Toshiba MW20FN3-R, MW24FN3-R User Manual

DIGITAL VIDEO

Introduction

COMBINATION FLAT COLOR TELEVISION AND VIDEO CASSETTE RECORDER / DVD VIDEO PLAYER

MW20FN3/R MW24FN3/R

OWNER’S MANUAL

Connections

Basic setup

TV operation

Playback

(VCR)

Recording (VCR)

Other functions

(VCR)

Basic playback

(DVD)

Advanced

playback

(DVD)

Function setup

(DVD)

Others

Introduction

IMPORTANT SAFEGUARDS

The lightning flash with arrowhead symbol, within an

RISK OF ELECTRIC SHOCK

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

DO NOT OPEN

equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that ma y be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not expose this appliance to

rain or moisture.

WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device,

CAUTION:

CAUTION: THIS DIGITAL VIDEO PLAYER EMPLOYS A LASER SYSTEM.

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the distance between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance with the

FCC (Federal Communications Commission) Rules could void the user's authority to operate this equipment.

TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS USER'S GUIDE CAREFULLY AND RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE MAINTENANCE, CONTACT AN AUTHORIZED SERVICE LOCATION-SEE SERVICE PROCEDURE.

USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

TO PREVENT DIRECT EXPOSURE TO LASER BEAM, DO NOT TRY TO OPEN THE ENCLOSURE. VISIBLE LASER RADIATION MA Y BE PRESENT WHEN THE ENCLOSURE IS OPENED . DO NOT STARE INTO BEAM.

event that third party copyrights and other rights are not violated.

Location of the required Marking

The rating sheet and the safety caution are on the rear of the unit.

CERTIFICATION: COMPLIES WITH FDA RADIATION PERFORMANCE STANDARDS, 21 CFR SUBCHAPTER J.

LINE 1 IN

OUT PUT

VHF/UHF

VIDEO

DIGITAL AUDIO

(MONO)

COAXIAL

AUDIO

IMPORTANT SAFEGUARDS

1. READ INSTRUCTIONS

All the safety and operating instructions should be read before the unit is operated.

2. RETAIN INSTRUCTIONS

The safety and operating instructions should be retained for future reference.

3. HEED WARNINGS

All warnings on the unit and in the operating instructions should be adhered to.

4. FOLLOW INSTRUCTIONS

All operating and use instructions should be followed.

5. CLEANING

Unplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

6. ATTACHMENTS

Do not use attachments not recommended by the unit’s manufacturer as they may cause hazards.

7. WATER AND MOISTURE

Do not use this unit near water. For example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.

8. ACCESSORIES

Do not place this unit on an unstable cart, stand, tripod, bracket, or table. The unit may fall, causing serious injury, and serious damage to the unit. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer.

8A. An appliance and cart combination should be moved with care. Quick stops,

excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

9. VENTILATION

Slots and openings in the cabinet and in the back or bottom are provided for ventilation, and to ensure reliable operation of the unit, and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the unit on a bed, sofa, rug, or other similar surface. This unit should never be placed near or over a radiator or heat source. This unit should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions ha ve been adhered to.

10. POWER SOURCES

This unit should be operated only from the type of power source indicated on the rating plate. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For units intended to operate from battery power, or other sources, refer to the respective pages on this Owner’s Manual for their operating instructions.

11. GROUNDING OR POLARIZATION

This unit is equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Instead of the polarized alternating-current line plug, your unit may be equipped with a 3-wire grounding-type plug (a plug having a third (grounding) pin). This plug will only fit into a grounding-type power outlet. This too, is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.

12. POWER-CORD PROTECTION

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.

13. LIGHTNING

To protect your unit from a lightning stor m, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit due to lightning and power line surges.

PORTABLE CART WARNING

(symbol provided by RETAC)

S3126A

Introduction

IMPORTANT SAFEGUARDS

14. POWER LINES

An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall onto or against such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits, as contact with them might be fatal.

15. OVERLOADING

Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.

16. OBJECT AND LIQUID ENTRY

Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.

17. OUTDOOR ANTENNA GROUNDING

If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges, Section 810 of the National Electrical Code (NEC), ANSI/NFPA 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

18. SERVICING

Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. For example: a. When the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the unit. c. If the unit has been exposed to rain or water. d. If the unit does not operate normally by following the operating instructions. Adjust only those controls

that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the unit to its

normal operation. e. If the unit has been dropped or the cabinet has been damaged. f. When the unit exhibits a distinct change in performance, this indicates a need for service.

19. REPLACEMENT PARTS

When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.

20. SAFETY CHECK

Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to determine that the unit is in proper operating condition.

21. WALL OR CEILING MOUNTING

The product should be mounted to a wall or ceiling only as recommended by the manufacturer.

22. HEAT

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

23. DISC TRAY

Keep your fingers well clear of the disc tray as it is closing. It may cause serious personal injury.

