CE Compliance ....................................................................................30
Working Environment ...........................................................................30
Additional Environments not Related to EMC ......................................31
Following information is only for EU-member states: ...........................31
Disposal of Products .......................................................................31
Disposal of Batteries and/or Accumulators .....................................32
User’s ManualEN-3
Conventions
DANGER
WARNING
CAUTION
CAUTION
NOTE
This manual uses the following formats to describe, identify, and highlight
terms and operating procedures.
Abbreviations
On first appearance, and whenever necessary for clarity, abbreviations are
enclosed in parentheses following their definition. For example: Read Only
Memory (ROM).
Icons
Icons identify ports, dials, and other parts of your product. The indicator
panel also uses icons to identify components.
Safety Icons
This guide contains safety instructions that must be observed to avoid
potential hazards that could result in personal injuries,damage to your
equipment, or loss of data. These safety cautions have been classified
according to the seriousness of the risk, and icons highlight these
instructions as follows:
Signal WordsMeaning
Indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.
Indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
Indicates a potentially hazardous situation which, if not
avoided, may result in minor injury or moderate injury.
Indicates a potentially hazardous situation which, if not
avoided, may result in property damage.
Provides important information.
EN-4User’s Manual
Introduction
Welcome and thank you for choosing a TOSHIBA product.
For your convenience, your TOSHIBA product is furnished with two guides:
n Quick Start Guide
n comprehensive User’s Manual (pre-installed on Journe album)
Checking the components
Journe AlbumUSB CableAC Adaptor
USB Host CableQuick Start Guide
(printed) & User’s
Manual (pre-installed
on Journe album)
User’s ManualEN-5
Warranty Leaflet
Safety Instructions
WARNING
Always read the safety instructions carefully:
Do not disassemble, modify, tamper with or repair your product
n Do not attempt to disassemble, modify, tamper with or repair product
(including AC adaptor). Disassembly, modification, tampering or
repairing the product could cause fire or electric shock, possibly
resulting in serious injury.
Please contact an authorized Toshiba service provider for any repair
service.
Handling the AC adaptor and power cables/cords or plugs
n When handling the power cable/cord, follow these precautions:
n Never tamper with the power cable/cord or plug.
n Never splice or alter a power cable/cord.
n Never bend or twist a power cable/cord.
n Never pull on a power cable/cord to remove a plug from a socket.
Always grasp the plug directly.
n Never place heavy objects on a power cable/cord.
n Never run a power cable/cord through a pinch point such as a door
or window.
n Never place a power cable/cord near a heat source.
n Never use nails, staples or similar objects to fasten or attach cord in
place.
n Never attempt to disassemble or repair an AC adaptor.
Doing any of the above may damage the cables, and/or result in a
fire or electric shock, possibly resulting in serious injury.
Attaching the power cable/cord
n Always confirm that the power plug (and extension cable plug if used)
has been fully inserted into the socket, to ensure a secure electrical
connection. Failure to do so may result in a fire or electric shock,
possibly resulting in serious injury.
n Be careful if you use a multiple connector. An overload on one socket
could cause a fire or electric shock, possibly resulting in serious injury.
EN-6User’s Manual
Dust on the power plug connectors or connector base
n If dust gets on the power plug connectors or connector base, turn the
power off and disconnect the power plug. Then clean the connector and/
or connector base with a dry cloth. Continuing to use the product without
cleaning the power plug may result in a fire or an electric shock, possibly
resulting in serious injury.
Only use TOSHIBA AC adaptor
n Always use the TOSHIBA AC adaptor that was provided with your
product (that may have been provided with your product), or use AC
adaptors specified by TOSHIBA to avoid any risk of fire or other damage
to the product. Use of an incompatible AC adaptor could cause fire or
damage to the product possibly resulting in serious injury. TOSHIBA
assumes no liability for any damage caused by use of an incompatible
adaptor or charger.
Use correct power source
n Never plug the AC adaptor into a power source that does not
correspond to both the voltage and the frequency specified on the
regulatory label of the unit. Failure to do so could result in a fire or
electric shock, possibly resulting in serious injury.
Only use approved power cables/cords
n Always use or purchase power cables/cords that comply with the legal
voltage and frequency specifications and requirements in the country of
use. Failure to do so could result in a fire or electric shock, possibly
resulting in serious injury.
Do not handle the power plug with wet hands
n Never attempt to connect or disconnect a power plug with wet hands.
