Toyota Prius 2004 Owner's Manual
SECTION 1– 1
FEATURES ON NEW TOYOTA VEHICLE
Overview of instruments and controls
Instrument panel overview 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument cluster and multi−i n formation di splay overview 4. . . . . . . .
Indicator symbols on the instrument p anel and multi−information
display 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
Instrument panel overview
11p003d
1. Side vents 187. . . . . . . . . . . . . . . . . . . . . . .
2. Side defroster outlets
3. Instrument cluster 4. . . . . . . . . . . . . . . . . .
4. Center vents 187. . . . . . . . . . . . . . . . . . . . .
5. Glove boxes 191. . . . . . . . . . . . . . . . . . . . .
6. Power door lock switches 38. . . . . . . . .
7. Power window switches 40. . . . . . . . . . .
8. Auxiliary boxes 195. . . . . . . . . . . . . . . . . . .
9. Cup holders 196. . . . . . . . . . . . . . . . . . . . .
10. Tilt steering lock release lever 96. . . . .
11. Hood lock release lever 43. . . . . . . . . . .
12. Parking brake pedal 141. . . . . . . . . . . . . .
13. Power rear view mirror
control switch 97. . . . . . . . . . . . . . . . . . . . .
14. Window lock switch 41. . . . . . . . . . . . . . .
2
11p001h
1. Headlight and turn signal
swit ches 102. . . . . . . . . . . . . . . . . . . . . . . . .
2. Wiper and washer switches 109. . . . . . .
3. “POWER” switch 130. . . . . . . . . . . . . . . . .
4. Clock 190. . . . . . . . . . . . . . . . . . . . . . . . . . . .
5. Multi−information display 146. . . . . . . . . .
6. Emergency flasher switch 106. . . . . . . . .
7. Trip meter reset button 115. . . . . . . . . . .
8. Km/h or MPH button 116. . . . . . . . . . . . .
9. Car audio 156. . . . . . . . . . . . . . . . . . . . . . . .
10. Power outlet 190. . . . . . . . . . . . . . . . . . . . .
11. “P” position switch 135. . . . . . . . . . . . . . .
12. Electronic shift lever
(R, N, D, B) 135. . . . . . . . . . . . . . . . . . . . .
13. Key slot 19. . . . . . . . . . . . . . . . . . . . . . . . . .
14. Cruise control switch 141. . . . . . . . . . . . .
15. Smart entry and start system
cancel switch 32. . . . . . . . . . . . . . . . . . . . .
16. Climate remote control
swit ches 186. . . . . . . . . . . . . . . . . . . . . . . . .
17. Instrument panel light control
dial 107. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18. Audio remote control switches 174. . . .
3
Instrument cluster and multi−information display overview
11p002i
1. Service reminder indicators
and indicator lights 117, 124. . . . . . . . . .
2. Fuel gauge 114. . . . . . . . . . . . . . . . . . . . . .
3. Speedometer
4. Odometer and trip meter 115. . . . . . . . .
4
Indicator symbols on the instrument cluster and Multi−information display
and
(U.S.A)
(Canada)
or
∗
Brake system warning lights
Driver’s seat belt reminder light
1
∗
1
Front passenger’s seat belt reminder light
∗
Low fuel level indicator light
Malfunction indicator lamp
∗
Master warning light
1
Open door warning light
1
∗
1
∗
1
∗
or
Anti−lock brake system warning light
∗
SRS warning light
1
Engine oil replacement reminder light
1
∗
1
(for vehicles sold in U.S.A.)
∗
1
Vehicle stability control system warning light
∗
Discharge warning light
2
High coolant temperature warning light
Low engine oil pressure warning light
∗
Hybrid vehicle battery warning light
2
Electric power steering system warning light
∗
1
∗
2
∗
2
∗
2
5
Automatic head light leveling system
warning light
Hybrid system warning light
Cruise control indicator light
∗
2
∗
2
∗
3
Automatic air conditioner indicator light
Recirculate mode indicator light
Windshield air flow indicator light
∗
Shift position indicator light
4
Smart entry and start system warning light
Turn signal indicator lights
Headlight high beam indicator light
Headlight indicator light
∗
5
∗
1
: For details, see “Service reminder indicators and warning
Rear window and outside rear view mirror defoggers indicator light
Low temperature indicator light
Hybrid vehicle immobilizer / Theft deterrent system indicator light
Slip indicator light
buzzers— —Instrument cluster” on page 117.