24. CONNECTING

When you connect the product to other equipment, turn off the power and unplug all of the equipment from the wall outlet. Failure to do so may cause an electric shock and serious personal injury. Read the owner's manual of the other equipment carefully and follow the instructions when making any connections.

25. LASER BEAM

Do not look into the opening of the disc tray or ventilation opening of the product to see the source of the laser beam. It may cause sight damage.

26. DISC

Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious personal injury and product malfunction.

IMPORTANT SAFEGUARDS / Power Source

27. NOTE TO CATV SYSTEM INSTALLER

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

EXAMPLE OF ANTENNA GROUNDING AS PER THE

NATIONAL ELECTRICAL CODE

ANTENNA LEAD IN WIRE

Introduction

GROUND CLAMP

ELECTRIC SERVICE

EQUIPMENT

NEC-NATIONAL ELECTRICAL CODE S2898A

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS POWER SERVICE GROUNDING

ELECTRODE SYSTEM (NEC ART 250, PART H)

IMPORTANT RECYCLING INFORMATION

This product uses both Cathode Ray Tube (CRT) and other components that contain lead. In your community there might be regulations that require you to dispose these materials properly under environmental considerations. Please contact your local authorities, or the Electronic Industries Alliance (http://www.eiae.org) for disposal or recycling information.

Power source

AC Outlet

Wider Hole and Blade

Polarized AC Cord Plug (One blade is wider than the other.)

TO USE AC POWER SOURCE

Use the AC polarized line cord provided for operation on AC. Insert the AC cord plug into a standard 120V 60Hz polarized AC outlet.

Notes:

Never connect the AC line cord plug to other than the specified

• voltage (120V 60Hz). Use the attached power cord only.

If the polarized AC cord does not fit into a non-polarized AC

• outlet, do not attempt to file or cut the blade. It is the user’s responsibility to have an electrician replace the obsolete outlet.

If you cause a static discharge when touching the unit and the

• unit fails to function, simply unplug the unit from the AC outlet

and plug it back in. The unit should return to normal operation. If the AC cord plug is plugged in for the first time, wait for about 5

• seconds before pressing the power button on the front panel.

Introduction

Precautions

Notes on handling

When shipping the unit, the original shipping carton and packing materials come in handy. For maximum protection, repack the unit as it was originally packed at the factory. Do not use volatile liquids, such as insect spray, near the unit. Do not leave rubber or plastic products in contact with the unit for a long time. They will leave marks on the finish. The top and rear panels of the unit may become warm after a long period of use. This is not a malfunction. When the

unit

is not in use, be sure to remove the disc and the video cassette turn off the power. If you do not use the unit for a long period, the unit may not function properly in the future. Turn on and use the unit occasionally.

Notes on locating

Place the unit on a level surface. Do not use it on a shaky or unstable surface such as a wobbling table or inclined stand. The loaded disc or the video tape may come off the proper position and cause damage to the unit. When you place this unit near a TV, radio, or VCR, the playback picture may become poor and the sound may be distorted. In this case, place the unit away from the TV, radio, or VCR.

Notes on moisture condensation

Moisture condensation damages the unit. Please read the following carefully.

Moisture condensation occurs, for example, when you pour a cold drink into a glass on a warm day. Drops of water form on the outside of the glass. In the same way, moisture may condense on the head drum or the optical pick-up lens inside this unit, one of the most crucial internal parts of the unit.

Moisture condensation occurs during the following cases.

When you bring the unit directly from a cold place to a warm place. When you use the unit in a room where you just turned on the heater, or a place where the cold wind from the air conditioner directly hits the unit. In summer, when you use the unit in a hot and humid place just after you move the unit from an air conditioned room. When you use the unit in a humid place.

Tape

Head drum

Notes on cleaning

Use a soft, dry cloth for cleaning.

For stubborn dirt, soak the cloth in a weak detergent solution, wring well and wipe. Use a dry cloth to wipe it dry. Do not use any type of solvent, such as thinner and benzine, as they may damage the surface of the unit. If you use a chemical saturated cloth to clean the unit, follow that product’s instructions.

To obtain a clear picture

The unit is a high technology, precision device. If the video head, the head drum, the optical pick-up lens and disc drive parts are dirty or worn down, the picture quality becomes poor. To obtain a clear picture, we recommend regular inspection and maintenance (cleaning or parts replacement) every 1,000 hours of use depending on the operating environment. For details, contact your nearest dealer.

Do not use the unit when moisture condensation may occur.

If you use the unit in such a situation, it may damage discs and internal parts. Remove the disc or the video tape, connect the power cord of the unit to the wall outlet, turn on the unit, and leave it for two or three hours. After two or three hours , the unit will have warmed up and evaporated any moisture. Keep the unit connected to the wall outlet and moisture condensation will seldom occur.

Wait!

Wall outlet

Notes on discs

On handling discs

Do not touch the playback side of the disc.

Playback side

Do not attach paper or tape to discs.

