Telefunken TF-DBVT204 User Manual [ru]
MULTIMEDIA PLAYER WITH DVB-T2 RECEIVER/
МУЛЬТИМЕДИЙНЫЙ ПЛЕЕР
С DVB-T2 ПРИЕМНИКОМ
TF-DVBT204
Instruction manual
Руководство по
эксплуатации
Table of contents
Table of contents
Dear customer!
Thank you for purchasing our product. For safety, it is strongly recommended to read
this manual carefully before connecting, operating and/or adjusting the product and keep
the manual for reference in the future.
Table of contents
Before you start
Important safeguards
Utilization of the product
Connection
Connection
Operation
Control elements
Front panel
Rear panel
Remote controller
Changing the battery
General operation
OSD operation
Installation
Channel
Time
TV setting
Language
Other
USB
USB information
Scheduled recording
Time Shift
General information
Troubleshooting
Accessories
Supported formats
Specifications
2
3
3
3
4
4
5
5
5
5
6
6
7
8
8
9
9
9
10
10
10
11
11
11
12
12
13
13
14
2
Before you start
Important safeguards
• To prevent risk of fire or electric shock,
avoid merging the unit into the water or under
conditions of high humidity.
• Switch off the device from the socket, if
you’re not going to use it for a long time.
• Do not place objects on the device.
• Place the unit in a dry and ventilated area.
Eliminate proximity to heaters, do not expose
to sunlight, mechanical vibration, humidity and
dusty environment.
• It is possible to use a small amount of
neutral detergent to clean the device.
• Never use abrasive materials or organic
substances (alcohol, gasoline, etc.) to clean
the device.
• For repair and maintrnance contact only
authorized service centers.
• Before connecting the device to the mains,
please make sure the network cable can be
easily disabled at any time.
• Unplug from the mains and from the cable
television antenna, unless you intend to use it
for a long time, or before a thunderstorm. Do
not touch the unit, power cord and antenna
cable during a thunderstorm!
• Before you turn on the device, please
check the reliability of its connection to the
power supply and other devices.
• This unit can not receive television signals
during the movement of the vehicle.
• After prolonged exposure to cold, before
turning on leave the device for 1 hour at a
room temperature.
Utilization of the product
If you want to dispose this product, do not
mix it with general household waste. There is a
separate collection system for used electronic
products in accordance with legislation that
requires proper treatment, recovery and
recycling.
Please contact your local authorities for
the correct method of disposal. By doing so,
you will ensure that your disposed product
undergoes the necessary treatment, recovery
and recycling and thus prevent potential
negative effects on the environment and
human health.
Before you start
Before using this product, carefully read
the manual. After you read, save it for future
use. If necessary, contact your local dealer for
service.
All the illustrations in this manual are
schematic images, which may differ from
actual objects.
3
Connection
Connection
Connection
Antenna input
• Connect an external DVB-T antenna
(cable) connector to the antenna RF IN.
The signal in the block cable antenna
can fail to contain DVB-T/T2 signal due to the
carrier frequency altered by the cable network
operator.
In order to receive digital air TV signal
use an indoor or outdoor UHF antenna. Specify
the possibility and quality of digital air signal
with your local digital TV service providers. The
absence of a stable TV signal in your area cannot be a reason for returns or refunds without
an additional test of TV signal reception in your
area.
To increase the reception quality of
the state digital air television in rural areas or
at significant distances from a broadcasting
center we recomment using individual active
outdoor UHF antennae with a high resistance
factor, and placing them at maximum possible
heights.
RF LOOP output
• Connect the output RF LOOP jack to TV's
antenna input using a special adapter (not
included) for supplying an analog TV signal.
the supplied RCA-type cable.
Composite video (CVBS) output
• Connect the yellow video output to the
composite video input on your TV using
the included RCA cable for transmitting the
composite video signal.
HDMI-out
• If your TV has an HDMI video input,
connect it to an HDMI output of this unit using
a special HDMI cable (not included).
