Toshiba D3453-40, D3454-40 User Manual
ON-LINE MANUAL
40D345*DB
LED Backlight LCD TV
During the life of your TV rmware updates will be made available to
ensure that your TV maintains optimum performance.
You can download the latest version of rmware from
www.toshiba-om.net/rmware.php
Some features listed in this document are limited due to local legislation
and may not be available in all countries.
English
Get started with Freeview
Freeview gives you over 50 TV channels to play with, not to mention 25 radio stations.
Start watching all your favourite TV content today, just connect your aerial and tune in.
Keep up-to-date
New channels are launched on Freeview from time to time along with other updates to the
service. So it pays to retune your digital TV periodically to make sure your Digital TV/Radio
channels are up to date. To retune your Toshiba Digital TV, please refer to the Re-tune
section for guidance.
Alternatively nd out more on the dedicated Freeview website:
www.freeview.co.uk/retune
Freeview service is subject to availability. Aerial upgrade may be required.
English - 2 -
Contents
Safety Precautions ................................................. 5
Air Circulation ..................................................... 5
Heat Damage...................................................... 5
Mains Supply ...................................................... 5
Warning .............................................................. 5
Do ....................................................................... 5
Do not ................................................................. 5
Installation and Important Information .................... 6
EXCLUSION CLAUSE........................................ 6
Important safety information ................................... 7
Fitting or Removing the pedestal stand .................. 8
The Remote Control (TV - DVD) ............................ 9
Inserting Batteries and Effective Range of the
Remote Control................................................... 9
Connecting External Equipment ........................... 10
Connecting an HDMI
Input.......................................................................11
To Connect an HDMI Device .............................11
To Connect a DVI Device...................................11
Connecting a Computer........................................ 12
To Connect a Computer .................................... 12
Connecting to a DVD Player via YPbPr ............ 12
Connecting a USB Memory .................................. 12
To Connect a USB Flash Drive ......................... 12
Connecting a home network ................................. 13
Power Save Mode ................................................ 14
Environmental Information ............................... 14
Controlling the TV ................................................. 15
Switching on ..................................................... 15
Using the Remote Control ................................ 15
Using the Controls on the TV ............................ 15
Initial Installation ................................................... 16
Auto Tuning .......................................................... 18
Auto Tuning....................................................... 18
Auto Channel Scan Menu Operation ................ 18
Manual Tuning, Analogue Fine Tuning ................. 19
Digital Aerial Manual Search............................. 19
Digital Cable Manual Search ............................ 19
Analogue Manual Search ................................. 19
Analogue Fine Tune.......................................... 19
General Operation ................................................ 20
Stereo and Bilingual Transmissions.................. 20
Displaying Subtitles .......................................... 20
Viewing Main Menu .......................................... 20
Controlling Volume and Muting Sound ............. 20
Selecting Programme Positions........................ 20
Standby Notications ........................................ 20
Channel List, Sorting Programmes, Programme
Locking ................................................................. 21
Viewing Channel List ........................................ 21
Moving a Channel ............................................. 21
Deleting a Channel ........................................... 21
Renaming a Channel ........................................ 21
Locking a Channel ............................................ 21
®
or DVI Device to the HDMI
English - 3 -
Viewing Info Banner, Electronic Programme
Guide .................................................................... 22
Viewing Info Banner .......................................... 22
Electronic Programme Guide............................ 22
Language Selection .............................................. 23
Language Settings ............................................ 23
Preferred ....................................................... 23
Current .......................................................... 23
Digital Settings - Parental Control, Menu Lock, Set
PIN........................................................................ 24
Viewing Parental Control Menu ........................ 24
Menu Lock ........................................................ 24
Child Lock ......................................................... 24
Set PIN ............................................................. 24
Conguring Picture Settings ................................. 25
Conguring Picture Settings ............................. 25
Operating Picture Settings Menu Items ............ 25
Mode ................................................................. 25
Contrast ............................................................ 25
Brightness ......................................................... 25
Sharpness......................................................... 25
Colour ............................................................... 25
Power Save Mode ............................................ 25
Backlight ........................................................... 25
Noise Reduction ............................................... 25
Advanced Settings ........................................ 25
Reset ................................................................ 26
Changing Picture Format...................................... 27
Conguring PC Picture Settings ........................... 28
PC Picture Settings (*) ...................................... 28
PC Picture controls ........................................... 28
PC Position ....................................................... 28
Autoposition ...................................................... 28
H Position ......................................................... 28
V Position.......................................................... 28
Dot Clock .......................................................... 28
Phase................................................................ 28
