Telefunken TTV149 Owner Manual

TTV-149

FULL ON SCREEN DISPLAY
255 PROGRAMS MEMORY
WITH INFRARED REMOTE CONTROL

Color Television

O W N E R ' S M A N U A L

Thank you for purchasing this colour television.
To fully enjoy your set from the very beginning, read this manual carefully and keep it
handy for future reference.

O W N E R ' S M A N U A L

O W N E R ' S M A N U A LO W N E R ' S M A N U A L

Installation and Safety

To ensure safe and reliable operation of the TV set, please observe the following precautions in installation,

operation and maintenance.

Attention:

１·Pay attention to the power supply cord before installing the TV set. Do not hang anything on the cord, and

avoid treading on the cord.

２·The slots on the back housing are designed for ventilation to prevent overheating. They must never be covered

or blocked. The TV set must not be placed near a heat source such as radiator, air ducts direct sunlight.

３·The outdoor antenna must not be erected close to HV lines or other power supply lines. Use extreme care when

erecting the antenna.

4·This TV must be connected to AC 240V 50Hz. Never connect to DC supply or any other power supply
5·Do not let any object fall into the ventilation openings of the TV set housing, nor let any liquid flow into the it

via the openings. This may cause the television to short circuit

6·Do not subject the TV set to rain, or use it in damp environment. In cleaning dust, be sure to remove the power

supply plug from its socket first. Do not clean the television with liquid detergent, use a damp cloth. Be sure to remove

the power supply plug from its socket and remove the antenna plug during a thunderstorm or when it will not be used

for long time, to avoid components being damaged by lightning.

7·If you use an indoor antenna, do not let it touch any electrical appliance, or normal reception of TV program may

be affected.

Safety:

1Never open the rear of the television. High Voltage components can cause fire, electric shock or injury. Qualified

TV service personnel should carry out all internal work.

2. Remove the power supply plug from its socket in case of the following conditions, and consult with service

personnel.

(1) The power cord and plug is damaged or cracked.

(2) Any object has fallen into or liquid flown into the TV set.

(3) The performance of TV set has deteriorated significantly or there is damage on the housing.

(4) The TV set will not operate normally according to the instructions.

3. Please remove the power supply plug from its socket when the TV set will not be used for long time.

The adjusting buttons and some sockets are in the front of the TV, other sockets are in the rear of the TV.

① Main power switch
② Remote control sensor
③ Power indicator
④ Program number down (P-) and up (P+)
⑤ Volume decrease (V-) and increase (V+)
⑥ Menu button
⑦ TV/AV button
⑧⑧⑧⑧ AV IN sockets
⑨⑨⑨⑨ Antenna input and AV IN/OUT sockets

7

6

V-MENU P-TV/AV

P+ V+

54 3

2

1

Connection of video signal

Zn cell etc.

If you wish to receive video signal from the video player (for example: VCR, VCD or DVD), you must insert the

player’s audio and video output plugs into this TV’s relevant AV input sockets which are two groups in the rear and

front of the TV respectively. As the audio input of the TV is monophonic, be careful not to insert two audio inputs (L

and R) into each group’s two sockets at the same time, and the sockets in the front and the rear can not be used at the

same time. Then press the TV/AV button to get the picture of video signal.

The TV can broadcast the audio and video signals of received programs from the antenna. The output sockets are in

the rear panel (AV-OUT).

Connection of antenna：

The RF signal received from antenna is received through the RF input socket in the rear panel. In order to get a

good reception, it is necessary to use an outdoor antenna or common antenna TV (CATV) cable .The 75Ω coaxial

cable is recommended for eliminating the interference and noise lines resulting from mis-matched impedance .If you
use the 300Ω parallel flat cable, please connect with 300Ω-75Ω adapter according to the following figure.

(300Ω)

(75Ω)

(300Ω-75Ω)

Battery installation (as shown in figure)

(1) Open the cover.

(2) Put in the batteries. Be sure
that the polarity (+or-)of the
batteries matches that of marks
inside the remote control.

(3) Replace the cover.

If following happens, replace with new
batteries. For example: remote control does
not work normally or cannot control the TV
or is not stable, please replace batteries
according to the figure.
Attention: Exchange weak batteries to
prevent leakage of battery acid into the
remote control. Do not charge, short circuit,
heat or burn normal batteries. Do not use
batteries, such as soda cell and C-

Function buttons of remote control

1. TV/AV Button

Press AV button to receive signal connected to AV Inputs. Press it

again to switch back to TV program.

2. Mute Button

Press this button to mute the sound. Press it again to restore the

sound. Press V+ may also be used to restore the sound.

3. Game Button (see the operation method 9).

4. MENU Button (see the operation method 3).

5. Volume Control Button V+/V-

Press the button [V+] to upward the selected one, press the button

[V-] to make it reduce.

6. Picture Button

Adjust the picture mode (see the operation method 5).

7. Clock Button (see the operation method 6).

8. Program Number (0-9, -/--/---)

To select TV program, press 0-9 to select a single-digit program.

To select a two-digit or three-digit program, press the [-/--/---] button

once or twice, then press the number buttons. If the number is

beyond the maximum, its function will become invalid.

9. Sleep Button

To select time required before the television automatically turns
to standby mode. The maximum sleep time is 120 minutes，when you

press it once, the time will reduce 15 minutes. If you set the time of
sleeping ，it will delete automatically the set of OFF-TIME.

10. Standby Button

This controls power on/standby modes. Press this button once, it

will swap between working mode and standby mode. When TV is in

standby mode, it is in the state of low power consumption. The

screen is off and the indicator light is on.

11. PP (personal preference) Button

There are five models to select: “standard”, “soft ”, “vivid”, “light ”and “personal preference ”. Press this button, it
can display relevant state of picture. “Personal preference” is used for adjusting brightness, contrast, color etc. by

yourself, the adjusted state will be put automatically into memory.

12. Call Button OSD (on screen display)

Press it once for displaying the present condition. Press it again for canceling the display.

13. Program Selector Button P+/P-

Press these two buttons, the number of program will go up by one or decrease by one. Change the number of

program by pressing P+/P -,it will skip the number of program in "REMEMBER OFF" ( in PRESET menu, it displays
“REMEMBER OFF”) .If all programs are in the state of "REMEMBER OFF"，it receives only program “0” when you
press this button .If only one program is in state of "REMEMBER ON"，it receives the only program which is in

"REMEMBER ON" .

14. Sound Button (See the operation method 10).

15. System Button (See the operation method 7).

16. Alternate Program

Press this button once，it can alternate between the present and previous program.