∗
2
Tail light indicator light
Driving ready light
: For details, see “Service reminder indicators and warning
buzzers— —Multi−information display” on page 124.
∗
3
: If this light flashes, see “Cruise control” on page 141.
∗
4
: For details, see “Hybrid transaxle” on page 135.
∗
5
: For details, see “Smart entry and start system” on page 23.
6
SECTION 1– 2
FEATURES ON NEW TOYOTA VEHICLE
Toyota hybrid system
Toyota hybrid systemm 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Toyota hybrid system operating condition 8. . . . . . . . . . . . . . . . . . . . . . .
Starting your vehicle 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
For efficient use of your vehi cle 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Precautions for use 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
Toyota hybrid system
Toyota hybrid system combines a gasoline engine and electric motor power to
improve the fuel economy and minimize
the emissions as well as to provide
better power performance than the ordinary gasoline−powered vehicles.
Depending on the driving condition, the
vehicle runs on the best combination of;
D Gasoline engine power
D Electric motor power generated by
the gasoline engine
D Electric motor power of the hybrid
vehicle battery
Furthermore, the energy is efficiently used
in the following ways:
D When stopping the vehicle, the gaso-
line engine is automatically stopped.
D When applying the brakes or decelerat-
ing, electricity is converted from the
turning force of the wheels and stored
in the hybrid vehicle battery. (This is
called regenerative brake.)
Since the battery is charged by the
gasoline engine as needed, it does not
require charging from an outside
source like an electric vehicle.
If you do not use the vehicle for a
long time (2 weeks or more), the hy-
brid vehicle battery and auxiliary battery
will discharge and their condition is liable to decline. Therefore, in order to
make up for discharging, charge them
once in every 2 weeks for about 30
minutes by starting the hybrid system
with all electrical components turned off.
Toyota hybrid system
operating condition
Basic operations are described below. Besides, Toyota hybrid system performs various controls depending on the operating
condition: The “Energy Monitor” screen
tells you which power is used currently.
8
12p016c
12p017c
12p018c
Electric power
in use
When starting or backing up, etc., the
vehicle runs on electric power from hybrid
vehicle battery, because the gasoline engine efficiency is low.
Gasoline power
in use
During normal driving, the vehicle runs
mainly on gasoline power. However, the
electric motor, using electric power generated by the gasoline engine, can supplement the gasoline engine power.
The vehicle controls the optimum ratio of
the gasoline and electric power to help
use energy more efficiently.
Electric and gasoline
power in use
When driving at full throttle, additional
electric power is applied from the hybrid
vehicle battery. Vehicle performance improves.
9
12p019c
12p020c
12p030b
Storing electric power
When decreasing speed or applying the
brakes, the turning force of the wheels
makes the electric motor operate as a
generator and additional electricity is
stored in the hybrid vehicle battery (regenerative brake).
10
Not in use
When stopping, the gasoline engine automatically shuts off.
Charging hybrid vehicle battery
When the hybrid vehicle battery power is
insufficient, the gasoline engine charges
the hybrid vehicle battery. The system always supplies electricity at a constant level.
Starting your vehicle
Your vehicle is equipped with push button start. The hybrid system will start
automatically by pressing the “POWER”
switch briefly with the brake pedal depressed.
Without smart function
1. Insert the key.
2. Press the “POWER” switch briefly with
the brake pedal depressed.
With smart function
1. Carry the key with you.
2. Press the “POWER” switch briefly with
the brake pedal depressed.
The “READY” light flashes and stays on.
A beep sounds after a few seconds, and
the hybrid system will start. (If the ambient temperature is low such as during
winter, it may take time until the “READY”
light comes on.) You cannot start your
vehicle when the brake pedal is not depressed. (For details, see “How to start
the hybrid system—” on page 230.)
The engine may not start even with the
“READY” light on.
For efficient use of your
vehicle
Drive your vehicle with a smooth acceleration and deceleration.
D While driving, energy is recovered
through the regenerative brake as the
vehicle decelerates. However, for more
efficient use, do not accelerate or decelerate your vehicle more than necessary.
D Avoid abrupt acceleration and decelera-
tion.
