Wireless LAN and your Health . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
User’s Manual5
Check the components
Check to make sure you have all of the following items:
Hardware
■ TOSHIBA AT100 Tablet
■ AC adaptor and power cord (2-pin plug or 3-pin plug)
■ Battery pack (installed in the tablet)
■ Sleeve case (provided with some models)
Documents
■ TOSHIBA AT100 Quick Start Guide
■ Instruction Manual for Safety and Comfort
If any of the items is missing or damaged, contact your dealer immediately.
Safety instructions
■ Always read the safety instructions carefully:
■ Do not disassemble, modify, tamper with or repair your product.
Disassembly, modification, tampering or repairing the product could
cause fire or electric shock, possibly resulting in serious injury. Please
contact an authorized Toshiba service provider for any repair service.
■ When handling the power cable/cord, follow these precautions:
■ Never tamper with the power cable/cord or plug.
■ Never splice, alter, bend or twist a power cable/cord.
■ Never pull on a power cable/cord to remove a plug from a socket.
■ Never place heavy objects on a power cable/cord.
■ Never run a power cable/cord through a pinch point such as a door
or window.
■ Never place a power cable/cord near a heat source.
■ Never use nails, staples or similar objects to fasten or attach cord in
place.
■ Never attempt to disassemble or repair an AC adaptor.
Doing any of the above may damage the cables, and/or result in a fire
or electric shock, possibly resulting in serious injury.
■ Always confirm that the power plug (and extension cable plug if used)
has been fully inserted into the socket, to ensure a secure electrical
connection. Failure to do so may result in a fire or electric shock,
possibly resulting in serious injury.
■ Be careful if you use a multiple connector. An overload on one socket
could cause a fire or electric shock, possibly resulting in serious injury.
TOSHIBA AT100
User’s Manual6
TOSHIBA AT100
■ If dust gets on the power plug connectors or connector base, turn the
power off and disconnect the power plug. Then clean the connector
and/or connector base with a dry cloth. Continuing to use the product
without cleaning the power plug may result in a fire or an electric shock,
possibly resulting in serious injury.
■ Always use the TOSHIBA AC adaptor that was provided with your
product, or use AC adaptors specified by TOSHIBA to avoid any risk of
fire or other damage to the product. Use of an incompatible AC adaptor
could cause fire or damage to the product possibly resulting in serious
injury. TOSHIBA assumes no liability for any damage caused by use of
an incompatible adaptor or charger.
■ Never plug the AC adaptor into a power source that does not
correspond to both the voltage and the frequency specified on the
regulatory label of the unit. Failure to do so could result in a fire or
electric shock, possibly resulting in serious injury.
■ Never attempt to connect or disconnect a power plug with wet hands.
Failure to follow this instruction could result in an electric shock,
possibly resulting in serious injury.
■ Never leave small parts such as covers, caps and screws within the
reach of infants or small children. Swallowing a small part may cause
choking and suffocation resulting in death or serious injury. If a part is
swallowed, immediately take appropriate emergency action and consult
a doctor.
■ Never allow any liquids to spill into any part of your product, and never
expose the product to rain, water, seawater or moisture. Exposure to
liquid or moisture can cause electric shock or fire, resulting in damage
or serious injury. If any of these eventualities should accidentally occur,
immediately:
1.Turn off the product.
2.Disconnect the AC adaptor from the power plug socket and product.
Do not turn on the power again, until you have taken the product to an
authorized service center. Failure to follow these instructions could
result in serious injury or permanent damage to the product.
■ Never place your product or AC adaptor on a wooden surface, furniture,
or any other surface that could be marred by exposure to heat since the
product base and AC adaptor's surface increase in temperature during
normal use.
■ Always place your product or AC adaptor on a flat and hard surface that
is resistant to heat damage.
■ Never place your product where it will be exposed to excess heat, such
as in direct sunlight, an unventilated vehicle or near a heater. This may
result in a system failure, malfunction, loss of data or damage to the
product.
■ Never place your product in a location where it will be exposed to
extremely low temperatures. This may result in a system failure,
malfunction or loss of data.
User’s Manual7
TOSHIBA AT100
■ Never subject your product to sudden temperature variations. This may
result in condensation, causing a system failure, malfunction or loss of
data.
■ Never operate your product on AC power during a thunderstorm. If you
see lightning or hear thunder, immediately turn off the product. An
electric surge caused by the storm, may result in a system failure, loss
of data or hardware damage.