On cleaning discs

Fingerprints and dust on the disc cause picture and sound deterioration. Wipe the disc from the center outwards with a soft cloth. Always keep the disc clean.

Structure of disc contents

Normally, DVD video discs are divided into titles, and the titles are sub-divided into chapters. Video CDs and Audio CDs are divided into tracks.

DVD video disc

Title 1 Title 2

Chapter 1 Chapter 2 Chapter 1 Chapter 2 Chapter 3

Video CD/Audio CD

Track 1 Track 2 Track 3 Track 4 Track 5

Each title, chapter or track is assigned a number, which is called “title number”, “chapter number” or “track number” respectively. There may be discs that do not have these numbers.

Introduction

If you cannot wipe off the dust with a soft cloth, wipe the disc lightly with a slightly moistened soft cloth and finish with a dry cloth. Do not use any type of solvent such as thinner, benzine, commercially available cleaners or antistatic spray for vinyl LPs. It may damage the disc.

On storing discs

Do not store discs in a place subject to direct sunlight or near heat sources. Do not store discs in places subject to moisture and dust such as a bathroom or near a humidifier. Store discs vertically in a case. Stacking or placing objects on discs outside of their case may cause warping.

Notes on copyright

It is forbidden by law to copy, broadcast, show, broadcast on cable, play in public, and rent copyrighted material without permission.

This device does not tape-record copy protected DVD Video Discs. The device is not to be used for copying copyrighted content without the express written permission of the copyright owner. Obtaining such permission is the sole responsibility of the user.

This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

Introduction

Notes on discs (continued)

About this owner’s manual

This owner’s manual explains the basic instructions of this unit. Some DVD video discs are produced in a manner that allows specific or limited operation during playback. As such, the unit may not respond to all operating commands. This is not a defect in the unit. Refer to instruction notes of discs.

“

” may appear on the TV screen during operation.

A “

” means that the operation is not permitted by the unit or the disc at the moment. For example, it is unable to stop the playback of copyright message of the disc when the STOP ( ) button is pressed. Alternatively, the “

” may also

indicate that the feature is not available for the disc.

Notes on region numbers

The region number of this unit is 1. If region numbers, which stand for their playable area, are printed on your

ALL

DVD video disc and you do not find

, disc playback will not be allow ed by the player. (In this case, the unit will display a message on-screen.)

On Video CDs

This unit supports Video CDs equipped with the PBC (Version 2.0) function. (PBC is the abbreviation of Playback Control.) You can enjoy two playback variations depending on types of discs.

• Video CD not equipped with PBC function

(Version 1.1)

Sound and movie can be played on this unit in the same way as an audio CD.

• Video CD equipped with PBC function

(Version 2.0)

In addition to operation of a Video CD not equipped with the PBC function, you can enjoy playback of interactive software with search function by using the menu displayed on the TV screen (Menu Playbac k). Some of the functions described in this owner’s manual may not work with some discs.

Playable discs

This unit can play the following discs.

Audio

Video

Audio

Disc

Size

12 cm

8 cm

12 cm

8 cm

12 cm

8 cm

(CD

single)

Disc Mark

DVD video discs

Video CDs

Audio CDs

The following discs are also available.

CD-R/RW discs recorded by CD-DA method can be played. Some CD-R/RW discs may be incompatible.

DIGITAL VIDEO

CD-R CD-RW

Contents

(moving

pictures)

Audio Video

(moving

pictures)

• You cannot play discs other than those listed above.

• You cannot play discs of DVD-RAM, DVD-RW, etc., or non standardized discs even if they may be labeled as above.

• This unit uses the NTSC color system, and cannot play DVD video discs recorded in any other color system (PAL, SECAM, etc.).

Maximum

playback time

Approx. 4 hours

(single sided disc)

Approx. 8 hours

(double sided disc)

Approx. 80 minutes

(single sided disc)

Approx. 160 minutes

(double sided disc)

Approx. 74 minutes

Approx. 20 minutes

Approx. 74 minutes

Approx. 20 minutes

Introduction

IMPORTANT SAFEGUARDS ..........................2

Power source ...................................................5

Precautions ......................................................6

Notes on discs..................................................7

Contents........................................................... 9

Identification of Controls.................................10

Connections

Antenna connections......................................14

Cable TV connections ....................................15

Connecting to optional equipment..................16

Basic setup

Setting the language ......................................19

Clock setting................................................... 20

TV operation

TV operation................................................... 23

Tuner setting .................................................. 26

Setting the V-Chip .......................................... 28

To set the on timer.......................................... 31

To set the off timer.......................................... 32

Picture control adjustment.............................. 33

Sound control adjustment .............................. 34

Playback (VCR)

Loading and unloading a cassette tape ......... 35

Cassette tape playback.................................. 36

Special playback ............................................ 37

Convenient function ....................................... 38

Basic playback (DVD)

Preparation..................................................... 49

Playback procedure ....................................... 50

Special playback ............................................ 51

Advanced playback (DVD)

