Page 1
1
2. Safety Instructions
1. Introduction
Welcome and thank you for choosing a TOSHIBA product.
For details about your TOSHIBA product, refer to the User’s Manual or online
documentation which contains further information.
1. Do not drop, puncture or disassemble the camcorder; otherwise the warranty will be voided.
2. Avoid all contact with water, and dry hands before using.
3. Do not expose the camcorder to high temperature or leave it in direct sunlight.
Doing so may damage the camcorder.
4. Use the camcorder with care. Avoid pressing hard on the camcorder body.
5. For your own safety, avoid using the camcorder when there is a storm or lightning.
6. Do not use batteries of different specifications. Doing so may lead to the potential for
serious damage.
7. Remove the battery during long periods between usages, as a deteriorated battery may
affect the functionality of the camcorder.
8. Remove the battery if it shows signs of leaking or distortion.
9. Use only the accessories supplied by the manufacturer.
10. Keep the camcorder out of the reach of infants.
11. Risk of explosion if battery is replaced by an incorrect type.
12. Dispose of used batteries according to the instructions
3. TOSHIBA support
Need help?
For the latest driver updates, user’s manuals & FAQs please have a look at the
TOSHIBA options & services support page:
www.mytoshiba.com.au
www.mytoshiba.co.nz
Toshiba Support Centre:
Australia : 13 30 70
New Zealand: 0800 445 439
Expert staff provides technical assistance during normal business hours, 5 days a week,
excluding public holidays.
Be sure to have the following information available before you call:
Product serial number and part number
Place of purchase
Applicable error messages or fault symptoms
Operating system (if applicable)
Installed third-party hardware and software (if applicable)
Page 2
2
Slide the safety latch to the unlocked position and open the battery cover.
Insert the battery according to the correct polarity marks (+ or -).
NOTE: Please remove the insulator on battery connection before use.
Close the battery cover firmly and slide the safety latch to the locked position.
Recommended memory capacity of an SD card (Optional) -- 1GB or above.
4. Getting Started
Load the rechargeable Li-ion battery /SD card (Optional)
Li-ion battery
Insert the SD card (Optional)
into the right position.
To remove an SD card, press
it down and take it out.
Charge your battery
You must use the supplied AC charger or the USB cable.
The camcorder must be turned OFF;
blinking light confirms charging,
and the light becomes constant after the charging is completed.
Then, the light will turn itself off automatically after 5 minutes. (In AC charging Mode)
Page 3
3
5. Tour of Your Camcorder
Flip to power on
Flip out the LCD panel or hold
[Power ]Button for one second.
If no operation is made in 3 minutes,
the Camcorder will turn itself off
automatically to conserve battery power.
Dual record
1
3
4
To start or stop recording2
Record & Play
1
7
2
4
5
6
2
2 4
3 4
Press Mode Button or touch
on the screen to switch to
Movie Record mode. (The Movie
Mode LED Indicator will light up.)
Press
When recording movies, press Mode
Button to capture the image.
Dual record icon appears
on the LCD monitor.
To capture picture
Press Mode Button or touch
on the screen to switch to
Movie Record mode. (The Movie
Mode LED Indicator will light up.)
Press
5
To zoom in or out
Press [T]/[W]
6
To review movies/pictures
Press
7
To operate more advanced options
Touch (on-screen icon) to
access the option menu.
For more detailed operational
instructions, please refer to User’s
Manual-Section 3 &4 on the supplied
CD.
Page 4
4
Tele/Wide Button
Front/Side
SD card Slot
Microphone
Flash
Speaker
Lens
Mini USB 2.0 Port
HDMI Port
TV Port
LCD Touch Panel
Power Button
NOTE:
Please remove the
lens protect film on
lens before use.
Pre-Record/YouTube Direct Button
In Record Mode, press to activate the Pre-Record function and the
movies will be recorded 3 seconds before the OK Button is pressed.
In Movie Playback Mode, press to select the current movies to
upload to YouTube.
When the camera is connected with the computer, press to launch
YouTube Direct application automatically.
Page 5
5
Rear/Bottom
Playback LED Indicator
Picture Mode LED Indicator
Movie Mode LED Indicator
[Playback] Button
ISwitch between Record
/Playback Mode.
For quick review, press it
after recording.
[Mode] Button
When recording movies,
press to capture the image.
Switch between Movie
Mode and Picture Mode.
Switch between Movie
Preview Screen and
Picture Preview Screen.
Rolling Wheel
Rotate to move between
the wheel menu options.
Rotatel to move to the
previous/next movies/
pictures.
[Right] Button
LCD Information ON/OFF.
[Left] Button
Flash Auto/ Red eye
Reduction/Digital Light/Flash Off
[Down] Button
During Playback:
Press to delete movies/pictures.
[OK] Button
In Movie Record Mode,
press to take movies.
To stop recording, press it
again. In Picture Record
Mode, press to take pictures.
Validate the setting.
In Picture Playback Mode,
press to start/stop the slideshow.
