TOYOTA CR-LS7160 Service Manual
Specification*
I0
AUTOMOTIVE ELECTRONICS
CR-LS7160K
AM/FM MPX Electronic Tuning Radio
PART No. : 08600-12800
ID CODE : 72400
VEHICLE : COROLLA
DESTINATION : Brazil
PRODUCED AFTER : May, 2002
General
Power Supply DC 12V (11V - 16V),
Test Voltage 13.2V
Negative Ground
Current Consumption Less than 2.0A
Power Output 17W×4ch
AM Radio
Frequency Range 530 - 1,620kHz
Usable Sensitivity 25dB(µV) (S/N 20dB)
FM Stereo Radio
Frequency Range 87.9 - 108.0MHz
Usable Sensitivity 6dB/µV (S/N 30dB)
Dimensions** 178×70×165mm
Weight** 0.9kg
* Specifications and the design are subject to possible modification
without notice due to improvements.
** Dimensions and Weight shown are approximate.
CR-LS7160K
CONTENTS
Page Page
1 FEATUERS 2
2 REAR VIEW AND CONNECTORS
3 FRONT VIEW AND FUNCTIONS
4 BLOCK DIAGRAM
5 TERMINALS DESCRIPTION
6 PACKAGE AND IC BLOCK DIAGRAM
7 REPLACEMENT PARTS LIST 7
2
8 EXPLODED VIEW (Unit)
2
9 WIRING DIAGRAM
10 SCHEMAT IC DIAGRAM
3
4
11 MEMO
5
1 FEATUERS
11
12
15
17
∙
PLL (Phase Locked Loop) synthesized tuning.
∙
18-station preset (6-AM, 12-FM).
∙
Scan tuning function.
∙
Cassette tape player control.
∙
CD changer control.
∙
Electronic volume control.
2 REAR VIEW AND CONNECTORS
3 FRONT VIEW AND FUNCTIONS
2
4 BLOCK DIAGRAM
CR-LS7160K
3
CR-LS7160K
5 TERMINALS DESCRIPTION
5.1. Main Block
IC601 : C2CBHG000092
Pin
No.
1 BEEP Buzzer output O 0
2 ROM SCK Security ROM data shift clock O 0
3 ROM CS Security ROM chip select O 0
4 ROM ST Security ROM data O 0
5 ROM SO Security ROM data I 0
6 SEC ON Security timer on O 0
7 MUTE System mute O 0
8 SEC TIM Security timer I 4.3
9 NC No connection - 10 NC No connection - 11 RESET Reset input I 4.8
12 X2 Crystal oscillator terminal - 1.8
13 X1 Crystal oscillator terminal - 1.3
14 GND Ground - 0
15 X2 Crystal oscillator terminal - 1.7
16 X1 Crystal oscillator terminal - 1.4
17 REGOFF (Connecting to ground) - 0
18 REGCPU By pass capacitor terminal - 4.0
19 VDD0 +5V power supply - 5.0
20 FCONT2 Frequency control O 4.9
21 FCONT1 Frequency control O 0
22 SD B/S detection I 0
23 ST FM stereo detection I 0
24 PLL-DO PLL data input I 4.8
25 PLL-CLK Shift clock for PLL data O 0
26 PLL-DI PLL data output O 0
27 PLL-CE PLL chip enable O 0
28 NK ON/OFF Not used - 29 NC No connection - 30 NC No connection - 31 VOL-DATA Electronic volume data O 0
32 VOL-CLK Data shift clock O 0
33 LCD-CLK Data shift clock O 0
34 LCD-DO LCD data input I 4.8
35 NC No connection - 36 LCD-CE LCD chip enable O 0
37 LCD-DI LCD data output O 0
38 VOLA Volume SW contact A I 4.8
39 VOLB Volume SW contact B I 4.8
40 GND Ground - 0
41 VDD +5V power supply - 5.0
42 NC No connection - 43 MODEA Mode SW contact A I 0
44 MODEB Mode SW contact B I 0
45 NC No connection - 46 NC No connection - 47 NC No connection - 48 NC No connection - 49 NC No connection - 50 NC No connection - 51 SW/9Pro (Connecting to ground) - 0
52 9K/5K Radio tuning step selection I 5.0
53 NC No connection - 54 NC No connection - 55 NC No connection - 56 CLK Power control IC clock O 0
57 STBY Power control IC stand-by O 5.0
58 LATCH Power control IC data latch O 5.0
59 DATA Power control IC data O 0
60 NC No connection - -
Port Description I/O (V)
61 NC No connection - 62 NC No connection - 63 NC No connection - 64 MSOUT Not used - 65 NC No connection - 66 NC No connection - 67 NC No connection - 68 MS-PL/FF Not used - 69 T.LOAD Not used - 70 DOLBY Not used - 71 ILL PWM ILL PWM control O 4.5
72 LCD PWM LCD PWM control O 4.5
73 TEST (GND pull-down) - 0
74 REO IN Rheostat signal I 4.4
75 NC No connection - 76 NC No connection - 77 A/B Not used - 78 MTL Not used - 79 CAM A/B Not used - 80 MSM Not used - 81 NK-IN Not used - 82 VDD +5V power supply - 5.0
83 AVDD +5V power supply - 5.0
84 GND Ground - 0
85 LANIN LAN data input I 0
86 LANOUT LAN data output O 0
87 GND Ground - 0
88 NC (Connecting to ground) - 0
89 ILL-DET ILL detection I 0
90 EQ (Connecting to VDD) - 5.0
91 +B-DET Battery level detection I 4.9
92 ACC-DET ACC level detection I 4.9
93 TAPE-EJ (Connecting to VDD) - 5.0
94 T.IN (Connecting to VDD) - 5.0
95 END-B Not used - 96 END-A Not used - 97 NC No connection - 98 NC No connection - 99 NC No connection - -
100 NC No connection - -
Note 1 : Voltage measuerments are with respect to ground,
with a voltmeter (internal resistance : 10M ohms).
5.2. Display Block
IC601 : YEAMLC75853W
Pin
No.
1-33 SEG1-20 LCD segment data O 2.6
34-40 - Not used - 41-43 COM1-3 LCD common output O 2.6
44 S41 Not used - -
45-49 KS1-6 Key scan signal O 5.2
50 KI1 Not used - 0
51-54 KI2-5 Key data input I 0
55 TEST (Connecting to ground) - 0
56 VDD +5V power supply - 5.2
57 VDD1 Ground through capacitor - 3.5
58 VDD2 Ground through capacitor - 1.8
59 VSS Ground - 0
60 OSC CR oscillator - 4.1
61 DO key data output O 5.2
62 CE Chip enable I 0
63 CLK LCD clock I 0
64 DI LCD data input I 0
Port Description I/O (V)
4
6 PACKAGE AND IC BLOCK DIAGRAM
6.1. Main Block
CR-LS7160K
PA150 : YEP0PTA512B0
IC231 : AN7561Z-WLB
IC651 : YEAMH12187ER
5
CR-LS7160K
IC451 : YEAMLC72135C
IC201 : C1BB00000284
IC704 : AN8065SE1
IC701 : C0DBZHZ00006
IC602 : YEAM93LC46FE
6
Loading...