■ Always use the battery pack supplied as an accessory or an equivalent
battery pack specified in the User’s Manual. Other battery packs have
different voltage and terminal polarities. Use of non-conforming battery
packs could generate smoke or cause fire or rupture, possibly resulting
in serious injury.
User’s Manual8
Getting Started & Grand Tour
This chapter provides an equipment checklist, grand tour of your tablet and
basic information to start using your tablet.
Some of the features described in this manual may not function properly if
you use an operating system that was not pre-installed by TOSHIBA.
Getting Started
■ All users should be sure to read the section Initial Setup.
This section provides basic information to start using your tablet. It covers
the following topics:
■ Connecting the AC adaptor
■ Turning on the power
■ Initial Setup
■ Turning off the power
■ Use a virus-check program and make sure it is updated regularly.
■ Never format storage media without checking its content - formatting
destroys all stored data.
■ It is a good idea to periodically back up main storage device to external
media. General storage media is not durable or stable over long
periods of time and under certain conditions may result in data loss.
Connecting the AC adaptor
The AC adaptor can automatically adjust to any voltage ranging from 100 to
240 volt and to a frequency of either 50 or 60 hertz, enabling you to use this
product in almost all country/region. The adaptor converts AC power to DC
power and reduces the voltage supplied to this tablet.
User’s Manual9
Getting Started & Grand Tour
(Sample Illustration) The AC adaptor (2-pin plug)
(Sample Illustration) The AC adaptor (3-pin plug)
■ Depending on the model, either a 2-pin or 3-pin adaptor/power lead will
be bundled with the tablet.
■ Do not use a 3-pin to 2-pin conversion plug.
■ The supplied power cord conforms to safety rules and regulations in
the region the tablet is bought and should not be used outside of this
region. In order to use the adaptor/tablet in other regions, you should
buy a power cord that conforms to the safety rules and regulations in
that particular region.
Attach the AC adaptor when you need to charge the battery or you want to
operate from AC power. It is also the fastest way to get started, because
the battery pack will need to be charged before you can operate from
battery power.
User’s Manual10
Getting Started & Grand Tour
■ Always use the TOSHIBA AC adaptor that was included with your
tablet, or use AC adaptors specified by TOSHIBA to avoid any risk of
fire or other damage to the tablet. Use of an incompatible AC adaptor
could cause fire or damage to the tablet possibly resulting in serious
injury. TOSHIBA assumes no liability for any damage caused by use of
an incompatible adaptor.
■ Never plug the AC adaptor into a power source that does not
correspond to both the voltage and the frequency specified on the
regulatory label of the unit. Failure to do so could result in a fire or
electric shock, possibly resulting in serious injury.
■ Always use or purchase power cables that comply with the legal
voltage and frequency specifications and requirements in the country of
use. Failure to do so could result in a fire or electric shock, possibly
resulting in serious injury.
■ Do not use a 3-pin to 2-pin conversion plug.
■ When you connect the AC adaptor to the tablet, always follow the steps
in the exact order as described in the User’s Manual. Connecting the
power cable to a live electrical outlet should be the last step otherwise
the adaptor DC output plug could hold an electrical charge and cause
an electrical shock or minor bodily injury when touched. As a general
safety precaution, avoid touching any metal parts.
■ Never place your tablet or AC adaptor on a wooden surface, furniture,
or any other surface that could be marred by exposure to heat since
the tablet base and AC adaptor's surface increase in temperature
during normal use.
■ Always place your tablet or AC adaptor on a flat and hard surface that
is resistant to heat damage.
1. Connect the power cord to the AC adaptor.
2. Connect the AC adaptor’s DC output plug to the DC IN 19V jack on the
tablet.
3. Plug the power cord into a live wall outlet - the Battery indicator on the
display panel of the tablet should glow.
Turning on the power
This section describes how to turn on the power - the Power and Battery
indicators will then indicate the status.
User’s Manual11
Getting Started & Grand Tour
2 PIN
3 PIN
Press the power button on the tablet to turn on the power.
(Sample Illustration) Turning on the tablet
Initial Setup
The Setup Screen will be the first screen displayed when you turn on the
power. Setup your tablet according to the following steps:
1. Choose the language as you want and then tap Start to continue.
2. Connect via Wi-Fi or 3G (if an option).
You may also skip this section and turn Wi-Fi on later in Settings
screen.
