TJERNLUND IN-LINE DRAFT INDUCER REFERENCE GUIDE 8500590 REV. B 0403, DJ-3, D-3, I, IL Reference Manual
...
Improve Heating Efficiency
In-Line Draft Inducers assure positive draft
when restricted boilers and furnaces, poor
chimneys or negative pressures in buildings prevent proper exhaust of combustion gases. The Venturi action starts air
moving up the stack instantly and keeps it
moving smoothly. In-Line inducers are
built for long-lasting, trouble-free service
and available in sizes and capacities to
meet virtually all heating system requirements. The Vari-Draft control permits
adjustment to individual job requirements. Vents/Chimneys utilizing In-Line
Draft Inducers must be vertically terminated above the roof line.
www.tjernlund.com •
800.255.4208
Residential Commercial Industrial
Reference Guide
by
Tjernlund
In-Line
Draft
Inducers
Use On Vertically Terminated Vent Systems Only
Typical Applications:
• Boilers/Furnaces
• Water Heaters
• Modular Boiler Systems
• Multiple Appliances
• Bakery Ovens
• Factory Processes
Solves Venting Problems:
• Undersized Chimneys
• Negative Pressures
• Long Horizontal Vent Connectors
• Down Drafts
• Cold Equipment Starts
• Restrictive Heat Exchangers/Combustion
Chambers
Everything Needed to Conform
Easy Installation
www.tjernlund.com •
800.255.4208
A Size For Every Application
Models
DJ-3, D-3
Models
I, IL, XL
Model
HD
1. Cut Slot in Pipe
2. Insert Inducer
3. Install Bands*
■ Select a position between draft
hood, diverter or barometric
damper and chimney, locating
the Inducer as close to the
chimney as possible. Inducer
should be mounted 2-3 pipe
diameters away from a directional
change, i.e. elbows and tees, so turbulence is not created.
■ Mount the Draft Inducer on vertical, horizontal or inclined vent
pipe. If used on a horizontal vent pipe, mount Inducer on bottom
of pipe, not on top, to avoid creating a heat trap in the Inducer.
■The motor shaft must be level and horizontal to avoid excessive
wear on bearing.
Three Basic
Steps...
Typical In-Line
Inducer and safety
interlock using
UC1 Control and
PS1505 Fan Prover
Tjernlund offers
six In-Line Draft
Inducers to fit
vent pipe sizes
from 3" to 24".
UC1 Control
PS1505
Fan Prover
* Models DJ-3 & D-3 fasten with screws.
■ If change in vent pipe size is required, use a tapered
increaser or reducer.
■ In-Line Inducers should be installed on a section of single
wall vent pipe in order to assure proper performance.
■ Do not use In-Line Draft Inducers on condensing heating
equipment.
■ We recommend the use of a carbon monoxide detector
in all mechanical rooms.
Fan Prover Safety Interlock
Model PS1505
To satisfy national mechanical codes for oil and gas installations,
Draft Inducers must be properly interlocked with burner circuits.
The PS1505 Fan Proving Switch monitors pressure within the
Inducer housing to verify Inducer operation. Used in conjunction
with the UC1 Universal Control, it assures compliance with codes
and simplifies electrical interlock with all 24 /115 VAC burner
circuits. The PS1505 is not compatible with millivolt gas valves.
with National Mechanical Codes
Chimney
Quality engineered and
manufactured to maintain a
consistent draft on a wide
range of oil and gas fired
heating equipment. May be
used with chimney vented or
power vented heating equipment. For fan assisted gas, oil
or solid fuel applications with
vent diameters from 4"–10",
choose the DC4 thru DC10.
For LP and natural gas applications with vent diameters from 4"–10", choose the DC4G
thru DC10G.
Used with any UC1 controlled Inducer to interlock additional 24/115
VAC heaters. Powered by
and communicates with
the UC1 through a factory
wired whip. For one
additional 24/115 VAC
heater add the MAC1E.
To interlock up to four
more additional 24/115
VAC heaters, add the
MAC4E. MAC4Es can be
daisy chained together for greater than 5 heaters.
Important:
Total combined BTU/hr. input of all heaters and total equivalent
pipe lengths must be within Inducer’s capacity.
For use with UC1 Universal
Control, MAC1E or MAC4E
auxiliary controls. The WHKE
gas pressure switch actuates
the Inducer through the A - B
dry contacts. The Linear Limit
switch disables the heater in
the event of a venting
malfunction. Includes JA1
thermocouple junction
adapter. To interlock millivolt
water heater(s) only with a
UC1 controlled Inducer add a
WHKE for each millivolt heater. To interlock a millivolt water
heater and one 24/115 VAC furnace or boiler with a UC1
controlled Inducer, add a WHKE and a MAC1E.
Solid state control interlocks
with virtually any burner control
circuit. Features include:
adjustable pre and post purge,
LED status/diagnostic indicators,
prover switch delay to avoid
burner start up and wind
induced short cycling. Interlocks
with any 24/115 VAC burner
control circuit and also includes
“dry” contact actuation option.
Selectable voltage eliminates
false activation by burner control
check circuits.
Universal Control
Model UC1
Millivolt Safety Interlock Kit
Model WHKE
Barometric Draft Controls
Models DC4, DC5, DC6, DC7, DC8, DC9, DC10
DC4G, DC6G, DC7G, DC8G, DC9G, DC10G
Multiple Appliance Controls
Models MAC1E, MAC4E
www.tjernlund.com •
800.255.4208
For additional information request brochure #8500004
For additional information request brochure #8500490
Accessories
The UC1 is a standardized control for Tjernlund Inducers/Venters.
It offers many installation, operational and safety benefits.