Conguring Sound Settings .................................. 29
Conguring Sound Settings .............................. 29
Operating Sound Settings Menu Items ............. 29
Volume .............................................................. 29
Equalizer (Only for speaker) ............................. 29
Balance (Only for speaker) ............................... 29
Headphone ....................................................... 29
Sound Mode ..................................................... 29
AVL ................................................................... 29
Headphone/Lineout .......................................... 29
Dynamic Bass ................................................... 29
Surround Sound................................................ 29
Digital Out ......................................................... 29
Settings Menu Operation, Conditional Access ..... 30
Conguring Your TV’s Settings ......................... 30
Viewing Settings Menu ..................................... 30
Using a Conditional Access Module ................. 30
Viewing Conditional Access Menu (*) ............... 30
English
Contents
Setting Timers....................................................... 31
English
Timers ............................................................... 31
Setting Sleep Timer .......................................... 31
Setting Programme Timers ............................... 31
Adding a Timer.................................................. 31
Editing a Timer .................................................. 31
Deleting a Timer................................................ 31
Setting Date/Time ................................................. 32
Conguring Date/Time Settings ........................ 32
Conguring Source Settings ............................. 32
Input Selection .................................................. 32
Other Controls ...................................................... 33
Conguring Other Settings - General ............... 33
Operation .......................................................... 33
Menu Timeout ................................................... 33
Scan Encrypted Channels ............................... 33
Blue Background .............................................. 33
Software Upgrade ............................................. 33
Application Version ........................................... 33
Hard of Hearing ................................................ 33
Audio Description.............................................. 34
Auto TV Off ....................................................... 34
Standby Search (optional) ............................... 34
Store Mode ....................................................... 34
Media Renderer ................................................ 34
Power Up Mode ................................................ 34
Virtual Remote .................................................. 34
CEC .................................................................. 34
CEC Auto Power On ......................................... 34
Network Settings, Portal, Internet Browser and
YouTube ............................................................... 35
Conguring Network Settings ........................... 35
First enter to Toshiba Portal .............................. 35
Using the Toshiba Portal ................................... 35
Using the Internet Browser ............................... 35
Using YouTube
Using Media Browser ........................................... 37
Manual Start ..................................................... 37
Auto Start .......................................................... 37
Playing MP3 Files ............................................. 38
Viewing JPEG Files .......................................... 38
Slideshow Feature ............................................ 39
Video Playback ................................................. 39
Media Browser Settings .................................... 40
Using MENU button in Media Browser Mode ... 40
To Close the Media Player ................................ 40
Analogue Only Text Services ................................ 41
Analogue Text Services .................................... 41
Using Text Button -TEXT .................................. 41
Acessing Sub-Pages ........................................ 41
Revealing Concealed Text ................................ 41
Holding a Page ................................................. 41
To display an initial page................................... 41
Appendix A: PC Input Typical Display Modes ....... 42
Appendix B: AV and HDMI Signal Compatibility
TM
............................................. 36
(Input Signal Types) .............................................. 43
Appendix C: PIN Information ................................ 44
Appendix D: Supported File Formats for USB
Mode..................................................................... 45
DVD Mode ............................................................ 46
Handling Discs .................................................. 46
Cleaning Discs .................................................. 46
DVD - Features ................................................ 46
DVD - Control buttons on the TV ...................... 46
How to watch a DVD......................................... 47
Notes on DVD Playback ................................... 47
DVD Mode Conguration .................................. 48
TV Type ......................................................... 48
Language Setup ........................................... 48
OSD LANG ................................................... 48
AUDIO .......................................................... 48
DISC MENU .................................................. 48
SUBTITLE ..................................................... 48
DEFAULT ...................................................... 48
DOWNMIX .................................................... 48
SURROUND ................................................. 48
STEREO ....................................................... 48
PARENTAL .................................................... 48
PASSWORD ................................................. 48
SPDIF OUTPUT ............................................ 48
The DVD picture quality is poor ........................ 49
Appendix E: DVD Mode Supported le formats ... 50
Appendix F: Compatible disc types ...................... 50
Re-tune Section .................................................... 52
Re-tuning: TOSHIBA Freeview Products .............. 52
Specications and Accessories ............................ 53
License Information .............................................. 54
Q & A Section ....................................................... 55
English - 4 -
Safety Precautions
This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment,
care must be taken to obtain the best results and for safety to be assured. Please read the points below for your own safety.