3. Choose Google
4. Set date and time, and tap Next to continue.
5. Register or log in with a Google account. You may also skip this section
by tapping Cancel.
™ location service and tap Next to continue.
Turning off the power
If you are not going to use your tablet for a long time, shut it down. You can
also turn the LCD off in order to extend the battery life.
Shut Down the Tablet
When you shut down the tablet, no data will be saved. The tablet will boot
to the main screen when the next time it is turned on.
User’s Manual12
Getting Started & Grand Tour
1. If you have entered data, either save it to flash memory or to other
storage media.
■ Press the Power button for 2 seconds and select OK to turn off the
tablet.
■ Never turn off the power while an application is running. Doing so could
cause loss of data.
■ Never turn off the power, disconnect an external storage device or
remove storage media during data read/write. Doing so can cause data
loss.
■ In any emergency case, you can also press the power button for about
six seconds to force power off.
2. Turn off any peripheral devices connected to the TOSHIBA AT100
tablet.
Do not turn the tablet or peripheral devices back on immediately - wait a
short period to avoid any potential damage.
Turning the LCD off/on
You can turn the LCD off (while the system is still on) in one of the following
ways:
■ Press the power button.
■ Set the screen timeout in the Settings.
To turn the LCD on:
■ Press the power button again.
Unlocking your screen
After turning on the LCD, the screen remains locked. You can unlock the
screen in the following ways:
1. Tap and hold the unlock icon ().
2. Slide the icon towards the appearing circle.
If you have set up a screen lock through one of the three ways as pattern,
PIN or password, the method of unlocking the screen will be different. See
Location & security section for other ways to protect your tablet and
privacy.
User’s Manual13
Grand Tour
Please handle your product carefully to avoid scratching or damaging the
surface.
The following figure shows the grand tour of your tablet.
Getting Started & Grand Tour
321
6
7
4
21
20
8
9
5
10
11
12
13
19 18
17151416
1. Web Camera LED12. Orientation lock switch
2. Microphone13. Memory media slot
3. Web Camera (front)14. Web Camera (back)
4. Wireless LAN, 3G* and Bluetooth
15. Mini USB port
antennas (not shown)
5. Battery cover lock16. HDMI port
6. Power indicator17. Universal Serial Bus (USB) 2.0 port
7. Battery indicator18. Headphone/Microphone combo jack
8. Wi-Fi/3G indicator19. DC IN 19V jack
9. Display screen20. Docking interface
10. Power button21. Speakers
11. Volume down/up buttons
*Provided with some models.
(Sample Illustration) Grand tour of the tablet
User’s Manual14
Getting Started & Grand Tour
Web Camera LEDThe Web Camera LED will glow blue when the
Web Camera is in operation.
MicrophoneA built-in microphone allows you to import and
record sounds for your application.
Web CameraYour tablet is equipped with a front Web Camera
and a back Web Camera used for recording
video or taking photographs with your tablet.
Wireless LAN
antennas
Some models are equipped with Wireless LAN
antennas.
Battery cover lockSlide this lock to the unlock () position in
order to remove the battery cover.
Power indicatorThe Power indicator LED normally glows white
when the tablet is turned on and the AC adaptor
is connected.
Battery indicatorThe Battery indicator shows the status of the
battery's charge - white indicates the battery is
fully charged while the power is being correctly
supplied from the AC power adaptor. For details,
please refer to Power conditions section.
Wi-Fi/3G indicatorThis indicator glows amber when the
communication function is used.
Display screenDisplay screen brightness can be adjusted in the
Screen settings.
3G antennasSome models are equipped with the 3G
antennas.
Bluetooth antennaSome models are equipped with a Bluetooth
antenna.
Power buttonPress this button to turn the tablet's power on
and off.
Volume down/up
buttons
Press these buttons to increase or decrease the
volume.
User’s Manual15
Getting Started & Grand Tour
Orientation lock switch
Switch to lock/unlock automatic rotation of the
screen orientation.
Memory media slotThis slot lets you insert an SD™/SDHC™/SDXC™
memory card, a miniSD™/microSD™ Card and a
MultiMediaCard.
Please refer to the Memory media slot section in
"Hardware & Options Operation" chapter for
details.
Keep foreign metal objects, such as screws, staples and paper clips, out of
the memory media slot. Foreign metal objects can create a short circuit,
which can cause damage and fire, possibly resulting in serious injury.
