SERVICE MODE ...................................................................................................................................................... 6
SETTING & ADJUSTING DATA .............................................................................................................................. 18
LOCATION OF CONTROLS ................................................................................................................................... 19
SPECIFICATIONS .............................................................................................................................................. END
APPENDIX:
CIRCUIT DIAGRAM
-
2
-
CHAPTER 1 GENERAL ADJUSTMENTS
SAFETY INSTRUCTIONS
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRECAU-
TION” AND “PRODUCT SAFETY NOTICE” INSTRUCTIONS BELOW.
X-RAY RADIATION PRECAUTION
1. Excessive high voltage can produce potentially hazardous
X-RAY RADIATION. To avoid such hazards, the high voltage must not be above the specified limit. The nominal value
of the high voltage of this receiver is (A) kV at zero beam
current (minimum brightness) under a (C) V AC power source.
The high voltage must not, under any circumstances, exceed (B) kV.
Refer to table-1 for high voltage (A), (B) & AC voltage (C).
(See SETTING & ADJUSTING DATA on page 18)
Each time a receiver requires servicing, the high voltage
should be checked following the HIGH VOLTAGE CHECK
procedure in this manual. It is recommended that the reading of the high voltage be recorded as a part of the service
record. It is important to use an accurate and reliable high
voltage meter.
SAFETY PRECAUTION
WARNING : Service should not be attempted by anyone unfamiliar with the necessary precautions on this receiver. The following
are the necessary precautions to be observed before servicing this chassis.
1. An isolation transformer should be connected in the power line between the receiver and the AC line before any service is
performed on the receiver.
2. Always discharge the picture tube anode to the CRT conductive coating before handling the picture tube. The picture tube
is highly evacuated and if broken, glass fragments will be violently expelled. Use shatter proof goggles and keep picture tube
away from the unprotected body while handling.
3. When replacing a chassis in the cabinet, always be certain that all the protective devices are put back in place, such as; nonmetallic control knobs, insulating covers, shields, isolation resistor-capacitor network etc.
2. The only source of X-RAY RADIATION in this TV receiver
is the picture tube. For continued X-RAY RADIATION protection, the replacement tube must be exactly the same
type tube as specified in the parts list.
3. Some part in this receiver have special safety-related characteristics for X-RAY RADIATION protection. For continued safety, parts replacement should be undertaken only
after referring to the PRODUCT SAFETY NOTICE below.
GENERAL ADJUSTMENTS
PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These characteristics are
often passed unnoticed by a visual inspection and the protection afforded by them cannot necessarily be obtained by using
replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in this manual and its supplements; electrical components having such features are identified by
the international hazard symbols on the schematic diagram and the parts list.
Before replacing any of these components, read the parts list in this manual carefully. The use of substitute replacement
parts which do not have the same safety characteristics as specified in the parts list may create shock, fire, X-ray
radiation or other hazards.
-
3
-
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRECAU-
TION” AND “PRODUCT SAFETY NOTICE” ON PAGE 3 OF SERVICE MANUAL.
SET-UP ADJUSTMENT
■ The following adjustments should be made when a complete realignment is required or a new picture tube is installed.
Perform the adjustments in order as follows :
1. Color Purity
2. Convergence
3. White Balance
Note: The PURITY/CONVERGENCE MAGNET assembly and rubber wedges need mechanical positioning.
Refer to figure 1.
COLOR PURITY ADUSTMENT
(1) Let the screen face in the installing direction or toward the east (when it is to be moved), bring up the service mode
GENERAL ADJUSTMENTS
screen after demagnetizing (front, left, right, and top) with the degaussing coil, receive white signals by pressing the
[TV/VIDEO] button, and then the receiver should be operated for more than 40 minutes.
(2) Perform rough adjustment of the central convergence with the P/C magnet according to the adjustment item.
(3) Receive built-in green signals, loosen set screws on the deflection yoke, remove rubber wedges, and shift the deflec-
tion yoke to toward front.
(4) Move alternately the two 2-pole magnets of the P/C magnets so that the green raster can come to the center of the
screen.
Figure 1.
2-pole purity magnet
(27": Magnet is fixed with deflection yoke.)
Green Belt
6-pole convergence magnet
Main 4-pole convergence magnet
P/C magnet installing position A
MAG-1108 : 37 mm
A
Sub-4-pole convergence magnet
MAG-1113 : 39 mm
(5) Receive built-in red and blue signals, check that there is no inclination of the single color raster toward one side, and if
each color tilts to a great extent, make adjustment with the 2-pole magnet so that the 3 colors will come to the center
evenly.
(6) Receive the green raster, shift the deflection yoke from
a foremost position (hitting against the picture tube) to a
Shift deflection yoke
(7) Perform marking of each point
(6)
(8)
on the tape of picture tube
backward position horizontally, stop the deflection yoke
at a position where it begins to become a green raster,
and perform accurate marking on the picture tube.
(7) Shift the deflection yoke further backward, and perform
Picture tube
CRT-D board
accurate marking at a position where the green raster
begins to being luck.
(8) Fix the deflection yoke at a position 60% forward within
the range marked in items (6) and (7) above.
CONVERGENCE ADJUSTMENTS
100 60 0%
Fix the deflection yoke at a position 60% forward from a
point between (6) and (7)
P/C Mag
* Adjust the convergence magnet to get vest convergence in the the order to (1) ~ (5).
■ CENTER CONVERGENCE:
(1) Receive the white crosshatch or dot pattern from the service signal generator.
(2) Use the 2 pieces of main 4-pole magnets of P/C magnets, change the open angle, and align the red and blue vertical
lines on the screen center.
(3) Freeze the open angle of the main 4-pole magnets, turn them simultaneously, and align the horizontal lines.
(4) Take the same steps for items (2) and (3) above and align red/blue with green on the screen center using two 6-pole
magnets.
-
4
-
(5)Adjust the sub-4-pole magnets only in case there is any deviation of Xv bow-shaped convergence. (To be usually set at
the initial position)
Align both sides with the sub-4-pole magnets and minimize the deviation of blue and red with the main 4-pole magnets.
blue
blue
red
red
Main 4-pole magnet
■ CIRCUMFERENCE CONVERGENCE:
Perform correction in the following manner.
*
blue
green
red
A
B
blue
green
red
C
(Parts code:23 948 274) TC-S
D
E
F
S
N
Blue color or blue mark
Bonded surface
red/blue
red/blue
green
green
6-pole magnet
• Adjust coils and minimize deviation
(The 27” unit has coils underneath it)
(Insertion position of correction
piece)
D
E
F
*Insert the correction piece between the
picture tube and the deflection yoke.
A
B
C
Xv bow-shaped deviation of convergence
blue
red
Sub-4-pole magnet
A
blue
B
green
red
C
(Parts code:23 948 464)
N
S
Bonded surface
Transparent
GENERAL ADJUSTMENTS
D
E
F
Adjust (YHC) and minimize the deviation of YH.
green
Red
blue
green
blue
Red
blue
Red
Adjust (YV) and minimize the deviation of YV.
Red
green
blue
blue
green
Red
Red
blue
green
GH
green
blue
red
green
blue
red
green
Red
green blue
green
green
Red
blue
Red
Red
green
blue
blue
YV YHC
Perform correction by insert-
GH
ing the correction piece into
the clearance of terminal
board coils of the deflection
yoke.
Note:
Perform insertion by turning
the metal side to the terminal
board side of the deflection
yoke.
-
5
-
1. ENTERING TO SERVICE MODE
1) Press o button once on
Remote Control.
SERVICE MODE
2) Press o button again to
keep pressing.
3) While pressing the o button,
press MENU button on TV set.
or Sound Mute
GENERAL ADJUSTMENTS
2. DISPLAYING THE ADJUSTMENT MENU
1)Press MENU button on TV.
Service mode
S
3. KEY FUNCTION IN THE SERVICE MODE
The following key entry during display of adjustment menu provides special functions.
Screen adjustment mode ON/OFF:-/-- button (on Remote)
Test signal selection :a button (on Remote)
Selection of the adjustment items :Channel s/t (on TV or Remote)
Change of the data value :Volume ; +/– (on TV or Remote)
Adjustment menu mode ON/OFF :MENU button (on TV)
Initialization of the memory (QA02) :CALL + Channel button on TV (s)
Reset the count of operating protect
Color thickness correction
note: Displayed differently as shown below, de-
pending on the setting of the receiving color
system.
COLP (PAL)
COLC (NTSC)
COLS (SECAM)
CAUTION : Never try to perform initialization unless you have changed the memory IC.
-
6
-
4. SELECTING THE ADJUSTING ITEMS
1)Every pressing of CHANNEL s button in the service mode changes the adjustment items in the order of table-2.
(t button for reverse order)
Refer to table-2 for preset data of adjustment mode.
(See SETTING & ADJUSTING DATA on page 27)
5. ADJUSTING THE DATA
1) Pressing of VOLUME ; +/– button will change the value of data in the range from 00H to FFH. The variable range
depends on the adjusting item.
6. EXIT FROM SERVICE MODE
1) Pressing POWER button to turn off the TV once.
■ INITIALIZATION OF MEMORY DATA OF QA02
After replacing QA02, the following initialization is required.
1. Enter the service mode, then select any register item.
2. Press and hold the CALL button on the Remote, then press the CHANNEL s button on the TV. The initialization of QA02 has
been complated.
3. Check the picture carefully. If necessary, adjust any adjustment item above.
Perform “Auto tune” on the owner’s manual.
CAUTION: Never attempt to initialize the data unless QA02 has been replaced.
7. TEST SIGNAL SELECTION
1) Every pressing of a button on the Remote Control changes the built-in test patterns on screen as described below
in SERVICE MODE.
18)
GENERAL ADJUSTMENTS
Signal off
ALL White
SignalsPicture
• All White
-
7
-
8. SELF DIAGNOSTIC FUNCTION
1) Press “9” button on Remote Control during display of adjustment menu in the service mode.
The diagnosis will begin to check if interface among IC’s are executed properly.
2) During diagnosis, the following displays are shown.
1
2
3
4
5
GENERAL ADJUSTMENTS
6
1
Firmware:
JH9_000
34JH9UH
Version information of microprocessor
In case of file name : JH9 and Version : 1.00 indicates[JH9_100].
2
Time: Total hour of turn the TV on. (Unit : H)
Power : Operation number of protecting circuit ----"00" is normal.