Zooming/Locating desired scene ................... 52

Repeat, Random and Program playback/

Repeat A-B..................................................... 53

Changing soundtrack language/Subtitles....... 54

Changing angles/Title selection/DVD menu... 55

Function setup (DVD)

Setting language ............................................ 56

Setting the aspect ratio of TV screen/

Setting on screen display ............................... 57

Dynamic Range Control ................................. 58

Parental control setting .................................. 59

To change the parental level .......................... 60

Temporary disabling of rating level

by DVD disc ................................................... 61

Others

Before calling service personnel .................... 62

Reception disturbances.................................. 64

Language code list .........................................65

Specifications ................................................. 66

Limited warranty............................................. 67

Introduction

Recording (VCR)

Recording a TV program ................................ 40

One-touch Timer Recording (OTR) ................ 42

Timer recording.............................................. 43

Other functions (VCR)

Setting the surround sound/

Setting the stable sound................................. 45

Second Audio Program (SAP)/

Stereo recording and playback ...................... 46

Duplicating a video tape................................. 47

Recording a DVD/CD disc.............................. 48

Introduction

Identification of Controls

See the page in for details.

Front panel

AUDIO

VIDEO

LINE IN 2

HEADPHONE jack

Cassette Loading Slot

PHONES L/MONO R REW PLAY FF REC/OTR CHANNEL OPEN/CLOSE VOLUME SKIP STOP PLAY SKIP

Remote sensor

STOP/EJECT

AUDIO

PHONES L/MONO R REW PLAY FF REC/OTR CHANNEL OPEN/CLOSE VOLUME SKIP STOP PLAY SKIP

STOP/EJECT

VIDEO

POWER REC/OTRTIMER REC

LINE IN 2

TIMER REC indicator

POWER REC/OTR TIMER REC

POWER

Disc tray

POWER

POWER button

AUDIO (L/R)/VIDEO IN (LINE IN 2) jacks

REW (Rewind) button

STOP/EJECT button

PLAY button

FF (Fast Forward) button

REC/OTR button

CHANNEL ▲/▼ buttons

Rear panel

RF IN (UHF/VHF) jack

36 35

36 36 40 24

POWER indicator

VHF/UHF

REC/OTR

indicator

OUT PUT

VHF/UHF

VIDEO

DIGITAL AUDIO

COAXIAL

AUDIO

DIGITAL AUDIO

COAXIAL

LINE 1 IN

VIDEO

(MONO)

AUDIO R

OUT PUT

VIDEO

AUDIO

LINE 1 IN

VIDEO

(MONO)

AUDIO

SKIP button PLAY button STOP button SKIP button

VOLUME ▲/▼ buttons OPEN/CLOSE button

AC power cord

BITSTREAM/PCM COAXIAL

AUDIO OUT jack

AUDIO(L/R)/VIDEO

OUT jacks

AUDIO (L/R)/VIDEO IN (LINE 1 IN) jacks

TV/VCR operation status

Press DISPLAY to display the information on the screen. To cancel the display, press DISPLAY again.

While watching TV While operating a tape

TV/VCR

Clock

Stereo and

second audio

program

Day of the week

TV/VCR

8:47

MON

STEREO SAP

00 : 00 : 00 SP

CH 125

Channel

Hi-Fi stereo

TV/VCR

8 : 30

MON

HI-FI

00 : 15 : 12 SP

Real time tape counter

CH 125

DVD/Audio CD/Video CD operation status

DVD

Audio CD/Video CD

VCR operation*

Auto repeat Tape in

Tape speed

VCR operation*

Recording :

Rec/Pause

Play :

Fast-forward :

Rewind :

Stop :

Eject :

Introduction

Press DISPLAY to display the information on the screen. To cancel the display, press DISPLAY again.

Title number Title elapsed playing time

Disc operation

Chapter number

1/8

1/19

1/8Eng DolbyDigital

Audio language

A kind of audio

Title total time

0:07:18 2:02:31

Subtitle language

1/8 Eng

1/1

Camera angle

When you play the CD disc, the status display will appear on the screen and continue displaying.

PBC (PlayBack Control) on Video CD

Track elapsed playing time

Disc operation Track number

Play list

PBC 1 / 8

0:02:31 0:53:09

Playlist 1 2 3 4 5 6 7 8

Track total time

Notes: • When you play the Video CD, Play list will not appear

on the screen.

• To turn off the PBC, press Number button 1 in the stop mode, then press ENTER.

Introduction

Identification of Controls (continued)

The instructions in this manual describe the functions on the remote control. See the page in for details.

