TOSHIBA AMERICA INFORMATION SYSTEMS
STORAGE DEVICE DIVISION
IRVINE, CALIFORNIA
SD-R2612
CD-RW/DVD-ROM COMBINATION MOBILE DRIVE
USER MANUAL
CONTENTS
Introduction..............................................................................1
Setup ........................................................................................3
Using the CD-RW/DVD-ROM Combo Drive............................4
Troubleshooting.......................................................................7
Specifications ..........................................................................8
Drive Connectors................................................................... 11
INTRODUCTION – SD-R2612
General Features
CD-RW disc write/rewrite at 4X – 24X
CD-R disc write at 4X - 24X
3-way Disc Eject (eject button, software, emergency eject hole)
Average Access Time
CD 130ms
DVD-ROM (single) 130ms
DVD-ROM (dual) 150ms
DVD-RAM 250ms
Horizontal or Vertical Mount
2MByte Buffer
Playback interchangeability for CD-ROM and DVD-ROM discs
Regionalization (RPC2 compliance) (DVD)
BUS Interface ATAPI
Format Compatibility
CD:
• CD-DA (Red Book) - Standard Audio CD & CD-TEXT
• CD-ROM (Yellow Book Mode1 & 2) - Standard Data\
• CD-ROM XA (Mode2 Form1 & 2) - Photo CD, Multi-Session
• CD-I /FMV (Green Book, Mode2 Form1 & 2, Ready, Bridge)
• CD-Extra/ CD-Plus (Blue Book) - Audio & Text/Video Video-
• CD (White Book) - MPEG1 Video
DVD
• DVD DVD-ROM (Book 1.02)
• DVD-Video (Book 1.1)
• DVD-R (Book 1.0, 3.9G)
• DVD-R (Book 2.0, 4.7G) - General & Authoring
• DVD+R (Version 1.0) DVD±RW DVD-RAM P
• DVD+R (Version 1.0)
• DVD±RW
• DVD-RAM
1
Front Panel
Figure 1.SD-R2612 CD-RW/DVD Combo Drive Front Panel
Loading
Tray
Busy
Indicator
Eject
Button
Emergency
Eject Hole
Load disc using tray.
The LED lights green or amber when the drive is operating (LED is amber when drive is
writing.)
The Eject button is used to open the disc tray so you can install or remove a disc.
The emergency eject hole is to be used only when the Loading Tray will not open when
Eject button is pressed.
SETUP – SD-R2612
Toshiba recommends that only trained professionals install this CD-RW/DVD-ROM Combo drive into
your laptop/notebook.
Installation Notes
• The SD-R2612 CD-RW/DVD-ROM Combo drive has no jumpers that need to be set
• Mounting orientation: 15° (horizontally), 15° vertically (volume control in down position), 30°
(drive with volume control in up position).
• When mounting drive use 4 M2-PO.4 tapping holes located on the left and right sides of drive.
• When mounting drive, the tightening torque of the four screws must be even. Recommended
screw tightening torque is 2N
• For clearance around the front bezel, it is recommended that a clearance of more than 0.8mm
should be left in all directions.
Software Driver
Toshiba's SD-R2612 drive does not require any unique device drivers for Windows '98/2000/XP/NT.
After installing your drive and re-booting, your system should recognize your drive. Win '98/2000/XP/NT
Operating Systems support all Toshiba's ATAPI drives natively. If you prefer using DOS, download the
ATAPI driver from our web site.
3
USING THE CD-RW/DVD-ROM Combo Drive – SD-R2612
Drive Operation
Inserting Media
To insert media perform the following steps:
Figure 1.Inserting Disc
1. Open the drive's loading tray by pressing the Eject Button and pulling out the tray.
2. Place media disc into drive's loading tray, and lightly press down on the inner portion of the disc.
3. Gently close the disc tray.
Removing Media
To remove media disc from the drive, perform the following steps:
1. Open the loading tray by pressing the Eject Button, and pulling tray out.
2. Grasp disc by it's outer edge, and lift out of loading tray.
3. Gently close the loading tray.
Usage Guidelines
• Keep the disc tray closed when not using the CD-RW/DVD-ROM Combo drive
• Do not press down on the disc tray when opening or closing it.
• Do not place objects on the disc tray
• Never use a damaged, broken, or deformed disc
• Do not press the Eject button while the drive is playing a DVD movie or accessing a disc. To
stop a DVD movie, click Stop button in the DVD player application program
4
-
NOTE: High-speed drives spin the disc at a high rotational speed. If a disc has printing on only half of
the disc, or if there is a slight imbalance in the disc, the imbalance is greatly magnified by the high
speed, causing the drive to vibrate or produce a fan-like noise. These effects are inherent in the high
speed technology and do not indicate a problem with the drive.
