Teledyne 430 User Manual

Toll-free Phone:

800-324-5190

Phone:

[phone]

Fax:

[phone]

Email:

[e-mail]

Website:

http://www.teledyne-api.com/

Copyright 2015-2016

08311C DCN7342

Teledyne API

02 September 2016

User Manual

Model 430

Compact Ozone Analyzer

© TELEDYNE API (TAPI)

9970 CARROLL CANYON ROAD

SAN DIEGO, CA 92131-1106

USA

Teledyne API – Model 430 Compact Ozone Analyzer

NOTICE OF COPYRIGHT

© 2015-2016 Teledyne API. All rights reserved.

TRADEMARKS

All trademarks, registered trademarks, brand names or product names
appearing in this document are the property of their respect ive owners and are
used herein for identification purposes only.

08311 DCN7342 i

Teledyne API – Model 430 Compact Ozone Analyzer

SAFETY MESSAGES

Important safety messages are provided throughout this manual for the purpose of
avoiding personal injury or instrument damage. Please read these messages carefully.
Each safety message is associated with a safety alert symbol, and are placed throughout
this manual and inside the instrument. The symbols with messages are defined as follows:

WARNING: Electrical Shock Hazard

HAZARD: St r ong oxidizer

GENERAL WARNING/CAUTION: Read the accompanying message for

specific information.

CAUTION: Hot Surface Warning

Note

Do Not Touch: Touching some parts of the instrument without protection or

proper tools could result in damage to the part(s) and/or the instrument.
Technician Symbol: All operations marked with this symbol are to be

performed by qualified maintenance personnel only.
Electrical Ground: This symbol inside the instrument marks the central

safety grounding point for the instrument.

CAUTION

GENERAL SAFETY HAZARD

This instrument should only be used for the purpose and in the manner
described in this manual. If you use the 430 in a manner other than that
for which it was intended, unpredictable behavior could ensue with
possible hazardous consequences.

NEVER use any gas analyzer to sample combustible gas(es).

Technical Assistance regarding the use and maintenance of the 430 or
any other Teledyne API product can be obtained by contacting Teledyne
API’s Technical Support Department:

Phone: [phone]

Email: [e-mail]

or by accessing various service options on our website at

http://www.teledyne-api.com/

.

ii 08311C DCN7342

Teledyne API – Model 430 Compact Ozone Analyzer

AVERTISSEMENT: Risque de choc électrique

DANGER: Oxydant puissant

AVERTISSEMENT GÉNÉRAL / MISE EN GARDE: Lire la consigne

MISE EN GARDE

Ne pas toucher

Pictogramme « technicien »

Mise à la terre

MISE EN GARDE

NE JAMAIS utiliser un analyseur de gaz pour échantillonner des gaz
combustibles!

CONSIGNES DE SÉCURITÉ

Des consignes de sécurité importantes sont fourn ies tout au long du présent m anuel dans le but d’éviter des
blessures corporelles ou d’endommager les instruments. Veuillez lire attentivement ces consignes. Chaque
consigne de sécuri té est représenté e par un pictogr amme d’aler te de sécurité; c es pictogram mes se retrouven t
dans ce manuel et à l’intérieur des instruments. Les symboles correspondent aux consignes suivantes :

complémentaire pour des renseignements spécifiques

: Surface chaude

sans les outils appropriés pourrait entraîner des dommages aux pièces ou à
l’instrument.

être effectuées uniquement par du personnel de maintenance qualifié.

de la mise à la terre sécuritaire de l’instrument.

Cet instrument doit être utilisé aux fins décrites et de la manière décrite dans
ce manuel. Si vous utilisez cet instrument d’une autre manière que celle pour
laquelle il a été prévu, l’instrument pourrait se comporter de façon imprévisible
et entraîner des conséquences dangereuses.

: Toucher à certaines parties de l’instrument sans protection ou

: Toutes les opérations portant ce symbole doivent

: Ce symbole à l’intérieur de l’instrument détermine le point central

08311 DCN7342 iii

Teledyne API – Model 430 Compact Ozone Analyzer

“Packing Components for Return to Teledyne API’s

WARRANTY

WARRANTY POLICY (02024J)

Teledyne API (TAPI), a business unit of Teledyne Instruments, Inc., provides that:
Prior to shipment, TAPI equipment is thoroughly inspected and tested. Should equipment

failure occur, TAPI assures its customers that prompt service and support will be available.
(For the instrument-specific warranty period, please refer to the “Limited Warranty” section
in the Terms and Conditions of Sale on our website at the following link:
http://www.teledyne-api.com/terms_and_conditions.asp).

COVERAGE

After the warranty period and throughout the equipment lifetime, TAPI stands ready to
provide on-site or in-plant service at reasonable rates similar to those of other manufacturers
in the industry. All maintenance and the first level of field troubleshooting are to be
performed by the customer.

