Thermador VTN630W Installation Manual
THERMADOR.COM
Ventilation Blower Motor
VTN630W and VTN1090W
Installation
INSTRUCTIONS
Page. 1
This THERMADOR® appliance is made by
BSH Home Appliances Corporation
1901 Main Street, Suite 600
Irvine, CA 92614
Questions?
1-800-735-4328
www.thermador.com
We look forward to hearing from you!
Table of
CONTENTS
Safety ..................................................................................2
Installation ...........................................................................4
Support, Accessories & Parts................................back page
Safety
DEFINITIONS
WARNING
This indicates that death or serious injuries may occur as a
result of non-observance of this warning.
CAUTION
This indicates that minor or moderate injuries may occur as a
result of non-observance of this warning.
NOTICE: This indicates that damage to the appliance or
property may occur as a result of non-compliance with this
advisory.
Note: This alerts you to important information and/or tips.
Page. 2
Safety
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
INSTALLER: Save these instructions for the local electrical
inspector’s use. Please leave these instructions with this
unit for the owner. Show the owner the location of the
circuit breaker or fuse. Mark it for easy reference.
OWNER: Please retain these instructions for future
reference.
Check if this blower is recommended by the manufacturer
to be installed with the hood.
WARNING
If the information in this manual is not followed
exactly, fire or shock may result causing property
damage or personal injury.
WARNING
To avoid electrical shock hazard, before installing,
switch power off at the service panel and lock the
panel to prevent the power from being switched on
accidentally.
CAUTION
FOR GENERAL VENTILATING USE ONLY. DO NOT
use to exhaust hazardous or explosive materials and
vapors.
WARNING
To reduce the risk of fire or electric
shock, do not use
this blower with any solid-state
speed control device.
WARNING
This appliance must be grounded. Improper
grounding can result in a risk of electric shock. Consult
a qualified electrician if the grounding instructions are
not completely understood, or if doubt as to whether
the appliance is properly grounded.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,
OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:
• Installation work and electrical wiring must be
done by qualified person(s) in accordance with all
applicable codes and standards, including firerated construction.
• Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of
fuel burning equipment to prevent back drafting.
Follow the heating equipment manufacturer's
guideline and safety standards such as those
published by the National Fire Protection
Association (NFPA), and the American Society for
Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE), and the local code
authorities.
• USE ONLY METAL DUCTWORK.
• To reduce risk of fire and to properly exhaust air,
be sure to duct air outside. DO NOT vent exhaust
air in spaces with walls or ceilings or into attics,
crawl spaces or garages.
• When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden
utilities.
State of California Proposition 65 Warning:
WARNING
This product can expose you to chemicals including
vinyl chloride, which is known to the State of California
to cause cancer and birth defects or other
reproductive harm. For more information go to
www.P65Warnings.ca.gov.
Page. 3
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
WARNING
DO NOT repair or replace any part of the appliance
unless specifically recommended in the manuals.
Improper installation, service or maintenance can
cause injury or property damage. Refer to the
Installation Manual for guidance. All servicing should
be done by a qualified technician.
If required by the National Electrical Code (or Canadian
Electrical Code), this appliance must be installed on a
separate branch circuit.
WARNING
ELECTRICAL SHOCK HAZARD:
• DO NOT remove connections.
• DO NOT use an extension cord.
Remove all tape and packaging before using the
appliance. Destroy or recycle the packaging after
unpacking the appliance.
Never allow children to play with packaging material.
Page. 4
Installation
Exhaust-air Mode
Exhaust air should not be directed into a smoke or exhaust
flue that is currently used for other purposes, nor into a
shaft that is used for ventilating rooms in which stoves or
fireplaces are also located.
Exhaust air must be discharged in accordance with official
and statutory regulations only (e.g. national building
regulations).
Local regulations must be observed when discharging air
into smoke or exhaust flues that are not otherwise in use.
When the extractor hood is operated in exhaust-air mode
simultaneously with a different burner which also makes
use of the same chimney (such as gas, oil or coal-fired
heaters, continuous-flow heaters, hot-water boilers), care
must be taken to ensure that there is an adequate supply
of fresh air, which will be needed by the burner for
combustion.
Safe operation is possible provided that the underpressure in the room where the burner is installed does
not exceed 4 Pa (0.04 mbar).
This can be achieved if combustion air can flow through
non-lockable openings, e.g. in doors, windows and via the
air-intake/exhaust-air wall box or by other technical
measures, such as reciprocal interlocking, etc.
If the air intake is inadequate, there is a risk of carbon
monoxide poisoning from combustion gases which are
drawn back into the room.
An air-intake/exhaust-air wall box by itself is no guarantee
that the limiting value will not be exceeded.
NOTE: When assessing the overall requirement, the
combined ventilation system for the entire household
must be taken into consideration. This rule does not apply
to the use of cooking appliances, such as ranges and
ovens.
IMPORTANT SAFETY INSTRUCTIONS
• The blower must be attached at least 78¾'' (200 cm)
from the extractor hood.
• When attaching the outer wall blower, ensure that it is
accessible for maintenance and repairs.
• The plug-and-socket connections of the electric
cables must be located inside the building, according
to local codes.
• DO NOT reduce the 6'' (152 mm) diameter of the
ducting connected to the extractor hood.
VTN630W and VTN1090W
Integral Blower Installation
Suitable for the following hood models:
HPCN36WS, HPCN48WS, PH30HWS, PH36HWS,
PH48HWS, PH36GWS, PH42GWS, PH48GWS,
PH54GWS, PH60GWS, VCIN36GWS, VCIN42GWS,
VCIN48GWS, VCIN54GWS, VCIN60GWS, HPIN42WS,
HPIN54WS
Integral Blower models are integrated into the ventilation
hood at the time of installation.
Refer to the Installation Manual for important safety
instructions. Use gloves when installing blower unit.
1. The blower is attached to the hood using weld studs
provided on the mounting plate. Guide the motor
mounting plate over the studs.
2. Attach (4) nuts (included with hood) to the weld studs.
Tighten nuts to secure the blower to the hood.
3. Connect the blower’s plug connector to the connector
present inside the hood.
Loading...