3
When indication is other than "00", overcurrent apt to flow, and circuit parts may
possibly be damaged.
BusCont : --- "OK" is normal.
4
When type name of semiconductor indicates.
BLOCK
5
UV : TV reception mode
VIDEO 1 input mode (
V1 :
V2 : VIDEO 2 input mode (
V3 : VIDEO 3 input mode (
V4 : VIDEO 4 input mode (
V5 : VIDEO 5 input mode (
Model name (7 digit)
6
1)
2)
3)
C1)
C2)
-
8
-
1. ENTERING TO DESIGN MODE
1) Select the Service mode.
DESIGN MODE
2) While pressing CALL button on Remote
and press MENU button on TV.
3) The following displays
are shown on the screen
SD
(Design mode)
q
1
JH9_039
4567 89
rtyuio
we
23
Press
Press
JH9_039
Version information of
q
microprocessor
Main tuner information
w
Sub tuner information
e
Selectable picture information
r
Position information
t
Signal information
y
Screen size information
u
Sound system information
i
Scan mode information
o
GENERAL ADJUSTMENTS
When QA02 is initialized, item “OPT3" of DESIGN MODE is set to the data of the representative model of this chassis family.
Therefore, because ON-SCREEN specification remains in the state of the representative of model. This model is required to
reset the data of item “OPT3".
2. SELECTING THE ADJUSTING ITEMS
Every pressing of CHANNEL t button in the design mode changes the adjustment items in the order of table-3.
(s button for reverse order)
Refer to table-3 for data of design mode.
(See SETTING & ADJUSTING DATA on page 27)
18)
3. ADJUSTING THE DATA
Pressing of VOLUME s or t button will change the value of data.
-
9
-
ELECTRICAL ADJUSTMENTS
ITEMADJUSTMENT PROCEDURE
FOCUS VR ADJ
SUB-BRIGHTNESS
(BRTC)
Note: Constrict the picture height
GENERAL ADJUSTMENTS
until the vertical retrace line
appears adjusting the item
HIT (HEIGHT).
HORIZONTAL POSITION
ADJUSTMENT (HPOS)
VERTICAL POSITION
ADJUSTMENT (VPOS)
1. Enter the service mode, then select any register item.
2. Press the TV/VIDEO button on the Remote until the black cross-bar pattern appears on the screen.
3. Adjust the FOCUS control (on T461) for well defined scanning lines on the picture
screen.
1. Set CONTRAST to minimum, and
BRIGHTNESS to center by adjusting user
controls.
2. Set the TV in service mode to get Black
cross-bar of inside pattern.
3. Select BRTC (brightness correction), and
adjust the ; – /+ button to reduce the
value so that white portion of inside pattern slightly light.
4. Adjust ; – /+ button to increase the data
value of BRTC, and set it just before the
difference between the belt of vertical retrace and the border of black portion of
inside pattern is visible.
After that, return vertical height and contrast.
1. Set the TV in service mode, and get
black cross-bar signal with VIDEO
button on remote hand unit.
2. Select either HPOS (Horizontal picture phase) or VPOS (Vertical picture
phase) with CHANNEL s, t buttons,
and adjust horizontal or vertical picture position in the center of screen
with VOLUME ; – /+ buttons.
Belt of vertical retrace
VERTICAL AMPLITUDE
ADJUSTMENT (HIT)
1. Set the TV in service mode, and get
black cross-hatch signal with VIDEO
button on remote hand unit.
2. Select HIT (Vertical amplitude) with
CHANNEL s, t buttons, and adjust
vertical amplitude with VOLUME
; – /+ buttons so that vertical amplitude lacks a little.
3. Adjust vertical amplitude with VOLUME ; – /+ buttons so that the first
bar on cross-hatch signal touches
edge of screen.
The first
-
10
-
ITEMADJUSTMENT PROCEDURE
WIDTH
(WID)
E-W PARABOLA
(PARA)
WHITE BALANCE
ADJUSTMENT
CUTOFF ADJUSTMENT
•
(RCUT)
(GCUT)
(BCUT)
DRIVE ADJUSTMENT
•
(GDRV)
(BDRV)
1. Call up the adjustment mode display, then select the item WID.
2. Press the ; – /+ button to get the picture so the left and rightedges of raster
begins to lack.
3. Press the ; – /+ button to advance the data by 7 steps.
Note : Check the horizontal picture position is correct.
1. Call up the adjustment mode display, then select the item PARA.
2. Press the a button on Remote until the cross-hatch pattern appears on the screen.
3. Press the ; – /+ button to make vertical lines straight as shown below.
GENERAL ADJUSTMENTS
1. Set Contrast to 40, and brightness to +20 by picture control.
2. Receive the Black and White pattern.
3. Select RCUT, GCUT and BCUT with CHANNEL s, t buttons, to set individual
values to Initial reference data, and to set GDRV and BDRV to Initial reference
data with VOLUME ; – /+ buttons.
4. Press -/- - button on the remote control and rotate Screen VR to get one slight
horizontal line on screen.
Note: Every pressing of -/- - button provides Horizontal line picture and Normal
picture alternately.
5. Press -/- - button to release horizontal line picture, and select the two other colors
which did not light in the above step with CHANNEL s, t buttons. Then tap VOL-
UME ; – /+ buttons so that three colors slightly light in the same level.
X To correct white balance in light area,
select GDRV and BDRV with CHANNEL
s, t buttons to adjust.
X To correct white balance in dark area,
perform fine adjustment of RCUT, GCUT
and BCUT.
Light area check
(to show white)
Dark area check
(to show black)
-
11
-
V/C system adjustment
No.
1
ADJUSTING ITEMS
AND POINTS
Cutoff adjustment and
white balance adjustment
RCUT
GCUT
BCUT
GDRV
BDRV
Screen VR
GENERAL ADJUSTMENTS
Sub contrast adjustment
2
(SCNT)
Sub brightness adjust-
3
ment
(BRTC)
ADJUSTMENT PROCEDURE
1) Setting to horizontal alignment, turn the screen VR to
stop where the brightness lines are slightly luminous.
(Adjustment shall be made so that they look almost
white.)
2) Cancel horizontal alignment.
3) Varying R, G and B CUTOFF, make white balance
adjustment in the dark area.
4) Adjusting G and B DRIVE, make white balance adjustment in the bright area.
5) Repeat procedures 3) and 4) if necessary.
Adjustable value:
Bright area: 11500K+0.0075uV
(103cd/m
Dark area: 10500K+0.0105uV
(17cd/m
2
)
2
)
1) Select SCNT in the sub data adjustment mode.
2) With TP-Y, set the amplitude from pedestal level to
white peak to 0.70±0.03 V (0-p).
1) Select BRTC in the sub data adjustment mode.
Adjust the number of black solid lines to 4±1.5.
REMARKS
No outside lighting shall be
allowed.
Measurement shall be
performed at the center of
CRT.
Receiver shall be in the
standard state.
Total white signal
Varying the level of input
signal, adjust the
brightness.
J-2ch sub brightness signal
DYNAMIC
J-2ch sub brightness signal
DYNAMIC
V/C system adjustment (Chassis adjusment)
No.
4
ADJUSTING ITEMS
AND POINTS
DW sub screen contrast
adjustment
(PCNT)
1) Select PCNT in the sub data adjustment mode.
2) With TP-Y, make adjustment so that the amplitude of
sub screen (right image) coincides with that of main
screen (left image).
ADJUSTMENT PROCEDURE
REMARKS
J-2ch for both main and sub
screens
Sub brightness signal
DYNAMIC
-
12
-
Circuit Adjustment (Procedure Manual for Deflection Adjustment)
Horizontal adjusment shall be made using E-12CH Philips pattern and DYNAMIC image mode.
<Adjustment procedure>
1) Using WID data, reduce the horizontal amplitude until a part of it is dropped out.
2) Using WID data, adjust the horizontal amplitude so that horizontal raster inevitably
contacts with CPT mask.
3) Using the following (Note 1) horizontal screen positional switch, adjust the horizontal raster position to the center position.
4) Using the horizontal amplitude
(WID) and horizontal phase
(HPOS), adjust the horizontal
amplitude so that the right and
left flags are just blinded.
The adjustment shall be made so that the right and left flags are just blinded.
5) Using PARA, TRAP, CNR and CPAR (or TCNR, BCNR or CSAW if necessary),
Right sideLeft side
adjust the screen distortion.
6) If necessary, make the horizontal amplitude adjustment again.
Screen position shall be
switched by inserting a
plug into the abo
ve pin.
(CENT should take the
first stage)
Horizontal adjustment
ADJUSTING ITEMS
AND POINTS
Hori-
zontal
For NTSC WIDE
Horizontal phase
(NHPO)
Horizontal amplitude
(NWID)
Side pin distortion
(NPAR)
* NTSC adjustment shall be made after PAL adjustment.
1) With domestic 13ch, WIDE
mode and DYNAMIC, adjust the
right and left bars to the fifth
center for horizontal phase
(NHPO) and horizontal amplitude (NWID).
2) With domestic 11ch, NPAR, NTRA, NCNR and NCPAR (or NTCNR, NBCNR or
Right and left bars shall be adjusted
to the fifth center.
NCSAW if necessary), adjust the screen distortion.
3) If necessary, make horizontal amplitude adjustment again.
-
14
-
Vertical adjustment
2
0
0
5
5
Verti-
cal
ADJUSTING ITEMS
AND POINTS
For PAL WIDE
Vertical amplitude
(HIT)
Vertical screen position
(TCNR)
Vertical linearity
(VLIN)
For NTSC WIDE
Vertical amplitude
(NHIT)
Vertical screen position
(NVPO)
ADJUSTMENT PROCEDURE
1) With E-12ch, WIDE mode, DYNAMIC and 100 Hz, adjust the vertical screen position (VPOS) and amplitude (HIT) as shown in the following figure:
Flags shall just be blinded.
GENERAL ADJUSTMENTS
Flags shall just be blinded.
2) With vertical linearity (VLIN), control the upper and lower balances to be optimal.
* NTSC adjustment shall be made after the PAL adjustment.
With domestic 13ch, WIDE mode and DYNAMIC, adjust the vertical screen position
(NVPO) and amplitude (NHIT) as shown in the following figure:
The circle of lion shall contact
with mask.
