Texas Instruments TPS2833DR, TPS2833D, TPS2832DR, TPS2832D Datasheet
TPS2832, TPS2833
FAST SYNCHRONOUS-BUCK MOSFET DRIVER
WITH DEADTIME CONTROL
SLVS195B – JANUARY 1999 – REVISED SEPTEMBER 1999
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
D
Floating Bootstrap or Ground-Reference
High-Side Driver
D
Active Deadtime Control
D
50-ns Max Rise/Fall Times and 100-ns Max
Propagation Delay — 3-nF Load
D
Ideal for High-Current Single or Mutiphase
Applications
D
2.4-A Typ Peak Output Current
D
4.5-V to 15-V Supply Voltage Range
D
Internal Schottky Bootstrap Diode
D
Low Supply Current . . . 3–mA T yp
D
–40°C to 125°C Junction-Temperature
Operating Range
description
The TPS2832 and TPS2833 are MOSFET drivers for synchronous-buck power stages. These devices are ideal
for designing a high-performance power supply using a switching controller that does not include suitable
MOSFET drivers on the chip. The drivers are designed to deliver 2.4-A peak currents into large capacitive loads.
Higher currents can be controlled by using multiple drivers in a multiphase configuration. The high-side driver
can be configured as a ground-reference driver or as a floating bootstrap driver. An adaptive dead-time control
circuit eliminates shoot-through currents through the main power FET s during switching transitions and provides
high efficiency for the buck regulator.
The TPS2832 has a noninverting input. The TPS2833 has an inverting input. The TPS2832/33 drivers, available
in 8-terminal SOIC packages, operate over a junction temperature range of –40°C to 125°C.
AVAILABLE OPTIONS
PACKAGED DEVICES
T
J
SOIC
(D)
–40°C to 125°C
TPS2832D
TPS2833D
The D package is available taped and reeled. Add R
suffix to device type (e.g., TPS2830DR)
Copyright 1999, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
D PACKAGE
(TOP VIEW)
1
2
3
4
8
7
6
5
IN
PGND
DT
V
CC
BOOT
HIGHDR
BOOTLO
LOWDR
TPS2832, TPS2833
FAST SYNCHRONOUS-BUCK MOSFET DRIVER
WITH DEADTIME CONTROL
SLVS195B – JANUARY 1999 – REVISED SEPTEMBER 1999
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
functional block diagram
DT
3
IN
V
CC
LOWDR
BOOTLO
HIGHDR
BOOT
PGND
1
4
8
7
6
5
V
CC
2
(TPS2832 Only)
(TPS2833 Only)
Terminal Functions
TERMINAL
NAME NO.
I/O
DESCRIPTION
BOOT 8 I Bootstrap terminal. A ceramic capacitor is connected between BOOT and BOOTLO terminals to develop
the floating bootstrap voltage for the high-side MOSFET. The capacitor value is typically between 0.1 µF
and 1 µF . A 1-MΩ resistor should be connected across the bootstrap capacitor to provide a discharge path
when the driver has been powered down.
BOOTLO 6 O This terminal connects to the junction of the high-side and low-side MOSFETs.
DT 3 I Deadtime control terminal. Connect DT to the junction of the high-side and low-side MOSFETs
HIGHDR 7 O Output drive for the high-side power MOSFET
IN 1 I Input signal to the MOSFET drivers (noninverting input for the TPS2832; inverting input for the TPS2833).
LOWDR 5 O Output drive for the low-side power MOSFET
PGND 2 Power ground. Connect to the FET power ground.
V
CC
4 I Input supply. Recommended that a 1 µF capacitor be connected from VCC to PGND.
TPS2832, TPS2833
FAST SYNCHRONOUS-BUCK MOSFET DRIVER
WITH DEADTIME CONTROL
SLVS195B – JANUARY 1999 – REVISED SEPTEMBER 1999
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
detailed description
low-side driver
The low-side driver is designed to drive low Rds(on) N-channel MOSFETs. The current rating of the driver is
2 A, source and sink.
high-side driver
The high-side driver is designed to drive low Rds(on) N-channel MOSFETs. The current rating of the driver is
2 A, source and sink. The high-side driver can be configured as a ground-reference driver or a floating bootstrap
driver. The internal bootstrap diode, is a Schottky for improved drive ef ficiency . The maximum voltage that can
be applied between the BOOT terminal and ground is 30 V.
deadtime (DT) control
†
Deadtime control prevents shoot through current from flowing through the main power FETs during switching
transitions by controlling the turn-on times of the MOSFET drivers. The high-side driver is not allowed to turn
on until the gate drive voltage to the low-side FET is low, and the low-side driver is not allowed to turn on until
the voltage at the junction of the power FET s (Vdrn) is low; the DT terminal connects to the junction of the power
FET s.
IN
†
The IN terminal is a digital terminal that is the input control signal for the drivers. The TPS2832 has a noninverting
input; the TPS2833 has an inverting input.
†
High-level input voltages on IN and DT must be greater than or equal to VCC.
TPS2832, TPS2833
FAST SYNCHRONOUS-BUCK MOSFET DRIVER
WITH DEADTIME CONTROL
SLVS195B – JANUARY 1999 – REVISED SEPTEMBER 1999
4
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
absolute maximum ratings over operating free-air temperature (unless otherwise noted)
†
Supply voltage range, V
CC
(see Note 1) –0.3 V to 16 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input voltage range:BOOT to PGND (high-side driver ON) –0.3 V to 30 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BOOTLO to PGND –0.3 V to 16 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BOOT to BOOTLO –0.3 V to 16 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IN (see Note 2) –0.3 V to 16 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DT (see Note 2) –0.3 V to 30 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Continuous total power dissipation See Dissipation Rating Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating virtual junction temperature range, T
J
–40°C to 125°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range, T
stg
–65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lead temperature soldering 1,6 mm (1/16 inch) from case for 10 seconds 260°C. . . . . . . . . . . . . . . . . . . . . . .