Failure to follow this instruction could result in an electric shock, possibly
resulting in serious injury.
Choking hazards
n Never leave small parts such as covers, caps and screws within the
reach of infants or small children. Swallowing a small part may cause
choking and suffocation resulting in death or serious injury. If a part is
swallowed, immediately take appropriate emergency action and consult
a doctor.
User’s ManualEN-7
Avoid liquids, moisture and foreign objects
n Never allow any liquids to spill into any part of your product, and never
expose the product to rain, water, seawater or moisture. Exposure to
liquid or moisture can cause electric shock or fire, resulting in damage or
serious injury. If any of these eventualities should accidentally occur,
immediately:
1. Turn off the product.
2. Disconnect the AC adaptor from the power plug socket and product.
Do not turn on the power again, until you have taken the product to an
authorized service center. Failure to follow these instructions could
result in serious injury or permanent damage to the product.
Never place your product or AC adaptor on a heat sensitive surface
n Never place your product or AC adaptor on a wooden surface, furniture,
or any other surface that could be marred by exposure to heat since the
product base and AC adaptor’s surface increase in temperature during
normal use.
n Always place your product or AC adaptor on a flat and hard surface that
is resistant to heat damage.
Never place your product in a damp environment
n Never use or place your product in a bathroom or any other damp
environment or in an outdoor environment or location where it may be
exposed to rain, mist, fog or other source of water or moisture. Such
exposure could cause a fire or electric shock, possibly resulting in
serious injury. It may also cause a computer failure, or loss of data.
Use the LCD correctly
n If the LCD (Liquid Crystal Display) panel is damaged, causing a liquid
crystal leak, never ingest or touch the liquid. Serious injury could result.
n If LCD liquid should accidentally contact your lips or mouth, always rinse
immediately with large amounts of water.
n If LCD liquid contacts your body, always use large amounts of water to
wash it off immediately to prevent skin rash.
n If LCD liquid should accidentally contact your eyes, always rinse them
immediately with large amounts of water, and obtain prompt medical
attention.
n If any of the LCD liquid contacts your clothes, remove them immediately
and wash with a synthetic detergent.
n Failure to follow these instructions may result in serious injury.
EN-8User’s Manual
n Never touch the LCD if it is damaged or broken, as the liquid contained
CAUTION
within the display may leak, possibly resulting in serious injury. Contact
an authorized Company service provider immediately for replacement of
the damaged LCD and dispose of any damaged LCD in compliance with
local laws and/or regulations.
Never place your product in locations with excess heat
n Never place your product where it will be exposed to excess heat, such
as in direct sunlight, an unventilated vehicle or near a heater. This may
result in a system failure, malfunction, loss of data or damage to the
product.
Never place your product in a location with extremely low
temperatures
n Never place your product in a location where it will be exposed to
extremely low temperatures. This may result in a system failure,
malfunction or loss of data.
Never subject your product to sudden temperature variations
n Never subject your product to sudden temperature variations. This may
result in condensation, causing a system failure, malfunction or loss of
data.
Never operate your product during a thunderstorm
n Never operate your product on AC power during a thunderstorm. If you
see lightning or hear thunder, immediately turn off the product. An
electric surge caused by the storm, may result in a system failure, loss
of data or hardware damage.
System Requirements
n Windows 2000/XP/Vista
n USB 2.0 interface
User’s ManualEN-9
The Grand Tour
LCD
Volume Up/Down or Zoom
In/Out
up/down/right/left/OK
ESC
MENU
Speaker
DC IN
Reset
Power
Front View
Control
Buttons
Operate the photo album by pressing the control
buttons on the front panel.
LCD also displays function icons for each button in the
corresponding position.
Bottom View
DC IN jackUsed to charge the digital album with the supplied
adapter.
Reset ButtonUsed to reset the digital album-press the Reset
button.
Power ButtonUsed to turn on the digital album-press the Power
button at the bottom of the display.
EN-10User’s Manual
Side View
card slot covers
A
B
SD/MMC/MS/MS-Pro
cards slot
CF card slotMini USB
Connector
NOTE
To use the card slot, please open the slot cover follow the illustrations as
displayed below.
The card slots will be displayed.
Mini USB
Connector
SD/MMC/MS/MSPro cards slot
CF card slotThis slot allows you to insert a Compact Flash (CF)
User’s ManualEN-11
This USB Connector connects the digital album to
your PC.
