Tektronix TSG4100A Series, TSG4102A, TSG4106A, TSG4104A Installation And Safety Instructions
xx
TSG4100A Series
RF Signal Generators
ZZZ
Installation and Safety
Instructions
*P071339000*
071-3390-00
xx
TSG4100A Series
RF Signal Generators
ZZZ
Installation and Safety
Instructions
www.tek.com
071-3390-00
Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries
or suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication
supersedes that in all previously published material. Specifications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14150 SW Karl Braun Drive
P.O. Box 5 0 0
Beaverto
USA
For product information, sales, service, and technical support:
n, OR 97077
In North America, call 1-800-833-9200.
Worldwide, visit www.tek.com to find contacts in your area.
Table of Contents
Preface ............................................................................................................... 1
Product overview ..... ................................ ................................ ......................... 1
Documentation ................................................................................................. 2
Warranty .. .................................. ................................ ................................ ......... 3
Important safety information ................. ................................ ................................ ..... 4
General safety summary ...................................................................................... 4
Service safety summary.... ................................ .................................. ................. 6
Terms in this manual ........................................... ................................ ............... 7
Symbols and terms on the product........................................................................... 7
Compliance information ........................................................................................... 8
EMC compliance ............. ................................ .................................. ............... 8
Safety compliance ............................................................................................. 9
Environmental considerations............................................................................... 11
Operating requirements ....................... .................................. ................................ .. 12
Specifications.......... ................................ ................................ ........................ 12
Environmental ratings ................................ ................................ ........................ 13
Physical specifications ....................................................................................... 13
Preventative maintenance............ .................................. ................................ ...... 14
Connectors.......................................................................................................... 15
Getting started..... . ... . . . .... . ..... . ..... . ..... . ..... . .... . ..... . ..... . ..... . ... . . . .... . ..... . ..... . ..... . ..... . ... 18
Power on and power off procedures .............. ................................ .......................... 18
Front panel controls .................... .................................. ................................ .... 19
Предисловие .... ................................ ................................ .................................. 20
Описание изделия ........................................................................................... 21
Документация ............ .................................. ................................ .................. 22
Гарантия ........................................................................................................... 23
Важная информация по безопасности.................... ................................ .................... 25
Общие правила техники безопасности .................... .................................. ............ 25
Правила по технике безопасности при сервисном обслуживании ................................. 28
Условные обозначения в данном руководстве.............................. ............................ 28
Символы и условные обозначения на приборе .................. ................................ ...... 29
Информация о соответствии ................................................................................... 29
Соответствие требованиям по электромагнитной совместимости ................................. 29
Соответствие требованиям по технике безопасности ........................ ........................ 31
Правила охраны окружающей среды ............ ................................ ........................ 33
Условия эксплуатации........................................................................................... 34
Технические характеристики.................................. .................................. .......... 34
Показатели условий эксплуатации ....................................................................... 35
Физические характеристики............................................................................... 35
TSG4100A Series RF Signal Generators Installation and Safety Instructions i
Table of Contents
Профилактичес
Разъемы .......... ................................ .................................. ................................ 37
Приступая к работе ................ ................................ ................................ .............. 40
Процедуры включения и выключения питания................ .................................. ...... 40
Элементы управления на передней панели............................................................. 41
кое обслуживание.................................. ................................ ...... 36
ii TSG4100A Series RF Signal Generators Installation and Safety Instructions
Preface
This document contains the following information:
Product warranty information (See page 3.)
Product overview (See page 1.)
Product documentation list (See page 2.)
Product overview
Important
product or any products connected to it (See page 4.)
EMC (elec
which the instrument complies (See page 8.)
Electri
page 12, Operating requirements.)
Rear and
Front panel controls description (See page 19.)
Installation procedures (See page 18, Getting started.)
Power on and power off procedures (See page 18.)