Mini USB portMini USB port allows you to connect this tablet to
your computer, which can be used to transfer
files.
Please refer to the Mini USB port section in
"Hardware & Options Operation" chapter for
details.
HDMI portHDMI port can connect with Type A connector
HDMI cable.
You can send video and audio signals via HDMI
cable. In addition to this, you can send and
receive control signals via it.
Please refer to the HDMI device section in
"Hardware & Options Operation" chapter for
details.
Universal Serial Bus
(USB 2.0) port
One Universal Serial Bus port, which complies to
the USB 2.0 standard, is provided.
Please refer to the USB device section in
"Hardware & Options Operation" chapter for
details.
Keep foreign metal objects, such as screws, staples and paper clips, out of
the USB port. Foreign metal objects can create a short circuit, which can
cause damage and fire, possibly resulting in serious injury.
Please note that it is not possible to confirm the operation of all functions of
all USB devices that are available. In view of this it may be noted that some
functions associated with a specific device might not operate properly.
User’s Manual16
Getting Started & Grand Tour
Headphone/
Microphone combo
jack
A 3.5 mm mini headphone/microphone combo
jack enables connection of a monaural
microphone or a stereo headphone.
Both the internal and external microphones will be disabled if you use a
headset other than a 4-pin headset headphone.
DC IN 19V jackThe AC adaptor connects to this jack in order to
power the tablet and charge its internal batteries.
Please note that you should only use the model
of AC adaptor supplied with the tablet at the time
of purchase - using the wrong AC adaptor can
cause damage to the tablet.
Docking interfaceThe interface enables the connection of an
optional dock described in Hardware & Options
Operation chapter.
SpeakersThe speakers emit sound generated by your
software as well as audio alarms, such as low
battery condition, generated by the system.
User’s Manual17
Power conditions
The tablet's operating capability and battery charge status are affected by
different power conditions, including whether an AC adaptor is connected,
whether a battery pack is installed and what the charge level is for that
battery.
The LED in the table below refers to the Battery indicator.
Getting Started & Grand Tour
AC
adaptor
not
connected
AC
adaptor
connected
Remaining
battery capacity is
above low battery
trigger point
Remaining
battery capacity is
below low battery
trigger point
No battery
installed
Battery fully
charged
Battery partially
charged
No battery
installed
Power on
• LED: off
• LED: blink
amber
• LED: off
• LED: white • LED: white
• LED: amber • LED: amber
• LED: off • LED: off
Power off
(no operation)
• LED: off
User’s Manual18
Basic Operations & Home screen
This chapter describes the basic operations of your tablet and the Home
screen.
Using the Touch Screen
You can use your finger to manipulate icons, buttons, menu items, the
onscreen keyboard, and other items on the touch screen.
■ Tap
Simply tap your finger on the touch screen to act on items on the
screen, such as application and settings icons, to type letters and
symbols using the onscreen keyboard, or to tap onscreen buttons.
■ Tap & hold
Tap & hold an item on the screen by tapping it and not lifting your finger
until an action occurs. For example, to customize the Home screen, you
tap an empty area on the Home screen until the screen settings utility
launches.
■ Drag
Tap & hold an item for a moment and then, without lifting your finger,
move your finger on the screen until you reach the target position. You
can drag items on the Home screen to reposition them.
■ Swipe or slide
To swipe or slide, you quickly move your finger across the surface of the
screen, without pausing when you first touch it (so you don’t drag an
item instead). For example, you slide the screen up or down to scroll a
list.
■ Double tap
Tap quickly twice on a webpage, map or other screen to zoom.
■ Pinch
In some apps (such as Browser and Gallery), you can zoom in/out by
placing two fingers on the screen at once and pinching them together or
spreading them apart.
User’s Manual19
Basic Operations & Home screen
5
12
3
4
678
Getting to know the
The HOME screen is your starting point for using all the installed
applications on your tablet. You can customize the HOME screen to display
the widgets, application shortcuts, wallpapers and other shortcuts you
prefer.
1. Apps menu5. Back
2. Customize6. Home
3. Widgets7. Recent apps
4. Application shortcuts8. System bar
HOME
screen
(Sample Illustration) Home screen
ItemDescription
CustomizeAdd widgets, apps, wallpapers, and more to your
WidgetsWidgets show you the latest updates of
Application shortcutsTap these icons on Home screen to open
BackReturn to the previous screen.
