Tote Vision LCD-1047VT, LCD-1047VR-TL User Manual

LCD-1047VT

LCD-1047VR/TL

Color TFT-LCD
TV Monitor
Operation Manual

www.totevision.com

LCD-1047VT/VR/TL

COLOR TFT-LCD TV Monitor

1. LCD-1047VT (stand alone unit)

2. LCD-1047TL (unit in flush mount kit)

3. LCD-1047VR (unit in rack kit)

OPERATION MANUAL

CONTENTS

SAFETY PRECAUTIONS

SUPPLIED ACCESSORIES

PREPARATION

Remote Control
Cable Connection

LOCATION OF USER CONTROLS

BASIC OPERATION

Monitor Installation

………………………

……………

……………

……………………

……………………

……………………

4,5

……

10

11

OSD USAGE

……

12
12
13

14
15

16

17
18
19

6

7
8

9

Basic OSD usage
Basic Setup
PC Setup

TV & Video Setup
OSD Setup

Before Calling for repair service

SPECIFICATIONS

LCD-1047VT/VR/TL
Available PC VGA Mode

Warranty Card

…………………………

……………………………

…………………………

…………………………

…………………

……………………

……………………

…………

SAFETY PRECAUTIONS

Improper use can result in electric shock and/or fire. In order to prevent potential
danger, please observe the following instructions when installing, operating and
cleaning the product. To ensure your safety and prolong the service life of your color
TFT-LCD TV monitor product, please read the following precautions carefully before
using the product.

■ All operating instructions must be read and understood before the product
is operated.

■ These safety and operating instructions must be kept in a safe place for
future reference.

■ All warnings on the product and in the instructions must be observed
closely.

■ All operating instructions must be followed.

■ Do not use accessories not recommended by the manufacturer.
Use of inadequate accessories can result in accidents.

■ This product must be operated on a power source specified on the
specification label. If you are not sure of the type of power supply used
in your home, consult your dealer or local power company.
For units designed to operate on batteries or another power source,
refer to the operating instructions.

■ The power cords must be routed properly to prevent people from stepping
on them or objects from resting on them.
Check the cords at the electrical outlet and product.

■ If you plan to use a 12V DC power supply unit other than the AC adapter
supplied with the product, make sure the power supply unit provides stable
voltage with minimum fluctuations.

■ Do not overload AC outlets or extension cords.
Overloading can cause fire or electric shock.

■ Never insert an object into the product through vents or openings.
High voltage flows in the product, and inserting an object can cause
electric shock and/or short internal parts.
For the same reason, do not spill water or liquid on the product.

■ Do not attempt to service the product yourself.
Removing covers can expose you to high voltage and other dangerous
conditions. Request a qualified service person to perform servicing.

■ If any of the following conditions occurs, unplug the power cord from the
AC outlet, and request a qualified service person to perform repairs.
a. When the power cord or plug is damaged.
b. When a liquid was spilled on the product or when objects have fallen
into the product.
c. When the product has been exposed to rain or water.
d. When the product does not operate properly as described in the
operating instructions.
Do not touch the controls other than those described in the operating
instructions.

4

SAFETY PRECAUTIONS

Improper adjustment of controls not described in the instruction can cause
damage, which often requires extensive adjustment work by a qualified technician.
e. When the product has been dropped or damaged.
f. When the product displays an abnormal condition. Any noticeable
abnormality in the product indicates that the product needs servicing.

■ In case the product needs replacement parts, make sure that the service person
uses replacement parts specified by the manufacturer, or those with the same
characteristics and performance as the original parts.
Use of unauthorized parts can result in fire, electric shock and/or other danger.

■ Upon completion of service or repair work, request the service technician to
perform safety checks to ensure the product is in proper operating condition.

■ When mounting the product on a wall or ceiling, be sure to install the product
according to the method recommended by the manufacturer.

