Telefunken TSOP4856ON1, TSOP4830ON1, TSOP4836ON1, TSOP4837ON1, TSOP4833ON1 Datasheet

TSOP48..ON1

Vishay T elefunken

Photo Modules for PCM Remote Control Systems

Description

The TSOP48..ON1 – series are miniaturized receivers
for infrared remote control systems. PIN diode and
preamplifier are assembled on lead frame, the epoxy
package is designed as IR filter.
The demodulated output signal can directly be de­coded by a microprocessor. TSOP48..ON1 is the
standard IR remote control receiver series, supporting
all major transmission codes.

16115

Features

 Photo detector and preamplifier in one package
 Internal filter for PCM frequency
 Improved shielding against electrical field

disturbance

 TTL and CMOS compatibility
 Output active low

Block Diagram

Input

PIN

AGC

Control

Circuit

Band
Pass

 Low power consumption
 High immunity against ambient light
 Continuous data transmission possible

(800 bit/s)

 Suitable burst length ≥10 cycles/burst

3

V

S

30 k

1

OUT

Demodu-

lator

2

GND

9612226

Document Number 82088

www.vishay .com

1 (7)Rev. 5, 29-Mar-01

TSOP48..ON1

Su ly Current (Pin 3)

Vishay Telefunken

Absolute Maximum Ratings

T

= 25_C

amb

Parameter Test Conditions Symbol Value Unit
Supply Voltage (Pin 2) V
Supply Current (Pin 2) I
Output Voltage (Pin 1) V
Output Current (Pin 1) I
Junction Temperature T
Storage Temperature Range T
Operating Temperature Range T
Power Consumption (T
Soldering Temperature t  10 s, 1 mm from case T

Basic Characteristics

T

= 25_C

amb

Parameter Test Conditions Symbol Min Typ Max Unit

Supply Current (Pin 3) VS = 5 V, Ev = 0 I

VS = 5 V, Ev = 40 klx, sunlight I
Supply Voltage (Pin 3) V
Transmission Distance Ev = 0, test signal see fig.7,

IR diode TSAL6200, IF = 250 mA
Output Voltage Low (Pin 1) I
Irradiance (30 – 40 kHz) Pulse width tolerance:

Irradiance (56 kHz) Pulse width tolerance:

Irradiance tpi – 5/fo < tpo < tpi + 6/f
Directivity Angle of half transmission distance ϕ

= 0.5 mA,Ee = 0.7 mW/m

OSL

tpi – 5/fo < tpo < tpi + 6/fo,

test signal see fig.7

tpi – 5/fo < tpo < tpi + 6/fo,

test signal see fig.7

 85 C) P

amb

2

o

SD
SH

S

d 35 m

V

OSL

E

e min

E

e min

E

e max

1/2

S

S

O

O

j

stg

amb

tot
sd

–0.3...6.0 V

5 mA

–0.3...6.0 V

5 mA

100 C
–25...+85 C
–25...+85 C

50 mW

260 C

0.8 1.1 1.5 mA

1.4 mA

4.5 5.5 V

250 mV

0.2 0.4 mW/m

0.3 0.6 mW/m

30 W/m

±45 deg

2

2

2

Application Circuit

TSAL62..

*) recommended to suppress power supply disturbances
**) The output voltage should not be hold continuously at a voltage below 3.3V by the external circuit.

www.vishay .com

2 (7)

16114

TSOP48..

3

1

2

4.7 mF *)

100 W *)

+5V

>10 kW

optional

mC

**)

GND

Document Number 82088

Rev. 5, 29-Mar-01

Suitable Data Format

The circuit of the TSOP48..ON1 is designed in that
way that unexpected output pulses due to noise or
disturbance signals are avoided. A bandpassfilter, an
integrator stage and an automatic gain control are
used to suppress such disturbances.
The distinguishing mark between data signal and
disturbance signal are carrier frequency, burst length
and duty cycle.

The data signal should fullfill the following condition:

• Carrier frequency should be close to center
frequency of the bandpass (e.g. 38kHz).

• Burst length should be 10 cycles/burst or longer.

• After each burst which is between 10 cycles and 70

cycles a gap time of at least 14 cycles is necessary.

• For each burst which is longer than 1.8ms a
corresponding gap time is necessary at some time in
the data stream. This gap time should be at least 4
times longer than the burst.

• Up to 800 short bursts per second can be received
continuously .

TSOP48..ON1

Vishay Telefunken

Some examples for suitable data format are:
NEC Code, T oshiba Micom Format, Sharp Code, RC5
Code, RC6 Code, R–2000 Code.

When a disturbance signal is applied to the
TSOP48..ON1 it can still receive the data signal.
However the sensitivity is reduced to that level that no
unexpected pulses will occure.

Some examples for such disturbance signals which
are suppressed by the TSOP48..ON1 are:

• DC light (e.g. from tungsten bulb or sunlight)

• Continuous signal at 38kHz or at any other

frequency

• Signals from fluorescent lamps with electronic
ballast with high or low modulation (see Figure A or
Figure B).

0 5 10 15 20

time [ms]

Figure A: IR Signal from Fluorescent Lamp with low Modulation

0 5 10 15 20

time [s]

Figure B: IR Signal from Fluorescent Lamp with high Modulation

Document Number 82088

www.vishay .com

3 (7)Rev. 5, 29-Mar-01