D The remaining capacity of the hybrid
vehicle battery can be confirmed on
the energy monitor screen of the multi−
information display. See “Information”
on page 150 for details. Gradual or
non−abrupt acceleration or deceleration
will more effectively use the benefits of
an electric motor without having to use
gasoline engine power.
When parking, be sure to put the hybrid transaxle in “P”. While driving, use
the hybrid transaxle in “D”.
D In “N”, the gasoline engine operates
but electricity cannot be generated. The
battery will be discharged requiring unnecessary engine power to recharge.
D The hybrid system automatically re-
charges the hybrid vehicle battery
when the remaining battery power is
reduced. However, the charging is not
available if the hybrid transaxle is “N”.
11
INFORMATION:
The gasoline engine starts and stops
automatically. (It stops during a low
load driving, deceleration or when the
vehicle is stopped.)
If the “READY” light remains on, you
can start your vehicle using the electric
motor even with the gasoline engine
stopped.
The gasoline engine may not stop automatically in the following conditions:
z During gasoline engine warm−up
z During hybrid vehicle battery charg-
ing
z During low or high hybrid vehicle
battery temperature
Precautions for use
The vehicle runs in combination with
the gasoline and electric power. Pay
special attention to the following items.
Be careful of high voltage and high
temperat ure.
Your vehicle is equipped with the orange
colored cables connected to the hybrid
vehicle battery (about 200 V) and to other
components that are all high voltage.
CAUTION
Do not touch or come in contact with
orange cables or battery terminals.
Electric shock may cause serious injury or death. Read all caution labels.
An electric motor, coolant radiator and
some other parts reach high temperature
while driving. Caution labels are applied to
these parts. Carefully observe the instructions on these caution labels.
Hybrid vehicle battery
Service
plug
High voltage
cables
Do not touch the service plug.
The service plug is installed in the left
side trim of the luggage compartment. It
is provided to disable high voltage current
from the hybrid vehicle battery when the
vehicle is in need of repairs at a Toyota
dealer.
12p007d
Air conditioning
compressor
High voltage cables
Inverter unit
CAUTION
12
CAUTION
Never remove or disassemble any
high voltage part, high voltage cables
(orange color) and their connectors.
It may cause death or serious injury.
D The shaded parts in the illustration
are subjected to high voltage.
D Inappropriate handling may cause
an electric shock resulting in serious injury or death. Never touch
any item in shaded area.
These high voltage parts or cables
consisting of an electromagnetic
shielding structure produce relatively
the same amount of electromagnetic
waves as conventional gasoline−
fueled vehicles or home electric appliances.
As unwanted noise may occur in the
reception of mobile radios, contact
your Toyota dealer for installation or
removal.
Always keep your hybrid vehicle’s driving characteristics in mind.
CAUTION
The driver should pay full attention
around the vehicle especially when it
is driven only by the electric motor
(with the gasoline engine stopped).
People in the immediate area might
misjudge the hybrid vehicle movement based on the absence of the
regular engine noise.
D When the hybrid system is started or
stopped, you may hear a sound coming
from the hybrid vehicle battery in the
luggage compartment. However, this
does not indicate any trouble.
D As the vehicle runs with both the gaso-
line engine and electric motor, you may
hear a motor sound coming from the
engine compartment.
D If the “READY” light is on, you can
start even though the gasoline engine
may be off.
D When you shift the shift lever to “B”
and release it to its original position
and your foot from the accelerator pedal, engine braking will be applied. However, during high speed driving you
may feel that deceleration by engine
braking is less than that of ordinary
vehic le.
Be sure to put the hybrid transaxle in
“P” when parking.
In “N”, the hybrid vehicle battery assembly
is not charged, even if the gasoline engine is operating. You cannot run your
vehicle if the hybrid transaxle is left in “N”
for a long time because the hybrid vehicle
battery assembly will be discharged.
When you leave your vehicle, apply the
parking brake to put the hybrid transaxle in “P” and be sure to carry the
key with you and lock all the doors.
If you leave the hybrid system in “ACC”
or “IG−ON”, the hybrid system may not
start because the auxiliary battery will be
disc harged.
CAUTION
D When you leave your vehicle, be
sure to shut off the hybrid system.