They are of a general nature, intended to help with all electronic consumer products.
English
Air Circulation
Leave more than 10cm around all edges when wall mounting
the television to allow adequate ventilation. This will prevent
overheating and possible damage to the television. Dusty
places should also be avoided.
Heat Damage
Damage may occur if the television is left in direct sunlight
or near a heater. Avoid places subject to extremely high
temperatures or humidity, or locations where the temperature
is likely to fall below 5°C (41°F).
Mains Supply
The set should be operated only from a 220-240 V AC 50
Hz outlet. DO ensure that the television is not standing on
the mains lead. DO NOT cut off the mains plug from this
equipment, this incorporates a special Radio Interference
Filter, the removal of which will impair its performance. In the
UK, the fuse tted in this plug is approved by ASTA or BSI
to BS1362. It should only be replaced by a correctly rated
and approved type. IF IN DOUBT PLEASE CONSULT A
COMPETENT ELECTRICIAN.
Warning
To prevent the spread of re, keep candles or other open
ames away from this product at all times.
Do not
DON’T remove any xed cover as this may expose dangerous
voltages.
DON’T obstruct the ventilation openings of the equipment
with items such as newspapers, tablecloths, curtains, etc.
Overheating will cause damage.
DON’T allow electrical equipment to be exposed to dripping
or splashing or objects lled with liquids.
DON’T place hot objects or naked ame sources, such as
lighted candles or nightlights on, or close to equipment. High
temperatures can melt plastic and lead to res.
DON’T use makeshift stands and use the stand manufacturers
supplied screws.
DON’T leave equipment switched on when it is unattended,
unless it is specically stated that it is designed for unattended
operation or has a standby mode. Switch off by withdrawing
the plug, make sure your family know how to do this.
Special arrangements may need to be made for people with
disabilities.
DON’T continue to operate the equipment if you are in any
doubt about it working normally, or it is damaged in any way
- switch off, withdraw the mains plug and consult your dealer.
WARNING - excessive sound pressure from earphones or
headphones can cause hearing loss.
ABOVE ALL - NEVER let anyone, especially children,
push or hit the screen, push anything into holes, slots
or any other openings in the case.
NEVER guess or take chances with electrical equipment
of any kind - it is better to be safe than sorry.
THE MAINS PLUG IS USED AS A DISCONNECTING
DEVICE AND THEREFORE SHOULD BE READILY
OPERABLE.
Do
DO read these operating instructions before you attempt to
use the equipment.
DO ensure that all electrical connections (including the mains
plug, extension leads and inter connections between pieces
of equipment) are properly made and in accordance with the
manufacturers’ instructions. Switch off and withdraw the mains
plug before making or changing connections.
DO consult your dealer if you are ever in doubt about the
installation, operation or safety of your equipment.
DO be careful with any glass panels or doors on equipment.
English - 5 -
Note: Interactive video games that involve shooting a “gun”
type of joystick at the on-screen target may not work with
this TV.
The illustrations and the OSD in this operation
manual are for explanation purposes and may vary
slightly from the actual operations.
Installation and Important Information
English
Locate the television away from direct sunlight and strong
lights. Soft, indirect lighting is recommended for comfortable
viewing. Use curtains or blinds to prevent direct sunlight falling
on the screen.
Place the TV on a stable, level surface that can support the
weight of the TV. In order to maintain stability and prevent it
falling over, its recommended to secure the TV to a wall using
a sturdy tie on the back of the stand.
The LCD display panels are manufactured using an extremely
high level of precision technology; however, sometimes some
parts of the screen may be missing picture elements or have
luminous spots. This is not a sign of a malfunction.
Make sure the television is located in a position where it cannot
be pushed or hit by objects, as pressure will break or
The digital reception function of this television is only effective in the countries listed in the “Country” section
during the rst time installation menu. Depending on country/area, some of this television’s functions may not
be available. Reception of future additional or modied services cannot be guaranteed with this television.
If stationary images generated by 4:3 broadcasts, text services, channel identication logos, computer displays,
video games, on screen menus, etc. are left on the television screen for any length of time, they could become
conspicuous. It is always advisable to reduce both the brightness and contrast settings.
Very long, continuous use of the 4:3 picture on a 16:9 screen may result in some retention of the image at
the 4:3 outlines. This is not a defect of the LCD TV and is not covered under the manufacturer’s warranty.