■ Unplug the power cord from the AC outlet before cleaning the product. Use a
damp cloth to clean the product. Do not use liquid cleaners or aerosol cleaners.

■ Unplug the power cord from the AC outlet if you do not use the product for an
extended priod of time.

■ Do not use the product near water, such as bathtub, washbasin, kitchen sink,
laundry tub, swimming pool or in a wet basement.

■ Keep the product away from direct rays of the Sun-light.

■ Do not place the product on an unstable cart, stand, tripod or table. Placing the
product on an unstable base can cause the product to fall, resulting in serious
personal injuries as well as damage to the product. Use only a cart, stand,tripod,
bracket or table recommended by the manufacturer or sold with the product.
When mounting the product on a wall, be sure to follow the manufacturer's
instruction. Use only the mounting hardware recommended by the manufacturer.

■ When relocating the product placed on a cart, it must be moved with the utmost
care. Sudden stops, excessive force and uneven floor surface can cause the
product to fall from the cart.

■ The vents and other openings in the cabinet are designed for ventilation.
Do not cover or block these vents and openings since insufficient ventilation
can cause overheating and/or shorten the life of the product. Do not place the
product on a bed, sofa, rug or other similar surface, since they can block
ventilation openings. This product is not designed for built-in installation; do
not place the product in an enclosed place such as a bookcase or rack, unless
proper ventilation is provided or the manufacturer's instructions are followed.

■ The LCD panel used in this product is made of glass.
Therefore, it can break when the product is dropped or applied with impact. Be
careful not to be injured by broken glass pieces in case the LCD panel breaks.

■ Keep the product away from heat sources such as radiators, heaters, stoves
and other heat-generating products (including amplifiers).

■ The LCD Panel is a very high technology product with 786,432 thin film
transistors, giving you fine picture details. Occasionally, a few non-active pixels
may appear on the screen as a fixed point of blue, green or red.
Please note that this does not affect the performance of your product.

(Continued)

5

SUPPLIED ACCESSORIES

Please check to make sure the following accessories are included with this product.

TM390 ... XGA

LCD-2200VT

TM400 ... SXGA

WSXGA

Color TFT-LCD
TV Monitor (NT SC)
Operation M anual

Operation Manual (x1)

Size AAA Battery (x2)

Remote Control (x1)

DESK Stand (x1) Screws Wall Mount Latch(x1)

PC VGA Cable (x1)

AC Adapter (x1)

PC Stereo Cable (x1)

6

AC Cord (x1)

PREPARATION

Remote Control

■ Use the remote control by pointing it towards the remote sensor window.
Objects between the remote control and sensor window may prevent proper
operation.

!

Cautions regarding use of remote control

■ Do not drop the remote control . In addition, do not expose the remote
control to liquids, and do not place in an area with high humidity.

■ Do not install or place the remote control under direct sunlight.
The heat may deform the unit.

■ The remote control may not work properly if the remote sensor window of
the main unit is under direct sunlight or strong lighting. In such case,
change the angle of the lighting or LCD TV monitor set, or operate the
remote control closer to the remote sensor window.

Batteries for Remote Control
If the remote control fails to operate the LCD TV Monitor functions, replace
the batteries in the remote control.

1 Open the battery cover.

2 Insert batteries (two Size-AAA batteries, Supplied with product).

■ Place batteries with their terminals corresponding to the (+) and (-)
indications in the battery compartment.

3 Close the battery cover

!

Cautions regarding batteries

Improper use of batteries can result in a leakage of chemicals and/or explosion. Be sure to
follow the instructions below.

• Place batteries with their terminals corresponding to the (+) and (-) indications.

• Different types of batteries have different characteristics. Do not mix batteries of different
types.

• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of
new batteries and/or cause old batteries to leak chemicals.

• Remove batteries as soon as they are non-operable. Chemicals that leak from batteries
can cause a rash. If chemical leakage is found, wipe with a cloth.

• The batteries supplied with the product may have a shorter life expectancy due to storage
conditions.

