Thermador T24UW810LS Installation Manual
Model/Modele/Modelo
T24UW820LS
T24UW810LS
T24UW820RS
T24UW810RS
T24UW800LP
T24UW800RP
Glass Door Wine Reserve
Cellier avec porte en verre
Enfriador de vinos
INSTALLATION
GUIDE
GUIDE
D'INSTALLATION
GUIA DE
INSTALACION
Page | 1
IMPORTANT:
INSTALLER:
OWNER:
Before you begin, read these instructions completely and
carefully.
Please leave this manual with owner for future reference.
Save these installation instructions for local electrical
inspector’s use and for future reference.
Table of Contents
Introduction ………………………………….
- Inspect the Wine Reserve
Tools needed for installation ……………..
Materials supplied …………….………….…
Installing the appliance …………………….
- Transporting
- General measures
- Installation location
- Installing Side-by-Side
Ventilation …………………………………….
Connecting the appliance …………………
- Electrical connection
Door opening …………………………………
Installing the anti-tip-brackets ……………..
Installing the overlay frame ………………..
Customer Service Information ……………
Addendum A …………………………………
3
4
4
5
1
1
1
2
2
Page | 2
Introduction
These installation instructions are intended for use by qualified installers.
In addition to these instructions, the appliance shall be installed:
x In the United States, in accordance with the
National Electric Code/State and municipal
codes and/or local codes.
x In Canada, in accordance with the Canadian
Electric Code C22.1 – latest edition/Provincial
and Municipal codes and/or local codes.
Please read these installation instructions completely and carefully.
They will save you time and effort and help to ensure optimum performance.
Be sure to observe all listed warnings and cautions.
Look for the triangles with exclamation marks inside.
WARNING:
This indicates that death or serious
injury may result due to non-observance
of this warning.
CAUTION:
This indicates that minor or moderately
severe injury may result due to nonobservance of this warning.
Important
x NEW INSTALLATION – If the appliance is a new installation, most of the work must be
done before the unit is moved into place.
x REPLACEMENT – If the appliance is replacing another appliance, the connections for
the appliance being replaced must be checked for compatibility with the new unit and
replaced as necessary.
Inspect the Wine Reserve
Remove all tape, packaging and plastic covers.
After unpacking the appliance and prior to installation, thoroughly inspect the Wine Reserve for possible
freight or cosmetic damage. Report any damage immediately.
NOTE: Please do not discard any bags or items that come with the original package until after the entire
installation has been completed!
Page | 3
Anti-tip-bracket. 2 pieces.
20 1/2”
(520mm) x 29 1/8” (740mm)
x 1/8” (3mm)
Screws for Overlay Panel: ST1TYA131SF
ONLY FOR T24UW800LP MODELS.
Tools needed for installation
Tape Measure Philips Screwdriver Level
These are the tools that you may need for the installation of the appliance. However, if you need to
modify the counter or cabinetry to fit the unit, you may need other tools to make counter/cabinetry
modifications before installing the appliance.
Materials supplied
Screws: 2 pieces.
Door Stopper Pin: 2
1 Insulating Foam
(Not illustrated)
(TRUSS M4X34 TAPPING). 8 pieces.
Page | 4
Installing the appliance
/
/
/
Most of the installation work must be done before the Wine Reserve is moved into place.
Have a technician install and connect the appliance according to the enclosed installation instructions.
WARNING:
Do not install this appliance:
- Outdoors
- In an environment with dripping water
- In rooms where there is a risk of frost
Transporting
The appliance is heavy and must be handled with caution during transportation and installation.
Because of the weight and dimensions of the appliance,
appliance into position securely and avoid injuries to people or damage to the appliance.
General measures
1
34
/4"
(870 mm)
301/8"
(765 mm)
at least two persons are necessary to move the
5
*26
/8"
(676 mm)
7
23
/8"
(607 mm)
1
21
(547 mm)
(610 mm)
/2"
24"
34
(870 mm)
1
4
8
"
(105 mm)
3
20
4
(527 mm)
"
Note: With the legs fully retracted the product has a minimum
dimension of 34
The legs can be extended up to
* Note:
Varies based on handle depth.
1
/4" from top to bottom.
1
/2".
7
23
/
8
"
(607 mm)
1
/
4
"
30
(765 mm)
1
"
/
2
(13 mm)
measurements in inches and mm
1
"
/
8
5
3
(92 mm)
8
"
All legs are adjustable by up to ½ inch.
Page | 5
Installation location
A dry, well ventilated room is suitable as an installation location. The installation location should not be
exposed to direct sunlight and not placed near a heat source, e.g. a cooker, radiator, etc.