Regular use of other size modes will prevent permanent retention.
Toshiba shall under no circumstances be liable for loss and/or damage to the product caused by:
i) re;
ii) earthquake;
iii) accidental damage;
iv) intentional misuse of the product;
v) use of the product in improper conditions;
vi) loss and/or damage caused to the product whilst in the possession of a third party;
vii) any damage or loss caused as a result of the owner’s failure and/or neglect to follow the instructions set out in the
owner’s manual;
viii) any loss or damage caused directly as a result of misuse or malfunction of the product when used simultaneously with
associated equipment;
Furthermore, under no circumstances shall Toshiba be liable for any consequential loss and/or damage including but not
limited to the following, loss of prot, interruption of business, the loss of recorded data whether caused during normal
operation or misuse of the product.
Where to install
* Button and stand
style is dependent on
model.
damage the screen. Also, please ensure that small items are
not inserted into slots or openings in the case.
Avoid using chemicals (such as air refreshers,
cleaning agents, etc.) on or near the TV pedestal.
Studies indicate that plastics may weaken and crack
over time from the combination effects of chemical agents
and mechanical stress (such as weight of TV). Failure to
follow these instructions could result in serious injury and/or
permanent damage to TV and TV pedestal.
Cleaning the screen and cabinet…
Turn off the power, and clean the screen and cabinet with
a soft, dry cloth. We recommend that you do not use any
proprietary polishes or solvents on the screen or cabinet as
this may cause damage.
Please take note
EXCLUSION CLAUSE
English - 6 -
Important safety information
• Any function related to the digital television (with the DVB logo) is available only within the country or area
where such signals are transmitted. Verify with the salesperson if it is possible to receive a DVB - T/T2/C
signal in the area where you live.
• Even if the television conforms to the required DVB - T/T2/C specications, the compatibility with future
digital DVB - T/T2/C transmissions is not guaranteed.
• Some digital television functions may not be available in certain countries.
• The DVB - T/T2/C system present in this device, allows reception of both FTA (Free To Air) and Encrypted
channels.
• Note; Encrypted channels require a specic encryption system to view, which may not be available in certain
countries.
• DVB is a registered trademark of the DVB Project. The DVB logo indicates that the product is compliant
with European Digital Broadcasting.
IMPORTANT INFORMATION
TV Installation
• Do not stand the televisions on cloth or other materials placed between the television and supporting furniture.
• Educating children about the dangers of climbing on furniture to reach the television or its controls.
• Always hold the plug when disconnecting the unit from the socket outlet. Do not pull on ex. The ex can
become damaged and cause a short circuit.
• Use a soft, dry cloth to clean the unit.
• Set up unit so that no one will trip over the ex.
• If you intend to wall mount the unit, contact the shop where you purchased the unit for advice, and leave the
installation work to professionals. Improper installation can cause damage and/or injuries.
• To protect the unit during a thunder storm, unplug the AC power cord and disconnect the aerial, cable and
satellite decoder/systems etc.
Caution: Do not touch the aerial connector.
• The unit becomes warm when in operation. Do not place any covers or blankets on the unit in order to
prevent overheating.
• The ventilation holes should not be blocked. Do not set up near radiators. Do not place in direct sunshine.
• Moisture condensation occurs in the following situations:
- When you move the unit from a cold place to a warm place.
- When you use the unit in a room where the heater was just turned on.
- When you use the unit in an area where cold air from an air conditioner directly hits the unit.
- When you use the unit in a humid place.
• Never use the unit when moisture condensation could occur.
• Using the unit when moisture condensation exists may damage its own internal parts. Allow two or three
hours, the unit will warm up and moisture will be evaporated before switching on.
English
English - 7 -
Fitting or Removing the pedestal stand
Fitting or Removing the pedestal stand
English
(1) Carefully lay the front of the unit face down on a at, cushioned surface with the stand hanging over the edge.
(2) To t the stand use the screws supplied.
or
(3) Remove the screws xing the pedestal stand
(4) After the screws are removed, hold the pedestal stand in place, then remove the pedestal stand and the
plastic moulding from the TV.
Note: Extreme care should always be used when removing the pedestal stand to avoid damage to the LCD panel.
For 40D345*DB model
When using a Wall Bracket
Please use a wall bracket appropriate for the size and weight of the LCD TV and two people are required for
the installation.
(1) Unplug and remove any cables and/or other component connectors from the rear of the TV.