D Be sure to put the hybrid transaxle
in “P” because the vehicle can start
with the “READY” light on and the
engine stopped (no engine sound
and vibration). When the “READY”
light is on, if you leave your vehicle in shift position other than
“P” and “N”, the vehicle will creep
and start abruptly with the accelerator pedal being depressed by mistake. This may cause death or serious injury.
13
12p008d
When the multi−information display
shows this message, the master warn-
ing light
ment cluster. Read the message and
follow the instruction.
D When you leave your vehicle, or stop
D Charging is necessary. In “N”, charging
( ) comes on in the instru-
or park for a while, put the hybrid
transaxle in “P”.
will not be applied. The electric generator operates in “P”, “D” or “B”. If you
continue driving, put the hybrid transaxle in “D” or “B” and depress the
accelerator pedal. Do not leave the hybrid transaxle in “N”. When driving in
traffic jam, operate in “D”.
12P009c
Do not allow anyone to lean against the
side of the rear right seatback, nor put
any luggage or other obstructions on it.
D An air vent is provided on the side of
the rear right seatback to cool the hybrid vehicle battery. If this vent is covered, the hybrid vehicle battery will
overheat resulting in a reduction of the
output performance of the hybrid system.
D The seat belt not properly set in the
guide on the top of the rear seat may
block the air vent. Be sure to pass the
seat belt through the guide properly.
D Do not wet or put foreign objects over
the air vent. Otherwise, the hybrid vehicle battery may be adversely affected
and be damaged.
D You may hear a cooling fan noise from
the air vent.
For vehicle repairs or maintenance, be
sure to consult your Toyota dealer.
If your vehicle is beyond repair because
of accident or something, be sure to
consult your Toyota dealer.
As sealed Nickel−Metal hydride batteries
are used, be sure to consult your Toyota
dealer when disposing of your vehicle.
14
CAUTION
If you are involved in an accident,
follow these precautions.
D Move the vehicle to a safe place
and perform the followings to reduce the risk of high voltage electricity leakage.
D Depress the brake pedal and apply
the parking brake.
D Press the “P” position switch and
stop the hybrid system.
D If the key is inserted into key slot,
remove it.
D If your vehicle has experienced ma-
jor damage, you may get an electric
shock. To prevent this, never touch
the high voltage parts (hybrid vehicle battery assembly, etc.) or
cables (orange color) connecting
these parts. If some exposed electric wires are protruding inside or
outside of the vehicle, an electric
shock may also occur. Never touch
them.
D If the fluid leaks or gets in some
part of the vehicle, never touch it
because it may be electrolyte
(strong alkali) from the hybrid vehicle battery. If it gets on your skin
or eyes, wash off immediately with
a large amount of water, if possible,
with boric acid solution, and get
immediate medical attention in order to help avoid serious injury.
D If a vehicle fire occurs, extinguish
it using a fire extinguisher for the
exclusive use on electric fires. As
a small amount of water may be
dangerous, use a large amount of
water, for example from a fire hydrant, or wait for a fire−fighting
team arrival.
D If your vehicle needs to be towed,
do it with the front wheels or all
four wheels raised. If the front
wheels are on the ground when
towing, the electric motor may continue to generate electricity which
could leak electricity. A fire could
occur depending on the degree of
damage. See “If your vehicle needs
to be towed” on page 254.
15
16
SECTION 2– 1
OPERATION OF INSTRUM ENTS AND
CONTROLS
Keys and Doors
Keys 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hybrid vehicle immobilizer system 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Smart entry and start system 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wireless remote control 33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Side doors 37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Back door 39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power windows 40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hood 43. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Theft deterrent system 44. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel tank cap 46. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17
Keys—
21p001a
1. Master keys with silver ornament (Ve-
hicles equipped with smart entry and
start system)—These keys work in every lock. Your Toyota dealer will need
one of them to make a new key with
a built−in transponder chip. Before you
use these keys, be sure to read “Smart
entry and start system” on page 23.
2. Master keys without silver ornament
(Vehicles not equipped with smart entry
and start system)—These keys work in
every lock. Your Toyota dealer will
need one of them to make a new key
with a built−in transponder chip.
3. Mechanical keys (attached to the mas-
ter key)—These key work for the driver’s door only.