The Tektronix TSG4102A, TSG4104A, a nd TSG4106A RF Signal Generators
feature a frequency synthesis technique that provides low phase noise, agile
modulation, fast settling, and virtually infinite frequency resolution. These
truments also include a dual baseband arbitrary waveform generator and
ins
built-in support for digital vector modulation.
safety precautions to avoid injury and prevent damage to this
tromagnetic compliance), safety, and environmental standards with
cal, power, and environmental requirements to use the product (See
front panel connectors description (See page 15.)
ch model has two front panel outputs with overlapping frequency ranges. The
Ea
front panel BNC output provides sine wave signals from DC to 62.5 MHz with an
adjustable DC offset, and amplitudes ranging from 1 mV
panel Type N connector output provides AC coupled, sine wave signals from 950
kHz to 2 GHz (TSG4102A), 4 GHz (TSG4104A), and 6 GHz (TSG4106A) with
power levels ranging from –110 dBm to +16.5 dBm.
TSG4100A Series RF Signal Generators Installation and Safety Instructions 1
RMS
to1V
. The front
RMS
Preface
Documentation
The following documents contain information specific to this product.
Table 1: Product documentation
Item Purpose Location
Installation and Safety Instructions
(this manual)
User Manual
Specifications and Performance
Verification Technical R eference
Declassification and Security
Instructions
Programmer Manual
Service Manual Provides information about how to service the
Provides safety and compliance information, basic
installation instructions, and connector descriptions.
This document contains information in English and
Russian.
Provides product operation and application information.
Provides product specifications and performance
verification procedures for checking instrument
performance.
Provides information for sanitizing the product.
Provides GPIB commands for remote access of the
instrument.
instrument, including adjustment and removal
procedures.
Printed manual and also
available on the product
documentation CD and at
www.tektronix.com/downloads
Product documentation
CD and available at
www.tektronix.com/downloads
Product documentation
CD and available at
www.tektronix.com/downloads
Available at
www.tektronix.com/downloads
Product documentation
CD and available at
www.tektronix.com/downloads
Available at
www.tektronix.com/downloads
2 TSG4100A Series RF Signal Generators Installation and Safety Instructions
Warranty
Warranty
Tektronix warrants that this product will be free from defects in materials and
workmanship for a period of three (3) years from the date of shipment. If any
such product
either will repair the defective product without charge for parts and labor, or will
provide a replacement in exchange for the defective product. Parts, modules
and replacement products used by Te ktronix for warranty work may be new or
reconditioned to like new performance. All replaced parts, modules and products
become the property of Tektronix.
In order to obtain service under this warranty, Customer must notify Tektronix
of the defect before the expiration of the warranty period and make suitable
arrange
packaging and shipping the d efective product to the service center designated by
Tektronix, with shipping charges prepaid. Tektronix shall pay for the return of the
product to Customer if the shipment is to a location within the country in which
the Tektronix service center is located. Customer shall be responsible for paying
all shipping charges, duties, taxes, and any other charges for products returned
to any
proves defective during this warranty period, Tektronix, at its option,
ments for the performance of service. Customer shall be responsible for
other locations.
This warranty shall not apply to any defect, failure or damage caused by improper
r improper or inadequate maintenance and care. Tektronix shall not be
use o
obligated to furnish service under this warranty a) to repair damage resulting from
attempts by personnel other than Tektronix r epresentatives to install, repair or
service the product; b) to repair damage resulting from improper use or connection
to incompatible equipment; c) to repair any damage or malfunction caused by the
use of non-Tektronix supplies; or d) to service a product that has been modified or
tegrated with other products when the effect of such modification or integration
in
increases the time or difficulty of servicing the product.
HIS WARRANTY IS GIVEN BY TEKTRONIX WITH RESPECT TO
T
THE PRODUCT IN LIEU OF ANY OTHER WARRANTIES, EXPRESS
OR IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. TEKTRONIX' RESPONSIBILITY TO REPAIR
OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE AND EXCLUSIVE
REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS
WARRANTY. TEKTRONIX AND ITS VENDORS WILL NOT BE LIABLE
FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR THE VENDOR
HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.
[W4 – 15AUG04]
TSG4100A Series RF Signal Generators Installation and Safety Instructions 3
Important safety information
Important saf
ety information
This manual c
for safe operation and to keep the product in a safe condition.