2
25
30
30
35
31
35
30
30
25
2
0
0
25
25
30
31
30
3
1
0
3
5
3
325
30
30
20
575300
35
30
525 LINE
35
45
50
1
3
The twelve center shall be adjusted to the mask.
-
15
-
Geomagnetic compensation (chassis adjustment)
ADJUSTING ITEMS
AND POINTS
1
Output voltage control
(GMF)
Horizontal adjustment* DQF adjustment shall be made in PAL WIDE mode.
ADJUSTING ITEMS
GENERAL ADJUSTMENTS
Hori-
zontal
AND POINTS
DQF output voltage
adjustment
ADJUSTMENT PROCEDURE
Conditions: User control for geomagnetic compensation: 0
Geomagnetic compensation coil: Unconnected
Perform voltage measurement at both ends of RJ06 and adjust the voltage to the following adjustable value with GMF of data adjustment mode:
0 ± 1V
ADJUSTMENT PROCEDURE
Measure the terminal voltage waveform of test pin (DF terminal) with 100:1 probe and
adjust the terminal voltage using L451 (horizontal amplitude coil: TLN2110AD).
Vp-p
1H
Adjust the above waveform by turning the core of L451 so as to obtain the following
voltage:
Note: Because the vertical cycle parabolic waveform is also of superposition, the
34": 1000 Vp-p
above voltage value shall be measured on the waveform.
Adopted signal: PAL E-12ch
-
16
-
CIRCUIT CHECK
HIGH VOLTAGE CHECK
CAUTION: There is no HIGH VOLTAGE ADJUSTMENT on this chassis. Checking should be done following the steps below.
1. Connect an accurate high voltage meter to the second anode of the picture tube.
2. Turn on the receiver. Set the BRIGHTNESS and CONTRAST controls to minimum (zero beam current).
3. High voltage must be measured below (B) kV.
Refer to table-1 for high voltage (B).
(See SETTING & ADJUSTING DATA on page 18)
4. Vary the BRIGHTNESS control to both extremes to be sure the high voltage does not exceed the limit under any conditions.
GENERAL ADJUSTMENTS
-
17
-
CHAPTER 2 SPECIFIC INFORMATIONS
SETTING & ADJUSTING DATA
SAFETY INSTRUCTIONS
HIGH VOLTAGE AT ZERO BEAM:
MAX HIGH VOLTAGE:
AC VOLTAGE
Table-1
SERVICE MODE
ADJUSTING ITEMS AND DATAS IN THE SERVICE MODE:
(A)
(B)
(C)
34"
30.5 kV
35.0 kV
220~240 V
SPECIFIC INFORMATIONS
ItemName of adjustmentItemName of adjustment
RCUTR CUTOFF 40H←
GCUTG CUTOFF40H←
BCUTB CUTOFF 40H←
GDRV/
RDRV
BDRVB DRIVE40H←
CNTXCONTRAST MAX7FH←
BRTCBRIGHTNESS CEN80H←
COLCSUB COLOR CEN NTSC00H←
TNTCSUB TINT CEN00H←
COLPSUB COLOR CEN PAL03H00H
COLSSUB COLOR CEN SECAMFDH←
SCNTSUB CONTRAST6AH22H
VOLSMSP DEM VOLS75H←
FVOLMSP DEM FVOL15H←
NVOLMSP DEM NVOL3CH←
NICLMSP DEM NICL03H←
NICHMSP DEM NICH0AH←
IDLMSP DEM IDL90H←
IDHMSP DEM IDHA0H←
HPOS576i 100Hz43H41H
VPOSV-POSITION8CH94H
HITHEIGHT43H41H
VLINV-LINEARITY0EH0CH
A. Program position selection
B. Sound system (see page 31)
C. Color system (see page 31)
A : Automatic, P : PAL, S : SECAM,
N4 : NTSC4.43 (MHz), N3 : NTSC3.58 (MHz)
If the color of a certain channel is abnormal, the
automatic color system selection (A) may have
malfunctioned, or the sound system selection is
wrong. In such a case, select another color and/or
sound system (see page 31).
D. Program position skip selection
Press the
or button to turn the program
position skip option on “
” or off “”.
The program position will then be skipped when
you select channels with the CH8 or CH9 button.
The “
” mark will appear beside a program
position number when you use the number button
on the remote control.
MENU
BackWatch TV
EXIT
Store
Manual tuning
Program
I
A
1
A
BCDEF
G
H
• First, use the Auto tuning feature to preset all the active channels in your area automatically. Then,
arrange the preset channels with the Manual tuning feature so that you can tune in only desired
channels.
• Use the Channel search operation if desired channels cannot be preset with the Auto tuning or if
you would like to preset channels to specific position numbers one by one.
To preset channels
Auto tuning
Press the MENU button, then
1
press the
display the SET UP menu.
Press the
select Auto tuning.
Press and hold the OK button
2
for several seconds to start
the automatic search.
The search will begin for all
available stations.
Bullet will move along the line as the search progresses.
DO NOT PRESS ANY BUTTONS WHILE THE AUTOMATIC
SEARCH IS IN PROGRESS.
If you make a mistake, simply repeat steps 1-2 to start
again from the beginning.
When the automatic search is complete, the TV will
3
automatically return to the first program position.
Press the CH8 or CH9 button to view the programmed
4
position.
<
or > button to
or button to
Language
Auto tuning
Manual tuning
Program sorting
Geomagnetic
MENU
Searching
Pos: 2
EXIT
BackWatch TV
Auto tuning
CancelEXIT
SET UP
0
English
Manual tuning
1
OK
OK
OK
2
3
Press the MENU button, then
<
press the
or > button to
display the SET UP menu.
Press the
or button to
select Manual tuning.
Press the OK button to display
the Manual tuning menu.
Press the
or button to
select the program position
you want to arrange.
Press the OK button to display
the breakdown menu.
<
Press the
or > button to
select an item, then press
or button to select
the
the item as shown below.
Language
Auto tuning
Manual tuning
Program sorting
Geomagnetic
MENU
Prog. Sys.
MENU
EXIT
BackWatch TV
Manual tuning
1I
2I
3I
4I
5I
6I
Select
EXIT
BackWatch TV
Manual tuning
1
I
A
MENU
BackWatch TV
Store
SET UP
0
Program
EXIT
English
Label
OK
OK
OK
SPECIFIC INFORMATIONS
-
21
-
E. Channel search operation
.
Press the
button to search down the band.
Press the
desired channel is displayed.
When a station/satellite is found, it will be
displayed.
F. Auto Fine Tuning
Press the
Tuning option On “
The Auto Fine Tuning feature automatically
corrects slight fluctuations when receiving signals
Manual Fine Tuning
While the Auto Fine Tuning turn Off “0”, press the
or button so that the better picture and sound
are obtained.
G. ANT ATT (Antenna attenuator)
Press the
option On “
interference occurs, set the ANT ATT to On.
H. Label
Station labels appear with the program position
display each time you turn on the TV, select a
channel, or press the CALL button.
button to search up the band or the
or button repeatedly until your
or button to turn the Auto Fine
” or Off “0”.
or button to turn the ANT ATT
” or Off “”, when visual
To change or create station labels:
1) Press the
or button repeatedly to select a
character for the first space, then press the
button.
>
SPECIFIC INFORMATIONS
*(blank space)
2) Repeat step 1 to enter the rest of the
characters. If you would like a blank space in
the label name, you must choose an empty
space from the list of characters.
Press the OK button to store your settings.
-
22
-
CHASSIS AND CABINET REPLACEMENT PARTS LIST
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY
PRECAUTION” AND “PRODUCT SAFETY NOTICE” ON PAGE 3 OF THIS MANUAL.
CAUTION: The international hazard symbols "" in the schematic diagram and the parts list designate com-
ponents which have special characteristics important for safety and should be replaced only with types identical to
those in the original circuit or specified in the parts list. The mounting position of replacements is to be identical with
originals. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE. Do not degrade
the safety of the receiver through improper servicing.
NOTICE:
•
The part number must be used when ordering parts, in order to assist in processing, be sure to include the
Model number and Description.
•
The PC board assembly with ∗ mark is no longer available after the end of the production.
Resistors ............... CF:Carbon FilmCC : Carbon CompositionMF : Metal Film
OMF : Oxide Metal FilmVR : Variable ResistorFR: Fusible Resistor
(All CD and PF capacitors are ±5%, 50V and all resistors, ±5%, 1/6W unless otherwise noted.)
Location
No.
Parts No. Description
CAPACITORS
C10124796479 ELECTROLYTIC, 35V 4.7UF M
C10224793221 ELECTROLYTIC, 10V 220UF M
C10324109103 CERAMIC CHIP, 50V B 0.01UF K
C10424109103 CERAMIC CHIP, 50V B 0.01UF K
C10524109102 CERAMIC CHIP, 50V B 1000PF K
C10624797479 ELECTROLYTIC, 50V 4.7UF M
C10724794221 ELECTROIYTIC 04G, 16V 220UF M
C10824793221 ELECTROLYTIC, 10V 220UF M
C10924100104 CERAMIC CHIP, 25V F 0.1UF Z
C11024794101 ELECTROLYTIC, 16V 100UF M
C20524092539 CERAMIC CHIP, 10V F 2.2UF Z
C20624619042 ELEC. CHIP, 16V 22UF M 3A
C30424503041 PLASTIC FILM , 63V 0.1UF J
C30824669221 ELECTROLYTIC, 50V 220UF M 3A
C31024667102 ELECTROLYTIC, 25V 1000UF M 3A
C31324082057 PLASTIC FILM, 100V 0.22UF J
C31424667221 ELECTROLYTIC CE04Q, 25V 220UF M 3A
C31524109332 CERAMIC CHIP, 50V B 3300PF K
C31924503053 PLASTIC FILM, 63V 1UF J
C32024667221 ELECTROLYTIC CE04Q, 25V 220UF M 3A
C32124503051 PLASTIC FILM, 63V 0.68UF J
C32224503053 PLASTIC FILM, 63V 1UF J
C32324503049 PLASTIC FILM, 63V 0.47UF J
C32524591223 PLASTIC FILM, 50V 0.022UF J
C32624669010 ELECTROLYTIC, 50V 1UF M 3A
C32724073041 ELECTROLYTIC, 16V 470UF M 3A
C32924591183 PLASTIC FILM, 50V 0.018UF J
C33124590103 PLASTIC FILM, 50V 0.01UF J
C33224109473 CERAMIC CHIP, 25V B 0.047UF K
C33324109102 CERAMIC CHIP, 50V B 1000PF K
C33624108101 CERAMIC CHIP, 50V SL 100PF J
C36224591682 PLASTIC FILM, 50V 6800PF J
C36624082275 PLASTIC FILM CQ922 M 100V 82000PF J
C37024666100 ELECTROLYTIC, 10V 10UF M 3A
C39224085981 ELEC. NONPOLAR CE04J 16V 10UF M 11L NP
C39324109103 CERAMIC CHIP, 50V B 0.01UF K
C39624503065 PLASTIC FILM, 1800VH 1800PF H
C41324214392 CERAMIC DISC, 500V B 3900PF K
C41624676330 ELECTROLYTIC, 100V 33UF M 3A
C41724214391 CERAMIC DISC, 500V B 390PF K
C41824667221 ELECTROLYTIC CE04Q, 25V 220UF M 3A
C41924590102 PLASTIC FILM, 50V 1000PF J
C42824503192 PLASTIC FILM, 400V 0.15UF J
Location
No.