18
21P112
USING A MECHANICAL KEY
When you use the mechanical key included on the side of the key, slide the
lock knob in the arrow direction and take
out the key as shown. To put the key
back, slide the lock knob in the arrow
direction and replace the key. Be sure to
put the key back when not in use.
Since the doors can be locked without a
key, you should always carry a spare
master key in case you accidentally lock
your keys inside the vehicle.
NOTICE
When using a key containing a transponder chip, observe the following
precautions:
z Do not affix any material that cuts
off electromagnetic waves (such as
a metal seal) on the key.
z Do not knock the key hard against
other objects.
z Do not leave the key exposed to
high temperatures for a long period,
such as on the dashboard or hood
under direct sunlight.
z Do not put the key in water or
wash it in an ultrasonic washer.
z Do not keep the key together with
the products emitting electromagnetic waves such as a cellular
phone.
—Key slot
21p006a
Your vehicle keys and the key slot are
different shapes from conventional ones.
Keep the following in mind when operating
the key:
D When inserting the key, be sure to
push it in all the way.
D When pulling out the key, be careful
because it will be pushed out by the
spring and it might fly out.
D If the key cannot be pulled out, push
it in all the way again, then pull it out.
CAUTION
Do not put your finger into the key
slot. Your finger might be injured.
NOTICE
Observe the following instructions, or
the key mechanism might be damaged
and will not work properly.
z The key should be operated with a
clean hand and fingers.
z Do not insert the key forcibly.
z Do not insert any key other than
genuine formal keys into the key
slot.
z Do not pull out the key forcibly
when it cannot be removed.
z Do not put water, oil, foreign ob-
jects, etc. into the key slot.
z Do not insert a wet, oily or dam-
aged key into the key slot.
z Do not affix a sticker on the key.
z Do not insert the key in the wrong
way.
z Do not pull out the key ring when
removing the key out of the key
slot.
Should you find anything unusual,
contact your Toyota dealer as soon as
possible.
19
Hybrid vehicle immobilizer
system
21p005a
KEY NUMBER PLATE
Your key number is shown on the plate.
Keep the plate in a safe place such as
your wallet, not in the vehicle.
If you should lose your keys or if you
need additional keys, duplicates can be
made by a Toyota dealer using the key
number.
We recommend writing down the key number and storing it in a safe place.
20
21p006a
DEACTIVATION USING THE KEY
The hybrid vehicle immobilizer system
is a theft prevention system. When you
insert the key in the key slot, the transponder chip in the key transmits an
electronic code to the vehicle. The hybrid system will start only when the
electronic code in the chip corresponds
to the registered ID code for the vehicle.
21p007b
The system is automatically set when the
key is removed from the key slot. The
indicator light will start flashing to show
the system is set.
If any of the following indicator conditions
occurs, contact your Toyota dealer.
D The indicator light stays on except
when the theft deterrent system is setting or activating. (See “Theft deterrent
system” on page 44.)
D The indicator light does not start flash-
ing when the key is removed from the
key slot.
D The indicator light flashes inconsistent-
ly.
Inserting the registered key in the key slot
automatically cancels the system, which
enables the hybrid system to start. The
indicator light will go off.
For your Toyota dealer to make you a
new key with built−in transponder chip,
your dealer will need your key number
and master key. However, there is a limit
to the number of additional keys your
Toyota dealer can make for you.
NOTICE
Do not modify, remove or disassemble the hybrid vehicle immobilizer
system. If any unauthorized changes
or modifications are made, proper operation of the system cannot be guaranteed.
21p113
DEACTIVATION USING THE SMART
FUNCTION
The hybrid vehicle immobilizer system
is a shift prevention system. When you
enter the vehicle carrying a smart key
and press the “POWER” switch, the
electronic code in the key is automatically checked to determine whether it
corresponds to the registered ID code
for the vehicle. If the ID code is verified, you can start the hybrid system.
21p007b
The system is automatically set when the
hybrid system is off and driver’s door is
opened. The indicator light will start flashing to show the system is set.
If any of the following indicator conditions
occurs, contact your Toyota dealer.
D The indicator light stays on except
when the theft deterrent system is setting or activating. (See “Theft deterrent
system” on page 44.)
D The indicator light does not start flash-
ing when the hybrid system is off and
driver’s door is opened.
D The indicator light flashes inconsistent-
ly.
21
Carrying a smart key and pressing the
“POWER” switch automatically cancels the
system, which enables the hybrid system
to start. The indicator light will go off.