NON-TAPI MANUFACTURED EQUIPMENT

Equipment provided but not manufactured by TAPI is warranted and will be repaired to the
extent and according to the current terms and conditions of the respective equipment
manufacturer’s warranty.

PRODUCT RETURN

All units or components returned to Teledyne API should be properly packed for
handling and returned freight prepaid to the nearest designated Service Center. After the
repair, the equipment will be returned, freight prepaid.

The complete Terms and Conditions of Sale can be reviewed at

http://www.teledyne-

api.com/terms_and_conditions.asp

CAUTION – Avoid Warranty Invalidation

Failure to comply with proper anti-Electro-Static Discharge (ESD) handling and
packing instructions and Return Merchandise Authorization (RMA) procedures
when returning parts f or repair or calibration m ay void your warranty. For anti-ESD
handling and packing instructions please refer to the manual, Fundamentals of
ESD, PN 04786, in its
Customer Service” section. The manual can be downloaded from our website at

http://www.teledyne-api.com; RMA procedures can also be found on our website.

iv 08311C DCN7342

Teledyne API – Model 430 Compact Ozone Analyzer

We recommend that this manual be read in its entirety before any attempt is

ABOUT THIS MANUAL

Note

made to operate the instrument.

CONVENTIONS USED

In addition to the safety symbols as presented in the Important Safety Information page,
this manual provides special notices related to the safety and effective use of the
analyzer and other pertinent information.

Special Notices appea r as follow s:

ATTENTION

COULD DAMAGE INSTRUMENT AND VOID WARRANTY

This special notice provides information to avoid damage to your
instrument and possibly invalidate the warranty.

IMPORTANT IMPACT ON READINGS OR DATA

Could either affect accuracy of instrument readings or cause loss of data.

Note

Pertinent information associated with the proper care, operation or
maintenance of the analyzer or its parts.

08311 DCN7342 v

Teledyne API – Model 430 Compact Ozone Analyzer

This page intentionally left blank.

vi 08311C DCN7342

Teledyne API – Model 430 Compact Ozone Analyzer Table of Contents

TABLE OF CONTENTS

Safety Messages ..............................................................................................................................................ii

Warranty ..........................................................................................................................................................iv

About This Manual .......................................................................................................................................... v

1. INTRODUCTION, SPECIFICATIONS, APPROVALS ................................ 9

Overview ............................................................................................................................................... 9 1.1.

Specifications ........................................................................................................................................ 9 1.2.

EPA Designation ................................................................................................................................. 10 1.3.

Approvals and Certifications ............................................................................................................... 10 1.4.

Safety ..................................................................................................................................... 10 1.4.1.

EMC (Pending)....................................................................................................................... 10 1.4.2.

Instrument Layout ............................................................................................................................... 11 1.5.

Front Panel ............................................................................................................................. 11 1.5.1.

Rear Panel ............................................................................................................................. 11 1.5.2.

Optional Rechargeable External Battery............................................................................................. 11 1.6.

2. GETTING STARTED ........................................................................... 12

Unpacking and Inspecting the Instrument .......................................................................................... 12 2.1.

Pneumatic Connections ...................................................................................................................... 13 2.2.

Internal Pump ......................................................................................................................... 13 2.2.1.

Electrical Connections ........................................................................................................................ 13 2.3.

Power ..................................................................................................................................... 13 2.3.1.

Analog Out ............................................................................................................................. 14 2.3.2.

Analog In ................................................................................................................................ 14 2.3.3.

Serial Communications .......................................................................................................... 15 2.3.4.

3. OPERATION ...................................................................................... 16

Display and Navigation ....................................................................................................................... 16 3.1.

Menu ................................................................................................................................................... 16 3.2.

View ....................................................................................................................................... 18 3.2.1.

Cal (Calibration) ..................................................................................................................... 18 3.2.2.

Config (Configure) .................................................................................................................. 19 3.2.3.

Data ........................................................................................................................................ 20 3.2.4.

Data Collection .................................................................................................................................... 21 3.3.

Internal Storage...................................................................................................................... 21 3.3.1.

SD Card ................................................................................................................................. 21 3.3.2.

4. MAINTENANCE AND SERVICE ........................................................... 22

Maintenance Schedule ....................................................................................................................... 22 4.1.

Service and Troubleshooting .............................................................................................................. 22 4.2.

Warnings and Errors .............................................................................................................. 23 4.2.1.

Technical Assistance .......................................................................................................................... 25 4.3.

5. PRINCIPLES OF OPERATION ............................................................ 26

6. SPARE PARTS LIST ........................................................................... 28

FIGURES

Figure 1-1. Model 430 Front Panel ...........................................................................................................................11

Figure 1-2. Model 430 Rear Panel ...........................................................................................................................11

Figure 2-1. Power Port Polarity ................................................................................................................................13

Figure 3-1. Model 430 Control Butto ns ....................................................................................................................16

Figure 3-2. Model 430 Menu Map ............................................................................................................................17

08311 DCN7342 vii