(2) Carefully lay the front of the unit face down on a at, cushioned surface such as a quilt or blanket.
(3) Follow the instructions provided with your wall bracket. Before proceeding, make sure the appropriate
bracket(s) are attached to the wall and the back of the TV as described in the instructions provided with the
wall bracket.
English - 8 -
The Remote Control (TV - DVD)
3.
Simple at-a-glance reference of the remote control. The supplied type is model dependant.
1. Standby
Standby
2. Numeric buttons
Numeric buttons
3. TV-AV / Channel list / Switches
among broadcast types
4. Mute
Mute
5. Volume Up / Down
Volume Up / Down
6. Menu on-off
Menu
7. Navigation buttons
(Up/Down/Left/Right)
Navigation buttons
8. Okay (Conrm) / Hold (in TXT
mode) / Channel List
OK
9. Return / Index page (in TXT
mode)
10. Media Browser
Angle
11. Quick Menu
12. My button 1(*)
Display time / DVD menu
13. Coloured buttons
Red button - Zoom
Green button - Repeat
Yellow button - Root
Blue button - Title
14. Mono/Stereo - Dual I-II / Current
Language
(in DVB channels)
Language selection
15. Rapid reverse
Rapid reverse
(*) MY BUTTON 1 & MY BUTTON 2
These buttons may have default functions depending on the model.
However you can set a special function to these buttons by pressing on
them for ve seconds when on a desired source or channel. A conrmation
message will be displayed on the screen. Now the selected MY BUTTON
is associated with the selected function.
Note that if you perform rst time installation, MY BUTTON 1&2 will return
to their default function.
16. No function
17. Pause
Pause
18. Play
Play
19. Subtitle on-off (in Media Browser
mode and in DVB channels)
Subtitle
20. Stop
Stop
21. Rapid advance
Rapid advance
22. Image size
Image size
23. My button 2(*)
Search Mode
24. Teletext / Mix (in TXT mode)
25. Electronic programme guide(in
DVB channels)
26. Exit
Exit
27. Internet portal
28. Info / Reveal (in TXT mode)
Time
29. Programme Down /
Page up -
Programme Up / Page down
30. Previous programme
31. AV / Source selection
Source selection
Note: The references in Bold
are for models with and in DVD
operation.
English
Inserting Batteries and Effective Range of the Remote Control
Remove the back cover to reveal the battery compartment and make sure
the batteries are inserted the right way round. Suitable battery types for this
1.
remote are AAA, IEC R03 1.5V.
2.
Do not combine a used, old battery with a new one or mix battery types.
Remove exhausted batteries immediately to prevent acid from leaking into
the battery compartment. Dispose of them in a designated disposal area.
Warning: Batteries must not be exposed to excessive heat such as sunshine,
re or the like.
The performance of the remote control will deteriorate beyond a distance
of ve metres or outside an angle of 30 degrees from the IR receiver. If the
operating range becomes reduced the batteries may need replacing.
English - 9 -
English
D IH M 1
SPDIF
Coax.OUT
D IH M 2
HDMI Input
Sockets (*)
RGB/PC
Input
SCART
Socket
DIGITAL AUDIO
Socket
Side View
COMMON INTERFACE
The Common Interface is
for a Conditional Access
Module (CAM).
YPbPr
Headphone
SIDE AV
SIDE AV
YPbPr
5Vdc
Max:500mA
5Vdc
Max:500mA
LAN Input
USB Inputs (*)
Aerial
Input
Connecting External Equipment
Before connecting any external equipment, remove the mains plug from the wall socket.
(*) Number of these inputs may change according to the model of your TV.
Aerial cable:................................................................
Connect the aerial to the ANT. socket on the rear of the TV.
SCART lead:..............................................................
If you use a decoder* or a media recorder, it is essential
that the scart cable is connected to the TV.
Before running rst time installation, any connected devices
need to be set to standby mode.
The DIGITAL AUDIO socket enables the connection of a
suitable surround sound system.
®
HDMI
(High-Denition Multimedia Interface) is for using
with a DVD decoder or other equipment with digital audio and
video output. It is designed for best performance with 1080i
and 1080p high-denition video signals but will also accept
and display VGA, 480i, 480p, 576i, 576p and 720p signals.
PC format signals will also be displayed.
Note: Although this TV is able to connect to HDMI equipment,
it is possible that some equipment may not operate correctly.
When connecting a device via the Side AV input, you must
use the supplied connection cable to enable connection.