• If the remote control is not used for an extended period of time remove batteries from the
remote control

7

PREPARATION

Rear view of main unit

1. BNC Video OUT is
passive loop out.

2. If BNC Video IN is
applied, RCA Video IN
will be disabled.

(Continued)

Cable Connection

EXT. Speaker

KEY control

*

(option) BNC Video

RS-232 (option)

IN & loop out

EXT. DC

TV Antenna

*VIDEO OUT

ANALOG RGB

S-VIDEO PC SOUND

VIDEO OUT

*

is active output for VCR recording for TV or composite video

Y, Pb, Pr

<

Main board connectors>

Power input
(DC 12V2A)

R L
Sound IN

VIDEO IN

AUDIO OUT

input. This can be used for a diversity antenna. If S-Video or component
input is selected, display of this output will be changed to black and white
because the color of the original input signal is already separated.
In PC mode you will get TV signal.

IR IN

8

LOCATION OF USER CONTROLS

Control Panel (C/P) on the front of main unit

MenuPOWER ▼ CH ▲▼ VOL ▲

IR window

Remote control (R/C)

Sound mute

Select Under Scan

Menu

Vol (▲)/(▼)

▲ Increase volume (up)

▼ Decrease volume (down)

Power

Indicator

Power

Decrease volume
Increase volume
Channel down / Move down
Channel up / Move up

Mode select/Menu

Auto Program

Power

Erase present Channel

Ch (▲)/(▼)
▲Selects next higher channel.
▼Selects next lower channel.

Channel select

Select input source Auto Color

to set default Display setting

9

BASIC OPERATION

POWER On / Off / Standby

Available Mode ■ Yes / □ No

■ PC ■ Video ■ S-Video ■ TV

■ by Control Panel (C/P)

Press the POWER

1

The

2

power indicator lights green.

3

Press again the Power button to turn off.

button to turn on the main unit.

IR Window

Power Indicator

■ by Remote Control (R/C)

Press the Power

1

P

2

ower indicator changes from red to green.

3

Press again the
indicator changes from green to red and main
unit turns into standby mode.

button to turn on the main unit.

Power

Switching PC / TV / VIDEO / S-VIDEO Mode

With Remote Control (R/C)

1 Press the SELECT to change input source.

From Control Panel (C/P)

1.

Press the Menu key less than 2

sec. to select the next input source.

button then the power

10

2.

Press the MENU key more than 2

sec. to access menu on screen.

3.

Press the Ch▲/▼ and Vol▲/▼ to move

the cursor to the desired selected source.

4 If you don't want to change source,
just leave it or press MENU Key.

Monitor Installation

Available Mode ■ Yes / □ No

■ PC □ Video □ S-Video □ TV

1

Double click

from [My Computer] folder

[Control Panel ] icon

2

Double click

.

[Control Panel] folder.

[Display]

icon from

3

Select

window.

4

Click

[Settings]

[Advanced...]

in [Display Properties]

.

5

Select [Monitor] in the window shown

above.

[Refresh Frequency:]

6

Set

7

Finally, click [Properties].

at 60Hz.

11

BASIC OSD USAGE

Main Menu Screen

1

Press the

2

Press the

3

Press the

4

Press the

Note:

Menu

of R/C or C/P to display the OSD menu screen.

Ch▲/▼
Sel

Exit

R/C - Remote Control & C/P - Control Panel

of R/C or C/P to move the cursor to

of R/C or

of R/C or select the

Basic Setup

Select item

OSD MENU

Press the
or press the

Color
Picture
Function
OSD Menu
Misc.
Sound

Menu

of C/P to select the menu icon.

Vol▼

of R/C

Ch▼ of C/

desired menu

Exit

of OSD menu to disappear the main menu screen.