Regional Coding
Region Protection Coding (RPC) of DVD Discs: this feature is supported on DVD Players and is used
with DVD-Video Discs (i.e. movies). Currently, the motion picture industry has divided the world into
different regional "zones." These regions or "zones" correlate to the regional markets into which the
motion picture industry releases movies. Simply put, RPC Codes are placed on Movie Discs marketed
throughout the world based on the region of the world where they are being sold. These RPC codes
help to control and prevent the pirating of new release movies into other motion picture market regions
prior to their true release dates within those markets.
The SD-R2612 DVD-ROM/CD-RW drive supports the current RPC phase 2 industry specifications. This
means that when the DVD-ROM drive ships from the factory it is set to the region for which the
Operating System was intended. In other words the drive is set to support the Region 1 (North America)
Operating System and will only play Region 1 (North America) DVD-Video movie discs.
Emergency Ejection
CAUTION: The following procedure is intended only as a last resort when
pressing the eject button fails to open the Loading Tray.
1. Turn computer power OFF by properly shutting down system.
2. Insert a solid bar (i.e. large paper clip) into Emergency Eject hole and push in as shown in the
picture below.
3. Loading tray will open/eject.
Figure 2.Using Emergency Eject
5
Handling Media
DVD media is sensitive to dust and fingerprints. Carefully handle media by its edges only. If a DVD
movie skips or hangs during playback, clean the media. Most DVD video playback issues are mediarelated and can be remedied by proper handling and care of media.
Cleaning Media
Try to avoid touching the read area (underside) of the disc as dirt and smears will degrade the disc
accessing speed.
If the disc becomes dirty wipe it with a damp soft cloth. Avoid cleaning in a circular motion, but rather
from the inner side outward.
6
TROUBLESHOOTING – SD-R2612
Problem
Disc tray cannot be opened
Drive is not recognized by
system
Drive is not recognized by
system during Boot process,
but is recognized by the
Operating System (i.e. XP,
Win2000, Win98, Win NT, etc.)
BUSY Indicator LED flashes
slowly
BUSY Indicator LED is
constantly ON
DVD-ROM can not play a DVD
in the drive or certain types of
CD media (i.e. CD-plus, etc.)
Solution
• Check that there is power to drive.
• Use Emergency Eject instructions to open tray.
• Is the drive connected properly? Are all cables plugged in
properly (e.g. Power Cable, Interface Cable and Audio Cables).
• Is the software driver loaded? On a step-by-step (F8) Boot of the
system is the CD-RW/DVD-ROM Combo drive recognized?
(BIOS / DOS reports "device driver not found" or "no valid
drivers selected."). If not, Contact Technical Support.
• Has the CD-RW/DVD-ROM Combo drive software driver been
corrupted by a virus. Run a Virus Scan program and repair if
possible. Contact Technical Support if the Virus renders the CDRW/DVD-ROM Combo drive software drivers not useable.
• Is the CD-RW/DVD-ROM Combo drive software driver loaded?
On a step-by-step (F8) Boot of the system is the CD-RW/DVDROM Combo drive recognized?
(BIOS / DOS reports "device driver not found" or "no valid DVD
drivers selected."). If not, Contact Technical Support.
• Has the Windows CD-RW/DVD-ROM Combo drive software
driver program been corrupted by a virus. Run a Virus Scan
program and repair if possible. Contact Technical Support if the
Virus renders the software drivers not useable.
• The disc may be dirty Clean it with a soft damp cloth. Avoid
cleaning the disc using a circular motion. The disc should be
wiped in a radial direction. That is, from the inner side outward.
• The laser lens may have become cloudy or blocked by
particulate matter. Please contact Technical Support.
• Possible Hardware Problem. Please contact Technical Support.
• Is the CD-RW/DVD-ROM Combo drive driver loaded
• Is the DVD disc the correct format for the type of system that you
are using? (i.e. on a PC an ISO9660 IBM compatible PC format
as opposed to Apple/Mac HFS disc or UNIX disc formats which
will not function).
• Do you have the correct software applications program/drivers
installed to run a DVD disc?
• Has the Windows CD-RW/DVD-ROM Combo drive software
driver program been corrupted by a virus. Run a Virus Scan
program and repair if possible. Contact Technical Support if the
Virus renders the software drivers not useable.
7
SPECIFICATIONS –SD-R2612
General
Interface: ATAPI
Format Compatibility
CD:
• CD-DA (Red Book) - Standard Audio CD & CD-TEXT
• CD-ROM (Yellow Book Mode1 & 2) - Standard Data\
• CD-ROM XA (Mode2 Form1 & 2) - Photo CD, Multi-Session
• CD-I /FMV (Green Book, Mode2 Form1 & 2, Ready, Bridge)
• CD-Extra/ CD-Plus (Blue Book) - Audio & Text/Video
• Video-CD (White Book) - MPEG1 Video
DVD
• DVD DVD-ROM (Book 1.02)
• DVD-Video (Book 1.1)
• DVD-R (Book 1.0, 3.9G)
• DVD-R (Book 2.0, 4.7G) - General & Authoring
• DVD+R (Version 1.0) DVD±RW DVD-RAM P
• DVD+R (Version 1.0)
• DVD±RW
• DVD-RAM
Note: All DVD/CD formats, except CD-Red Book (audio), require additional application specific software
and/or hardware. The drive is capable of reading these data formats. However, in order to run applications
that use these formats, you must first have the required software and/or hardware.