When connecting a device via YPbPr input, you must use the
supplied connection cable to enable connection.
LAN Input is used to connect the TV to your home network.
English - 10 -
A wide variety of external equipment can be connected to the
TV; therefore, the relevant owner’s manuals for all additional
equipment must be referred to for exact instructions.
If the TV automatically switches over to monitor external
equipment, return to normal TV by pressing the desired
programme position button. To recall external equipment,
press “SOURCE -
” button repeatedly to switch between
sources.
Regardless of source’s property, audio output from the
DIGITAL AUDIO socket cannot be copied.
Connecting an HDMI® or DVI Device to the HDMI Input
HDMI Input
Socket
(Back)
Colours
English
The HDMI inputs on your TV receive digital audio and
uncompressed digital video from an HDMI source device
or uncompressed digital video from a DVI (Digital Visual
Interface) source device.
These inputs are designed to accept HDCP (High-Bandwidth
Digital-Content Protection) programme material in digital form
from EIA/CEA-861-D–compliant [1] consumer electronic
devices (such as a set-top box or DVD player with HDMI
or DVI output).
NOTE:
• Some early HDMI equipment may not work properly with
your latest HDMI TV.
• Supported Audio format: Linear PCM, sampling rate
32/44.1/48kHz.
To Connect an HDMI Device
Connect an HDMI cable (type A connector) to the HDMI
terminal. For proper operation, it is recommended that you
use an HDMI cable with the HDMI Logo ( ).
• If your HDMI connection is capable of 1080p and/or
your TV is capable of refresh rates greater than 50Hz, you
will need a Category 2 cable. Conventional HDMI/DVI cable
may not work properly with this mode.
• HDMI cable transfers both video and audio. Separate
analogue audio cables are not required (see illustration).
• To view the HDMI device video, press “SOURCE -
button to select the appropriate HDMI input.
CEC
CEC operation is available if a CEC device is present. This
feature is limited to Toshiba disc players that support CEC.
The CEC osd menu is accessed through the “QUICK” button
on the remote the osd CEC menu will only be displayed if a
CEC product is connected.
To Connect a DVI Device
Connect an HDMI-to-DVI cable (HDMI type A connector) to the
HDMI input socket and audio cables to the RED and WHITE
SIDE AV AUDIO inputs on the Audio/Video connection cable
supplied (see illustration).
• The maximum recommended HDMI-to-DVI cable length
is 6.6 ft (2m).
• An HDMI-to-DVI cable transfers video only. Separate
analogue audio cables are required.
SIDE AV Input
Side Audio/Video
Connection Cable
(supplied)
”
Match
HDMI Input
Sockets
Audio Transfer
Audio Cable
(not supplied)
D IH M 1
* Number of
these inputs
may change
D IH M 2
according to
the model of
your TV.
Video Transfer
HDMI to DVI Cable
(not supplied)
* Number of
D IH M 2
these inputs
may change
D IH M 1
according to
the model of
your TV.
NOTE:
To ensure that the HDMI or DVI device is reset properly, it is
recommended that you follow these procedures:
• When turning on your electronic components, turn on the
TV rst, and then the HDMI or DVI device.
• When turning off your electronic components, turn off the
HDMI device
HDMI or DVI device rst, and then the TV.
English - 11 -
Connecting a Computer
English
Connecting a DVD Player
To Connect a Computer
With either an RGB/PC or an HDMI connection, you can watch
your computer’s display on the TV and hear the sound from
the TV’s speakers.
When connecting a PC to the RGB/PC input on TV, use an
analogue RGB (15-pin) computer cable and use the SIDE
AV socket with a PC audio cable (not supplied) for audio
connection, using the supplied Side AV connection cable’s
RED and WHITE inputs (see illustration).
To use a PC, set the monitor output resolution on the PC
before connecting it to the TV. To display the optimum picture,
use the PC setting feature.
NOTE:
• Some PC models cannot be connected to this TV. An
adaptor is not needed for computers with a compatible mini
D-sub15-pin terminal.
• Depending on the DVD’s title and the specications of the
PC on which you are playing the DVD-Video, some scenes
may be skipped or you may not be able to pause during
multiangle scenes.
Connecting to a DVD Player via YPbPr
Some DVD players are connected through COMPONENT
SOCKETS (YPbPr). In this case, you must use the supplied
Component YPbPr video connection cable for enabling
connection. First, plug the single jack of the cable to the TV’s
YPbPr socket (side). Afterwards, insert your YPbPr cable’s
(not supplied) connectors into the plural part of the supplied
YPbPr video connection cable (see illustration below). Colours
of the connected jacks should match.