HomeReturn to the home screen.
Recent appsSee recent applications.
User’s Manual20
Home screen.
applications. You can tap the widgets to open
these applications.
applications.
ItemDescription
System barShow app notifications, tablet status and quick
settings.
Apps menuSee all your tablet’s apps.
■ Slide to see more Home screen panels.
■ Use panels to organize your widgets and shortcuts. See Customizing
the Home screen section for the details.
■ To return to the center panel, tap Home button.
Apps menu
Tap the icon at the upper right corner of Home screen to open Apps
menu.
You can find all your apps in this place.
To manage your apps, tap Settings → Applications → Manage
applications.
Opening and switching applications
The Apps menu, which you can open from the Home screen, holds icons
for all the applications on your tablet.
■ Ta p My apps tab on the top of Apps menu screen to view applications
that you downloaded and installed.
Basic Operations & Home screen
Opening an application
You may open any application by:
■ Tapping an application icon on the Home screen
■ Tapping an application icon from the Apps menu.
Switch to a recently used application
You may switch to recently used application by:
■ Tapping Recent apps icon (), and select the application that you
want to switch.
Monitoring your tablet’s status
The status bar appears on the bottom of every screen. It displays time and
icons indicating that you have received notifications and icons indicating
the tablet’s status, along with the current time.
User’s Manual21
Status icons
The icons on the right of the status bar indicate the status of your tablet.
Notification icons
The icons on the left of the status bar indicate different types of
notifications. In addition to system notification icons, applications you
installed on your tablet may use their own notification icons.
Quick Settings
You can use Quick Settings to change settings, such as Airplane mode,
Wi-Fi, Lock screen orientation, Brightness, Notifications. Double tap
the status bar to open Quick Settings screen, and tap the area outside of
the Quick Settings screen to close it.
■ Airplane mode
Turn on airplane mode to disable all wireless radios.
■ Wi-Fi
Tap to open Wi-Fi Setting screen.
■ Lock screen orientation
Turn on this option to lock screen orientation as you turn your tablet
sideways.
■ Brightness
Set the brightness of display. You can also tap Auto to adjust
brightness automatically.
■ Notifications
Turn on this option to show notification on system bar.
■ Settings
Tap this option to open Settings screen.
Basic Operations & Home screen
Managing Notifications
Notification icons report the arrival of new messages, calendar events, and
alarms, as well as ongoing events.
When you receive a notification, its icon appears in the status bar, along
with a summary that appears only briefly.
You can open the Notifications panel to view a list of all your notifications.
Depending on your settings and the model of your tablet, you may also
hear a notification sound.
Adjusting sound volume and other general notifications settings is
described in the Sound settings in "Settings" chapter.
Applications that produce notifications, such as Email, have their own
settings, which you can use to configure whether and how they send
notifications. See the sections on those applications for details.
User’s Manual22
Opening the Notifications panel
Tap the status bar to open the notifications panel. The notifications panel
displays a list of your current notifications. Notifications about ongoing
activities are listed first, followed by notifications about events, such as a
new mail notifications.
Responding to a notification
To respond to a notification, follow the below steps:
1. Open the notifications panel.
Your current notifications are listed in the panel, each with a brief
description.
2. Tap a notification to respond to it.
The notifications panel closes. What happens next depends on the
notification.
Closing the Notifications panel
Tap the area out of the notifications panel to close the notifications panel.
Locking your screen
You can lock your screen so that only you can unlock it to access your data,
run applications and so on. See Location & security section for other ways
to protect your tablet and privacy.
Basic Operations & Home screen
Locking your screen with a Pattern lock
For example, you can use a Pattern lock to lock your screen with following
steps.
1. Open the Location & security settings by tapping the Apps →Settings→Location & security.
2. Tap Configure lock screen →Pattern.
The first time you open it, a short tutorial about creating an unlock pattern
will appear. Then you’re prompted to draw and redraw your own pattern.
Follow the onscreen instructions to finish the creation.
The next time you turn on your tablet or wake up the screen, you will be
prompted to draw your unlock pattern to unlock the screen.
Customizing the Home screen
You can add application icons, shortcuts, widgets and other items to any
part of the Home screen. You can also change the wallpaper.