Coaxial output
• Connect the coaxial digital audio output to
the input of an amplifier to transmit the audio
signal to the amplifier using a special coaxial
cable (not included).
Stereo audio output
• Connect the left (white) and right (red)
terminal of the stereo audio output to the
corresponding audio inputs on your TV using
4
4
Controllers
Operation
Top panel
1. IR sensor
2. USB port
3. DC input
Rear panel
Operation
1
2
3
4 5 6 7 8 9 10
4. Antenna input
5. Antenna output
6. Coaxial output
7. Left audio output
8. Right audio output
9. Video output
10. HDMI output
5
5
Operation
Operation
Remote controller
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
1. STANDBY button
2. INFO button
3. EPG button
4. AUDIO button
5. MENU button
6. CH+ button/UP cursor button
7. ОК button
8. VOL- button/LEFT cursor button
9. CH- button/DOWN cursor button
10. FAVOURITE button
11. Number buttons
16
17
18
19
20
21
22
23
24
25
26
27
12. REV/FWD buttons
13. PAUSE button
14. PLAY button
15. Red/Green/Yellow/Cyan buttons
16. MUTE button
17. TTX button
18. PVR button
19. SUBTITLE button
20. EXIT button
21. VOL+ button/RIGHT cursor buttons
22. TV/RADIO button
23. RECALL button
24. GOTO button
25. PREV/NEXT buttons
26. STOP button
27. REPEAT button
Changing the battery
1. Remove the battery compartment cover
on the back of the RC.
2. Insert two AAA batteries into the battery
compartment making sure that the correct
polarity is observed.
3. Install the cover back.
• The RC should be pointed at remote
sensor within 8 meters and within 30 degrees
at the left or the right side.
• Take the battery out of the RC if it is not
used for a long time.
• Do not mix new and used batteries or
different types of batteries. Weak batteries can
leak and severely damage the RC.
• Do not expose the RC to shock, liquids,
and do not place it in an area with high
humidity.
6
6
Operation
General operations
STANDBY
When this unit is connected to the mains,
it goes into operation mode. When the unit is
running, press STANDBY button to turn the
device into sleep mode. In sleep mode, press
STANDBY button on the remote to turn the
device from sleep mode.
INFO
When viewing a TV channel, press this
button to display/hide the menu pages
containing various information about the current
channel (frequency, reception level etc.).
EPG
Press EPG button to display the menu of
the electronic TV guide (Electronic Program
Guide), which displays the schedule of
programs for a certain period of time for each
available channel. Using this function, you can
easily find programs you are interested in. Use
UP/DOWN cursor buttons to select the desired
TV program. Use LEFT/RIGHT cursor buttons
to switch pages of the interactive program
guide.
EPG-information cannot work if the
service is not provided by operator.
AUDIO
Press AUDIO to select the audio language
or audio channel, if this choice is supported by
the current channel.
CH+/CH-
Press these buttons to select the previous or
next channel.
Cursor
Press these buttons to navigate through the
various menus.
OK
Press this button to confirm the selection
options in the menu.
VOL-/VOL+
Press these buttons to adjust the sound
volume level.
FAVOURITE
Go to “MENU”—“Channel”—“TV Channel
Editor”-use cursor to select the channel that
you want to make favourite--press “favourite”
button on RC—use left/right cursor to choose
which item(music/movie/shopping/car,etc) you
want to divide it in—press “OK” to confirm and
“EXIT” to exit menu.
While watching TV channels, press
“FAVOURITE” button first, and the “favouite
off” line will be shown on the TV screen. In
this mode, you can switch between all TV
channels. When pressing the “FAVOURITE”
button for a second time, it will simply switch
between your favourite channels.
The number buttons
Press number buttons to enter the channel
number you want or other numbers (such as
passwords, play time, etc.).
REV/FWD
When playing a media file, press these
buttons for fast forward or backward playback.
PAUSE
When playing a media file, press this button
to set the playback to pause.
PLAY
Click this button to start playing a media file.