Available Mode ■ Yes / □ No

■ PC ■ Video ■ S-Video ■ TV

Press the

P

or press the

icon

Vol▲

.

of R/C

Ch▲ of C/

1024x768 60Hz

Contrast
Brightness
Gamma
Color Temp
Color Adjust

P

PICTURE

MISC.

SOUND

12

Color
Picture
Function
OSD Menu
Misc.
Sound

Signal Source -

Display mode -

Reset -

YES, NO

Sound

Volume

1024x768 60Hz

H.Position
V.Position
Phase
Clock
Sharpness

PC, CVBS , S-Video, Y/Pb/Pr, TV

Normal, Under Scan

ON OFF

PC Setup

Available Mode ■ Yes / □ No

■ PC □ Video □ S-Video □ TV

Selected item

Color

PICTURE

Press the
or press the

Vol▼

Ch▼ of C/

Color
Picture
Function
OSD Menu
Misc.
Sound

Color
Picture
Function
OSD Menu
Misc.
Sound

of R/C

P

Contrast
Brightness
Gamma
Color Temp
Color Adjust

H.Position
V.Position
Phase
Clock
Sharpness

Press the
or press the

1024x768 60Hz

1024x768 60Hz

Vol▲

of R/C

Ch▲ of C/

P

Function

V-Position

H-Position

1024x768 60Hz

Color
Picture
Function
OSD Menu
Misc.
Sound

Move down Move up

AUTO Adjust YES NO
AUTO color YES NO

■ Automatically adjusted items are bellow

1) Frequency, 2) Phase

3) H-position of PC Setup

4) V-Position of PC Setup

5) Canceling Speaker Mute

Video

Move left Move right

ideo Vide

Video

13

TV &Video Setup

Available Mode ■ Yes / □ No

□ PC ■ Video ■ S-Video ■ TV

Selected item

Channel

Edit

Under Scan

Press the
or press the

Vol▼

of R/C

Ch▼ of C/

Press the

P

or press the

Vol▲

of R/C

Ch▲ of C/

UP/DOWN 4
Add/Erase ADD Erase
Select AIR STD HRC IRC
AUTO Search YES NO
Fine Tune -2

Normal Screen ..... The screen takes the source of 4:3 aspect

ratio as its full-sized regular picture. You may loose some of
the edge of the original image.

Under scan mode ...... This mode enables the user to display

100% of input image without hiding any image of Source. Video
will be displayed with small black border around the border.
Some video source which is non-standard format may break
the black border.

P

Under ScanNormal Display

14

OSD Setup

Available Mode ■ Yes / □ No

■ PC ■ Video ■ S-Video ■ TV

Selected item

Language

H-Position

Press the
or press the

Vol▼

of R/C

Ch▼ of C/

Press the

P

or press the

Vol▲

of R/C

Ch▲ of C/

P

1 Press the Menu of R/C or C/P to select the Language.
The language select menu screen will appear.

2 Press the Vol▲/▼ of R/C or press the Ch▲/▼ of C/P to move
the cursor to the English or other.

3 Press the Vol ▲ of R/C or Menu of C/P to select the desired
language. Then press Exit to move to previous menu screen.

move right the OSD menu boxmove left the OSD menu box

■■

V-Position

■

Background OpaqueTranslucent

Duration Time

■ The range of controlling the duration time of the OSD menu is from
5 sec. up to 30 sec. Default setting is 10 sec.

move up the OSD menu boxmove down the OSD menu box

■

15

Before calling for repair service...

■ Before calling for repair service, check the following items for possible remedies to the
encountered symptoms.

Problem Check below

•

There is no
picture or sound
(TV,Video,PC).

There is no
sound (TV,Video
PC).

There is no
picture or sound,
just noise(TV).

Picture is not
clear (TV).

Make sure the AC adapter is properly inserted in the

power outlet.

•

Make sure the main power button of the main unit is on.

•

Make sure the signal cables are securely connected.

•

Make sure the power of an external input device is on.

•

Make sure the input mode is set to proper mode.

•

Fluorescent lamp may have reached the end of service life.

