TOYOTA CQ-VS8180 Service Manual

Specifications*
CQ-VS8180A
AM/FM/SW MPX Electronic Tuning Radio with Stereo Cassette Tape Player
PART No. : 86120-42070 ID CODE : 57414
VEHICLE : COROLLA, PRONARD, ECHO, RAV4 DESTINATION : Middle and Near East PRODUCED AFTER : Aug., 2001
General Power Supply DC 12V (11V - 16V),
Test Voltage 13.2V
Negative Ground Current Consumption Less than 3.0A Power Output 20W×4
AM Radio Frequency Range 531 - 1,602 kHz Usable Sensitivity 25dB/µV (S/N 20dB)
FM Stereo Radio Frequency Range 87.5 - 108.0MHz Usable Sensitivity 6dB/µV (S/N 30dB)
SW Radio (SW1) Frequency Range 2.940 - 7.735MHz Usable Sensitivity 27dB/µV
SW Radio (SW2) Frequency Range 9.500 - 21.975MHz Usable Sensitivity 30dB/µV
Cassette Player Reproduction System 4-Track, 2-Program Stereo Tape Speed 4.76cm/sec. Wow and Flutter 0.09% (WRMS) Signal to Noise Ratio More than 42dB Separation More than 30dB
Dimensions** (W×H×D) 178×70×165mm Weight** 1.3kg
* Specifications and the design are subject to possible modification without notice due to improvements.
** Dimensions and Weight shown are approximate. Dolby noise reduction manufactured under license from Dolby
Laboratories Licensing Corporation. “Dolby” and the double-D symbol
Laboratories Licensing Corporation.
are trade marks of Dolby
CQ-VS8180A
CONTENTS
Page Page
1 FEATUERS 2 2 REAR VIEW AND CONNECTORS 3 FRONT VIEW AND FUNCTIONS 4 WIRING CONNECTION 5 BLOCK DIAGRAM 6 TERMINALS DESCRIPTION 7 PACKAGE AND IC BLOCK DIAGRAM 8 ALIGNMENT INSTRUCTIONS
9 ALIGNMENT POINTS 9
2
10 REPLACEM ENT PARTS LIST
3
11 EXPLODED VIEW (Unit) 12 TAPE PLAYER PARTS
4 5
13 EXPLODED VIEW (Tape Deck)
6
14 WIRING DIAGRAM 15 SCHEMAT IC DIAGRAM -1
7 9
16 SCHEMAT IC DIAGRAM -2
1 FEATUERS
10 14 15 17 18 23 25
PLL (Phase Locked Loop) synthesized tuning. 24-station preset (6-AM, 6-FM, 6-SW1, 6-SW2). Scan tuning function.
Dolby noise reduction. Electronic volume control. CD changer control function.
2 REAR VIEW AND CONNECTORS
2
3 FRONT VIEW AND FUNCTIONS
CQ-VS8180A
3
CQ-VS8180A
4 WIRING CONNECTION
4
5 BLOCK DIAGRAM
CQ-VS8180A
5
CQ-VS8180A
6 TERMINALS DESCRIPTION
6.1. Main Block
IC601 : C2CBHG000067
Pin No.