C43024539334 PLASTIC FILM, 50V 0.33UF J
C43124539104 PLASTIC FILM, 50V 0.1UF J
C43224666100 ELECTROLYTIC, 10V 10UF M 3A
C43924503457 PLASTIC FILM CQ92 T 400V 56000PF J
C44224503192 PLASTIC FILM, 400V 0.15UF J
C44324503195 PLASTIC FILM, 1800VH 5100PF H
C44424503195 PLASTIC FILM, 1800VH 5100PF H
C44524095804 PLASTIC FILM, 400V 0.056UF J
C44624640020 ELECTROLYTIC CE04Q 250V 33UF M H-R
C44824073118 ELECTROLYTIC, 160V 33UF M
C45024214222 CERAMIC DISC, 500V B 2200PF K
C45124214222 CERAMIC DISC, 500V B 2200PF K
C45224820103 PLASTIC FILM, 630V 0.01UF J
C46124820123 PLASTIC FILM, 630V 0.012UF J
C46424503149 PLASTIC FILM, 250V 3.3UF
C46524591563 PLASTIC FILM, 50V 0.056UF J
C46624679220 ELECTROLYTIC, 250V 22UF M 3A
C46724820123 PLASTIC FILM, 630V 0.012UF J
C46924591222 PLASTIC FILM, 50V 2200PF J
C47024766220 ELECTROLYTIC, 50V 22UF M
C47124766479 ELECTROLYTIC, 50V 4.7UF M
C47224503049 PLASTIC FILM, 63V 0.47UF J
C47624214471 CERAMIC DISC, 500V B 470PF K
C47724666220 ELECTROLYTIC, 16V 22UF M 3A
C48224109122 CERAMIC CHIP, 50V B 1200PF K
C48824666100 ELECTROLYTIC, 10V 10UF M 3A
C50524014104 CERAMIC CHIP, 16V F 0.1UF Z
C51224015103 CERAMIC CHIP, 16V B 0.01UF K
C51324015103 CERAMIC CHIP, 16V B 0.01UF K
C52024092616 CERAMIC CHIP, 16V B 0.33UF K
C53124014104 CERAMIC CHIP, 16V F 0.1UF Z
C53224014104 CERAMIC CHIP, 16V F 0.1UF Z
C53324014104 CERAMIC CHIP, 16V F 0.1UF Z
C53424014104 CERAMIC CHIP, 16V F 0.1UF Z
C53624014104 CERAMIC CHIP, 16V F 0.1UF Z
C53724014104 CERAMIC CHIP, 16V F 0.1UF Z
C54324014104 CERAMIC CHIP, 16V F 0.1UF Z
C54424014104 CERAMIC CHIP, 16V F 0.1UF Z
C54524014104 CERAMIC CHIP, 16V F 0.1UF Z
C54724015103 CERAMIC CHIP, 16V B 0.01UF K
C54824619157 MENJISSOU TYP 16V100U
C55824015103 CERAMIC CHIP, 16V B 0.01UF K
C56324092789 CERAMIC CHIP, 6.3V B 1UF K
C56424092856 CERAMIC CHIP CK732B 16V 2.2UF K
Parts No. Description
SPECIFIC INFORMATIONS
-
23
-
Location
No.
Parts No. Description
Location
No.
Parts No. Description
SPECIFIC INFORMATIONS
C56524092785 CERAMIC CHIP, 10V B 0.47UF K
C56824014104 CERAMIC CHIP, 16V F 0.1UF Z
C57224014104 CERAMIC CHIP, 16V F 0.1UF Z
C60124797100 ELECTROLYTIC, 50V 10UF M
C60224591102 PLASTIC FILM, 50V 1000PF J
C60324669101 ELECTROLYTIC, 50V 100UF M 3A
C60524109103 CERAMIC CHIP, 50V B 0.01UF K
C60724797470 ELECTROLYTIC 04G, 50V 47UF M
C61324666471 ELECTROLYTIC 04Q, 16V 470UF M 3A
C61524666220 ELECTROLYTIC, 16V 22UF M 3A
C62224085944 ELECTROLYTIC, NONPOLAR, 50V 2.2UF M 11L
C62524085944 ELECTROLYTIC, NONPOLAR, 50V 2.2UF M 11L
C62824669220 ELECTROLYTIC, 04Q 50V 22UF M 3A
C63324669101 ELECTROLYTIC, 50V 100UF M 3A
C63424109103 CERAMIC CHIP, 50V B 0.01UF K
C64024797479 ELECTROLYTIC, 50V 4.7UF M
C64124797479 ELECTROLYTIC, 50V 4.7UF M
C64224669229 ELECTROLYTIC, 50V 2.2UF M 3A
C64324669229 ELECTROLYTIC, 50V 2.2UF M 3A
C64424105221 CERAMIC CHIP, 50V CH 220PF J
C64524105221 CERAMIC CHIP, 50V CH 220PF J
C64624794102 ELECTROLYTIC, 16V 1000UF M
C64724794101 ELECTROLYTIC, 16V 100UF M
C64824794101 ELECTROLYTIC, 16V 100UF M
C65124815103 CERAMIC CHIP, 50V B 10000PF K
C66024073034 ELECTROLYTIC, 16V 10UF M 3A
C66124073082 ELECTROLYTIC, 50V 2.2UF M 3A
C66224073082 ELECTROLYTIC, 50V 2.2UF M 3A
C66324591102 PLASTIC FILM, 50V 1000PF J
C66424591102 PLASTIC FILM, 50V 1000PF J
C66524797100 ELECTROLYTIC, 50V 10UF M
C66624590104 PLASTIC FILM, 50V 0.1UF J
C67124073084 ELECTROLYTIC, 50V 4.7UF M 3A
C67224073084 ELECTROLYTIC, 50V 4.7UF M 3A
C67324073086 ELECTROLYTIC, 50V 10UF M 3A
C67524667470 ELECTROLYTIC CE04Q, 25V 47UF M 3A
C67624669479 ELECTROLYTIC, 50V 4.7UF M 3A
C67724503042 PLASTIC FILM, 63V 0.12UF J
C67824503041 PLASTIC FILM , 63V 0.1UF J
C67924503041 PLASTIC FILM , 63V 0.1UF J
C68024669222 ELECTROLYTIC, 50V 2200UF M 3A
C68124668102 ELECTROLYTIC, 35V 1000UF M 3A
C68224668102 ELECTROLYTIC, 35V 1000UF M 3A
C68324668102 ELECTROLYTIC, 35V 1000UF M 3A
C68424109103 CERAMIC CHIP, 50V B 0.01UF K
C69124073034 ELECTROLYTIC, 16V 10UF M 3A
C70424591822 PLASTIC FILM, 50V 8200PF J
C70524232103 CERAMIC DISC, 50V F 0.01UF Z
C70724794470 ELECTROLYTIC, 16V 47UF M
C71224666470 ELECTORLYTIC, 16V 47UF M 3A
C71324709100 ELECTROLYTIC, 200V 10UF M
C71424436101 CERAMIC DISC, 50V SL 100PF J
C71524214472 CERAMIC DISC, 500V B 4700PF K
C71624436101 CERAMIC DISC, 50V SL 100PF J
C71724214472 CERAMIC DISC, 500V B 4700PF K
C71824766470 ELECTROLYTIC, 50V 47UF M
C71924435560 CERAMIC DISC, 500V SL 56PF J
C72024709100 ELECTROLYTIC, 200V 10UF M
C72124797470 ELECTROLYTIC 04G, 50V 47UF M
C72624212102 CERAMIC DISC, 50V B 1000PF K
C80124503507 PLASTIC FILM, AC275V 0.22UF K
C80224503507 PLASTIC FILM, AC275V 0.22UF K
C80524092281 CERAMIC DISC, AC250V E 4700PF
C80624092281 CERAMIC DISC, AC250V E 4700PF
C80724503049 PLASTIC FILM, 63V 0.47UF J
C80824667101 ELECTROLYTIC, 25V 100UF M 3A
C80924503041 PLASTIC FILM , 63V 0.1UF J
C81024073106 400V680UF LLQ2G681MHSET
C81324092563 CERAMIC DISC, AC250V B 220PF K
C81424092563 CERAMIC DISC, AC250V B 220PF K
C81524092567 CERAMIC DISC, AC250V E 1000PF M
C81624668339 ELECTROLYTIC, 35V 3.3UF M 3A
C81724092339 CERAMIC DISC, 2KV 330PF K
C81824095931 PLASTIC FILM, 1250VH 2200PF J
C82024092565 CERAMIC DISC, AC250V B 470PF K
C82124214471 CERAMIC DISC, 500V B 470PF K
C82224619157 MENJISSOU TYP 16V100U
C82324214471 CERAMIC DISC, 500V B 470PF K
C82424014104 CERAMIC CHIP, 16V F 0.1UF Z
C82524503041 PLASTIC FILM , 63V 0.1UF J
C82624014104 CERAMIC CHIP, 16V F 0.1UF Z
C82824092794 CERAMIC CHIP CK732B 6.3V 10UF M
C82924014104 CERAMIC CHIP, 16V F 0.1UF Z @U902
24212222 CERAMIC DISC, 50V B 2200PF K @U904
C83324669229 ELECTROLYTIC, 50V 2.2UF M 3A
C83424503047 PLASTIC FILM, 63V 0.33UF J
C83524073150 ELECTROLYTIC CE04P 16V 56UF M 3A
C83624762222 ELECTROLYTIC, 10V 2200UF M 3D
C84024073098 ELECTROLYTIC, 450V 4.7UF M 3A
C84124073043 ELECTROLYTIC, 16V 2200UF M 3A
C84224503041 PLASTIC FILM , 63V 0.1UF J
C84324092469 CERAMIC DISC, 2KV B 100PF K
C84424073038 ELECTROLYTIC, 16V 100UF M 3A
C84524766229 ELECTROLYTIC, 50V 2.2UF M