To enable audio connection, use the supplied Side AV
connection cable. First, plug single jack of the cable to the
Side AV Input of the TV. Afterwards, insert your DVD player’s
audio cable’s connectors into the plural part of the supplied
Side AV connection cable (see illustration below). Colours of
the connected jacks should match.
Connecting a USB Memory
To Connect a USB Flash Drive
• You can connect a USB Flash Drive to your TV by using
the USB input/inputs on the TV. This feature allows you to
display/play music, photo or video les stored in a USB stick.
• It is possible that certain types of USB devices (e.g. MP3
Players) may not be compatible with this TV.
• You may back up your les before making any connections
to the TV set in order to avoid any possible data loss.
Note that manufacturer will not be responsible for any le
damage or data loss.
• Do not pull out USB module while playing a le.
CAUTION: Quickly plugging and unplugging USB
devices may cause damage to the USB device.
English - 12 -
Connecting a home network
English
Connectivity feature allows the TV to connect to the
home network wired or wirelessly. You can use this
networking system to connect to the Toshiba Portal or
to access photo, video and audio les that are stored
on a media server connected to the network and play/
display them on the TV.
Wired connection
Connect the TV to the modem/router via a LAN
cable (not supplied). Select Network Type as Wired
Device in Network Settings menu and then highlight
Network. Press Left or Right buttons and set as
Enabled to connect.
LAN input
on the TV
LAN Cable
modem/router
access point
LAN Cable
Broadband
ISP connection
Wireless connection
To connect the TV to the home network wirelessly just
select Network Type as Wireless Device in Network
Settings menu and then highlight Network. Press
Left or Right buttons and set as Enabled to connect.
The TV will search for available networks. Select the
desired network and press OK. The TV has a built-in
WLAN system and has no need for additional devices
to connect to a wireless network.
TV (Built-In WLAN system)
wireless modem/router
access point
LAN Cable
Broadband
ISP connection
Performance depends on many factors, conditions
and variables, including distance from acces
point(AP), volume of network trafc, building materials
and construction, operating system used, mix of
wireless products used, interference and other
adverse conditions.
Please refer to Network Settings section to congure
a wired or a wireless connection, if more detailed
information is needed.
English - 13 -
Power Save Mode
English
Environmental Information
This television is designed to be environment friendly. You not only help to save the environment but also
you can save money by reducing electricity bills thanks to the energy efciency feauture of this TV. To reduce
energy consumption, you should take the following steps:
You can use Power Save Mode setting, located in the Picture Settings menu. If you set Power Save Mode as
Eco, the TV will switch to energy-saving mode and luminance level of TV set will be decreased to optimum
level. Note that some picture settings will be unavailable to be changed when the TV is in Power Save Mode.
If pressed Right button, “Screen will be off in 15 seconds.” message will be displayed on the screen. Select
Proceed and press OK to turn the screen off immediately. If you don’t press any button, the screen will be off
in 15 seconds. Press any button on the remote or on the TV to turn the screen on again. If you disable Power
Save Mode, picture mode will be automatically set to Dynamic.
It is highly recommended to activate Power Save Mode to reduce your annual power consumption. And also
it is recommended to disconnect the TV from the mains plug to save more energy when you are not going to
use it for a long period of time.
Repair Information
Please refer all servicing to qualied personnel. Only qualied personnel must repair the TV. Please contact
your local dealer, where you have purchased this TV for further information.
English - 14 -
Controlling the TV
A wide variety of external equipment can be connected via the sockets located on the side and back of the
TV. Whilst all the necessary adjustments and controls for the TV are made using the remote control, the
buttons on the Back of the TV may be used for some functions.
English
Switching on
If the standby LED is unlit, check that the mains plug is
connected to the power and press the button on the
back side of the television or
to switch the television on.
To put the television into Standby, press
remote control or button on the TV. To view the television,
press again. The picture may take a few seconds to appear.
Note: The active Standby LED colour will turn to red in a few
moments when the TV is switched into Standby.
button on the remote control
button on the
For energy saving:
Turning the TV off at its mains supply, or un-plugging it, will cut
energy use to nearly zero for all TV’s. This is recommended
when the TV is not being used for a long time, e.g. when
on holiday.
Reducing the brightness of the screen will reduce energy use.