Remote control

DVD button TV/VCR button

Direct channel selection buttons

Number buttons

DISPLAY button SLEEP button

23 28

AUDIO SELECT button REC buttons

TIMER REC buttons

button

36 36

button

PLAY button REV button

CM SKIP button JUMP button

COUNTER RESET ANGLE

SP/SLP RETURN

MENU SETUP

Direction buttons

( / / / )

CANCEL CLEAR

button

DVDTV/VCR

POWER

321

CHANNEL

654

DISPLAY

AUDIO

SLEEP

SELECT

TIMER

REC

CM SKIP/JUMP

COUNTER

RESET

RETURN

ANGLE

SETUP

ENTER

CANCEL

CLEAR

PLAY

STOP

VOLUMEMUTE

CHANNEL

CLOSED

RETURN

CAPTION

SKIP

REC

FWDREV

PAUSE/STILL

ZERO

INPUT

RETURN

SELECTSP/SLP

SUBTITLE

ZOOM

PROGRAM

D.TRACKING

REPEAT A-B TOP MENU

DVD MENU

PLAY MODE

TRK

SLOW

POWER button

CHANNEL / buttons

MUTE button

VOLUME / buttons

CLOSED CAPTION button

SKIP button SLOW button

CHANNEL RETURN button SKIP button

STOP button FWD button

PAUSE/STILL button ZERO RETURN button

SUBTITLE button PROGRAM button

REPEAT A-B button INPUT SELECT button

ZOOM button D.TRACKING button TOP MENU button

TRK + button DVD MENU button*

TRK - button PLAY MODE button ENTER button

* DVD MENU button

Use the MENU button to display the menu included on many DVD video discs . To oper ate a menu, follow the instructions in “DVD menu”.

Inserting Batteries

Introduction

Slide the battery compartment cover in the direction of the

arrow.

Battery precautions:

The precautions below should be followed when using batteries in this device:

1.Use only the size and type of batteries specified.

2.Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. versed batteries may cause damage to the device. To avoid a potential shor t circuit, insert the “–” end first.

Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.

4.If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.

5.Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. (Follow battery manufacturer’s directions.)

Install two “AAA” batteries (supplied),

polarity diagram in the battery compartment.

paying attention to the

Replace the compartment cover.

Re-

Remote control basics

• Press POWER to turn the unit on or off.

• Select your desired operating mode (TV/VCR or DVD) using TV/VCR or DVD.

• Tap CH

• The Direction buttons (

• You can directly access specific channels using Direct channel selection buttons.

or CH to move through the channels one channel at a time.

/ / / ) are also used to navigate on-screen menu system.

Operation:

• Aim the remote control at the remote sensor and press control buttons to

operate.

• Operate the remote control within 30° angle on either side of the remote

sensor, up to a distance of Approx. 7 meters.

Approx. 7 meters

Connections

Antenna connections

If you are using an indoor or outdoor antenna, follow the instructions below that correspond to your antenna system. If you are using a cable TV service (CATV), see page 15 for Cable TV connections.

Combination VHF/UHF Antenna (Single 75 ohm Cable or 300 ohm Twin-lead Wire)

Connect the 75 ohm Cable from the Combination VHF/UHF Antenna to the Antenna Jack.

75 ohm Coaxial Cable

Antenna

Jack

300-75 ohm Matching Transformer

Antenna

Jack

If your Combination VHF/UHF Antenna has a 300 ohm Twin-lead Wire, the use of the 300-75 ohm Matching Tr ansformer may be necessary.

Combination VHF/UHF Antenna (Separate VHF and UHF 300 ohm Twin-lead Wires)

Connect the UHF 300 ohm Twin-lead Wire to the

Antenna

Jack

Combiner

UHF 300 ohm

300-75 ohm Matching Transformer

VHF 300 ohm

Combiner (not supplied). Connect the VHF 300 ohm Twin-lead Wire to the 300-75 ohm Matching Transformer. Attach the Transformer to the Combiner, then attach the Combiner to the Antenna Jack.

Separate VHF/UHF Antennas (75 ohm VHF Cable and 300 ohm UHF Twin-lead Wires)

Connect the VHF 75 ohm cable and UHF 300 ohm Twinlead Wire to the Combiner (not supplied). Attach the

Antenna

Jack

VHF 75 ohm

Combiner to the Antenna Jack.

Combiner

UHF 300 ohm

Cable TV Connections

This unit has an extended tuning range and can tune most cable channels without using a Cab le TV Converter box. Some cable companies offer “premium pay channels” in which the signal is scrambled. Descrambling these signals for normal viewing requires the use of a descrambler device which is generally provided by the cable company.

For subscriber to basic cable TV service

For basic cable service not requiring a Converter/Descrambler box,

Antenna

Jack

75 ohm Coaxial Cable

For subscriber to scrambled cable TV service

If you subscribe to a cable TV service which requires the use of a Converter/Descrambler box, connect the incoming 75 ohm Coaxial Cable to the Converter/Descrambler box. Using another 75 ohm Coaxial Cable, connect the output jack of the Converter/Descrambler box to the Antenna Jack on the unit. Follow the connections shown below. Tune the unit to the output channel of the Converter/Descrambler box (usually channel 3 or 4) and use the Converter/Descrambler box to select channels.

connect the CATV 75 ohm Coaxial Cable directly to the Antenna Jack on the back of the unit.

