
close abruptly, turn on the power
sliding door system. Then the sliding
door will operate under the control of
the electric power.
RESETTING THE POWER SLIDING
DOOR SYSTEM
If the power sliding door system operates
incorrectly or does not operate under the
following conditions, the system must be
initialized and reset by the steps in the
next column.
The battery is disconnected and then
reconnected, or a discharged battery is
recharged.
In this case, initialize and reset the
system by doing the following steps
from 6 to 10.
The open power sliding door warning
light stays on though the sliding door
is closed.
In this case, initialize and reset the
system by doing the following steps
from 1 to 10.
CAUTION
To initialize and reset power sliding
door system, stop the vehicle on a
level ground.
1. Be sure to turn off the power sliding
door system by pushing in the “PWR
DOOR OFF” switch.
2. Disconnect the battery for 1 minute
and then reconnect it.
3. Close the sliding door by hand.
(Step 3 can be performed before step
2.)
4. Turn on the power sliding door system
by pushing out the “PWR DOOR OFF”
switch.
5. Wait 5 seconds.
6. Open the sliding door by using one of
the “DOOR L”, “DOOR R” and “PWR
DOOR” switches.
7. Wait 3 seconds after the sliding door
stops at the fully–opened position.
8. Close the sliding door by using one of
the “DOOR L”, “DOOR R” and “PWR
DOOR” switches inside the vehicle or
“POWER DOOR”, “D–PWR DOOR” and
“P–PWR DOOR” switches of the wireless remote control transmitter.
9. Wait 3 seconds after the sliding door
stops at the fully–closed position.
10. Repeat the steps from 6 to 9.
2002 MY SIENNA_U (OM45407U)
23
If the power sliding door system does not
operate properly after the above procedure, there may be a problem in the system. Contact your Toyota dealer.
24
02 SIENNA_U (L/O 0107)
Wireless remote control
Locking operation
Unlocking operation
2002 MY SIENNA_U (OM45407U)
The wireless remote control system allows you to lock or unlock all the
doors from a distance within approximately 1 m (3 ft.) of the vehicle. On
some models, the system also allows
you to activate the theft deterrent system from the same distance.
LOCKING AND UNLOCKING THE
DOORS
To lock and unlock all the doors, push
the switches of the transmitter slowly
and securely.
To lock: Push the “LOCK” switch. All the
doors are locked simultaneously. At this
time one beep will be heard, parking
lights, side marker lights, tail lights and
other exterior lights will flash once.
Left and right side power sliding door
models—If the “LOCK” switch is kept
pressed in, the panic mode will work. (For
details, see “PANIC (LOCK)” SWITCH.)
Check to see that the doors are securely
locked.
If any of the doors is not securely closed,
or if the key is in the ignition switch,
locking cannot be performed by the
“LOCK” switch and a beep will sound continuously for 10 seconds. However, if the
key is in the ignition, a beep will not
sound.
02 SIENNA_U (L/O 0107)
To stop the beep, close all the doors securely or push the “UNLOCK” switch.
To unlock: Push the “UNLOCK” switch
once to unlock only the driver’s door.
Pushing the switch twice within 3 seconds
unlocks all the doors simultaneously. Each
time the “UNLOCK” switch is pushed, two
beeps will be heard, and the parking
lights, side marker lights and tail lights
will flash twice.
When the “UNLOCK” switch is pressed,
the personal lights, interior lights and/or
ignition key light come on. The lights remains on for about 15 seconds unless any
of the doors are opened then and closed.
(For further information, see “Personal
lights”, “Interior lights” and/or “Ignition
switch light” in Section 1–4.)
You have 30 seconds to open a door after
using the wireless remote unlock feature.
If a door is not opened by then, all the
doors will automatically lock again.
If the “LOCK” or “UNLOCK” switch is kept
pressed in, the locking or unlocking operation is not repeated. Release the button
and then push again.
SWITCHING BEEP SOUND ON AND OFF
You can switch the beep on and off. (The
beep is on initially and after battery replacement.)
To switch the beep on and off:
With the driver’s door opened—
1. Insert the ignition key and remove it.
2. Within 5 seconds, insert the ignition
key again and turn it to the “ON” position.
3. After 10 seconds, push the same
“LOCK”, “UNLOCK” or “PANIC” button
twice within 10 seconds.
Two beep sounds inform you that the
program has been switched on or off.
If this procedure is not followed exactly,
the beep will not operate as expected.
Check the beep ON/OFF operation by
pushing the wireless remote control transmitter switch after you finish this procedure. If the beep does not operate as
expected, repeat this procedure from step
1.
Right side power sliding door models
2002 MY SIENNA_U (OM45407U)
Left and right side power sliding door
models
25
02 SIENNA_U (L/O 0107)
OPENING AND CLOSING WITH “POWER
DOOR”, “D–PWR DOOR” AND “P–PWR
DOOR” SWITCHES (on some models)
Push the switch of the wireless remote
control transmitter slowly and securely.
The power sliding door opens and
closes completely.
Left side power sliding door—
To open: Push the “D–PWR DOOR”
switch.
To close: Push the “D–PWR DOOR”
switch again.
Right side power sliding door—
To open: Push the “P–PWR DOOR” switch
or “PWR DOOR” switch.