This slot allows you to insert the Secure Digital
(SD) /Multi Media Card (MMC)/Memory Stick (MS)/
Memory Stick Pro (MS-Pro) cards.
card.
Please note that not all memory media have been tested
and verified to work correctly. Therefore, it is not
possible to guarantee that all memory media will operate
properly.
Getting Started
Positioning the Unit
The digital album should be placed close to a power socket. Protect the unit
from high temperatures and high moisture levels.
Connecting to AC Power
1. Connect one end of the AC power adapter to the power jack at the
bottom of the album.
2. Connect the other end to a power outlet.
Turning on the Digital Album
Press the power button at the bottom of the display. The power LED will
light blue and the startup screen will appear as displayed below.
EN-12User’s Manual
If you are using the album for the first time,no albums
NOTE
NOTE
CAUTION
will be displayed. To copy photos to the unit’s internal
memory,please follow the instructions in the Copying
and Deleting Files section.
You can turn off the digital album by pressing the power button. It takes 2
seconds for the photo album to shut down.
Built-in battery
The digital album is equipped with a built-in lithium polymer battery. To
check the battery status, enter Setup mode and select Status.
To charge the battery, follow the steps below:
1. Connect one end of the AC power adapter to the power jack at the
bottom of the album.
2. Connect the other end to a power outlet.
3. Place the digital album on a stable surface, and keep power connected
until the battery is fully charged.
Please charge the battery for 8 hours before using for
the first time.
When the battery is running out of power, a warning
message will show on the screen and the album will shut
down automatically. Charge the battery as outlined
above.
The fully charged battery usually lasts about
2.5 hours,depending on use and settings.
Power system and plug types may vary depending on
your country/region.
Do not disassemble or modify the battery.
User’s ManualEN-13
Inserting/Removing a Memory Card
CAUTION
CAUTION
Inserting a Memory Card:
1. Insert your memory card into the slot on the side of the album with the
metal connectors facing down.
When inserting memory media, do not touch the metal
contacts. You could expose the storage area to static
electricity, which can destroy data.
2. Press the card gently until it clicks into place.
Removing a Memory Card
1. Press the memory card until it clicks and partially pops out of the slot.
2. Grasp the card and remove it.
Do not remove memory media while data is being
written or read. Wait for the operation to be completed.
For the detailed information, please refer to Copying and
Deleting Files section.
EN-14User’s Manual
USB Connection
album screen
The album can be connected to a PC using the supplied USB cable. The
PC will recognize the digital album as a mass storage device.
Once the digital album connects to a PC, it is not operable until it is
disconnected from the PC.
User’s ManualEN-15
Understanding the Menu Icons
The top left corner of the screen will display different icons for operation
depending on your use. These icons are defined as follows:
IconActions
Go to the browser screen in card (appears when CF card is
inserted). When selected, the icon is highlighted in orange.
Go to the browser screen in card (appears when SD/MMC/
MS/MS-Pro card is inserted).
Go to the browser screen in USB drive (appears when the
USB drive is inserted).
Delete files.
Setup.
Go to Slide Show screen.
Backup icon. Copy files from the memory card to the album.
Display volume level.
Theme
Screen Brightness
Language
EN-16User’s Manual
Date/Time
Album namedate createdpage number
Auto Shutdown Timer
Status
Basic Operations
Photo Mode
The Album screen is the digital album’s main screen. Folders in internal
memory are listed as albums. The first photo in each album is displayed as
a preview.
1. Select the album on the screen by pressing the up/down/left/right
button, followed by the OK button to enter the album.
User’s ManualEN-17
2. Select the photo you want to access, then press OK. The photo will be
displayed.
To rotate the photo, press the OK button on the album.
To display the photo information, press the MENU button on the album.
Pressing the MENU button again will hide photo information.
To enlarge the photo, press the Zoom In button. The photo will be
displayed in full screen mode. Users can view details of a photo by
zooming in.
EN-18User’s Manual
Music cannot be controlled while viewing photos. To
NOTE
adjust music settings, please press the ESC button to
return to the album screen.
Slide Show
You may use the slide show function to display the photos automatically.
In the album menu, press the MENU button to display the Slide Show icon,
then press OK button to activate it.
During the slide show, the OK button can be pressed at any time to pause.
The interval between photos can also be adjusted between 1-60 seconds
by pressing the Up/Down button on the album.
User’s ManualEN-19
The slide show function is not available in each photo
NOTE
screen.