1 BEEP Buzzer output O 0 2 BIT3 Tape mode SW I 4.8 3 BIT2 Tape mode SW I 4.8 4 BIT1 Tape mode SW I 0 5 FIN Tape motor control O 0 6 RIN Tape motor control O 0 7 MUTE System mute O 0 8 NC No connection - -
9 NC No connection - ­10 NC No connection - ­11 RESET Reset input I 4.8 12 X2 Crystal oscillator terminal - 1.8 13 X1 Crystal oscillator terminal - 1.3 14 GND Ground - 0 15 X2 Crystal oscillator terminal - 1.7 16 X1 Crystal oscillator terminal - 1.4 17 REGOFF (Connecting to ground) - 0 18 REGCPU Not used - ­19 VDD0 +5V power supply - 5.0 20 FCONT2 Frequency control O 4.9 21 FCONT1 Frequency control O 0 22 SD B/S detection I 0 23 ST FM stereo detection I 0 24 PLL-DO PLL data input I 4.8 25 PLL-CLK Shift clock for PLL data O 0 26 PLL-DI PLL data output O 0 27 PLL-CE PLL chip enable O 0 28 NK ON/OFF AM noise cancellor on/off O 4.8 29 NC No connection - ­30 NC No connection - ­31 VOL-DATA Electronic volume data O 0 32 VOL-CLK Data shift clock O 0 33 LCD-CLK Data shift clock O 0 34 LCD-DO LCD data input I 4.8 35 NC No connection - ­36 LCD-CE LCD chip enable O 0 37 LCD-DI LCD data output O 0 38 VOLA Volume SW contact A I 4.8 39 VOLB Volume SW contact B I 4.8 40 GND Ground - 0 41 VDD +5V power supply - 5.0 42 NC No connection - ­43 MODEA Mode SW contact A I 0 44 MODEB Mode SW contact B I 0 45 NC No connection - ­46 NC No connection - ­47 NC No connection - ­48 NC No connection - ­49 NC No connection - ­50 NC No connection - ­51 SW/9Pro (VDD pull-up) - 5.0 52 9K/5K (Connecting to ground) - 0 53 NC No connection - ­54 NC No connection - ­55 NC No connection - ­56 CLK Power control IC clock O 0 57 STBY Power control IC stand-by O 5.0 58 LATCH Power control IC data latch O 5.0 59 DATA Power control IC data O 0 60 NC No connection - -
Port Description I/O (V)
61 NC No connection - ­62 NC No connection - ­63 NC No connection - ­64 MSOUT TPS detection O 4.8 65 NC No connection - ­66 NC No connection - ­67 NC No connection - ­68 MS-PL/FF MS mode selection O 0 69 T.LOAD Tape loading detection I 0 70 DOLBY Dolby NR on/off O 5.0 71 NC No connection - ­72 NC No connection - ­73 TEST (GND pull-down) - 0 74 NC No connection - ­75 NC No connection - ­76 NC No connection - ­77 A/B Tape forward-reverse SW I 0 78 MTL Metal tape mode on/off O 0 79 CAM A/B Tape side detection I 0 80 MSM MS gain control O 4.9 81 NK-IN AM signal level I 0 82 VDD +5V power supply - 5.0 83 AVDD +5V power supply - 4.8 84 GND Ground - 0 85 LANIN LAN data input I 0 86 LANOUT LAN data output O 0 87 GND Ground - 0 88 NC No connection - ­89 ILL-DET ILL detection I 0 90 EQ Metal tape detection I 4.8 91 +B-DET Battery level detection I 4.9 92 ACC-DET ACC level detection I 4.9 93 TAPE-EJ Tape eject SW I 4.9 94 T.IN Tape detection I 0 95 END-B Tape end detection I 0 96 END-A Tape end detection I 0 97 NC No connection - ­98 NC No connection - ­99 NC No connection - -
100 NC No connection - -
Note 1 : Voltage measuerments are with respect to ground, with a voltmeter (internal resistance : 10M ohms).
6.2. Display Block
IC601 : YEAMLC75853W
Pin
No.
1-33 SEG1-20 LCD segment data O 2.6 34-40 - Not used - ­41-43 COM1-3 LCD common output O 2.6
44 S41 Not used - -
45-49 KS1-6 Key scan signal O 5.2
50 KI1 Not used - 0
51-54 KI2-5 Key data input I 0
55 TEST (Connecting to ground) - 0 56 VDD +5V power supply - 5.2 57 VDD1 Ground through capacitor - 3.5 58 VDD2 Ground through capacitor - 1.8 59 VSS Ground - 0 60 OSC CR oscillator - 4.1 61 DO key data output O 5.2 62 CE Chip enable I 0 63 CLK LCD clock I 0 64 DI LCD data input I 0
Port Description I/O (V)
6
7 PACKAGE AND IC BLOCK DIAGRAM
7.1. Main Block
CQ-VS8180A
PA150 : YEP0PTY323A0
IC451 : YEAMLC72135C
7
CQ-VS8180A
PA100 : YEAU03SKM21
IC702 : YEAMLB1930MT
IC201 : C1BB00000284
IC651 : YEAMH12187ER
IC701 : C0DBZHZ00006
IC704 : AN8065SE1
8
Loading...
+ 18 hidden pages