Model Dimensions
Model
DJ-3
D-3
I
IL
XL
HD
H
7 1/2
9 1/8
14 1/2
17
18 7/8
27 1/2
W
8 1/2
9 1/2
13 1/2
14 3/4
18 1/2
16 3/4
D
5 7/8
7
8 3/4
10
10 1/2
25
X
2 5/8
3 1/8
4
4 1/8
5 1/8
6
Unit
Dimensions (In.)
Slot
Y
7 5/8
8 5/8
12 3/4
15
16 3/4
24 1/2
Ship
Weight
8 Lbs
10 Lbs
31 Lbs
34 Lbs
53 Lbs
176 Lbs
“H” — Overall Height
“D” — Overall Depth
“W”— Overall Width
“X” — Pipe Slot Width
“Y” — Pipe Slot Height
TJERNLUND PRODUCTS, INC.
1601 Ninth Street White Bear Lake, MN 55110-6794
Phone: 651.426.2993 800.255.4208 Fax: 651.426.9547
Visit our web site: www.tjernlund.com
Copyright © 2003 Tjernlund Products, Inc. P/N 8500590 Rev B 4/03
1. Inputs shown are
believed to be maximum
capacities for inducers
when mounted on pipe
sizes shown for ordinary
jobs where a moderate
amount of mechanical
induced draft is required.
2. Consideration is given
to typically higher static
pressure requirements for
larger installations, for the
type of fuel burned and
for the type of draft
control installed.
3. Some ratings may only
be valid for extremely
short vent lengths due to
excessive pressure loss; i.e.
the Model IL gas firing
with draft hood in 10"
pipe at 2,080,000 BTU/hr.
4. Where pressure requirements are unknown or
believed to be unusually
severe, ask for complete
performance curves or
consult factory.
5.
Draft Inducers should
be installed in single wall
vent pipe in order to assure
proper performance.
Model Selection Table and Electrical Data
Model
DJ-3
D-3
I
IL
XL
HD
Pipe
Size
In.
3
4
5
6
5
6
7
8
8
9
10
12
9
10
12
14
16
18
16
18
20
24
20
24
69,000
105,000
111,000
100,000
270,000
356,000
360,000
320,000
900,000
1,110,000
1,250,000
1,030,000
1,460,000
2,080,000
1,920,000
1,840,000
900,000
650,000
4,000,000
3,900,000
2,800,000
1,500,000
5,300,000
3,500,000
Gas Firing
with Draft
Hood
270
0
F
Flue Gas
S.P.
.034
.042
.043
.041
.063
.073
.075
.068
.125
.135
.140
.128
.145
.170
.160
.159
.120
.099
.250
.240
.195
.150
.290
.220
CFM
48
72
72
68
190
246
259
217
590
765
850
710
1010
1370
1325
1270
620
450
2760
2650
1935
1035
3690
2415
72,000
109,000
104,000
34,000
330,000
377,000
330,000
222,000
1,200,000
1,330,000
1,260,000
710,000
1,970,000
2,460,000
2,230,000
1,470,000
650,000
440,000
4,000,000
3,250,000
2,100,000
1,100,000
5,200,000
3,750,000
Gas Firing
with Barometric
Draft Control
390
0
F
Flue Gas
S.P.
.047
.053
.052
.042
.085
.090
.085
.075
.143
.150
.145
.115
.175
.185
.182
.158
.113
.095
.260
.240
.175
.125
.270
.220
CFM
36
55
52
17
166
190
166
110
603
653
615
357
989
1240
1120
740
340
220
2010
1660
1079
527
2440
1660
58,000
92,000
74,000
25,000
295,000
300,000
230,000
123,000
1,100,000
1,100,000
840,000
400,000
1,700,000
1,900,000
1,500,000
825,000
350,000
200,000
3,300,000
2,100,000
1,200,000
503,000
3,600,000
2,900,000
Oil Firing
with Barometric
Draft Control
530
0
F
Flue Gas
S.P.
.048
.057
.052
.035
.092
.093
.080
.065
.147
.148
.136
.100
.180
.180
.170
.135
.095
.075
.230
.190
.150
.110
.240
.218
CFM
33
48
39
13
163
169
118
65
566
566
440
211
900
1010
789
453
184
106
1763
1103
626
266
1870
1550
Therm
Volts HZ RPM Watts Amps Prot.
115 60 1550 35 .43 Imp.
Prot.
115 60 1550 74 .96 Yes
115 60 1725 1/4 HP 5.4 Yes
115 60 1725 1/4 HP 5.4 Yes
115 60 1725 1/3 HP 6.0 Yes
115 12.6
208 60 1725 1 HP 6.2 Yes
230 6.3
208 6.3
230 60 1725 2 HP 6.4 No
460 3.2
Heater
BTU
Input
Heater
BTU
Input
Heater
BTU
Input
Electrical Specifications
IMPORTANT: Vents/Chimneys utilizing In-Line Draft Inducers must be vertically terminated above the roof line.
Do not use for side wall venting. Consult factory for proper side wall vent system options.
Tjernlund Products also offers:
Auto-Draft variable & fixed speed Inducers for roof top or side wall
venting. Reduce vent diameters by up to 50% and overcome convoluted vent layouts. Fan speed is automatically regulated based on a user
set manifold/vent pressure, resulting in perfect draft and true energy
savings. Virtually unlimited capacities.
Combustion Air In-Forcers provide dedicated combustion air for safer,
more efficient equipment operation. Eliminates burner control lockouts
& oil odors associated with backdrafting. Ideal for "confined space" and
electric to oil or gas conversions. Residential and commercial fixed &
variable speed capacities up to 6000 CFM available.
Auto-Draft®Inducer
Combustion Air
In-Forcer
™
Note: Tjernlund
Products Inc. reserves
the right to make
changes to specifications without notice.
Distributed by:
Loading...