Note: Putting the TV into standby mode, will reduce energy
consumption, but will still draw some power.
Using the Remote Control
Press the MENU button on the remote control to see the
menus.
The main menu appears as a group of icons each for a menu
option. Press the Left or Right button to select a topic.
In sub menu screen mode the menu appears as a list. Press
the Up or Down button to select a topic.
To use the options press the Up and Down buttons on the
remote control to move up and down through them and OK,
Left or Right buttons to select the required choice. Follow
the on screen instructions. The functions of each menu are
described in detail throughout the manual.
Using the Controls on the TV
Using the control buttons on the Back of the TV:
• To alter the volume press
• To alter the programme position press
on the Back of the TV.
• Press
and use
change value.
To select an external input, press
appropriate input source is selected.
Please always refer to the owner’s manual of the equipment
to be connected for full details.
buttons at the same to view main menu
buttons to navigate and to
or .
buttons
button until the
English - 15 -
Initial Installation
Before switching on the TV, put your decoder and media recorder to Standby if they are connected and
English
ensure the aerial is connected to your TV. To set up the TV, use the buttons on the remote control as
detailed on The Remote Control page.
IMPORTANT: Ensure that the aerial is connected and
a Common Interface module is not inserted before
switching on the TV for the rst time installation.
1. Connect the mains plug and switch the TV on
using the
press any numbered or button on the remote
control, then the language selection menu will
be displayed. This screen will appear the rst
time that the TV is switched on and each time
the TV is reset.
2. By pressing Up or Down button, highlight the
language you want to set and press OK button.
The following screen will be displayed next:
button. If the TV does not switch on,
Note: Depending on the Country selection you may be asked
to set and conrm a PIN at this point. The selected PIN cannot
be 0000. You have to enter it if you are asked to enter a PIN
for any menu operation later.
5. The following message will be displayed next on
the screen:
Select Store mode if the TV will be placed in a
store to exhibit. This option will congure your
TV’s settings for best display quality and the
supported features of the TV will be displayed on
the top of the screen as a info banner. If Store
mode is selected, a conrmation screen will be
displayed. Select YES to proceed. For home use
select Home Mode.
This option will be available in Other Settings
menu and can be turned off/on later.
6. Press OK button on the remote control to continue
and a message will be displayed asking wheter
you want to do network settings. Select Yes and
the Network Settings menu will be displayed.
Please refer to Connecting a Home Network and
Network Settings sections to congure a wired
or a wireless connection. After the settings are
completed press OK button to continue.
7. Afterwards, the following OSD will be displayed
on the screen:
3. By pressing Left or Right button, select the
country you want to set and press Down button
to highlight the Search Type option. Use Left or
Right to set the desired search type. Available
search types are Digital only, Analogue TV
only and Full.
4. When set, press Down button to highlight
Teletext Language. Use Left or Right button to
select desired language region. Highlight Scan
Encryted Channels and enable/disable this
option by using Left or Right buttons. Press OK
to continue.
English - 16 -
8. If you select Cable option, a conrmation screen
will be displayed. If you want to search for
available networks, select YES to proceed. The
following screen will be displayed:
Note: Although this cable feature can be selected, it is not
fully supported in the UK. If cable signals are input to this
TV from a Cable Network Provider some may be displayed.
Initial Installation - continued
English
You can select Network, Frequency, Network
ID and Search Step from this screen. For
highlighting lines you see, use Up or Down button.
You can set Search Step as 8000 kHz or 1000
kHz. If you select 1000 kHz, the TV will perform
search process in a detailed way. Searching
duration will thus increase accordingly. When
finished, press OK button to start automatic
search.
If you select NO, the following screen will be
displayed:
You can set Start - Stop Frequencies and Search
Step as desired. When nished, press OK button
to start the search.
9. If you select Aerial option from the Search Type
screen, the television will search for broadcasts.
10. The Auto tuning screen will appear and the
television will start to search for available stations.
The progress bar will move along the line. You
must allow the television to complete the search.
Note: You can press MENU button to cancel.
While the search continues a message will appear,
asking whether you want to sort channels according
to the LCN(*). Select Yes and press OK to conrm.
(*) LCN is the Logical Channel Number system that organizes
available broadcasts in accordance with a recognizable
channel sequence (if available).
After the available stations are stored, Edit Channel
List will be displayed on the screen.
Press OK button to quit channel list and watch TV.
Note: Do not turn off the TV while initializing first time
installation.
English - 17 -
Loading...