Slide show cycles in a single album and will not proceed
to the next album.
Video files are skipped in slide shows.
To listen to the background music during a slide show, press the volume Up
button to turn on the music and volume. To pause the music, press the
Volume Down button repeatedly until the sound is off.
On reaching the end of the album, a page will be displayed, showing the
words “The End”.
EN-20User’s Manual
Video Mode
A video file is displayed with a video icon. Press the OK button to play the
video file.
Left/Right button----fast forward the video.
Up button----jump to the end and beginning-the OK button must be pressed
again to begin the video.
Down button----directly rewind to the beginning-the OK button must be
pressed again to play the video.
To show the video status, please press the MENU button.
User’s ManualEN-21
Copying and Deleting Files
NOTE
Photo, video and audio files in internal memory or on memory cards can be
deleted or copied on the digital photo album.
Copying Files from Memory Cards to an Album
After a memory card is inserted, on the album screen, memory card icons
are shown by pressing the MENU button:
1. Select the memory card icon and press OK to display the files in the
memory card.
2. Press the MENU button and Select the Backup icon in the displayed
icons, and then press OK.
3. In the pop-up window, Select YES to confirm. A status bar will be
displayed. The process can be stopped by selecting Cancel.
4. When copying is completed, a report will be displayed. Press OK to
close the window. A new album named SD-00001 (if copied from an SD
card) or CF-00001 (if copied from a CF card) will be created and
displayed on the album screen.
When the album is switched on with the memory cards
inserted, icons will automatically appear on the screen
for quick reference.
Only supported formats can be copied to the album.
Please refer to the Supported Formats section for
details.
Folders under DCIM will be copied and displayed as one
album. A common DCIM folder includes photos taken
with digital cameras.
Files are sorted alphabetically by file names.
Copying Files from a PC to an Album
1. When connected to the PC, the photo album is recognized as a USB
device and listed as a removable drive. Two folders will be listed under
the drive folder: Photo and Music.
2. Copy photo folders into Photo. They will be displayed as albums.
Copy the desired music files into Music for background music.
EN-22User’s Manual
When connected, memory cards inserted in the photo album are detected
NOTE
automatically and the album can be used as a card reader.
All folders and sub-folders will be displayed as albums.
Musical files not stored in the Music folder cannot be
played on the device.
Music files are played randomly by the digital photo
album.
Deleting Files in an Album
1. Select the album/photo/video to delete. Press the MENU button to
display the Delete icon.
2. Press OK and a pop-up window will ask for confirmation. Select YES
and press OK to confirm the deletion.
Setup
In this section you can set theme style, screen brightness, language, date
time, auto shutdown timer, and check the status of the digital album. To
enter Setup, press the MENU button to display the icons on the top left
corner and select the Setup icon, then press OK.
Press the up/down/left/right button to browse setup options. Press OK to
enter the option. The menu on the right will be highlighted.
Theme Style
Press the up/down/left/right button to select the desired theme style and
press OK. The theme style will be changed.
User’s ManualEN-23
Screen Brightness
Press the up/down/left/right button to adjust the screen brightness. To
confirm the setting, press the OK button.
Language
Use this option to choose the menu language for the digital album. Press
the up/down/left/right button to select your preferred language and press
OK to confirm your selection. The new setting will be effective immediately.
EN-24User’s Manual
Date/Time
NOTE
Use this option to set the time and date of the photo album. Press the up/
down/left/right button to adjust the value (year, month, date, time zone, hour, minute and second). You can go to the next selection by pressing OK.
Auto Shutdown Timer
Depending on your lifestyle and schedule, the digital album can be set to
automatically turn on and off.
Local time must be set correctly before setting up this
feature (see Date/Time section).
Press the up/down/left/right button to select an auto shutdown time and
press OK to confirm it.
User’s ManualEN-25
Status
NOTE
Select Status to check the status of the digital album. Status information
includes Internal Disk Size, Free space size, Hardware/Firmware Version
and the battery status.
Firmware Upgrades
To upgrade the firmware of the digital album:
1. Visit www.computers.toshiba-europe.com to download the latest
firmware, and save the firmware in your memory card.
2. Insert the memory card and select YES in the pop-up window to confirm
the firmware upgrade.
3. After firmware upgrades are completed, please wait for 10 seconds and
the system will reboot. Now the firmware is successfully upgraded.
