PCM2900C/2902C/2906CEVM-U
User's Guide
Literature Number: SBAU195
September 2011
2
Copyright © 2011, Texas Instruments Incorporated
SBAU195–September 2011
Submit Documentation Feedback
Contents
1 Description ......................................................................................................................... 5
1.1 Block Diagram ........................................................................................................... 6
1.2 Connectors and Jumpers ............................................................................................... 6
1.3 Switch Settings .......................................................................................................... 6
2 Schematic and PCB ............................................................................................................. 7
2.1 PCM290xCEVM-U PCB ................................................................................................ 7
SBAU195–September 2011 Table of Contents
Submit Documentation Feedback
3
Copyright © 2011, Texas Instruments Incorporated
All trademarks are the property of their respective owners.
4
Contents SBAU195–September 2011
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
1 Description
The PCM2900C/2902C/2906CEVM-U (PCM290xCEVM-U) is an evaluation board for Texas Instruments'
newly developed USB interface codecs, the PCM2900C, PCM2902C, and PCM2906C. The PCM2900C
includes a PCM2900C device, a bus-powered USB codec without an S/PDIF interface. The PCM2902C
includes a PCM2902C device, a bus-powered USB codec with an S/PDIF interface. The PCM2906C
includes a PCM2906C device, a bus-powered (500 mA) USB codec with an S/PDIF interface. Each
evaluation board also includes operational amplifiers for line input/output buffers, a 3.3-V regulator, and a
USB connector.
For information about the differences between the PCM290xCEVM-U and the DEM-PCM290xB-EVM
demonstration fixtures, see Application Report SBFA020.
The USB connector is mounted on the PCM2900C/2902C/2906C printed circuit board (PCB). Connecting
a USB interface to this USB connector enables the evaluation of codec performance.
The PCM2900C/2902C/2906C operates from the 5-V bus power supply of the USB. A 3.3-V IC regulator
is mounted on the board to provide power for analog circuitry and optionally for the codec.
Stereo audio output and input are available on two stereo mini-jacks.
The PCM2900C/2902B/2906B support the following USB features:
• Fully compliant with USB2.0 specification
• Full-speed transceivers
• Partially-programmable descriptors
• USB adaptive mode for playback
• USB asynchronous mode for record
• Bus-powered
• Full-speed transceivers
User's Guide
SBAU195–September 2011
PCM2900C/2902C/2906CEVM-U
SBAU195–September 2011 PCM2900C/2902C/2906CEVM-U
Submit Documentation Feedback
5
Copyright © 2011, Texas Instruments Incorporated
S/PDIF IN
S/PDIF OUT
USB
Connector
USB Interface
SW001 - SW003
Operation Control
3.3 V
REG
12-MHz XTAL
CN002
CN001
Lch
Rch
V L/R
OUT
V L/R
IN
DIN
DOUT
D+/–
V
BUS
OPA2353
LPF
OPA2353
LPF
CN101
Analog Out
Lch
Rch
CN102
Analog In
PCM2900C
PCM2902C
PCM2906C
GND GND
OUT IN
Description
1.1 Block Diagram
A block diagram of the PCM2900C/2902C/2906C is shown in Figure 1.
www.ti.com
Figure 1. PCM290xCEVM-U Block Diagram
1.2 Connectors and Jumpers
Table 1 summarizes the connectors and jumpers on the PCM290xCEVM-U. Figure 2 illustrates the pinout
for CN002.
Connector/Jumper Description
CN001
CN101 Audio LINE OUT (stereo mini-jack, 1.98 VPPfull-scale)
CN102 Audio LINE IN (stereo mini-jack, 1.98 VPPfull-scale)
CN002 S/PDIF IN/OUT for PCM2902C/PCM2906C
1.3 Switch Settings
• SW001: Human interface device (HID) key state (mute)
• SW002: HID key state (volume up)
• SW003: HID key state (volume down)
These switches should be set to logic level low when no HID is being used, or toggled high for HID control
of the respective parameters.
Table 1. Connectors and Jumpers
USB port (series B connector); connects to a USB
cable/connector
Figure 2. CN002 Pinout
6
PCM2900C/2902C/2906CEVM-U SBAU195– September 2011
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
www.ti.com
2 Schematic and PCB
This section presents the PCM290xCEVM-U PCB layout. A full-size schematic of the evaluation fixture is
appended to this user guide.