C88424073215 ELECTROLYTEC CE04Q 160V 220UF M
C88724214471 CERAMIC DISC, 500V B 470PF K
C89024073172 ELECTROLYTIC CE04P 25V 1000UF M 3A
C89124073176 ELECTROLYTIC CE04P 25V 2200UF M 3A
C89324092337 CERAMIC DISC, 2KV 220PF K
C89524073209 ELECTROLYTIC CE04P 50V 1000UF M 3A
C89624214471 CERAMIC DISC, 500V B 470PF K
C89724073172 ELECTROLYTIC CE04P 25V 1000UF M 3A
C89824591102 PLASTIC FILM, 50V 1000PF J
C89924214471 CERAMIC DISC, 500V B 470PF K
C90224092353 CERAMIC DISC, 2KV 4700PF K
C90424436561 CERAMIC DISC, 50V SL 560PF J
C90524436471 CERAMIC DISC, 50V SL 470PF J
C90724436561 CERAMIC DISC, 50V SL 560PF J
C90924073120 ELECTRPLYTIC, 250V 33UF, 250YXF33M
C91024669478 ELECTROLYTIC, 50V 0.47UF M 3A
C91124203100 ELECTORLYTIC, 16V 10UF M 7L 3A
C91224073042 ELECTROLYTIC, 04P 16V 1000UF M 3A
C91324666102 ELECTROLYTIC, 16V 1000UF M 3A
C91424232103 CERAMIC DISC, 50V F 0.01UF Z
C91824539104 PLASTIC FILM, 50V 0.1UF J
C91924539104 PLASTIC FILM, 50V 0.1UF J
C93124214101 CERAMIC DISC, 500V B 100PF K
C81124092567 CERAMIC DISC, AC250V E 1000PF M
C81224092567 CERAMIC DISC, AC250V E 1000PF M @U905A
24503041 PLASTIC FILM , 63V 0.1UF J @U904
C210224013100 CERAMIC CHIP CC73CH 50V 10PF D
C210324013100 CERAMIC CHIP CC73CH 50V 10PF D
C210424013100 CERAMIC CHIP CC73CH 50V 10PF D
C211024014104 CERAMIC CHIP, 16V F 0.1UF Z
C310024667102 ELECTROLYTIC, 25V 1000UF M 3A
C410024109103 CERAMIC CHIP, 50V B 0.01UF K
C410124092859 CERAMIC CHIP CK73B 10V 1UF K
C410224108150 CERAMIC CHIP, 50V SL 15PF J
C410324092730 CERAMIC CHIP, 16V B 0.1UF K
C410424092730 CERAMIC CHIP, 16V B 0.1UF K
C411224015103 CERAMIC CHIP, 16V B 0.01UF K
C421124539104 PLASTIC FILM, 50V 0.1UF J
C440124619158 MENJISSOU TYP 16V220U
C440224015103 CERAMIC CHIP, 16V B 0.01UF K
C440324092789 CERAMIC CHIP, 6.3V B 1UF K
C440424015103 CERAMIC CHIP, 16V B 0.01UF K
C440524014104 CERAMIC CHIP, 16V F 0.1UF Z
C440624015103 CERAMIC CHIP, 16V B 0.01UF K
-
24
-
Location
No.
Parts No. Description
Location
No.
Parts No. Description
C442724092789 CERAMIC CHIP, 6.3V B 1UF K
C446024092796 CERAMIC CHIP CK732B 50V 220000PF K
C446124092796 CERAMIC CHIP CK732B 50V 220000PF K
C447624013100 CERAMIC CHIP CC73CH 50V 10PF D
C460224109122 CERAMIC CHIP, 50V B 1200PF K
C460324000445 CHIP JUMPER, 1608TYPE
C469024109223 CERAMIC CHIP, 25V B 0.022UF K
C469124109822 CERAMIC CHIP, 50V B 8200PF K
C471024092859 CERAMIC CHIP CK73B 10V 1UF K
C471124092785 CERAMIC CHIP, 10V B 0.47UF K
C501224014104 CERAMIC CHIP, 16V F 0.1UF Z
C501424014104 CERAMIC CHIP, 16V F 0.1UF Z
C501524092738 CERAMIC CHIP, 25V B 0.47UF K
C501624014104 CERAMIC CHIP, 16V F 0.1UF Z
C502024015103 CERAMIC CHIP, 16V B 0.01UF K
C502124015104 CERAMIC CHIP CK73B 6.3V 100,000PF K
C502224015104 CERAMIC CHIP CK73B 6.3V 100,000PF K
C502324015104 CERAMIC CHIP CK73B 6.3V 100,000PF K
C503024619157 MENJISSOU TYP 16V100U
C508024092789 CERAMIC CHIP, 6.3V B 1UF K
C509024619157 MENJISSOU TYP 16V100U
C541124015103 CERAMIC CHIP, 16V B 0.01UF K
C541224015103 CERAMIC CHIP, 16V B 0.01UF K
C541324013180 CERAMIC CHIP, 50V CH 18PF J
C541424015102 CERAMIC CHIP, 50V B 1000PF K
C541524013050 CERAMIC CHIP CC73CH 50V 5PF C
C544024015103 CERAMIC CHIP, 16V B 0.01UF K
C544124014104 CERAMIC CHIP, 16V F 0.1UF Z
C544224014104 CERAMIC CHIP, 16V F 0.1UF Z
C544324014104 CERAMIC CHIP, 16V F 0.1UF Z
C544524092738 CERAMIC CHIP, 25V B 0.47UF K
C544824014104 CERAMIC CHIP, 16V F 0.1UF Z
C544924014104 CERAMIC CHIP, 16V F 0.1UF Z
C545024014104 CERAMIC CHIP, 16V F 0.1UF Z
C545224015103 CERAMIC CHIP, 16V B 0.01UF K
C545424092573 CERAMIC CHIP, 16V B 0.47UF K
C545624013330 CERAMIC CHIP, 50V CH 33PF J
C545724013330 CERAMIC CHIP, 50V CH 33PF J
C545824092573 CERAMIC CHIP, 16V B 0.47UF K
C545924014104 CERAMIC CHIP, 16V F 0.1UF Z
C546224014104 CERAMIC CHIP, 16V F 0.1UF Z
C546324013040 CERAMIC CHIP CC73CH 50V 4PF C
C546424014104 CERAMIC CHIP, 16V F 0.1UF Z
C810024092794 CERAMIC CHIP CK732B 6.3V 10UF M
C810124014104 CERAMIC CHIP, 16V F 0.1UF Z
C810224014104 CERAMIC CHIP, 16V F 0.1UF Z
C810324092794 CERAMIC CHIP CK732B 6.3V 10UF M
C810424014104 CERAMIC CHIP, 16V F 0.1UF Z
C810524014104 CERAMIC CHIP, 16V F 0.1UF Z
C810624092747 CERAMIC CHIP, 50V B 4.7UF K
C810724092794 CERAMIC CHIP CK732B 6.3V 10UF M
C810824014104 CERAMIC CHIP, 16V F 0.1UF Z
C810924014104 CERAMIC CHIP, 16V F 0.1UF Z
C811024092747 CERAMIC CHIP, 50V B 4.7UF K
C811124092794 CERAMIC CHIP CK732B 6.3V 10UF M
C811224014104 CERAMIC CHIP, 16V F 0.1UF Z
C811324014104 CERAMIC CHIP, 16V F 0.1UF Z
C811524092794 CERAMIC CHIP CK732B 6.3V 10UF M
C811624015104 CERAMIC CHIP CK73B 6.3V 100,000PF K
C811724092794 CERAMIC CHIP CK732B 6.3V 10UF M
C811824015104 CERAMIC CHIP CK73B 6.3V 100,000PF K
C811924619147 6.3V 47U UWXOJ470MCR1GB
C812024619147 6.3V 47U UWXOJ470MCR1GB
C812124619147 6.3V 47U UWXOJ470MCR1GB
C812324015104 CERAMIC CHIP CK73B 6.3V 100,000PF K
C812424015104 CERAMIC CHIP CK73B 6.3V 100,000PF K
C812724092795 CERAMIC CHIP CK73B 6.3V 2.2UP K
C812824619147 6.3V 47U UWXOJ470MCR1GB
C812924092795 CERAMIC CHIP CK73B 6.3V 2.2UP K
C813124092795 CERAMIC CHIP CK73B 6.3V 2.2UP K
C813224092795 CERAMIC CHIP CK73B 6.3V 2.2UP K
C813324092795 CERAMIC CHIP CK73B 6.3V 2.2UP K
C813424092795 CERAMIC CHIP CK73B 6.3V 2.2UP K
C813524092795 CERAMIC CHIP CK73B 6.3V 2.2UP K
C813624092795 CERAMIC CHIP CK73B 6.3V 2.2UP K
C813724092795 CERAMIC CHIP CK73B 6.3V 2.2UP K
C813824092795 CERAMIC CHIP CK73B 6.3V 2.2UP K
C813924092795 CERAMIC CHIP CK73B 6.3V 2.2UP K
C814124092795 CERAMIC CHIP CK73B 6.3V 2.2UP K
C834124667100 ELECTROLYTIC, 16V 10UF M 3A
C834224503047 PLASTIC FILM, 63V 0.33UF J
C834424503047 PLASTIC FILM, 63V 0.33UF J
C834524503047 PLASTIC FILM, 63V 0.33UF J
C834724665220 ELECTROLYTIC, 10V 22UF M 3A
C834824073150 ELECTROLYTIC CE04P 16V 56UF M 3A
C834924666100 ELECTROLYTIC, 10V 10UF M 3A
C835024666100 ELECTROLYTIC, 10V 10UF M 3A
C835124073150 ELECTROLYTIC CE04P 16V 56UF M 3A
C835224666100 ELECTROLYTIC, 10V 10UF M 3A
CA0124015102 CERAMIC CHIP, 50V B 1000PF K