4. Unplug the memory card after successfully upgarding the firmware.
After firmware is upgraded, delete the firmware file in the
memory card. If the file is not deleted and the memory
card is inserted in the digital album, the digital album will
execute upgrade each time it is turned on.
1Ds Mark-II, 1Ds, 1D-II, 1D, 5D, 20D, 10D, 300D (Digital Rebel, Kiss
Digital), 400D, Digital Rebel XT, D30, Power Shot G1/G2/G3/G5/G6
Frame
Rate
AudioFormatRemark
MPEG-1352x28830MPEG-1MPG-
MPEG-2720x48030MPEG-1/AC3MPG/VOBMPEG-2 MP@ML
MPEG-4720x48030AAC/MPEG-1MP4/MOV/AVIMPEG-4 SP
Xvid720x48030AAC/MPEG-1AV Iv5
Audio
Decoder
MAD483842MP3
User’s ManualEN-27
Sampling
Rate
(up to, kHz)
Bit Rate
(up to,
kbps)
Channels
(up to)
FormatRemark
MPEG-1 L1/2/3,
MPEG-2 L1/2
Frequently Asked Questions
Q: Why does my computer not show my photo album as a USB device
when I connect it?
A: Make sure the USB cable is properly plugged in. The metallic portion
should not be seen when properly connected.
Q: Why does a battery signal appear on the screen?
A: This is an indication of a low battery, please charge the device.
Q: How do I manage music files on the digital photo album?
A: Music files can be managed by connecting the digital photo album to a
PC and managing files in the “Music” folder.
Q: How do I control the music played?
A: The order of music files played cannot be controlled.
Specifications
Power
Size
Weight
Power Input100-240 volts AC, 50-60 hertz
Power Output5V/2A
Dimensions
(without cover)
Dimensions
(with cover)
Weight
(without cover)
Weight
(with cover)
246.4 (L) x 163.4 (W) x 13.9 (H) mm
266 (L) x 184.6 (W) x 37.5 (H) mm
550g
1000g
EN-28User’s Manual
TOSHIBA Support
Need help?
For the latest driver updates, user manuals & FAQs please have a look at
the TOSHIBA options & services support page:
computers.toshiba.eu/options-support
Please see computers.toshiba.eu/options-warranty
for the TOSHIBA hotline numbers.
Copyright Statement
No part of this publication may be reproduced in any form by any means
without prior written permission. Other trademarks or brand names
mentioned herein are trademarks or registered trademarks of their
respective companies.
Disclaimer
Information in this document is subject to change without notice. The
manufacturer does not make any representations or warranties (implied or
otherwise) regarding the accuracy and completeness of this document and
shall in no event be liable for any loss of profit or any commercial damage,
including but not limited to special, incidental, consequential, or other
damage.
December 2008, Rev1.0
Trademarks
Microsoft, Windows XP and Windows Vista are either registered
trademarks or trademarks of Microsoft Corporation in the United States
and/or other countries.
Other brands and product names are trademarks or registered trademarks
of their respective companies.
User’s ManualEN-29
Regulatory Statements
CE Compliance
This product is CE marked in accordance with the
requirements of the applicable EU Directives. Responsible
for CE marking is Toshiba Europe GmbH, Hammfelddamm
8, 41460 Neuss, Germany. A copy of the official
Declaration of Conformity can be obtained from following
website: http://epps.toshiba-teg.com.
Working Environment
The Electromagnetic Compliance (EMC) of this product has been verified
typically for this product category for a so called Residential, Commercial &
Light Industry Environment. Any other working environment has not been
verified by Toshiba and the use of this product in these working
environments is maybe restricted or cannot be recommended. Possible
consequences of the use of this product in non verified working
environments can be: Disturbances of other products or of this product in
the nearby surrounding area with temporarily malfunction or data loss/
corruption as result. Example of non verified working environments and
related advices:
n Industrial environment (e. g. where 3-phase 380V mains is being used
mainly): Danger of disturbances of this product due to possible strong
electromagnetic fields especially near to big machinery or power units.
n Medical environment: The compliance to the Medical Product Directive
has not been verified by Toshiba, therefore this product cannot be used
as a medical product without further verification. The use in usual office
environments e.g. in hospitals should be no problem if there is no
restriction by the responsible administration.
n Automotive environment: Please search the owner instructions of the
related vehicle for advices regarding the use of this product (category).
n Aviation environment: Please follow the instructions of the flight
personnel regarding restrictions of use.
EN-30User’s Manual
Loading...
+ 324 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.