To close: Push the “P–PWR DOOR”
switch or “PWR DOOR” switch again.
Opening and closing can be performed by
the “POWER DOOR”, “D–PWR DOOR”
and “P–PWR DOOR” switches under the
following conditions only:
The sliding door is unlocked.
The power sliding door system is on.
(The “PWR DOOR OFF” switch is
pushed out.)
The ignition key is not in the “ON”
position.
Left and right side power sliding door
models—The left side power sliding door
does not operate when the fuel filler door
is opened.
“PANIC (LOCK)” SWITCH (left and right
side power sliding door models)
Pushing and holding the “PANIC
(LOCK)” switch blows the horn intermittently and flashes the headlights, tail
lights and other exterior lights.
The “PANIC (LOCK)” switch is used to
deter vehicle theft when you witness anyone attempting to break into or damage
your vehicle.
26
2002 MY SIENNA_U (OM45407U)
02 SIENNA_U (L/O 0107)
The alarm will last for one minute. To stop
alarm midway, do the following:
Push any of the switch on the wireless
remote control transmitter.
Lock or unlock either front doors or
back door with the key.
Turn the ignition key from the “LOCK”
to “ON” position.
The panic mode does not work when the
ignition key is in the “ON” position.
“PANIC” SWITCH (right side power
sliding door models)
Pushing the “PANIC” switch blows the
horn intermittently and flashes the
headlights, tail lights and other exterior
lights.
The “PANIC” switch is used to deter vehicle theft when you witness anyone attempting to break into or damage your
vehicle.
The alarm will last for one minute. To stop
alarm midway, do the following:
Push any of the switch on the wireless
remote control transmitter.
Lock or unlock either front doors or
back door with the key.
Turn the key from the “LOCK” to “ON”
position.
The panic mode does not work when the
key is in the “ON” position.
WIRELESS REMOTE CONTROL
TRANSMITTER
The wireless remote control transmitter is
an electronic component. Observe the following instructions in order not to cause
damage to the wireless remote control
transmitter.
Do not leave the wireless remote con-
trol transmitter on places where the
temperature becomes high such as on
the dashboard.
Do not disassemble it.
Avoid knocking it hard against other
objects or dropping it.
Avoid putting it in water.
2002 MY SIENNA_U (OM45407U)
27
02 SIENNA_U (L/O 0107)
You can use up to 4 wireless remote control transmitters for the same vehicle.
Contact your Toyota dealer for detailed
information.
If the wireless remote control transmitter
does not actuate the doors or alarm, or
operate from a normal distance:
Check for closeness to a radio trans-
mitter such as a radio station or an
airport which can interfere with normal
operation of the transmitter.
The battery may have been consumed.
Check the battery in the transmitter. To
replace the battery, see “REPLACING
TRANSMITTER BATTERY”.
If you lose your wireless remote control
transmitter, contact your Toyota dealer as
soon as possible to avoid the possibility
of theft, or an accident. (See “If you lose
your wireless remote control transmitter”
in Section 4.)
MODEL/FCC ID: GQ43VT14T
CAN: 1470102849
MADE IN U.S.A.
This complies with Part 15 of the FCC
rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful
interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
REPLACING TRANSMITTER BATTERY
For replacement, use a CR2032 lithium
battery or equivalent.
CAUTION
Special care should be taken that
small children do not swallow the removed transmitter battery or components.
NOTICE
When replacing the transmitter battery, be careful not to lose the components.
Replace only with the same or
equivalent type recommended by
the manufacturer.
Dispose of used batteries according
to the local laws.
Replace the transmitter battery by the following procedures:
28
2002 MY SIENNA_U (OM45407U)
02 SIENNA_U (L/O 0107)
1. Using a coin or equivalent, open the
transmitter case.
2. Remove the discharged transmitter battery.
NOTICE
Do not bend the terminals.
2002 MY SIENNA_U (OM45407U)
3. Put a new transmitter battery with positive (+) side up.
Close the transmitter case securely.
NOTICE
Make sure the positive side and
negative side of the transmitter battery should be faced correctly.
Do not replace the battery with wet
hands. Water may cause unexpected
rust.
Do not touch or move any components inside of the transmitter, or
it may interfere with proper operation.
29
Be careful not to bend the electrode
of the transmitter battery insertion
and that dust or oils do not adhere
to the transmitter case.
Close the transmitter case securely.
After replacing battery, check that the
transmitter operates properly. If the transmitter still does not operate properly, contact your Toyota dealer.
02 SIENNA_U (L/O 0107)
Power windows
30
The windows can be operated with the
switch on each front door.
The power windows work when the ignition
switch is in the “ON” position.
OPERATING THE DRIVER’S WINDOW
Use the switch on the driver’s door.
Normal operation: The window moves as
long as you hold the switch.
To open: Lightly push down the switch.
To close: Lightly pull up the switch.
2002 MY SIENNA_U (OM45407U)
Automatic operation: Push the switch
completely down or pull it completely up,
and then release it. The window will fully
open or close. To stop the window partway, lightly move the switch in the opposite direction and then release it.
Jam protection function: During automatic closing operation, the window stops and
opens half way if something gets caught
between the window and window frame.
If the window receives a strong impact,
this function may work even if nothing is
caught.
Loading...