Data Disc Capacities
DVD-ROM
DVD-R (Ver 1)
DVD-R (Ver 2.0)
DVD-RAM (Ver 2.1)
CD
8
4.377GB (DVD-5)
7.959GB (DVD-9)
8.754GB (DVD-10)
15.917GB (DVD-18)
3.679GB
4.377GB
4.377GB
656.5MB (mode 1)
748.8MB (mode 2)
Performance
Transfer Rate
DVD (Single)
DVD (Dual)
DVD+/-R
DVD+/-RW
DVD-RAM (Ver 2.1)
CD-ROM/R (Read, Mode 1)
CD-RW Read (Mode 1)
10,800KB/second max (8X max)
8,100KB/second max (6X max)
8,100KB/second max (6X max)
8,100KB/second max (6X max)
5,400KB/second max (4X max)
3,600KB/second (24X max)
3,600KB/second (24X max)
Random Access Time
CD-ROM 130ms
CD-RW 130ms
DVD (single) 130ms
DVD (dual) 150ms
DVD-R/+R 150ms
DVD-RW/+RW 150ms
DVD-RAM 250ms
Data Error Rate
-15
Max
DVD-ROM
CD-ROM
10
-12
10
Max (Mode 1)
-9
Max (Mode 2)
10
Data Buffer 2MB
Reliability
MTBF 80,000 hours
• Power ON Hours 2,000 hours/year
SEQ Read 42.6%
• Seek 9.3%
• Write 31%
• Power ON/OFF 7.7%
• Drawer Test 9.3%
Drive Lifetime 5 years
Drawer Load/Release 10,000 times
9
Environmental
Ambient Temperature
Operating 5° to 50° C (41° to 122° F)
Storage -40° to 65° C (-40° to 149° F)
Relative Humidity
Operating 10% to 90%
Storage/Shipping 5% to 95% (wet bulb 40° C max)
Vibration
Operating (5 to 500 Hz) (read)
Operating (5 to 500Hz) (write)
Non-operating (10 to 500Hz)
2.45 m/s2 (0.25G) (O-P)
2.45 m/s2 (0.25G) (O-P)
9.8 m/s2 (1.0G) (O-P)
Packing (10 to 25 Hz) 9.8 m/s2 (1.0G) (O-P)
Shock (Non-operating) 490 m/s
2
[50G]
Acoustical Noise 40dB
Power
DC Voltage and Current Requirements +5V ±5% (Operating)
Physical
Height 0.5" (12.7mm)
Width 5.04" (128mm)
Depth 5.00" (127mm)
Weight 6.35oz (.18kg)
Connectors
IDE Interface Connector 50 Pin I/F ATAPI Standard
Regulatory
The SD-R2612 DVD Writeable drive has been certified by the following
regulatory agencies:
• UL 1950
• CSA C22.2 No. 950
• TUV (EN60950I)
• CE standard
• DHHS 21 CFR Sub-Chapter J
• FDA CFR21, EN60825
10
Drive Connectors –SD-R2612
Figure 1.SD-R2612 DVD Writeable Drive Rear Panel – Connector
ATAPI
Connector
Table 1.Interface Pin Assignments
A 50-pin ATAPI interface connector is found at the rear of the SD-R2612 CD-RW/DVDROM Combo drive. Connecting cable should use Japan Aviation Electronics Industry
Limited KX14-50Series L or equivalent connector.
PIN
NO.
1 O Audio L-CH 2 O Audio R-CH
3 Audio Ground 4 Digital Ground
5 I /RESET 6 I/O DD8
7 I/O DD7 8 I/O DD9
9 I/O DD6 10 I/O DD10
11 I/O DD5 12 I/O DD11
13 I/O DD4 14 I/O DD12
15 I/O DD3 16 I/O DD13
17 I/O DD2 18 I/O DD14
19 I/O DD1 20 I/O DD15
21 I/O DD0 22 O DMARQ
23 Ground 24 I /DIOR: /
25 I /DIOW:STOP 26 Ground
27 O IORDY: /
29 O INTRQ 30 O /IOCS16
31 I DA1 32 I/O /PDIAG
33 I DA0 34 I DA2
35 I /CS1FX 36 I /CS3FX
37 I/O /DASP 38 I +5V (Motor)
39 I +5V (Motor) 40 I +5V (Motor)
41 I +5V (Logic) 42 I +5V (Logic)
43 Ground 44 Ground
45 Ground 46 Ground
47 I CSEL 48 Ground
49 I Vendor Unique* 50 I Vendor Unique*
*Vender Unique, don't connect pins
I/O SIGNAL NAME PIN
NO.
28 I /DMACK
DDMARDY:
DSTROBE
I/O SIGNAL NAME
HDMARDT:
HSTROBE
11
Loading...