CA0324014104 CERAMIC CHIP, 16V F 0.1UF Z
CA0424014104 CERAMIC CHIP, 16V F 0.1UF Z
CA0524092794 CERAMIC CHIP CK732B 6.3V 10UF M
CA0624092538 CERAMIC CHIP, 10V F 1UF Z
CA0724109102 CERAMIC CHIP, 50V B 1000PF K
CA0824092538 CERAMIC CHIP, 10V F 1UF Z
CA0924109102 CERAMIC CHIP, 50V B 1000PF K
CA1024014104 CERAMIC CHIP, 16V F 0.1UF Z
CA1124014104 CERAMIC CHIP, 16V F 0.1UF Z
CA1224014104 CERAMIC CHIP, 16V F 0.1UF Z
CA1324014104 CERAMIC CHIP, 16V F 0.1UF Z
CA1424092538 CERAMIC CHIP, 10V F 1UF Z
CA1524109102 CERAMIC CHIP, 50V B 1000PF K
CA1624013220 CERAMIC CHIP, 50V CH 22PF J
CA1724013220 CERAMIC CHIP, 50V CH 22PF J
CA1824014104 CERAMIC CHIP, 16V F 0.1UF Z
CA1924014104 CERAMIC CHIP, 16V F 0.1UF Z
CA2024014104 CERAMIC CHIP, 16V F 0.1UF Z
CA2124092538 CERAMIC CHIP, 10V F 1UF Z
CA2224109102 CERAMIC CHIP, 50V B 1000PF K
CA2324014104 CERAMIC CHIP, 16V F 0.1UF Z
CA2424014104 CERAMIC CHIP, 16V F 0.1UF Z
CA2524014104 CERAMIC CHIP, 16V F 0.1UF Z
CA2624014104 CERAMIC CHIP, 16V F 0.1UF Z
CA2724014104 CERAMIC CHIP, 16V F 0.1UF Z
CA2924014104 CERAMIC CHIP, 16V F 0.1UF Z
CA3024014104 CERAMIC CHIP, 16V F 0.1UF Z
CA3124014104 CERAMIC CHIP, 16V F 0.1UF Z
CA3224014104 CERAMIC CHIP, 16V F 0.1UF Z
CA3324014104 CERAMIC CHIP, 16V F 0.1UF Z
CA3424014104 CERAMIC CHIP, 16V F 0.1UF Z
CA3524014104 CERAMIC CHIP, 16V F 0.1UF Z
CA3624014104 CERAMIC CHIP, 16V F 0.1UF Z
CA3724014104 CERAMIC CHIP, 16V F 0.1UF Z
CA3824014104 CERAMIC CHIP, 16V F 0.1UF Z
CA4024015103 CERAMIC CHIP, 16V B 0.01UF K
CA4124015103 CERAMIC CHIP, 16V B 0.01UF K
CA4224092628 CERAMIC CHIP, 0J B 10UF K
CA4324092794 CERAMIC CHIP CK732B 6.3V 10UF M
CA4424015103 CERAMIC CHIP, 16V B 0.01UF K
CA4524015103 CERAMIC CHIP, 16V B 0.01UF K
CA4724015222 CERAMIC CHIP, 50V B 2200PF K
CA4824015222 CERAMIC CHIP, 50V B 2200PF K
CA4924109152 CERAMIC CHIP, 50V B 1500PF K
CA5024015332 CERAMIC CHIP, 50V B 3300PF K
CA5124109152 CERAMIC CHIP, 50V B 1500PF K
CA5224015332 CERAMIC CHIP, 50V B 3300PF K
CA5324015104 CERAMIC CHIP CK73B 6.3V 100,000PF K
SPECIFIC INFORMATIONS
-
25
-
Location
No.
Parts No. Description
Location
No.
Parts No. Description
SPECIFIC INFORMATIONS
CA5424015104 CERAMIC CHIP CK73B 6.3V 100,000PF K
CA5524092621 CERAMIC CHIP, 10V B 1UF K
CA5624092621 CERAMIC CHIP, 10V B 1UF K
CA5724014104 CERAMIC CHIP, 16V F 0.1UF Z
CA5824014104 CERAMIC CHIP, 16V F 0.1UF Z
CA5924014104 CERAMIC CHIP, 16V F 0.1UF Z
CA6024014104 CERAMIC CHIP, 16V F 0.1UF Z
CA6124092789 CERAMIC CHIP, 6.3V B 1UF K
CA6224013680 CERAMIC CHIP, 50V CH 68PF J
CA6324013220 CERAMIC CHIP, 50V CH 22PF J
CA6624092628 CERAMIC CHIP, 0J B 10UF K
CA6724619147 6.3V 47U UWXOJ470MCR1GB
CA8024015105 CHIP CERA CAP B 6.3V 105K
CA40424015103 CERAMIC CHIP, 16V B 0.01UF K
CB0124794470 ELECTROLYTIC, 16V 47UF M
CC0124109102 CERAMIC CHIP, 50V B 1000PF K
CC0224109102 CERAMIC CHIP, 50V B 1000PF K
CC0324109102 CERAMIC CHIP, 50V B 1000PF K
CC0424109102 CERAMIC CHIP, 50V B 1000PF K
CC0524109102 CERAMIC CHIP, 50V B 1000PF K
CC0624109102 CERAMIC CHIP, 50V B 1000PF K
CC0724109102 CERAMIC CHIP, 50V B 1000PF K
CC0824109102 CERAMIC CHIP, 50V B 1000PF K
CC0924109102 CERAMIC CHIP, 50V B 1000PF K
CC1024109102 CERAMIC CHIP, 50V B 1000PF K
CC1124109102 CERAMIC CHIP, 50V B 1000PF K @U903
24212102 CERAMIC DISC, 50V B 1000PF K @U905A
CC1224109102 CERAMIC CHIP, 50V B 1000PF K @U903
24212102 CERAMIC DISC, 50V B 1000PF K @U905A
CC1324232103 CERAMIC DISC, 50V F 0.01UF Z
CC1424232103 CERAMIC DISC, 50V F 0.01UF Z
CJ0124503041 PLASTIC FILM , 63V 0.1UF J
CJ0224666470 ELECTORLYTIC, 16V 47UF M 3A
CJ0324503041 PLASTIC FILM , 63V 0.1UF J
CJ0424666470 ELECTORLYTIC, 16V 47UF M 3A
CJ0524794101 ELECTROLYTIC, 16V 100UF M
CR1224014104 CERAMIC CHIP, 16V F 0.1UF Z
CR1324014104 CERAMIC CHIP, 16V F 0.1UF Z
CR1424014104 CERAMIC CHIP, 16V F 0.1UF Z
CR1524014104 CERAMIC CHIP, 16V F 0.1UF Z
CR1624014104 CERAMIC CHIP, 16V F 0.1UF Z
CR1724014104 CERAMIC CHIP, 16V F 0.1UF Z
CS2024797478 ELECTROLYTIC, 50V 0.47UF M
CS2524797478 ELECTROLYTIC, 50V 0.47UF M
CS3024794100 ELECTROLYTIC, 16V 10UF M
CS3124794100 ELECTROLYTIC, 16V 10UF M
CS3224794100 ELECTROLYTIC, 16V 10UF M
CS3324794100 ELECTROLYTIC, 16V 10UF M
CS4024092538 CERAMIC CHIP, 10V F 1UF Z
CS4124092538 CERAMIC CHIP, 10V F 1UF Z
CS4224092538 CERAMIC CHIP, 10V F 1UF Z
CS4324092538 CERAMIC CHIP, 10V F 1UF Z
CS4424092538 CERAMIC CHIP, 10V F 1UF Z
CS4524092538 CERAMIC CHIP, 10V F 1UF Z
CS4624092538 CERAMIC CHIP, 10V F 1UF Z
CS4724092538 CERAMIC CHIP, 10V F 1UF Z
CS4824092538 CERAMIC CHIP, 10V F 1UF Z
CS4924092538 CERAMIC CHIP, 10V F 1UF Z
CS5424092538 CERAMIC CHIP, 10V F 1UF Z
CS5524092538 CERAMIC CHIP, 10V F 1UF Z
CS5624092538 CERAMIC CHIP, 10V F 1UF Z
CS5724794470 ELECTROLYTIC, 16V 47UF M
CS6424794220 ELECTROLYTIC, 16V 22UF M
CV0124794101 ELECTROLYTIC, 16V 100UF M
CV0224100104 CERAMIC CHIP, 25V F 0.1UF Z
CV0324794101 ELECTROLYTIC, 16V 100UF M
CV0424100104 CERAMIC CHIP, 25V F 0.1UF Z
CV0524794101 ELECTROLYTIC, 16V 100UF M
CV0624100104 CERAMIC CHIP, 25V F 0.1UF Z
CV1124092731 CERAMIC CHIP, 16V B 1UF K
CV1224092731 CERAMIC CHIP, 16V B 1UF K
CV1324100104 CERAMIC CHIP, 25V F 0.1UF Z
CV1424100104 CERAMIC CHIP, 25V F 0.1UF Z
CV1524100104 CERAMIC CHIP, 25V F 0.1UF Z
CV1624100104 CERAMIC CHIP, 25V F 0.1UF Z
CV1724092731 CERAMIC CHIP, 16V B 1UF K
CV1824100104 CERAMIC CHIP, 25V F 0.1UF Z
CV1924092731 CERAMIC CHIP, 16V B 1UF K
CV2024100104 CERAMIC CHIP, 25V F 0.1UF Z
CV2124100104 CERAMIC CHIP, 25V F 0.1UF Z
CV2224100104 CERAMIC CHIP, 25V F 0.1UF Z
CV2324092731 CERAMIC CHIP, 16V B 1UF K
CV2424100104 CERAMIC CHIP, 25V F 0.1UF Z
CV2524100104 CERAMIC CHIP, 25V F 0.1UF Z
CV2824092731 CERAMIC CHIP, 16V B 1UF K
CV2924092731 CERAMIC CHIP, 16V B 1UF K
CV3024092731 CERAMIC CHIP, 16V B 1UF K
CV3124092731 CERAMIC CHIP, 16V B 1UF K
CV3224092731 CERAMIC CHIP, 16V B 1UF K
CV3324092731 CERAMIC CHIP, 16V B 1UF K
CV4024100104 CERAMIC CHIP, 25V F 0.1UF Z
CV4124100104 CERAMIC CHIP, 25V F 0.1UF Z
CV4824212102 CERAMIC DISC, 50V B 1000PF K