For your Toyota dealer to make you a
new key with built−in transponder chip,
your dealer will need your key number
and master key. However, there is a limit
to the number of additional keys your
Toyota dealer can make for you.
NOTICE
Do not modify, remove or disassemble the hybrid vehicle immobilizer
system. If any unauthorized changes
or modifications are made, proper operation of the system cannot be guaranteed.
For vehicles sold in U.S.A.
FCC ID: MOZRI−24KTY
MADE IN JAPAN
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
CAUTION
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
For vehicles sold in Canada
This device complies with RSS−210 of
industry Canada. Operation is subject to
the following two conditions:
(1) This device may not cause interference, and (2) this device must accept
any interference, including interference
that may cause undesired operation of
the device.
22
Smart entry and start system
21p120
1. Locking and unlocking
2. Starting the hybrid system
By carrying a smart key, you can lock
and unlock the doors and start the hybrid system.
For locking the doors, see “Locking the
doors with smart function” on page 28.
For unlocking the doors, see “Unlocking
the door(s) with smart function” on page
29. For starting the hybrid system, see
“Push button start” on page 130.
If the smart key battery is discharged, the
smart function cannot be used. Use the
mechanical key attached to the smart key
by inserting it in the driver’s door keyhole
to lock or unlock door. To start the hybrid
system, insert the smart key into the key
slot. In order to activate the smart function, the battery should be replaced. For
details, see “REPLACING THE BATTERY”
on page 36.
You can deactivate the smart function by
using the cancel switch. In this case, all
the smart function will be deactivated. For
details, see “Deactivating the smart function” on page 32.
INFORMATION
D Be sure to take the smart key with
you.
D In the following cases, the smart
function or wireless remote control
feature may not operate properly. (If
this happens, use a mechanical key
to lock or unlock the driver’s door
and a smart key to start the hybrid
system.)
z When facilities issuing strong
electromagnetic waves such as
TV towers, electric power stations, broadcasting stations are
nearby.
z When you are carrying a smart
key together with a mobile communications system such as a
two−way radio or cellular phone.
z When the smart key is in contact
with or covered by a metallic object.
z When another person is operating
a wireless remote control function on another vehicle near your
vehicle.
23
If you do not drive your vehicle,
D
store the smart key, keeping it at
least 5 m (16 ft.) away from the vehicle.
ALARMS AND WARNING LIGHT
Your vehicle is equipped with alarms
inside and outside, as well as warning
light in the instrument cluster, that remind you if there is a problem involving the smart entry and start system.
This warning light will come on when the
“IG−ON” mode is enabled and will go off
after a few seconds.
If an alarm sounds or the warning light
comes on, be sure to check your vehicle and smart key.
(a) The hybrid system was not turned
off and the transaxle was in a position other than “P”.
When the driver’s door is opened with the
hybrid system in “ACC” or “IG−ON” and
with the transaxle in a position other than
“P”.
Inside alarm: Beeps continuously
Multi−information display: Warning mes-
sage
Alarms will be turned off by any of the
following operations:
D Closing the driver’s door
D Pressing the “P” position switch
D Turning on the hybrid system
D Turning off the hybrid system
24
(b) The smart key was brought outside
the vehicle with the transaxle in a
position other than “P”.
When the driver’s door is opened or
closed with the hybrid system not to be
turned off and with the transaxle in a
position other than “P”, it is determined
that the smart key is not in the vehicle.
Inside alarm: Beeps continuously
Outside alarm: Beeps continuously
Warning light: On
Alarms will be turned off by any of the
following operations:
D Pressing the “P” position switch
D Bringing the smart key inside the ve-
hicle
D Turning off the hybrid system
(c) The hybrid system was not turned
off with the transaxle in “P”.
When the driver’s door is opened with the
hybrid system in “ACC” and with the
transaxle in “P”.
Inside alarm: 3 Beeps
In the “IG−ON” mode, an alarm will not
sound.
(d) The smart key was brought outside
the vehicle.
When the driver’s door is opened or
closed with the hybrid system not to be
turned off (and with the transaxle in “P”),
it is determined that the smart key is not
in the vehicle.
Inside alarm: One beep
Outside alarm: 3 beeps
Warning light: On
(e) Locking with smart function was at-
tempted with the hybrid system not
to be turned off.