•

Make sure the volume is not set to minimum.

•

Make sure the sound is not set to mute.

•

Make sure the sound cables are securely connected.

•

Make sure the antenna cable is properly connected.

•

Bad reception can be considered.

•

Make sure the antenna cable is properly connected.

•

Bad reception can be considered.

Reference

Pages

8

9
8

­9
19

9
9
8

8

-

8

-

Picture is not
clear (PC).

The picture is not
clear (Video).

The picture is not
sharp (TV).

The picture is
doubled or tripled
(TV).

There are stripes
on the screen or
color fade.

•

Operate the Auto Adjust.

•

Reset the Frequency and the Phase.

•

Check whether the Video Type is set up in the Video Setup

menu.

•

The reception may be weak.

•

The state of broadcast may also be bad.

•

Make sure the antenna cable is securely connected.

•

Make sure the antenna is facing the right direction.

•

There may be reflected electric waves from mountains

or buildings.

•

Check this unit receiving interference from other devices.
Transmission antennas of radio broadcasting stations and
transmission antennas of amateur radios and cellular
phones may also cause interference.

•

Use the unit as far apart as possible from devices that may
cause possible interference.

13
13

12,14

16

SPECIFICATIONS

Color TFT-LCD TV Monitor

(Analog RGB)

1024 * 768, XGAResolution

262,144 ColorsStandard ColorColor

250 cd/m

450 : 1Contrast Ratio

H : 160 ˚ V : 160 ˚Viewing Angle

Amorphous Si TFT-LCDTypePanel

210.4 * 157.8mmActual Display Size

10.4˝, 264.16mmDiagonal Length

30~61 KHzH-FrequencyPC Signal

56~75 HzV-Frequency

LCD-1047VT/VR/TL

2

(nit)Brightness

0.7Vp-pSignal Level

Composite/ S-VIDEO/YPbPr / CATV(NTSC)Input SignalVideo / TV

NTSC / PAL (Auto Sensing)Color Signal Type

YPbPr/CVBS/S-Video: Stereo, TV : monoSound Signal Type

AC100~240V, 50/60Hz, DC12VPower Voltage

Typ. 20WattStandardPower Consumption

Max. 3 WattPower Save Mode

Standard : 2x 2 Watts(VT/VR), 5W(TL),Speaker (power option upon order)

270 x 230 x 50 mm, without desk standW*H*D mmSize

2 Kg w/o accessoriesWeight

17

SPECIFICATIONS

VGA Input Signal

Available PC VGA Mode

Resolution

640 x 480

800 x 600

1024 x 768

V-Frequency

(Hz)

60

72

75

56

60

72

75

60

70

H-Frequency

(KHz)

37.9

37.9

37.9

31.5

37.9

37.5

35.1

37.9

48.1

46.9

48.4

56.5

Pixel Rate

(MHz)

31.50085640 x 350

31.50085640 x 400 DOS

35.50085720 x 400

25.175

31.500

31.500

36.000

40.000

50.000

49.500

44.90035.543

65.000

75.000

Standard

Type

VESA Standard

VESA Standard

VESA Standard

Industry Standard

VESA Standard

VESA Standard

VESA Guidelines

VESA Guidelines

VESA Standard

VESA Standard

Industry Standard

VESA Guidelines

VESA Standard

Remark

VGA

SVGA

XGA

75

60.0

78.750

VESA Standard

VESA Standard108.00067.5751152 x 864

-

18

Warranty

ONE YEAR LIMITED WARRANTY

Tot eVi si on warrants to the original purchaser that this product is free from defects in workmanship and material under normal use and
conditions for a period of 1 year from the date of original purchase, subject to the limitations below. Should service be required by reason of
any defect or malfunction dur ing the warranty period, Tot eVis i on will repair or at its discretion replace this product, without charge (except
for a $15.00 charge for handling, packing, return shipping, and subject to verification of the defect or malfunction), upon delivery of this
product to the Factory Service Center listed below with proof of date of purchase. During the warranty period Tot eVis i on will repair or
replace, free of charge, defective units

OR OTHER CAUSES NOT ARISI NG OUT OF MANUFACTURER’S DEFECTS I N MATERI ALS OR WORKMANSHI P.

