Toyota Prius 2012 User Manual
Rostra Precision Controls, Inc. - 2519 Dana Dr. - Laurinburg, NC 28352 - 800-782-3379 - rostra.com
SoftTouch Navigation System
250-7613 2012-2013 Toyota Camry Installation Instructions
General Applicability:
Toyota – 2012-2013 Prius/Prius V, 2013 Venza, 2013 Avalon, 2013 Highlander, 2013 Tacoma
For video installation instructions, please visit us online at www.rostra.com.
Parts Identification
Page 1
Vehicle Preparation
Page 3
Programming Switch Settings
Page 3
Installation
Page 4
Parts Identification
Item
Qty.
Description
1 1 Navigation interface module
2 1 LCD IN harness
3 1 TP-IN harness
4 1 Hardware service parts (VHB tape, metal plate)
5 1 Vehicle interface harnesses
6 1 Stylus
7 1 GPS antenna with magnetic base
8 1 GPS speaker
9 1 Navigation interface board
10 1 LCD-IN/TP-IN Extension Harness
Form #5420, 3-20-2013
Rostra Precision Controls, Inc. - 2519 Dana Dr. - Laurinburg, NC 28352 - 800-782-3379 - rostra.com
STOP
YOU MUST READ THESE WARNINGS AND NOTICE BEFORE PRODUCT
HANDLING AND INSTALLATION!
PRODUCT AND VEHICLE APPLICATION WARRANTY DISCLAIMER
WARNING ! The Navigation Electronic Components are sensitive to ElectroStatic Discharge (ESD). DO NOT HANDLE THE NAVIGATION ELECTRONIC
COMPONENTS WITHOUT PROPER ESD GROUNDING DURING
INSTALLATION. FAILURE TO USE PROPER ESD PROTECTION WHEN
HANDLING THE NAVIGATION COMPONENTS WILL VOID THE PRODUCT
WARRANTY.
WARNING ! Installation of this Navigation Electronics product in the vehicle
radio head unit must be performed by a professional technician that is experienced
with proper work methods, ESD handling requirements, and knowledgeable of
specific procedures for radio disassembly, Navigation Electronics installation, and
re-assembly of the vehicle Radio Head Unit as well as proper handling
requirements of all components involved. FAILURE TO FOLLOW PROPER
DISASSEMBLY, INSTALLATION, AND REASSEMBLY PROCEDURES AND
PROPER COMPONENT HANDLING REQUIREMENTS MAY RESULT IN
IRREVERSIBLE DAMAGE TO THE VEHICLE RADIO HEAD UNIT AND/OR
THE NAVIGATION ELECTRONICS AND WILL VOID THE PRODUCT
WARRANTY!
WARRANTY DISCLAIMER NOTICE! Radio removal, disassembly, installation
of Navigation Electronics, and Radio re-assembly / re-installation is the
responsibility of the installer, not Rostra Precision Controls, Inc. It is recommended
that you contract a professional installer that is experienced with proper work
methods involving electronics and knowledgeable of specific procedures for radio
disassembly, Navigation Electronics installation, and re-assembly / re-installation of
the Radio Head Unit in the vehicle. INSTALLATION DAMAGE TO THE
VEHICLE RADIO HEAD UNIT IS NOT THE RESPONSIBILITY OF ROSTRA
PRECISION CONTROLS, INC. AND IS EXPRESSLY NOT COVERED UNDER
THE PRODUCT WARRANTY.
Rostra Precision Controls, Inc. 2/5/2013
Rostra Precision Controls, Inc. - 2519 Dana Dr. - Laurinburg, NC 28352 - 800-782-3379 - rostra.com
WARNING
To avoid dangerous distractions that may lead to an accident, the driver should never operate
the system while the vehicle is in motion. Before installing this product, the seller should
inform the end-user of proper use and compliance with the proper instructions and all state and
federal laws.
Vehicle Preparation
Before beginning your installation, familiarize yourself with the installation instructions and the
SoftTouch Navigation system components.
To ensure your safety, (A) apply the emergency brake and (B) read this entire manual before
beginning.
CAUTION: It is advisable to disconnect the negative battery cable for 3 minutes before
beginning installation, to avoid unintended air bag deployment. Note and record any anti- theft
radio codes prior to disconnecting.
Default Programming Switch (Dip Switch) Settings
Default Programming Switch Settings
1 – Off 2 – Off 3 – Off 4 – Off 5 – Off 6 – Off 7 – Off 8 – Off
Factory or Aftermarket Camera Settings
To use an aftermarket camera – Place switch #1 in OFF position.
To use the vehicle’s factory camera – Place switch #1 in ON position.
Visit www.rostra.com to view all compatible backup cameras!
Loading...