When you attempt to lock all the doors
using smart locking function with the hybrid system not to be turned off and with
the transaxle in a position other than “P”.
Outside alarm: One beep (sounds for 2
seconds.)
Warning light: On
At this time, the doors cannot be
locked.
(f) The smart key was brought outside
the vehicle.
When a door other than the driver’s door
is opened or closed with the hybrid system not to be turned off, it is determined
that the smart key is not in the vehicle.
Inside alarm: One beep
Outside alarm: 3 beeps
Warning light: On
25
(g) Preventing the key from being
locked inside the vehicle
When you close the door with the hybrid
system off but with the smart key left in
the vehicle, and attempt to lock all the
doors using smart locking function, it is
determined that the smart key is in the
vehic le.
Outside alarm: One beep (sounds for 2
seconds)
INFORMATION
z This function may not operate when
the smart key is left on the instrument panel, luggage cover, floor or
in the glove box.
z The function may operate if the
smart key is brought outside but it
is very close to the door window or
door handle.
(h) Low smart key battery
When the hybrid system is turned to
“ACC” or “OFF” about 20 minutes after
the hybrid system is turned on or to “IG−
ON”, it is determined that the smart key
battery voltage is low.
Inside alarm: One beep
(i) Outside of effective range
When the “POWER” switch is pressed, it
is determined that the smart key is not in
the vehicle.
Inside alarm: One beep
Warning light: On (for 5 seconds)
(j) Open door warning
When you attempt to lock all the doors
using smart locking function with the hybrid system turned off but with any door
open.
Outside alarm: One beep (sounds for 10
seconds)
Alarms will be turned off by either of
the following operations:
D Closing all the doors
D Pressing the “ ” (unlock) button on
the smart key
26
Warning and its meaning
Inside warning alarm
Outside warning alarm Warning light Causes
One beep
(sounds cont i nuous ly)
One beep
(sounds cont i nuous ly)
Beeps
(sound intermittently)
One beep 3 beeps On
—
One beep 3 beeps On
—
One beep — — The key battery voltage become about 2 V. (3 V for normal operation)
One beep —
—
(sounds cont i nuous ly)
(sounds f or 2 s econds)
(sounds f or 2 s econds)
(sounds for 10 seconds )
— —
One beep
— —
One beep
One beep
One beep
On
On
—
On
(for 5 sec onds)
—
The driver’s door was opened when the hybrid system was in “ACC”
or “IG−ON” and when the transaxle was in a position other than “P”.
The driver brought out the smart key from the vehicle with the hybrid
system not to be turne d off and with the transaxle in a position other
than “P”.
The driver’s door was opened when the hybrid system was in “ACC”
and when the transaxle was in “P”.
The driver brought out the smart key from the vehicle with the hybrid
system not to be turned off and with the transaxle in “P”.
The l ock switch w as pressed with the hyb rid system not to b e turned
off and with the transaxle in “P”.
The passenger brought o ut t he smar t key f rom the vehi cl e wi th the
hybrid system not to be turned off.
The lock sw itch was presse d whe n the hybrid system was o ff but with
the smart key left in the vehicle.
The “POWER” switch was pressed when the smart key was not in the
effective range of the system.
The lock switch was pressed w h e n the hybrid s ystem wa s off but a n y
door was opened.
27
Side door
21p128
21p139
LOCKING THE DOORS WITH SMART
FUNCTION
The smart entry and start system will
lock the doors without being inserted
into the door keyhole.
When you exit the vehicle carrying the
smart key and push the lock button on the
outside front door handle or back door
with all the doors closed, all the doors will
be locked provided that the electronic
code in the key corresponds to the registered ID code for the vehicle.
At this time, you will hear one beep and
the turn signal lights flash once. However,
when you push the lock button on the
outside front door handle or back door
with any door not closed securely, a beep
sounds for 10 seconds.
NOTICE
If the key is in the vehicle, do not
perform door locking operation, or
you might lock your keys inside the
vehicle.
INFORMATION
D The rear doors are not equipped
with smart function.
D When locking the doors, be sure to
push the lock button on the outside
front door handle or back door
slowly and surely. If you push the
button quickly, the doors may not
lock.