CV5024232103 CERAMIC DISC, 50V F 0.01UF Z
CV5324092621 CERAMIC CHIP, 10V B 1UF K
CV5724794101 ELECTROLYTIC, 16V 100UF M
CV48124100104 CERAMIC CHIP, 25V F 0.1UF Z
CV48224794101 ELECTROLYTIC, 16V 100UF M
CV48324794471 ELECTROLYTIC, 16V 470UF M
CX10524619157 MENJISSOU TYP 16V100U
CX10624015103 CERAMIC CHIP, 16V B 0.01UF K
CX11124014104 CERAMIC CHIP, 16V F 0.1UF Z
CX11224014104 CERAMIC CHIP, 16V F 0.1UF Z
CX11324014104 CERAMIC CHIP, 16V F 0.1UF Z
CX11424015105 CHIP CERA CAP B 6.3V 105K
CX11524015105 CHIP CERA CAP B 6.3V 105K
CX11624015105 CHIP CERA CAP B 6.3V 105K
CX11724015105 CHIP CERA CAP B 6.3V 105K
CX11824015105 CHIP CERA CAP B 6.3V 105K
CX11924015105 CHIP CERA CAP B 6.3V 105K
CX12024015105 CHIP CERA CAP B 6.3V 105K
CX12124015105 CHIP CERA CAP B 6.3V 105K
CX12224015105 CHIP CERA CAP B 6.3V 105K
CX12324015105 CHIP CERA CAP B 6.3V 105K
CX12424015105 CHIP CERA CAP B 6.3V 105K
CX12524015105 CHIP CERA CAP B 6.3V 105K
CX12624015105 CHIP CERA CAP B 6.3V 105K
CX12724015105 CHIP CERA CAP B 6.3V 105K
CX12824015105 CHIP CERA CAP B 6.3V 105K
CX12924015105 CHIP CERA CAP B 6.3V 105K
CX13024015105 CHIP CERA CAP B 6.3V 105K
CX13124015105 CHIP CERA CAP B 6.3V 105K
CX13224015105 CHIP CERA CAP B 6.3V 105K
CX13324015105 CHIP CERA CAP B 6.3V 105K
CX13424015105 CHIP CERA CAP B 6.3V 105K
CX13524015105 CHIP CERA CAP B 6.3V 105K
CX14824015105 CHIP CERA CAP B 6.3V 105K
CX20124619040 ELEC. CHIP, 16V 10UF M 3A
CX20224014104 CERAMIC CHIP, 16V F 0.1UF Z
CX20324014104 CERAMIC CHIP, 16V F 0.1UF Z
CX20424619040 ELEC. CHIP, 16V 10UF M 3A
CX20524014104 CERAMIC CHIP, 16V F 0.1UF Z
CX33124014104 CERAMIC CHIP, 16V F 0.1UF Z
CX33224092747 CERAMIC CHIP, 50V B 4.7UF K
CX33324092747 CERAMIC CHIP, 50V B 4.7UF K
CX33424014104 CERAMIC CHIP, 16V F 0.1UF Z
CX33724092747 CERAMIC CHIP, 50V B 4.7UF K
CX33824014104 CERAMIC CHIP, 16V F 0.1UF Z
-
26
-
Location
No.
Parts No. Description
Location
No.
Parts No. Description
CX33924015105 CHIP CERA CAP B 6.3V 105K
CX34024015105 CHIP CERA CAP B 6.3V 105K
CX34124092795 CERAMIC CHIP CK73B 6.3V 2.2UP K
CX34224092795 CERAMIC CHIP CK73B 6.3V 2.2UP K
CX40124619157 MENJISSOU TYP 16V100U
CX40224015104 CERAMIC CHIP CK73B 6.3V 100,000PF K
CX40324619157 MENJISSOU TYP 16V100U
CX40424015103 CERAMIC CHIP, 16V B 0.01UF K
CX40624015104 CERAMIC CHIP CK73B 6.3V 100,000PF K
CX40724014104 CERAMIC CHIP, 16V F 0.1UF Z
CX40824014104 CERAMIC CHIP, 16V F 0.1UF Z
CX40924014104 CERAMIC CHIP, 16V F 0.1UF Z
CX41024014104 CERAMIC CHIP, 16V F 0.1UF Z
CX41124014104 CERAMIC CHIP, 16V F 0.1UF Z
CX41524619040 ELEC. CHIP, 16V 10UF M 3A
CX41624619040 ELEC. CHIP, 16V 10UF M 3A
CX41724014104 CERAMIC CHIP, 16V F 0.1UF Z
CX43024013330 CERAMIC CHIP, 50V CH 33PF J
CX43524013330 CERAMIC CHIP, 50V CH 33PF J
CX43624013330 CERAMIC CHIP, 50V CH 33PF J
CX43724013330 CERAMIC CHIP, 50V CH 33PF J
CX43824015102 CERAMIC CHIP, 50V B 1000PF K
CX43924619157 MENJISSOU TYP 16V100U
CX47124014104 CERAMIC CHIP, 16V F 0.1UF Z
CX50024105220 CERAMIC CHIP, 50V CH 22PF J
CX50124014104 CERAMIC CHIP, 16V F 0.1UF Z
CX50224619042 ELEC. CHIP, 16V 22UF M 3A
CX50424015105 CHIP CERA CAP B 6.3V 105K
CX50524015105 CHIP CERA CAP B 6.3V 105K
CX50624015105 CHIP CERA CAP B 6.3V 105K
CX50724015105 CHIP CERA CAP B 6.3V 105K
CX50824015105 CHIP CERA CAP B 6.3V 105K
CX50924015105 CHIP CERA CAP B 6.3V 105K
CX51424619147 6.3V 47U UWXOJ470MCR1GB
CX51624015105 CHIP CERA CAP B 6.3V 105K
CX51724015105 CHIP CERA CAP B 6.3V 105K
CX51824015105 CHIP CERA CAP B 6.3V 105K
CX51924015105 CHIP CERA CAP B 6.3V 105K
CX52424015105 CHIP CERA CAP B 6.3V 105K
CX52524015105 CHIP CERA CAP B 6.3V 105K
CX52624015105 CHIP CERA CAP B 6.3V 105K
CX52724015105 CHIP CERA CAP B 6.3V 105K
CX52824015105 CHIP CERA CAP B 6.3V 105K
CX53024015105 CHIP CERA CAP B 6.3V 105K
CX53124014104 CERAMIC CHIP, 16V F 0.1UF Z
CX53224015105 CHIP CERA CAP B 6.3V 105K
CX53324013220 CERAMIC CHIP, 50V CH 22PF J
CX53524088133 OSCON 6.3V 47UF 6SVP47M
CX53724015105 CHIP CERA CAP B 6.3V 105K
CX53824015105 CHIP CERA CAP B 6.3V 105K
CX53924015105 CHIP CERA CAP B 6.3V 105K
CX55224013470 CERAMIC CHIP, 50V CH 470PF J
CX55324013100 CERAMIC CHIP CC73CH 50V 10PF D
CX55424013470 CERAMIC CHIP, 50V CH 470PF J
CX55524014104 CERAMIC CHIP, 16V F 0.1UF Z
CX55624619042 ELEC. CHIP, 16V 22UF M 3A
CX56224013101 CERAMIC CHIP, 50V CH 100PF J
CX56424013270 CERAMIC CHIP, 50V CH 27PF J
CX56524014104 CERAMIC CHIP, 16V F 0.1UF Z
CX57224013101 CERAMIC CHIP, 50V CH 100PF J
CX57424013270 CERAMIC CHIP, 50V CH 27PF J
CX57524014104 CERAMIC CHIP, 16V F 0.1UF Z
CX57624014104 CERAMIC CHIP, 16V F 0.1UF Z
CX57724014104 CERAMIC CHIP, 16V F 0.1UF Z
CX57824015105 CHIP CERA CAP B 6.3V 105K
CX60024619042 ELEC. CHIP, 16V 22UF M 3A
CX60224015105 CHIP CERA CAP B 6.3V 105K
CX60324015105 CHIP CERA CAP B 6.3V 105K
CX60424015105 CHIP CERA CAP B 6.3V 105K
CX60524015105 CHIP CERA CAP B 6.3V 105K
CX60624015105 CHIP CERA CAP B 6.3V 105K
CX60724015105 CHIP CERA CAP B 6.3V 105K
CX60824015105 CHIP CERA CAP B 6.3V 105K
CX60924015105 CHIP CERA CAP B 6.3V 105K
CX61024015105 CHIP CERA CAP B 6.3V 105K
CX61124015105 CHIP CERA CAP B 6.3V 105K
CX61224015105 CHIP CERA CAP B 6.3V 105K
CX61324015105 CHIP CERA CAP B 6.3V 105K
CX61424013470 CERAMIC CHIP, 50V CH 470PF J
CX62124015105 CHIP CERA CAP B 6.3V 105K
CX62224015105 CHIP CERA CAP B 6.3V 105K
CX62324015105 CHIP CERA CAP B 6.3V 105K
CX62424015105 CHIP CERA CAP B 6.3V 105K
CX62524619147 6.3V 47U UWXOJ470MCR1GB
CX63124015105 CHIP CERA CAP B 6.3V 105K
CX63224015105 CHIP CERA CAP B 6.3V 105K
CX63324015105 CHIP CERA CAP B 6.3V 105K
CX63424015105 CHIP CERA CAP B 6.3V 105K
CX63524619147 6.3V 47U UWXOJ470MCR1GB
CX63624014104 CERAMIC CHIP, 16V F 0.1UF Z
CX63724014104 CERAMIC CHIP, 16V F 0.1UF Z
CX63824014104 CERAMIC CHIP, 16V F 0.1UF Z
CX80324619042 ELEC. CHIP, 16V 22UF M 3A
CX80424014104 CERAMIC CHIP, 16V F 0.1UF Z
CX80524619147 6.3V 47U UWXOJ470MCR1GB
CX80624014104 CERAMIC CHIP, 16V F 0.1UF Z
CX80724619147 6.3V 47U UWXOJ470MCR1GB