Connections

Incoming 75 ohm CATV Cable

Converter/

Descrambler

75 ohm Cable to the unit

Antenna

Jack

For subscribers to unscrambled basic cable TV service with scrambled premium channels

If you subscribe to a cable TV service in which basic channels are unscrambled and premium channels require the use of a Converter/Descrambler box, you may wish to use a signal Splitter and an A/B Switch box (available from the Cable company or an electronics supply store). Follow the connections shown below. With the switch in the “B” position, you can directly tune any nonscrambled channels on your unit. With the switch in the “A” position, tune your unit to the output of the Converter/ Descrambler box (usually channel 3 or 4) and use the Converter/Descrambler box to tune scrambled channels.

Incoming 75 ohm CATV Cable

Splitter

Converter/

Descrambler

A/B Switch

75 ohm Cable

to the unit

Antenna

Jack

Connections

Connecting to optional equipment

Before connecting the unit to other equipment, be sure to turn off the power and unplug all of the equipment from the wall outlet before making any connections. You can enjoy the TV game, camcorder or high quality dynamic sounds of DVD video discs or audio CDs by connecting the unit to optional audio equipment.

Connecting a camcorder or a TV game

Select “LINE 2” using the INPUT SELECT button.

Signal flow

Camcorder

To AUDIO (L/R)/VIDEO OUT

(yellow)

(white)

AUDIO

STOP/EJECT

PHONES L/MONO R REW PLAY FF REC/OTR CHANNEL OPEN/CLOSE VOLUME SKIP STOP PLAY SKIP

VIDEO

LINE IN 2

POWER REC/OTR TIMER REC

To AUDIO (L/R)/VIDEO IN

POWER

(LINE IN 2)

Audio/Video cable (not supplied)

(yellow)

(white)

(red)

TV GAME

(red)

Connecting to an audio system

Connect the unit to your audio system.

Audio system

VHF/UHF

DIGITAL AUDIO

To ANALOG AUDIO OUT

LINE 1 IN

OUT PUT

VIDEO

(MONO)

COAXIAL

AUDIO

Audio cable (not supplied)

(white)

(red)

To audio inputs of the amplifier

Notes:

• Refer to the owner’s manual of the connected equipment as well.

• If you place the unit near a tuner or radio, the radio broadcast sound might be distorted. In this case, place the unit away from the tuner and radio.

• The output sound of the unit has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate listening level. Otherwise, the speakers may be damaged by a sudden high volume sound.

• Turn off the amplifier before y ou connect or disconnect the unit’s power cord. If you leave the amplifier power on, the speakers may be damaged.

: Front speaker : Rear speaker

: Center speaker : Signal flow

: Sub woofer

Connecting to an amplifier equipped with a Dolby Digital decoder

Dolby Digital

Dolby Digital is the surround sound technology used in theaters showing the latest movies, and is now available to reproduce this realistic effect in the home. You can enjoy motion picture and live concert DVD video discs with this dynamic realistic sound by connecting the unit to a 6 channel amplifier equipped with a Dolby Digital decoder or Dolby Digital processor. If you have a Dolby Pro Logic Surround decoder, you will obtain the full benefit of Pro Logic from the same DVD movies that provide full 5.1 channel Dolby Digital soundtracks, as well as from titles with the Dolby Surround mark.

Manufactured under license from Dolby

Amplifier equipped with a Dolby Digital decoder

To COAXIAL type digital audio input

75 Ω coaxial cable

LINE 1 IN

OUT PUT

VHF/UHF

VIDEO

DIGITAL AUDIO

(MONO)

COAXIAL

AUDIO

AUDIO R

• Use DVD video discs encoded via the Dolby Digital recording system.

Connecting to an amplifier equipped with Dolby Pro Logic Surround

Dolby Pro Logic Surround

You can enjoy the dynamic realistic sound of Dolby Pro Logic Surround by connecting an amplifier and speaker system (right and left front speakers, a center speaker, and one or two rear speakers).

With an amplifier equipped with Dolby Digital Connect the equipment the same way as described in “Connecting to an amplifier equipped with a Dolby Digital decoder.” Refer to that amplifier’s owner’s manual and set the amplifier so you can enjoy Dolby Pro Logic Surround sound.

With an amplifier not equipped with Dolby Digital Connect the equipment as follows.

Connections

Amplifier equipped with Dolby Pro Logic Surround

LINE 1 IN

OUT PUT

VHF/UHF

VIDEO

DIGITAL AUDIO

(MONO)

COAXIAL

AUDIO

To audio input

T o ANALOG AUDIO OUT

Audio cable

* Connect one or two rear speakers. The output sound from the rear speakers will be monaural even if you connect two rear speakers.

Connecting to an amplifier equipped with a DTS decoder

Digital Theater Systems (DTS)

DTS is a high quality surround technology used in theaters and now available for home use, on DVD video discs or audio CDs. If you have a DTS decoder or processor, you can obtain the full benefit of 5.1 channel DTS encoded sound tracks on DVD video discs or audio CDs.