D When opening or closing a door, do
not touch the lock button on the
outside door handle or back door. If
you push the button, an alarm
sounds 10 seconds.
D When a wireless remote control is
used to lock the doors and a smart
key is left in the effective range of
the smart function in the vehicle,
the doors cannot be unlocked using
the smart function. In this case, use
the wireless remote function to unlock the doors.
D You cannot activate smart unlocking
functions within 3 seconds after the
smart locking function is activated.
Back door
28
21p136
UNLOCKING THE DOOR(S) WITH
SMART FUNCTION
The smart entry and start system can
be used to unlock the door(s) without
being inserted into the door keyhole.
When you get close to your vehicle (about
1 m (3 ft.) from each outside front door
handle), and are carrying the smart key,
the electronic code emitted from the key
is automatically checked to determine if it
corresponds to the registered ID code for
the vehicle. When you take hold of the
side back of the outside door handle surface, it will unlock. At this time, two
beeps sound and the turn signal lights
flash twice.
When you push and hold down the back
door opener switch, carrying the smart
key, the ID code is checked in the same
way as in the front door case. And all the
doors will unlock. At this time, two beeps
sound and the turn signal lights flash
twice.
When you get close to your vehicle (about
1 m or 3 ft. from either front door), carrying the smart key or unlock the back door
using smart key function, the interior light
comes on for 15 seconds if the interior
light switch is in the “DOOR” position.
However, the interior lights go out when
you push the power door lock switch in
the lock position or press the “POWER”
switch once or twice from the off setting
to select the “ACC” or “IG−ON” mode
without depressing the brake pedal. For
further information, see “Interior lights” on
page 107.
You have 30 seconds to open a door after
operating the smart unlocking function. If
a door is not opened by then, all the
doors will be automatically locked again.
INFORMATION
D The rear doors are not equipped
with smart function.
D When unlocking the door(s), be sure
to take hold of the back side of the
outside door handle firmly as
shown in the illustration. Taking
hold of the handle with a gloved
hand might cause a delay in unlocking.
29
When you take hold of the handle
D
or push the back door opener to
unlock the door(s), be sure to confirm that the door(s) have been unlocked. If the two beeps and the
turn signal lights flash twice, the
doors are unlocked. At this time,
you can pull the outside door handle or push the back door opener to
open the door. If you quickly move
closer to the vehicle or pull the outside door handle or push the back
door opener quickly, the doors
might not unlock. If you cannot
open the door by pulling the outside door handle or pushing the
back door at this time, push back
the outside door handle to the original position or release your hand
from the back door and then try
again.
D If you bring the smart key very
close to the outside door handle or
the back door opener, the doors
might not lock.
30
D If another person who is not carry-
ing a smart key takes hold of an
outside door handle or push the
back door opener when you are
within the effective range of the
smart function, the door(s) may not
unlock.
D If a large amount of water is ap-
plied to the outside door handle or
the back door during heavy rain or
a car wash, and someone carrying a
smart key is near the vehicle, the
door(s) might be unlocked. However,
if the outside front door handle is
not pulled out or back door opener
not pushed, the doors will lock automatically after about 30 seconds.
D To ensure the unlocking door(s),
perform unlocking operation within
3 seconds after getting close to the
vehicle (about 1 m or 3 ft. from the
front doors or back door). If it
takes longer than that, unlocking
function may not be enabled.
CHANGING THE DOORS TO BE UNLOCKED
Each time you push the “
ton together with the “
ton on the smart key for about 5 seconds with the hybrid system off, the
setting for door unlocking will change
as follows:
1. Driver’s door unlocking mode: If you
perform smart unlocking operation on
the driver’s door, it will unlock. Performing unlocking operation on the
front passenger’s door or back door
will unlock all the doors. When the
system switches to this mode, one
beep sounds inside the vehicle and two
beeps sound three times.
2. All doors unlocking mode: Performing
smart unlocking operation on either
front door or back door will unlock all
the doors. When the system switches
to this mode, one beep sounds inside
the vehicle and two beeps sound twice.
3. Single door unlocking mode: The
driver’s door or back door on which
you perform smart unlocking operation
will unlock. However, performing unlocking operation on the front passenger’s door will unlock all the doors.
When the system switches to this
mode, one beep sounds inside the vehicle and two beeps sound once.
” (lock) but-
” (panic) but-
Loading...