xx
TTR500RACK
ZZZ
Rackmount Kit
Installation Instructions
www.tek.com
P071349201*
*
071-3492-01
Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries
or suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are c overed by U.S. and foreign patents, issued and pending. Information in this publication
supersedes that in all previously published material. Specifica tions and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14150 SW Karl Braun Drive
P.O . Bo x 50 0
Beaverto
USA
For product information, sales, service, and technical support:
n, OR 97077
In North America, call 1-800-833-9200.
Worldwide, visit www.tek.com to find contacts in your area.
General safety
summary
Review the following safety precautions to avoid injury and prevent damage to
this product or any products connected to it.
To avoid potential hazards, use this product only as specified.
Only qualified personnel should perform service procedures.
To avoid damage to
equipment and personal
injury
Do not exceed rackmount weight ratings. Use this rackmount kit only for TTR500
instruments.
Use proper hardware. Do not interchange hardware. Use only specified mounting
screws.
Use care when installing and removing product from rack. Avoid pinching
fingers and hands w hen installing and removing. Do not force the product when
installi
Use only with specified products. Do not use rackmount on products for which
it was not intended. Refer to individual product manuals for details or contact
Tektronix Customer Service when in doubt.
ng. Gently pull the product out when removing.
TTR500RACK Rackmount Kit Installation 1
Kit description
Kit description
Supported products
The rackmount kit is a collection of parts that, once installed, holds one or two
Tektronix TTR500 Vector Network Analyz ers , for mounting onto a standard
19-inch equi
pment rack. To complete the installation, you need
Phillips #2 screwdriver
T10andT20Torxdrivers
3/8 inch nut driver (wrench or socket)
TTR503A
TTR506A
Kit parts list
Use the figure to identify the parts contained in this kit and assemble the
rackmount. Some hardware may not be necessary for your configuration.
Item
no. Name and description Qty. Notes
1
2
3
4
5
6
7
8
9 NUT
10
11 NU T PL AT E
12
BRACKET, MAIN
RACK SLIDE
RACK SAFETY STOP LEVER
RACK SAFETY STOP BUSHING
SCREW
–32*1/2, FLAT HEAD 100° PHILLIPS
#8
IDER SCREW
SL
#8–32*1/4 TORX T20
RACKMOUNT SCREW
#10–32*5/8 PHILLIPS
RACK RAIL, REAR
#10–32*3/8 LOCK WASHER
RACK RAIL, FRONT
#10–32*1/8, 3–POSITION
INSTRUMENT FEET SCREW
M3–L6, TORX T10
1
2
2
2
2
2
0
1
2
4
2
2
4
OPTIONAL USE
AVAI LAB LE ON IN ST R UM E NT
2 TTR500RACK Rackmount Kit Installation
Kit description
TTR500RACK Rackmount Kit Installation 3
Kit description
Installation
Use this procedure and refer to the illustration to assemble the rackmount
hardware and install the instrument into the rack.
1. Attach the front rack rail (10) to the rear r ack rail (8) using the #10–32x5/8
screws (7) and the #10–32x3/8 lock washer nut (9).
2. Attach the pair of rack kit rails to the rack frame using the #10–32x5/8 Phillips
screw (7). Optionally, you can also use the #10–32x1/8 3–position nut plate
(11) if the rack threads are damaged.
3. Attach the rack slide (2) to the main bracket (1) using the #8–32x5/16 Torx
T20 screw (6).
4. Attach the rack safety stop lever (3) to the main bracket (1) using the rack
safety stop bushing (4) and the #8–32x1/2 Phillips flat head 100° screw (5).
5. Slide the main bracket assembly (1) into the rack rail assembly.
6. Remove the four M 3 L6 Torx T10 screws (12) that are used to attach the
rubber feet to the bottom of the TTR500 instrument.
7. Use the M3 L6 Torx T10 screws (12) to attach the TTR500 instrument to
the main bracket assembly (1). The rackmount kit can support up to two
TTR500 instruments.
8. Secure the main bracket assembly to the rack frame using #10–32x5/8 Phillips
screws (7).
4 TTR500RACK Rackmount Kit Installation
Loading...