If installation next to a heat source is unavoidable, use a suitable insulating plate or observe the following
minimum distance from the heat source:
To electric or gas oven/range 1¼” (3 cm).
To an oil or coal-fired cooker 11
To another Wine ReserveRU5HIULJHUDWRU 1” (2.54cm)
The floor of the installation location must not give way; if necessary, reinforce floor. The appliance must
be upright to function correctly.
For proper operation and appearance of the unit, the cabinet opening should be square and have
dimensions as shown in the next diagrams
TOP VIEW
13
/16” (30cm).
7
/
"
23
8
(607 mm)
unit
9
"
24"
(610 mm)
unit
min. 24
(min. 624 mm)
counter
/16
5
/
"
2
8
(66 mm)
1
(48 mm)
3
/16
24
7
/
"
8
"
(615 mm)
counter opening
FRONTAL VIEW
measurements in inches and mm
measurements in inches and mm
Page | 6
r
TOP VIEW OPEN 5,*+76:,1*
9
/
min. 24
16"
(min. 624 mm)
counte
3
/
24
16" (615 mm)
counter opening
26
110°
1
7239,(:23(1/()76:,1*
90°
1
/16"
(2 mm)
/
2" (675 mm)
24"
(610 mm)
unit
3
/
23
4"
(603 mm)
3
/
47
4 "
(1213 mm)
unit
5
/
2
8"
(66 mm)
Peasurements in inches DQGmm
Peasurements in inches DQGmm
Page | ϳ
Installing Side-by-Side
The appliance can be installed next to another Thermador appliance. Follow the next dimensions and
notes for the correct installation of the appliance in a side-by-side layout.
NOTE: Before placing the unit into the niche, adhere the Insulating Foam (included with the product) on
the side of the unit that will be placed next to the additional appliance. Be sure that the Insulating Foam is
even with the surface of the unit and that there are no bubbles or bumps on the Insulation Foam after
adhering it to the unit.
Side of the unit next to
the other appliance.
InsulaƟŶg Foam
Included with the unit.
Install the appliances in a “French Door” configuration; appliances with Left Hinge should be
opposite to another with Right Hinge.
7
/
23
8" (607 mm)
3
/
16" (1224 mm)
48
unit
7
/
8" (607 mm)
23
unit
1
/
min.
(min. 13 mm)
2"
90°
90°
Opposite hinges
measurements in inches and mm
Page | ϴ
Do not place one appliance with Right Hinge next to an appliance with a Left Hinge.
607mm
23 7/8 in
1224mm
48 3/16
in
607mm
23 7/8 in
13mm
½ in
(MÍNIM
UM)
!
Interférence
Ventilation
The Wine Reserve unit is ventilated only at the Toe-Kick in the base. Never cover that area or place
anything in front of it. Otherwise the refrigeration cooling performance will be affected and the unit must
work harder increasing power consumption.
Additionally, make certain all 4 leveling legs are extended (unit height approximately 34¾”), so that
there is sufficient airflow underneath the appliance.
Connecting the appliance
After installing the appliance, wait at least 1 hour to turn on the appliance. During transportation the oil
in the compressor may have flowed into the refrigeration system.
Before switching ON the appliance for the first time, clean the interior of the appliance (see chapter
“Cleaning the appliance” in the Use & Care Guide).
Page | 9
Electrical connection
AAA
A
A
WARNING:
These installation instructions are intended for use by qualified installers.
WARNING:
Avoid the risk of an electric shock!
Insert into a grounded receptacle.
Never remove grounding phase.
Do not use any adapters.
Do not use any extension cords.
WARNING:
It is the customer’s responsibility to insure that the appliance installation is in compliance with all national
and local electrical codes and ordinances. Non-compliance with these instructions may result in death,
fire or an electric
The receptacle must be near the appliance, 61” (1550mm) to the right of the appliance or 37” (940mm)
to the left of the appliance, and also freely accessible following installation of the appliance for future
service.
24
(615 mm)
The appliance complies with protection class I. Connect the appliance to 115 V/ 60Hz alternating
current via a correctly installed receptacle with grounded terminal.
The appliance comes with a UL registered 3-wire power
requires a 3-pole receptacle.
shock.
3
/16"
4"
(102 mm)
9
24
/16"
(624 mm)
:
1" (25.4 mm)
Recommended area for installation
connection - a 2
1
/2" (63 mm) diameter
hole is recommended.
B:
Location of power cord - approximately
36"
(915 mm)
15" (381 mm) from base of appliance.
1
5
/8"
(130 mm)
4"
(102 mm)
For flush installation, recommend outlet to be
placed to the side of the unit and not directly behind.
measurements in inches and mm
cord NEMA 5-15p type. The ap
Never remove the grounding phase
pliance
Page | ϭϬ
WARNING:
HOLE
Never connect the appliance to electronic energy saver plugs.