Amplifier equipped with a DTS decoder

To COAXIAL type digital audio input

75 Ω coaxial cable

LINE 1 IN

OUT PUT

VHF/UHF

VIDEO

DIGITAL AUDIO

(MONO)

COAXIAL

AUDIO

“DTS” and “DTS Digital Surround” are trademarks of Digital Theater Systems, Inc.

• Use DVD video discs or audio CDs encoded via the DTS recording system.

Connections

Warning:

When playing DTS-encoded discs (unit), excessive noise may be output from the analog stereo jacks. To avoid possible damage to the audio system, you should take proper precautions when the ANALOG AUDIO OUT (L/R) jacks of the unit are connected to an amplification system. To enjoy DTS Digital Surround™ playback, an external 5.1 channel DTS Digital Surround™ decoder system must be connected to the BITSTREAM/PCM AUDIO OUT jack of the unit.

Connecting to an amplifier equipped with an MPEG2 audio decoder

MPEG2 sound

You can enjoy motion picture and live concert DVD video discs with dynamic realistic sound by connecting an amplifier equipped with an MPEG2 audio decoder or MPEG2 audio processor.

• Use DVD video discs encoded via

Amplifier equipped with an MPEG2 audio decoder

To COAXIAL type digital audio input

75 Ω coaxial cable

LINE 1 IN

OUT PUT

VHF/UHF

VIDEO

DIGITAL AUDIO

(MONO)

COAXIAL

AUDIO

AUDIO R

the MPEG2 recording system.

Connecting to an amplifier equipped with a digital audio input

2 channel digital stereo

You can enjoy the dynamic sound of 2 channel digital stereo by connecting an amplifier equipped with a digital audio input and speaker system (right and left front speakers).

Amplifier equipped with a digital audio input

To COAXIAL type digital audio input

75 Ω coaxial cable

Notes:

• DO NOT connect the BITSTREAM/PCM AUDIO OUT jack of the unit to the AC-3 RF input of a Dolby Digital Receiver. This input on your A/V Receiver is reserved for Laserdisc use only and is incompatible with the BITSTREAM/PCM AUDIO OUT jack of the unit.

• Connect the BITSTREAM/PCM AUDIO OUT jack of the unit to the “COAXIAL” input of a Receiver or Processor.

• Refer to the owner’s manual of the connected equipment as well.

• When you connect the unit to other equipment, be sure to turn off the power and unplug all of the equipment from the wall outlet before making any connections.

• Turn off the amplifier before y ou connect or disconnect the unit’s power cord. If you leave the amplifier power on, the speakers may be damaged.

LINE 1 IN

OUT PUT

VHF/UHF

VIDEO

DIGITAL AUDIO

(MONO)

COAXIAL

AUDIO

AUDIO R

Basic setup

ENTER

Setting the language

This unit can display the on screen language in English, Spanish or French. Language selection (step 3) will automatically appear on the screen when you press MENU initially. Select the language you prefer first, then proceed with the other menu options.

Setting the language

TV/VCR POWER

1-3 1,4

1-3

Preparation:

• Press POWER to turn on the unit.

• Press TV/VCR to select the TV/VCR mode.

Press MENU. Press SETUP”, then press ENTER.

SETUP

Press or to select “LANGUAGE”, then press ENTER.

or to select “SYSTEM

M E N U TIMER REC SET TV SETUP CH SETUP AUTO REPEAT ON OFF SYSTEM SETUP

〈

/ /ENTER/MENU

SYSTEM SETUP CLOCK SET LANGUAGE/IDIOMA/LANGUE AUTO CLOCK ON OFF STANDARD TIME DAYLIGHT SAVING TIME

〈

/ /ENTER/MENU

Notes:

• Both the TV/VCR and the DVD have their own menu option

• If no buttons are pressed for more than 60 seconds, the TV/VCR MENU screen will return to normal TV operation automatically.

〉

Basic setup

Press or to select the desired language: English (ENGLISH), Spanish (ESPAÑOL) or

French (FRANCAIS), then press ENTER.

LANGUAGE/IDIOMA/LANGUE

/ /ENTER/MENU

Press MENU repeatedly until the MENU screen is cleared.

SETUP

ENGLISH ESPAÑOL FRANCAIS

Basic setup

SYSTEM SETUP CLOCK SET LANGUAGE/IDIOMA/LANGUE AUTO CLOCK ON OFF STANDARD TIME DAYLIGHT SAVING TIME

〈

/ /ENTER/MENU

〉

M E N U TIMER REC SET TV SETUP CH SETUP AUTO REPEAT ON OFF SYSTEM SETUP

〈

/ /ENTER/MENU

〉

Clock setting

The Auto Clock function will automatically set the built-in clock (Month, Day, Year and Time) when the unit is connected to an Antenna or Cable system and it is turned off. As the unit searches for a receivable station in your area and it receives a broadcast signal for Auto Clock, the Auto Clock needs several minutes to set itself.