2.1 PCM290xCEVM-U PCB
Schematic and PCB
Figure 3. PCM2900CEVM/2902CEVM/2906CEVM-U Silkscreen
SBAU195–September 2011 PCM2900C/2902C/2906CEVM-U
Submit Documentation Feedback
7
Copyright © 2011, Texas Instruments Incorporated
Schematic and PCB
www.ti.com
Figure 4. PCM2900CEVM/2902CEVM/2906CEVM-U Top View
8
PCM2900C/2902C/2906CEVM-U SBAU195– September 2011
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
www.ti.com
Schematic and PCB
Figure 5. PCM2900CEVM/2902CEVM/2906CEVM-U Bottom View
SBAU195–September 2011 PCM2900C/2902C/2906CEVM-U
Submit Documentation Feedback
9
Copyright © 2011, Texas Instruments Incorporated
:DAEL NGISED :# EGDE
:ETA
D
:EMANELIF
:VER HCS
:VER B
CP
:FO:TEEHS
:YB NWARD
VER
HCS
VER B
CP
TEEHS
YB NWARD
FOETAD
E
MANELIF
IT
:OFNI EGAP
DAEL NGISED # EGDE# EGDEDAEL NGISED
:OFNI EGAP
IT
EMANELIF
ETAD
F
O
YB NWARD
TEEHS
VER BCP
VER HCS
82
72
6
2
5
2
4
2
3
2
2
2
1
2
0
2
9
1
81
71
61
5141
31
21
11
0
1
9
8
7
6
5
4
3
2
1
200U
1
2
3
1
2
3
1
2
3
101NC
esaC
tfe
L
thgiR
Shield
1
2
3
201NC
esaC
tfeL
thgiR
Shield
1
2
3
21
1X
600C
Fu
1
Fu1
Fu1
Fp8
1
Fp8
1
smhoM
1
500R
Fu01
101C
+
smhoK21
Fp033
50
1C
301C
Fu8100.0
301R
smhoK9.3
101R
smhoK2
1
701R
smho001
711C
Fu01
+
201C
Fu01
+
601R
smhoK21
601C
Fp033
Fu8100.0
smhoK9.3
401R
smhoK21
201R
smho001
801R
Fu01
811C
+
Fu01
701C
+
Fu8100.0
401C
411C
Fu01
+
111R
s
mhoK21
011C
F
p03
3
Fu8100.0
21
1C
smhoK9.3
311
R
smhoK21
511
R
smho001
901R
Fu01
801C
+
611C
Fu01
+
Fu01
511
C
+
smhoK21
2
11R
Fp033
111C
311C
Fu8100.0
411R
smhoK9.3
611R
smhoK2
1
011R
smho00
1
901C
Fu01
+
Fu1
4
00C
Fu
1
500C
DN
G
Fu1
3
00C
smho22
200R
300R
smho2
2
100C
Fu1.0
2
00C
Fu
1
700R
smhoK31
600R
smhoK72
100R
smhoK5.1
400R
smho0
smhoK5.1
1AR
smhoK5.1
3AR
2AR
smhoK5.1
A/N
C6092/C2092/C0092MCP-MED
1102 ,82 BEF
A
A
1
1
MD
5072/4072MCP-MED
Evaluation Board/Kit Important Notice
Texas Instruments (TI) provides the enclosed product(s) under the following conditions:
This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION
PURPOSES ONLY and is not considered by TI to be a finished end-product fit for general consumer use. Persons handling the
product(s) must have electronics training and observe good engineering practice standards. As such, the goods being provided are
not intended to be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations,
including product safety and environmental measures typically found in end products that incorporate such semiconductor
components or circuit boards. This evaluation board/kit does not fall within the scope of the European Union directives regarding
electromagnetic compatibility, restricted substances (RoHS), recycling (WEEE), FCC, CE or UL, and therefore may not meet the
technical requirements of these directives or other related directives.
Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/kit may be returned within 30
days from the date of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY
SELLER TO BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING
ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from all
claims arising from the handling or use of the goods. Due to the open construction of the product, it is the user’s responsibility to
take any and all appropriate precautions with regard to electrostatic discharge.
EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER
FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
TI currently deals with a variety of customers for products, and therefore our arrangement with the user is not exclusive.
TI assumes no liability for applications assistance, customer product design, software performance, or infringement of
patents or services described herein.
Please read the User’s Guide and, specifically, the Warnings and Restrictions notice in the User’s Guide prior to handling the
product. This notice contains important safety information about temperatures and voltages. For additional information on TI’s
environmental and/or safety programs, please contact the TI application engineer or visit www.ti.com/esh.
No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or
combination in which such TI products or services might be or are used.
FCC Warning
This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION
PURPOSES ONLY and is not considered by TI to be a finished end-product fit for general consumer use. It generates, uses, and
can radiate radio frequency energy and has not been tested for compliance with the limits of computing devices pursuant to part 15
of FCC rules, which are designed to provide reasonable protection against radio frequency interference. Operation of this
equipment in other environments may cause interference with radio communications, in which case the user at his own expense
will be required to take whatever measures may be required to correct this interference.
EVM Warnings and Restrictions
It is important to operate this EVM within the input voltage range of 0 V to +5 V and the output voltage range of 0 V to +5 V.
Exceeding the specified input range may cause unexpected operation and/or irreversible damage to the EVM. If there are
questions concerning the input range, please contact a TI field representative prior to connecting the input power.
Applying loads outside of the specified output range may result in unintended operation and/or possible permanent damage to the
EVM. Please consult the EVM User's Guide prior to connecting any load to the EVM output. If there is uncertainty as to the load
specification, please contact a TI field representative.
During normal operation, some circuit components may have case temperatures greater than +55°C. The EVM is designed to
operate properly with certain components above +55°C as long as the input and output ranges are maintained. These components
include but are not limited to linear regulators, switching transistors, pass transistors, and current sense resistors. These types of
devices can be identified using the EVM schematic located in the EVM User's Guide. When placing measurement probes near
these devices during operation, please be aware that these devices may be very warm to the touch.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products Applications
Audio www.ti.com/audio Communications and Telecom www.ti.com/communications
Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers
Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps
DLP® Products www.dlp.com Energy and Lighting www.ti.com/energy
DSP dsp.ti.com Industrial www.ti.com/industrial
Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical
Interface interface.ti.com Security www.ti.com/security
Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Mobile Processors www.ti.com/omap
Wireless Connctivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated
Loading...