This appliance can be used with mains and sine-controlled inverters. Main controlled inverters are used
for photovoltaic systems which are connected directly to the national grid.
Sine-controlled inverters must be used for isolated applications (e.g. on ships or in mountain lodges)
which are not connected directly to the national grid.
The appliance requires a 3-pole socket. The socket should be connected by an electrician only.
Where there is a 2-pole standard wall socket, it is the responsibility of the customer to have this socket
replaced with a correctly grounded 3-pole wall socket. Do not use any adapter plugs.
Be sure that the location of your Wine Reserve has a near and accessible electric socket.
2-pole standard wall socket must be replaced with a 3-pole grounded socket. Do not use adapters.
Door opening.
The door of your Wine Reserve is configured by default to have an aperture up to 110°. This makes for
easy access to the wine racks for loading or cleaning. However, if the appliance is installed under
counter, it is recommended to install the Door Stopper Pins in the hinge to avoid hitting the wall, cabinets
or another appliance installed next to the Wine Reserve.
To install the Door Stopper Pin follow the next instructions:
1. Remove the Top Hinge Cover by pulling it to the opposite direction of the Hinge. This will uncover
the Hinge mechanism and the hole for the Door Stopper Pin.
Page | 1ϭ
2mm
675mm
26 1/2”
66mm
2 1/2”
603mm
90°
Now, the door opens only 90°
2. Position the door at less than 90° so the mechanism of the hinge does not obstruct the hole and
METALLIC RIB
OPEN SLOT
locks here
under this tab.
BOTTOM
HOLE
LESS THAN
PUSH
FIRMLY
insert the Door Stopper Pin into the hole.
3. Align the Pin with the bottom hole of the hinge and push the Pin firmly until it gets locked.
4. Now place back the Hinge Cover to protect the Hinge mechanism. First, be sure that the metallic
rib of the hinge is into the open slot of the Hinge Cover. Then, push and slide the Cover firmly in
the direction of the Hinge until it locks into its original place.
5. Be sure that the Hinge Cover is locked in its place. It is important to place the Hinge Cover back
because it helps to protect the mechanism of the Hinge and also your fingers from the
mechanism.
110°
The Cover
And locks
Page | 1Ϯ
Installing the anti-tip-brackets
The appliance includes two anti-tip-brackets. If your cabinetry is not designed for the specific dimensions
of your appliance, or if you plan to use the appliance as a free-standing unit, you should use these
brackets to avoid your appliance tilting due to unbalanced overweight in situations where the door is open
and several Wine Racks are pulled out.
WARNING
To avoid the appliance tilting due to unbalanced overweight do not pull out all the Wine Racks at the
same time. Always push the Wine Rack into the cabinet before pulling out another Wine Rack.
For free-standing use
1. Consider the distance necessary for the appliance to be flush with the front of your cabinetry. If
there is no cabinetry, put the unit close to the wall, then take the measurement of the space at the
back, between the unit and the wall.
2. Based on the measured distance between the back of the unit and the wall, bend the anti-tip
bracket (included with the unit) from the pointed lines to form a “step” with the same Distance
measured.
Bend from here
And here
Anti-tip-bracket.
2 pieces.
Adhesive foam Distance measured
NOTE: The adhesive foam must be at the bottom of the
Resultant formed “step”.
step, never on the reverse side.
Page | 1ϯ
3. Peel the adhesive foam and paste the anti-tip-bracket at both sides on the back of the appliance
as shown in the illustrations.
Paste the anti-tip-bracket to
the back of the appliance.
4. With the anti-tip-brackets pasted on the back of the appliance, slide the appliance to the wall until
the anti-tip-bracket is touching the wall.
Using the screws provided, fasten the anti-tip-bracket to the wall for both sides.
NOTE: Do not fasten the unit to dry wall. Be sure to attach the unit to a solid surface.
Screw the bracket
to the wall.
Repeat on the
other sid
e.
Page | 1ϰ
For under counter use
1. Consider the distance necessary for the appliance to be flush with the front of your cabinetry.
2. Take the measurement from the top of the cabinet of the unit to the bottom of the counter.
The measurement X”(mm) may vary depending on the design of the counter, extension of the
legs of the product, etc.
610mm
24”
Unit
Thermador Wine Reserve
Top View
Distance = X” (mm)
NOTE: the Distance = X”(mm) may vary
depending on the design of your cabinetry.
3. Based on the Distance = X” (mm) between the appliance and the counter, bend the anti-tipbrackets included with the appliance on the pointed lines to form a “step” 1/16” (2mm) smaller
than the Distance = X” (mm) measured.
