Thetford S~OH70000Z, S~OH71000Z User And Installation Instructions Manual

PCC 1265Z

–

Issue 7

FOR USE IN AUSTRALIA

USER AND INSTALLATION INSTRUCTIONS

PLEASE READ THOROUGHLY AND KEEP FOR FUTURE

MODELS

S~OH70000Z - TRIPLEX

S~OH71000Z – TRIPLEX DUAL FUEL

THETFORD AUSTRALIA PTY LTD

41 LARA WAY CAMPBELLFIELD VIC

TEL: [phone] FAX: [phone]

BUILD IN APPLIANCES

FOR USE WITH PROPANE GAS

2

3

SPECIFICATION

Note 1:- Available with alternative 1000W Electric Hotplate

GAS: PROPANE only @ 2.75kpa

TRIPLEX TRIPLEX TRIPLEX TRIPLEX TRIPLEX
Model Range S~OH70000Z S~OH70000Z S~OH70000Z S~OH70000Z S~OH71000Z
External Dimensions, mm

(HxWxD)

468 x 456 x 500mm 468 x 456 x 500mm 468 x 456 x 500mm 468 x 456 x 500mm 468 x 456 x 500mm

Oven Capacity, litres

36 36 36 36 36

No. of tray positions

Grill 2, Oven 4 Grill 2, Oven 4 Grill 2, Oven 4 Grill 2, Oven 4 Grill 2, Oven 4

Heat input

Total heat input 29.4MJ/h 27.1MJ/h 25.5MJ/h 32.3MJ/h 23.3MJ/h

800W Elec (Note 1)

Hotplate Burners (LPG) 3 x 6.1MJ/h

2 x 6.1MJ/h

AUX 1 x 3.8MJ/h

2 x 5.3MJ/h

AUX 1 x 3.8MJ/h

2 x 6.1MJ/h
1 x 9.0MJ/h

2 x 6.1MJ/h

Electric Hotplate
(220V - 240V ~ 50Hz)

N/A N/A N/A N/A 1 x 1000W Max

Grill burner heat input 5.3MJ/h 5.3MJ/h 5.3MJ/h 5.3MJ/h 5.3MJ/h
Oven burner heat input 5.8MJ/h 5.8MJ/h 5.8MJ/h 5.8MJ/h 5.8MJ/h

Injector size, mm

Hotplate Burners Sabaf 0.67 Sabaf 2x0.67, 1x0.53 Sabaf 2x0.62, 1x0.53 Sabaf 2x0.67, 1x0.81 Sabaf 2x0.67
Grill burner Sabaf 0.62 Sabaf 0.62 Sabaf 0.62 Sabaf 0.62 Sabaf 0.62
Oven burner Sabaf 0.65 Sabaf 0.65 Sabaf 0.65 Sabaf 0.65 Sabaf 0.65

Bypass size, mm

Hotplate Controls Sabaf 0.34 Sabaf 0.34 Sabaf 0.34 Sabaf 0.34 Sabaf 0.34
Grill control N/A N/A N/A N/A N/A
Oven control Sabaf 0.35 Sabaf 0.35 Sabaf 0.35 Sabaf 0.35 Sabaf 0.35

Spark ignition (where fitted) 12V 12V 12V 12V 12V
Weight (Kg)

21.5Kg 21.5Kg 21.5Kg 21.5Kg 23.1Kg

IMPORTANT

• THIS APPLIANCE IS SUITABLE FOR USE WITH PROPANE AND

SHOULD NOT BE USED ON ANY OTHER GAS.

• USE ONLY THE GAS PRESSURES SPECIFIED ABOVE

• THIS APPLIANCE MUST BE EARTHED.

INTRODUCTION

In your own interest of safety, gas appliances should be installed by competent persons.
Failure to install the appliance correctly could invalidate any warranty or liability claims. This
appliance shall be installed in accordance with the manufacturers installation instructions, local
gas fitting regulations, municipal building codes, AG5601 and any other relevant statutory
regulations.

Data label.
The data label is located on the right hand side front of the oven compartment, behind the oven
door. A duplicate data label is supplied to adhere to an accessible area next to the appliance.
Ensure that the gas supply is Propane. This appliance is designed for use with Propane gas
and should not be converted for use with any other gas.

Provision of Ventilation

The use of a gas cooking appliance results in a production of heat and moisture in a room in
which it is installed. Ensure that the kitchen is well ventilated and in accordance with AG5601
Installation Code. In general, the appliance should have adequate ventilation for complete
combustion of gas, proper flueing and to maintain temperature of immediate surroundings
within safe limits.

Location

This appliance maybe installed in a kitchen/kitchen diner but NOT in a room containing a bath
or a shower. LP gas appliances must not be fitted below ground level. e.g. in a basement.

Choose a location free of draughts, open doors and clear of combustible materials and other
fire hazards. The location should ensure convenience of operation and service. Any adjoining
wall surface situated within 200mm from the edge of any hob burner must be made from a
suitable non-combustible material for a height of 150mm for the entire length of the hotplate.

IMPORTANT

• This appliance must be installed into an aperture, sealed off at either side in order to
prevent draughts from adjoining cupboards/vents. Ensure that air vents and gas
escape holes are kept clear, holes for cables and pipes must be sized to minimize air
leakage between compartments.

• Under no circumstances should the ventilation hole exceed 3850mm

2

or other low
level ventilation be located in the compartment, including vents in kickboards. Low
level vents in adjacent compartments are permitted.