Self Timer LED
Tripod Socket Battery Cover Safety latch
Record Mode Menu
Resolution
Movie Resolution
FHD (1080i 60)
FHD(1080p 30)
HD (720p 60)
HD(720p 30)
VGA(4:3)
1920X1080i (60fps)
1920X1080p (30fps)
1280X720p (60fps)
1280X720p (30fps)
640 X 480
Page 6
6
Picture Resolution
High(16MP)
Std(10MP)
Low(3MP)
White Balance
Auto
Daylight
Fluorescent
Tungsten
Scene
Auto
Skin
Night
Backlight
B/W
Classic
Negative
Effect
Movie Effect
Stabilization
Macro Mode
Motion Detect
Slow Motion
Time Lapse
Picture Effect
Self-Timer
Macro Mode
ISO
Setting
Sound
TV
On
Off
Auto
Macro
On
Off
On
Off
Off
1 Sec.
3 Sec.
5 Sec.
On
Off
Auto
Macro
Auto
800
1600
3200
On
Off
NTSC (60Hz)
PAL (50Hz)
4608X3456 (16M pixels)
3664x2748 (10M pixels)
2048x1536 (3M pixels)
Automatic adjustment
Use under outsides light condition
Use under fluorescent light condition
Use under tungsten light condition
Shoot without any special effect on the image
Shoot with an effect that makes skin tones more natural
Use Night mode for night scenes or low light conditions.
You can take shots when bright light is behind the subject.
The image is converted to black-and-white.
The image is converted to sepia look.
The image is converted as the negative of the normal
Enable motion stabilization, giving you smooth and stable video.
Stabilization doesn’t apply on FHD (1080i 60)
Disable motion stabilization
Start video recording while detecting movements of objects.
Disable Motion detection
Disable Slow Motion
Disable Time Lapse.
Record one frame per second.
Record one frame every 3 seconds.
Activate 10-second-delayed Self-timer
Disable Self-timer
Enable operation sound
Disable operation sound
TV output setting is NTSC standard.
TV output setting is PAL standard.
Disable The camera adjusts the ISO sensitivity of its images automatically.
The larger the number is, the higher the ISO sensitivity is set to.
Select a small number to shoot a smoother image.
Select a large number to shoot an image in a dark location or to shoot a subject
moving at high speed. (Note that the image may become noisy when the number is large.)
Record one frame every 5 seconds.
Record videos with slow motion effect. When the video is played,
the playback time will be longer than the actual recording time.
Focus Range:Wide:10cm( 3.9 inch )~Infinite , Tele:100cm( 39 inch )~Infinite.
Focus Range:Wide:1cm~Infinite( 0.39 inch ~ infinite) , Tele:60cm~Infinite( 23.4 inch ~ infinite)
Focus Range: Wide:1cm( 0.39 inch )~ Infinite, Tele:60cm( 23.4 inch )~ Infinite
Focus Range: Wide:1cm( 0.39 inch )~ Infinite, Tele:60cm( 23.4 inch )~ Infinite
Page 7
7
6. Plug & Share
Install the bundled application software, ArcSoft MediaImpression, to
view the movies correctly on PC.
Connect the computer and camcorder with the supplied mini USB2.0
cable as shown.
Movies and pictures can be found on your computer at
“My Computer\Removable Disk\DCIM\100MEDIA.”
Under this folder, you can view, delete, move, or copy the recorded
movies and pictures you want.
Uploading Video Files to YouTube
You can also share the recorded
movies on YouTube website via the
built-in YouTube Direct application
which offers you an easy way to
upload your video clips to YouTube
instantly.
(For more detailed operational
instructions, please refer to User’s
Manual-Section 9 on the supplied CD.)
Install bundled ArcSoft Software
1. Insert the supplied CD into your computer’s CD-ROM drive.
2. The autorun screen appears. Then, click on [Install Application Software].
Follow the on-screen instructions to complete the installation.
ArcSoft MediaImpression is a user-friendly application that helps you
managing your media, burning your video into a DVD, and uploading your
videos to YouTube easily.
ArcSoft MediaConverter is a powerful application that converts multiple
video formats into compatible format with your camcorder.
Language
Format
Time Setting
Default Setting
Yes
No
Yes
No
Format memory/ card
Do not format memory/ card
Restore default factory setting
Do not restore default factory setting
English, Czech, Danish, Dutch, Finnish, French, German, Greek, Italian, Norwegian, Polish,
Portuguese, Russian, Swedish, Spanish, Turkish.
Set up Date and Time
Page 8
8
About the battery pack
Use only batteries recommended by TOSHIBA as replacements. The battery
pack is lithium ion batteries, which can explode if not replaced, used, handled
or disposed of properly. Dispose of the battery as required by local ordinances
or regulations.
Charge the battery pack only in an ambient temperature between
5 and 35 degrees Celsius. Otherwise, the electrolyte solution might leak,
battery pack performance might deteriorate and the battery life might be
shortened.
Never install or remove the battery pack without first turning off the power and
disconnecting the AC adaptor.
Use only the product connected to an AC power source or optional TOSHIBA
Battery charger to charge the battery pack. Never attempt to charge the battery
pack with any other charger.
Loading...