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. Unless otherwise specified, all voltages are with respect to PGND.
2. High-level input voltages on the IN and DT terminals must be greater than or equal to VCC.
DISSIPATION RATING TABLE
PACKAGE
TA ≤ 25°C
POWER RATING
DERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
D 580 mW 5.8 mW/°C 320 mW 232 mW
recommended operating conditions
MIN NOM MAX UNIT
Supply voltage, V
CC
4.5 15 V
Input voltage BOOT to PGND 4.5 28 V
electrical characteristics over recommended operating virtual junction temperature range,
V
CC
= 6.5 V, CL = 3.3 nF (unless otherwise noted)
supply current
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
V
CC
Supply voltage range 4.5 15 V
VCC =15 V 100 µA
V
CC
Quiescent current
VCC =12 V ,
f
SWX
= 200 kHz,
C
HIGHDR
= 50 pF,
BOOTLO grounded,
C
LOWDR
= 50 pF,
See Note 3
3 mA
NOTE 3: Ensured by design, not production tested.
TPS2832, TPS2833
FAST SYNCHRONOUS-BUCK MOSFET DRIVER
WITH DEADTIME CONTROL
SLVS195B – JANUARY 1999 – REVISED SEPTEMBER 1999
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics over recommended operating virtual junction temperature range,
V
CC
= 6.5 V, CL = 3.3 nF (unless otherwise noted) (continued)
output drivers
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
V
BOOT
– V
BOOTLO
= 4.5 V, V
HIGHDR
= 4 V 0.7 1.1
High-side sink
Duty cycle < 2%
,
tpw < 100 µs
V
BOOT
– V
BOOTLO
= 6.5 V, V
HIGHDR
= 5 V 1.1 1.5
A
(see Note 4)
(see Note 3)
V
BOOT
– V
BOOTLO
= 12 V, V
HIGHDR
= 10.5 V 2 2.4
-
V
BOOT
– V
BOOTLO
= 4.5 V, V
HIGHDR
= 0.5V 1.2 1.4
High side
source
Duty cycle < 2%
,
tpw < 100 µs
V
BOOT
– V
BOOTLO
= 6.5 V, V
HIGHDR
= 1.5 V 1.3 1.6
A
Peak output-
(see Note 4) (see Note 3)
V
BOOT
– V
BOOTLO
= 12 V, V
HIGHDR
= 1.5 V 2.3 2.7
current
VCC = 4.5 V, V
LOWDR
= 4 V 1.3 1.8
Low-side sink
Duty cycle < 2%
,
tpw < 100 µs
VCC = 6.5 V, V
LOWDR
= 5 V 2 2.5
A
(see Note 4)
(see Note 3)
VCC = 12 V, V
LOWDR
= 10.5 V 3 3.5
-
VCC = 4.5 V, V
LOWDR
= 0.5V 1.4 1.7
Low side
source
Duty cycle < 2%
,
tpw < 100 µs
VCC = 6.5 V, V
LOWDR
= 1.5 V 2 2.4
A
(see Note 4) (see Note 3)
VCC = 12 V, V
LOWDR
= 1.5 V 2.5 3
V
BOOT
– V
BOOTLO
= 4.5 V, V
HIGHDR
= 0.5 V 5
High-side sink (see Note 4)
V
BOOT
– V
BOOTLO
= 6.5 V, V
HIGHDR
= 0.5 V 5
Ω
V
BOOT
– V
BOOTLO
= 12 V, V
HIGHDR
= 0.5 V 5
V
BOOT
– V
BOOTLO
= 4.5 V, V
HIGHDR
= 4 V 45
High-side source (see Note 4)
V
BOOT
– V
BOOTLO
= 6.5 V, V
HIGHDR
= 6 V 45
Ω
Output
V
BOOT
– V
BOOTLO
= 12 V, V
HIGHDR
=11.5 V 45
resistance
V
DRV
= 4.5 V, V
LOWDR
= 0.5 V 9
Low-side sink (see Note 4)
V
DRV
= 6.5 V V
LOWDR
= 0.5 V 7.5
Ω
V
DRV
= 12 V, V
LOWDR
= 0.5 V 6
V
DRV
= 4.5 V, V
LOWDR
= 4 V 45
Low-side source (see Note 4)
V
DRV
= 6.5 V, V
LOWDR
= 6 V 45
Ω
V
DRV
= 12 V, V
LOWDR
= 11.5 V 45
NOTES: 3. Ensured by design, not production tested.
4. The pull-up/pull-down circuits of the drivers are bipolar and MOSFET transistors in parallel. The peak output current rating is the
combined current from the bipolar and MOSFET transistors. The output resistance is the Rds(on) of the MOSFET transistor when
the voltage on the driver output is less than the saturation voltage of the bipolar transistor.
deadtime
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
High-level input voltage
2 V
LOWDR
Low-level input voltage
Over the V
CC
range (see Note 3)
1 V
High-level input voltage
2 V
DT
Low-level input voltage
Over the V
CC
range
1 V
NOTE 3: Ensured by design, not production tested.
digital control terminals
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
High-level input voltage
2 V
Low-level input voltage
Over the V
CC
range
1 V
Loading...