Bend from here
Adhesive foam
Distance = X”- 1/16”
(X mm – 2mm)
And here
Anti-tip-bracket.
2 pieces.
Resultant formed “step”.
NOTE: The adhesive foam must be at the
bottom of the step, never on the reverse side.
Page | 1ϱ
bracket near the corners.
4. Peel the adhesive foam and paste the anti-tip-bracket at the front on the top of the cabinet of the
Slide the appliance into
the cabinet until the front
the counter to fix the unit.
C O U N T E R
A P P L I A N C E
appliance, near the corners as shown in the picture:
5. Slide the appliance into the cabinet until the front of the appliance is flush with the front of the
cabinetry. Check that nothing interferes or obstructs the anti-tip-bracket while sliding under the
counter.
surfaces are flush.
Paste the anti-tip-
Using the screws provided,
screw the anti-tip bracket to
Check that nothing obstructs
the anti-tip-bracket.
Page | 1ϲ
Installing the overlay frame
(For T24UW800LP and T24UW800RP models only)
If you plan to install a custom overlay frame, you will need to create the frame yourself or consult a
qualified cabinetmaker or carpenter.
$SULQWDEOHWHPSODWHWRKHOSZLWKFXVWRPSDQHOFRQVWUXFWLRQLVDYDLODEOHRQWKH7KHUPDGRUZHEVLWH.
IMPORTANT:
- The thickness of the overlay frame must be ¾” (19mm).
- Overlay frame must not weight more than 10lbs (4.54kg).
- Overlay frame weighting more than recommended may cause damage to your appliance.
- To install the frame, use only the screws included in the “installation kit”.
Create the custom overlay frame using the dimensions shown.
IMPORTANT: The following graphics shows a custom frame for a door with hinges installed on the righthand side. If your Wine Reserve has hinges installed on the left-hand side, rotate the custom frame 180°
so the makings will be on the left.
For detailed dimensions, see the frame specifications in Addendum A.
IMPORTANT: It is recommended to install the custom overlay frame with the help of another person.
Page | 1ϳ
1. Install the custom handle of your preference on the overlay frame before installing the frame on
Install custom
Overlay Frame with
custom handle
Door
Flat screw flush with surface
Overlay Frame with
Door
Round head screw hidden in a
recession on the overlay.
A
B
C
D
A
B
C
D
the door.
Every custom handle is different and it is the responsibility of the customer to make the
necessary adjustments to place the handle on the overlay frame.
The screws used to affix the custom handle to the frame must be flat and flush with the surface of
the frame; if the screws are not flat, then consider making a recession on the overlay, enough to
hide the head of the screw below the surface of the overlay, otherwise the screws will interfere
with the correct placement of the overlay on the door.
custom handle
handle first.
2. Locate and identify every pair of holes on the overlay frame corresponding with the holes on the
door. Every hole must be aligned to screw and fasten the overlay to the door.
Page | 1ϴ
These holes
3. Remove the gasket from the corners of the door pulling it gently until the two screws and two
Align door and frame
Fasten together
holes are visible. The two holes must be accessible to screw the overlay frame to the door.
There are 8 holes total, two per corner.
NOTE: It is not necessary to remove the entire gasket from the door, just from the corner, enough
to access to the holes.
4. Align the overlay frame with the door and hold them firmly together while screwing them. It may
be easier with the help of another person to hold and keep the frame in place while fastening.
Using the 8 screws included in the installation kit, fasten the overlay frame to the door.
must be
accessible.
Page | 1ϵ
5. Once the overlay frame is securely attached to the door with the 8 screws, put the gasket back in
Put gasket back in its place
its place pressing it against the door until all is even and firm into its channel.
6. Now, the overlay frame is ready.
Page | ϮϬ
Customer Service Information
If service becomes necessary, contact your dealer or an authorized service center. Do not attempt to
repair the appliance yourself. Any work performed by unauthorized personnel may void the warranty. If
problem persists, take the following steps (in the order listed below) until the problem is corrected to your
satisfaction.
1. Contact your dealer or the Thermador Authorized Servicer in your area.
2. E-mail us from the Customer Service section of our web site, www.Thermador.com.
3. Write to us at the address below:
BSH Home Appliances Corporation.
1901 Main Street, Suite 600
Irvine, CA 92614
4. Call us at: 1-800-735-4328
Please be sure to include (if writing), or have available (if calling), the following information:
• Model Number
• Serial Number
• Date of Original Purchase
• Date Problem Originated
• Explanation of Problem
Also, if writing, please be sure to include a daytime phone number. (You will find the model number and
serial number information on the label located inside the cabinet on the opposite side of the hinge).
Page | 2ϭ
Loading...