Auto Clock setting

Preparation:

• Connect the Antenna or Cable system.

• If you use a cable box, turn it on.

• Plug the AC Power cord to the AC outlet.

Make sure the unit is turned off.

POWER

Wait at least three minutes and press POWER.

POWER

• If you press POWER , the Auto Clock set is not effective.

The POWER indicator will light.

POWER

To set Auto Clock to OFF

When shipped from factory the AUTO CLOCK is set to “ON”. But if you do not want Auto Clock set (Adjustment):

POWER DISPLAY

2,3

1,5

2,4

Press MENU.

SETUP

Press or to select “SYSTEM SETUP”, then press ENTER.

ENTER

M E N U TIMER REC SET TV SETUP CH SETUP AUTO REPEAT ON OFF SYSTEM SETUP

〈

/ /ENTER/MENU

〉

Press DISPLAY to check the clock on the screen.

If the clock is not set, check the antenna condition. The Auto Clock may not function

properly if the reception condition is not good.

Auto Clock adjustment

The Auto Clock adjustment will be performed at 12:00 PM everyday if you turn off the unit.

• If you use a cable box and you want Auto Clock adjustment to be performed, the cable box must be left on.

• The Auto Clock adjustment is not effective when there is a difference of more than 5 minutes exists between the built-in clock time and the actual time.

DISPLAY

TV/VCR

8:47

STEREO SAP

MON

CH 125

00 : 00 : 00 SP

Press or to select “AUTO CLOCK”.

ENTER

Press ENTER to select “OFF”.

ENTER

Press MENU repeatedly until the MENU screen is cleared.

SETUP

• When the AUTO CLOCK is set to “OFF”, the Auto Clock adjustment does not function.

• Set the clock manually 22.

SYSTEM SETUP CLOCK SET LANGUAGE/IDIOMA/LANGUE AUTO CLOCK ON OFF STANDARD TIME DAYLIGHT SAVING TIME

〈

/ /ENTER/MENU

〉

ENTER

SETUP

To set standard time

ENTER

SETUP

To set daylight saving time

In the rare event that you live within broadcast range of two stations in two different time zones, the unit may recognize the wrong station for the Auto Clock set. To correct the situation:

Press MENU.

SETUP

M E N U TIMER REC SET TV SETUP CH SETUP AUTO REPEAT ON OFF SYSTEM SETUP

〈

/ /ENTER/MENU

〉

Press or to select “SYSTEM SETUP”, then press ENTER.

M E N U TIMER REC SET TV SETUP CH SETUP AUTO REPEAT ON OFF SYSTEM SETUP

Press

then press ENTER.

〈

/ /ENTER/MENU

to select “STANDARD TIME”

SYSTEM SETUP CLOCK SET LANGUAGE/IDIOMA/LANGUE AUTO CLOCK ON OFF STANDARD TIME DAYLIGHT SAVING TIME

〈

/ /ENTER/MENU

〉

Press or to select your time zone, then press ENTER.

ATLANTIC : GMT–4hours EASTERN : GMT–5hours CENTRAL : GMT–6hours MOUNTAIN : GMT–7hours PACIFIC : GMT–8hours ALASKA : GMT–9hours HAWAII : GMT–10hours AUTO : AUTO SET (GMT: Greenwich Mean Time)

You can set the Daylight saving time automatically or manually .

Press MENU. Press

then press ENTER.

or to select “SYSTEM SETUP”,

M E N U TIMER REC SET

ENTER

TV SETUP CH SETUP AUTO REPEAT ON OFF SYSTEM SETUP

〈

/ /ENTER/MENU

〉

Press or to select “DAYLIGHT SAVING TIME”, then press ENTER.

SYSTEM SETUP CLOCK SET

ENTER

LANGUAGE/IDIOMA/LANGUE AUTO CLOCK ON OFF STANDARD TIME DAYLIGHT SAVING TIME

〈

/ /ENTER/MENU

〉

Press or to select one of the options, then press ENTER.

DAYLIGHT SAVING TIME

ENTER

ON: OFF: AUTO:

When you want to set the Daylight Saving Time manually, on the first Sunday in April you set to “ON”, and on the last Sunday in October you set to “OFF”.

for manual setting (forward one hour) for manual setting (back one hour) for automatic setting (read XDS in the signal)

ON OFF AUTO

〈

/ /ENTER/MENU

〉

Press MENU repeatedly until the MENU screen is cleared.

Basic setup

Press MENU repeatedly until the MENU screen is cleared.

SETUP

Note:

To be able to select the standard time, the clock must first be set by “AUTO CLOCK” once.

Notes:

• When shipped from factory, the DAYLIGHT SAVING TIME is

set to “AUTO” position.

• When the clock is not set, Daylight Saving Time setting is not available.

• When there is no Daylight Saving Time in your area, always select “OFF” position in step 3.

+ 47 hidden pages