Red/Green/Yellow/Cyan buttons
Press the colored buttons to perform various
operations in the edit menu of channels,
teletext recording.
Operation
MUTE
Press this button to enable/disable the sound.
7
7
Operation
Operation
TTX
Press this button to enable or disable the
Teletext (Teletext is not supported by some TV
channels).
PVR
When a USB drive is connected to this unit,
while watching TV channels press PVR to
start recording video from the channel to USB.
Press STOP button to stop recording.
SUBTITLE
Click this button to select subtitle language,
if this choice is supported by the current
channel.
TV/RADIO
Press this button to switch between TV and
radio.
RECALL
Click this button to select the last-viewed
channel.
GOTO
During playback of video file, press this
button to open the window in which with the
help of number buttons you can input the file
playback time to start playback from. After
entering the time, press OK button to confirm.
PREV/NEXT
When playing a media file, press these
buttons to select previous/next file.
STOP
When playing a media file, press this button
to stop playback.
REPEAT
When playing a media file, press this button
to select the repeat mode: Repeat a single file,
folder repeat, repeat all the content, cancel
repeat (repeat modes available may vary
depending on different types of files).
OSD operation
1. Press MENU button to enter the setting
menu displayed on the screen.
2. Press LEFT/RIGHT cursor buttons on the
RC to select setting page.
3. Press OK button on the RC to go to the
parameter list.
4. Press UP/DOWN cursor buttons on the
RC to select a parameter to adjust.
5. Press LEFT/RIGHT cursor buttons on the
RC to adjust the selected parameter.
6. Press MENU button to return to the
previous menu page. Press EXIT button on the
RC to quit the menu.
Some menu items may be in grey color,
in this case they are not adjustable. Pictures
of OSD menu are for reference only; they may
differ from the real screens.
Installation
Antenna setting
Country setting
Tuner System
Auto Scan
Manual Scan
EXIT ОК
Return Confirm
• Antenna setting: this option is intended to
power an active antenna.
• Country setting: select your country.
• Tuner System: T/T2/T+T2
• Auto scan: press OK button to start
automatic search and saving of all available
channels. Press MENU or EXIT button to quit
search.
• Manual scan: Press OK button to enter
the manual search menu. Press LEFT/RIGHT
cursor buttons to select the channel frequency.
Press OK button to start search of the new
Installation
8
8
channel. When the new channel is ready, it will
be addded to the channel list.
Channel
Time
Operation
Operation
Channel
TV channel editor
Radio channel editor
EPG
LCN
EXIT ОК
Return Confirm
• TV channel editor: Enter password
(0000) to access the channel editor menu.
You can edit the channel list using the
following functions: move, lock, delete.
Move: Press the Red button on the RC —
then select the program that you want to move
— press the Green button to mark the program
— press the Yellow button to move it to the
place you want.
Skip: Press the Red button on the RC —
then select the program you want to skip and
press the Blue button to skip it.
Lock: Choose a channel and press the
Green button on the RC; The channel will be
locked.
Delete: Choose a channel and press the
Yellow button on the RC; The channel will be
deleted.
• Radio channel editor:
The radio channels are edited in the same
manner.
• EPG: See «General operations» program
for more details about Electronic Program
Guide.
• LCN
Set logical channel number on/off.
GMT usage
Time zone
Set Date
Set Time
Sleep time
Summer time
Adv. Timer
EXIT ОК
Time
Return Confirm
• GMT usage: set the GMT time zones
automatically or manually.
• Time Zone: select your region time zone if
GMT usage is turned on.
• Set Date: Input current date if GMT usage
is turned off.
• Set Time: Adjust time settings if GMT
usage is turned off.
• Sleep time: select time period after which
the unit will automatically switch to sleep mode.
• Summer time: On/Off.
TV setup
TV format
TV mode
Video output
TV resolution
OSD transparency
Banner display time
EXIT ОК
Return Confirm
• TV format: 4:3 LB/4:3 PS/16:9 FIT/16:9
LB.
TV Setup
9
9
Loading...