CX80824014104 CERAMIC CHIP, 16V F 0.1UF Z
CX83424013330 CERAMIC CHIP, 50V CH 33PF J
CX83524013330 CERAMIC CHIP, 50V CH 33PF J
CX83724013330 CERAMIC CHIP, 50V CH 33PF J
CX84524013330 CERAMIC CHIP, 50V CH 33PF J
CX84624013330 CERAMIC CHIP, 50V CH 33PF J
CX90124092747 CERAMIC CHIP, 50V B 4.7UF K
CX90224014104 CERAMIC CHIP, 16V F 0.1UF Z
CX90324014104 CERAMIC CHIP, 16V F 0.1UF Z
CX90424619147 6.3V 47U UWXOJ470MCR1GB
CX90924092747 CERAMIC CHIP, 50V B 4.7UF K
CX91024014104 CERAMIC CHIP, 16V F 0.1UF Z
CX91124014104 CERAMIC CHIP, 16V F 0.1UF Z
CX91224619147 6.3V 47U UWXOJ470MCR1GB
CX91424092795 CERAMIC CHIP CK73B 6.3V 2.2UP K
CX91524092795 CERAMIC CHIP CK73B 6.3V 2.2UP K
CX91624092795 CERAMIC CHIP CK73B 6.3V 2.2UP K
CX91724092747 CERAMIC CHIP, 50V B 4.7UF K
CX91824014104 CERAMIC CHIP, 16V F 0.1UF Z
CX91924014104 CERAMIC CHIP, 16V F 0.1UF Z
CX92024619147 6.3V 47U UWXOJ470MCR1GB
CX92124092794 CERAMIC CHIP CK732B 6.3V 10UF M
CX92224092794 CERAMIC CHIP CK732B 6.3V 10UF M
CX92324092794 CERAMIC CHIP CK732B 6.3V 10UF M
CX92424092794 CERAMIC CHIP CK732B 6.3V 10UF M
CX92524092794 CERAMIC CHIP CK732B 6.3V 10UF M
CX92624092907 CERA CHIP CK733B 6.3V 22UF K
CX92724100104 CERAMIC CHIP, 25V F 0.1UF Z
CX92824619147 6.3V 47U UWXOJ470MCR1GB
CX92924092795 CERAMIC CHIP CK73B 6.3V 2.2UP K
CX93024092795 CERAMIC CHIP CK73B 6.3V 2.2UP K
CX93124092795 CERAMIC CHIP CK73B 6.3V 2.2UP K
CX93324092795 CERAMIC CHIP CK73B 6.3V 2.2UP K
CX93424092795 CERAMIC CHIP CK73B 6.3V 2.2UP K
CX93524092795 CERAMIC CHIP CK73B 6.3V 2.2UP K
CX93624092795 CERAMIC CHIP CK73B 6.3V 2.2UP K
CX93724092795 CERAMIC CHIP CK73B 6.3V 2.2UP K
CX93824092539 CERAMIC CHIP, 10V F 2.2UF Z
CX93924092795 CERAMIC CHIP CK73B 6.3V 2.2UP K
CX94324092795 CERAMIC CHIP CK73B 6.3V 2.2UP K
CX94424092539 CERAMIC CHIP, 10V F 2.2UF Z
SPECIFIC INFORMATIONS
-
27
-
Location
No.
Parts No. Description
Location
No.
Parts No. Description
SPECIFIC INFORMATIONS
CX94524092795 CERAMIC CHIP CK73B 6.3V 2.2UP K
CX94624092795 CERAMIC CHIP CK73B 6.3V 2.2UP K
CX94724092795 CERAMIC CHIP CK73B 6.3V 2.2UP K
CX94824092795 CERAMIC CHIP CK73B 6.3V 2.2UP K
CX94924092795 CERAMIC CHIP CK73B 6.3V 2.2UP K
CX95024092795 CERAMIC CHIP CK73B 6.3V 2.2UP K
CX95124092747 CERAMIC CHIP, 50V B 4.7UF K
CX95224092794 CERAMIC CHIP CK732B 6.3V 10UF M
CX95324092795 CERAMIC CHIP CK73B 6.3V 2.2UP K
CX95424092795 CERAMIC CHIP CK73B 6.3V 2.2UP K
CY00124014104 CERAMIC CHIP, 16V F 0.1UF Z
CY00224014104 CERAMIC CHIP, 16V F 0.1UF Z
CY00424092785 CERAMIC CHIP, 10V B 0.47UF K
CY00524014104 CERAMIC CHIP, 16V F 0.1UF Z
CY00624015103 CERAMIC CHIP, 16V B 0.01UF K
CY00724015103 CERAMIC CHIP, 16V B 0.01UF K
CY00824013180 CERAMIC CHIP, 50V CH 18PF J
CY00924015102 CERAMIC CHIP, 50V B 1000PF K
CY01024013050 CERAMIC CHIP CC73CH 50V 5PF C
CY01124014104 CERAMIC CHIP, 16V F 0.1UF Z
CY01224014104 CERAMIC CHIP, 16V F 0.1UF Z
CY01324014104 CERAMIC CHIP, 16V F 0.1UF Z
CY01524092738 CERAMIC CHIP, 25V B 0.47UF K
CY01624014104 CERAMIC CHIP, 16V F 0.1UF Z
CY01724014104 CERAMIC CHIP, 16V F 0.1UF Z
CY01824014104 CERAMIC CHIP, 16V F 0.1UF Z
CY02024015103 CERAMIC CHIP, 16V B 0.01UF K
CY02124092573 CERAMIC CHIP, 16V B 0.47UF K
CY02224013330 CERAMIC CHIP, 50V CH 33PF J
CY02324013330 CERAMIC CHIP, 50V CH 33PF J
CY02424092573 CERAMIC CHIP, 16V B 0.47UF K
CY02524014104 CERAMIC CHIP, 16V F 0.1UF Z
CY02624014104 CERAMIC CHIP, 16V F 0.1UF Z
CY02724013040 CERAMIC CHIP CC73CH 50V 4PF C
CY02824014104 CERAMIC CHIP, 16V F 0.1UF Z
CY10224793101 ELECTROLYTIC, 10V 100UF M
CY10324109103 CERAMIC CHIP, 50V B 0.01UF K
CY10524109102 CERAMIC CHIP, 50V B 1000PF K
CY40124015104 CERAMIC CHIP CK73B 6.3V 100,000PF K
CY40324013680 CERAMIC CHIP, 50V CH 68PF J
CY40424013151 CERAMIC CHIP, 50V CH 150PF J
CY40524013680 CERAMIC CHIP, 50V CH 68PF J
CY40624013150 CHIP CH 50V 15PF J CC73CH1H150J
CY40724013680 CERAMIC CHIP, 50V CH 68PF J
CY40924013680 CERAMIC CHIP, 50V CH 68PF J
CY41024013151 CERAMIC CHIP, 50V CH 150PF J
CY41124013150 CHIP CH 50V 15PF J CC73CH1H150J
CY41224013680 CERAMIC CHIP, 50V CH 68PF J
CY41324013150 CHIP CH 50V 15PF J CC73CH1H150J
CY41424015104 CERAMIC CHIP CK73B 6.3V 100,000PF K
CY41624013151 CERAMIC CHIP, 50V CH 150PF J
CY41724015104 CERAMIC CHIP CK73B 6.3V 100,000PF K
CY41824013680 CERAMIC CHIP, 50V CH 68PF J
CY44024015103 CERAMIC CHIP, 16V B 0.01UF K
CZ0124013101 CERAMIC CHIP, 50V CH 100PF J
CZ0224013150 CHIP CH 50V 15PF J CC73CH1H150J
CZ0924619175 CHIP10V100UF 1A101P
CZ1024100104 CERAMIC CHIP, 25V F 0.1UF Z
CZ2124092907 CERA CHIP CK733B 6.3V 22UF K
CZ2224092794 CERAMIC CHIP CK732B 6.3V 10UF M
CZ2324092794 CERAMIC CHIP CK732B 6.3V 10UF M
CZ2424619175 CHIP10V100UF 1A101P
CZ2524619175 CHIP10V100UF 1A101P
CZ2724015104 CERAMIC CHIP CK73B 6.3V 100,000PF K
CZ2824013680 CERAMIC CHIP, 50V CH 68PF J
CZ2924013680 CERAMIC CHIP, 50V CH 68PF J
CZ3024013151 CERAMIC CHIP, 50V CH 150PF J
CZ3124092859 CERAMIC CHIP CK73B 10V 1UF K
CZ3224015102 CERAMIC CHIP, 50V B 1000PF K
CZ3424013270 CERAMIC CHIP, 50V CH 27PF J
CZ3624015104 CERAMIC CHIP CK73B 6.3V 100,000PF K
CZ3824015104 CERAMIC CHIP CK73B 6.3V 100,000PF K
CZ3924013101 CERAMIC CHIP, 50V CH 100PF J
CZ4024013390 CERAMIC CHIP CC73CH 50V 39PF J
CZ4224100104 CERAMIC CHIP, 25V F 0.1UF Z
CZ4324100104 CERAMIC CHIP, 25V F 0.1UF Z
CZ4424100104 CERAMIC CHIP, 25V F 0.1UF Z
CZ4524105330 CERAMIC CHIP, 50V CH 33PF J
CZ4624100104 CERAMIC CHIP, 25V F 0.1UF Z
CZ4724100104 CERAMIC CHIP, 25V F 0.1UF Z
CZ4824100104 CERAMIC CHIP, 25V F 0.1UF Z
CZ4924100104 CERAMIC CHIP, 25V F 0.1UF Z
CZ5124100104 CERAMIC CHIP, 25V F 0.1UF Z
CZ5224100104 CERAMIC CHIP, 25V F 0.1UF Z
CZ5324100104 CERAMIC CHIP, 25V F 0.1UF Z
CZ5424100104 CERAMIC CHIP, 25V F 0.1UF Z
CZ5524100104 CERAMIC CHIP, 25V F 0.1UF Z
CZ5824013120 CERAMIC CHIP CC731CH 50V 12PF J
CZ5924105120 CERAMIC CHIP, 50V CH 12PF J
CZ6024100104 CERAMIC CHIP, 25V F 0.1UF Z
CZ6224100104 CERAMIC CHIP, 25V F 0.1UF Z
CZ6324105821 CERAMIC CHIP, 25V CH 820PF J
CZ6424105561 CERAMIC CHIP, 50V CH 560PF J