Before returning this product for service:

1. If it is necessary to pack the unit in other than original carton and protectors, please insure proper packaging for good protection.

2. Enclose a photocopy of your dated sales receipt , credit card statement, or other proof of the date of purchase, a description of your
complaint, your name, address and day ti me telephone number. (Do not use P.O. Box numbers si nce UPS cannot deliver to P.O. Boxes.)
Your warranty registration information must be on file in our office as a method of identification. If proof of original ownership is not in our
records, the repairs will be treated as “out-of-warranty” and your unit will be returned to you after you have paid for repair and handling
char ges.

3. For “In Warranty repair s” enclose a check or money order payable to the order of Tot eVis i on for the sum of $15.00 for r eturn postage and
handling.

4. Ship the unit prepaid to the Factory Service Center listed below.

5. If your unit needs service after the warranty period has expired, ship it prepaid and i nsured to the Factory Service Center below. Enclose
a description of your complaint; your name, company name, address, and day time telephone number. You will be advised of estimated repair
char ges.
NOTE: This warranty is valid only if the product is used for the purpose for which it was designed. It does not cover:
(i ) pr oducts which have been damaged by negligence, misuse, accidents, abuse, acts of God, or units which have been modified or repaired
by unauthorized persons,
(ii ) cracked or broken units or components or units damaged by excessive heat or cold, or units exposed t o excessi ve UV light.
(iii) products which have their serial numbers removed, altered or rendered illegible,
(iv) products that have cold cathode florescent tubes (CCFTs) that do not provide sufficient illumination,
(v) the cost of shipping this product to the Factory Service Center and its return to you.
No warranty, expressed or implied, as to merchantability or fitness for a particular use is made beyond this Limited Warranty. ToteVi si on
will not be liable for incidental or consequential damages or lost profits arising from product defects or malfunctions. This warranty is valid
only in the United States of America and does not extend to owners of the product subsequent to the original purchaser. Any applicable
implied warranties are also limited to 1 year and Tot eVi sion will not be liable for consequential damages. (Some states do no allow
limitations on implied warranties or exclusions of consequential damages, so that these restrictions may not apply to you.) This warranty
gives you specific legal ri ght s, and you may also have other rights which vary from state to state.

As a precondition to receiving any of the benefits of this limited warrant y, your completed warranty regi stration information must be
on f i le i n our offi c e. IF YOUR INFORMATION I S NOT ON FI LE WITH US, ALL WARRANTY CLAI MS WILL BE DENI ED. TO
PROTECT YOUR WARRANTY, MAIL YOUR REGI STRATION I NFORMATION TODAY! Submi ssi on of a uni t det er mi ned t o be n ot
defective will result in a charge to you for testing and handling the unit. Thoroughly test your unit before submitting it for warranty claim
repair.
Send unit to: TOTEVISION SERVICE CENTER 1319 Dexter Avenue N. # 020, Seattle, WA 98109
For further information: call [phone] or fax [phone]

_____________________________________________________________________________________________________

Protect your Warranty by completing and mailing this form to: ToteVision, 1319 Dexter Avenue N. # 020, Seattle, WA 98109

Model Number: _______________________Serial Number: _______________________
Name: _____________________________________________________________________
Address: ____________________________________________________________________
City: ___________________________________ Stat e:
Telephone number: (____________)_______________________________
Dealer: ______________________Dealer City: _____________________ State: _______________

WHICH ARE NOT DEFECTI VE DUE TO ORDINARY WEAR AND TEAR, USER ABUSE,

WARRANTY REGISTRATION

_______

Zip: ________________

Version 082203

19