User’s Manual23
Basic Operations & Home screen
Adding an item to the Home screen
To add an item to the Home screen, follow the steps listed below:
1. Tap the icon at the upper right corner of the home screen.
2. Tap a tab of Widgets, App shortcuts, Wallpapers or More.
3. Drag the Widgets, shortcuts, or other items to the Home screen panel
you want.
■ You can also tap Widgets, shortcuts to add them to current Home
screen panel.
■ The amount of Widgets you can add depends on the size of Widgets.
■ Widgets
Add any of a variety of miniature applications (widgets) to your Home
screen, including an analog clock, a music player, and a picture frame. You
can also download widgets from other websites.
■ App shortcuts
Add shortcuts to applications you have installed.
■ Wallpapers
Add a wallpaper you like or change the wallpaper for your Home screen
from the Gallery, Live Wallpapers or Wallpapers.
■ More
Add shortcuts to bookmarks, contacts, playlists and so on.
You can also add items to the Home screen by following ways:
■ Tap and hold an empty area of the Home screen.
■ Tap and hold an app shortcut on Apps menu, and drag it to the Home
screen panel you want.
Moving an item on the Home screen
To move an item on the Home screen, follow the steps below:
1. Tap and hold the item you want to move until its icon is magnified. Don’t
lift your finger from the screen.
2. Drag the item to a new location on the screen.
It will pause at the left or right edge of the screen to drag the item onto
extended Home screen.
3. When the item is at where you want it, lift your finger.
Removing an item from the Home screen
To remove an item from the Home screen, follow the steps below:
1. Tap and hold the item you want to remove until its icon is magnified.
A Trash bin icon appears on the top right corner.
2. Drag the item to the Trash bin icon.
3. When the icon glows red, lift your finger.
User’s Manual24
Changing the Screen Orientation
You can change the screen orientation to Portrait mode by rotating the
tablet sideways. The screen orientation automatically changes according to
the rotation angle detected.
You can also lock the auto rotation and use the tablet always in Portrait or
Landscape mode. These settings can be performed in the Screen settings.
Please refer to Screen section for details.
In the Portrait mode, some drivers/utilities may not perform install and
uninstall operation. If it occurs, switch to the Landscape mode to proceed.
Managing Tasks and Applications
You can manage some of the running applications, please follow the steps
below:
1. Tap Apps→Settings → Applications → Manage applications.
2. Tap an item you want to manage from Downloaded/Running/All tab.
Please refer to Applications in Settings section for details.
You can close an item by tapping Force stop, or remove an item by
tapping Uninstall.
In order to improve the performance of your tablet, close some of the
running applications.
Basic Operations & Home screen
Factory Reset
The tablet provides you with the function to reset it. Before executing this
function, you need to backup the system settings, application settings, user
installed applications and data in the internal storage.
To perform the factory data reset, please follow the steps below:
1. Tap Apps→Settings→Privacy→Factory data reset→Reset tablet → Erase everything.
2. The factory data reset will be done.
■ Please note that the following data will be erased:
■ System settings and application settings
■ User installed applications
■ Internal storage files, such as music or photos
■ Data in the removable media will not be erased.
User’s Manual25
Connecting to networks
Your tablet can connect to a variety of networks and devices, mobile
networks for voice and data transmission, Wi-Fi data networks and
Bluetooth devices, such as headsets. This chapter will describe how to
connect to different networks.
Connecting to mobile networks
This section only applies to models with 3G modules.
When you assemble your tablet with a SIM card from your wireless service
provider, your tablet is configured to use your provider’s mobile networks
for transmitting data.
Your tablet is configured to work with many mobile carriers’ networks. If
your tablet does not connect to a network when you insert a SIM card and
turn it on, contact your carrier to obtain the details of its access point name.
Disabling data when roaming
1. Open the Settings screen.
2. Tap Wireless & networks→Mobile networks, and uncheck Data roaming.
With Data roaming unchecked, you can still transmit data with a Wi-Fi
connection.
Editing or creating a new access point
If you and your wireless service provider determine that you need to
change the settings of your current access point name (APN) or to create a
new one, you must obtain the APN and detailed settings from your provider.
1. Open the Settings screen.
2. Tap Wireless & networks→Mobile networks→Access Point Names.
3. Tap an existing APN to edit it, or tap New APN to create a new one.
Enter the APN settings that you obtained from your wireless service
provider by tapping each setting that you need to edit.
4. When you finished, tap Save.
If you have created a new APN, tap it in the APNs screen to start using
it.
User’s Manual26
Loading...
+ 59 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.