To sa fely pe
the end of this section.(See page 6, Service safety summary.)
General safety summary
Use the product only as specified. Review the following safety precautions to
avoid injury and prevent damage to this product or any products connected to it.
Carefully read all instructions. Retain these instructions for future reference.
Comply with local and national safety codes.
For correct and safe operation of the product, it is essential that you follow
generally accepted safety procedures in addition to the safety precautions specified
in this manual.
The product is designed to be used by trained personnel only.
Only qualified personnel who are aware of the hazards involved should remove
the cover for repair, maintenance, or adjustment.
ontains information and warnings that must be followed by the user
rform service on this product, additional information is provided at
To avoid fi re or personal
injury
This product is not intended for detection of hazardous voltages.
ersonal protective equipment to prevent shock and arc blast injury where
Use p
hazardous live conductors are exposed.
le using this product, you may need to access other parts of a larger system.
Whi
Read the safety sections of the other component manuals for warnings and
cautions related to operating the system.
When incorporating this equipment into a system, the safety of that system is the
responsibility of the assembler of the system.
Use proper power cord. Use only the power cord specified for this product and
certified for the country of use.
Do not use the provided power cord for other products.
Ground the product. This product is grounded through the grounding conductor
of the power cord. To avoid electric shock, the grounding conductor must be
connected to earth ground. Before making connections to the input or output
terminals of the product, make sure that the product is properly grounded.
Do not disable the power cord grounding connection.
4 TSG4100A Series RF Signal Generators Installation and Safety Instructions
Important safety information
Power disconne
source. See instructions for the location. Do not position the equipment so that
it is difficult to operate the power cord; it must remain accessible to the user at
all times to allow for quick disconnection if needed.
Observe all terminal ratings. To avo id fire or shock hazard, observe all ratings
and markings on the product. Consult the product manual for further ratings
information before making connections to the product.
Do not apply a potential to any terminal, including the common terminal, that
exceeds the maximum rating of that terminal.
Do not float the common terminal above the rated voltage for that terminal.
The measuring terminals on this product are not rated for connection to mains or
Category II, III, or IV circuits.
Do not operate without covers. Do not operate this product with covers or panels
removed, or with the case open. Hazardous voltage exposure is possible.
Avoid exposed circuitry. Do not touch exposed connections and components
when power is present.
Do not operate with suspected failures. If you suspect that there is damage to this
product, have it inspected by qualified service personnel.
ct. The power cord disconnects the product from the power
Disable the product if it is damaged. Do not use the product if it is damaged
or operates incorrectly. If in doubt about safety of the product, turn it off and
disconnect the power cord. Clearly mark the product to prevent its further
operation.
Examine the exterior of the product before you use it. Look for cracks or missing
pieces.
Use only specified replacement parts.
Use proper fuse. Use only the fuse type and rating specified for this product.
Wear eye protection. Wear eye protection if exposure to high-intensity rays or
laser radiation exists.
Do not operate in wet/damp conditions. Be aware that condensation may occur if
a unit is moved from a cold to a warm environment.
Do not operate in an explosive atmosphere.
Keep product surfaces clean and dry. Remove the input signals before you clean
the product.
Provide proper ventilation. Refer to the installation instructions in the manual for
details on installing the product so it has proper ventilation.
TSG4100A Series RF Signal Generators Installation and Safety Instructions 5
Important safety information
Slots and openi
otherwise obstructed. Do not push objects into any of the openings.
Provide a safe working environment. Always place the product in a location
convenient for v iewing the display and indicators.
Avoid improper or prolonged use of keyboards, pointers, and button p ads.
Improper or prolonged keyboard or pointer use may result in serious injury.
Be sure your work area meets applicable ergonomic standards. Consult with an
ergonomics professional to avoid stress injuries.
Use only the Tektronix rackmount hardware specified for this product.
Servicesafetysummary
The Service safety summary section contains additional information required to
safely perform service on the product. Only qualified personnel should perform
service procedures. Read this Service safety summary and the General safety
summar
To avoid electric shock. Do not touch exposed connections.
ngs are provided for ventilation and should never be covered or
y before performing any service procedures.
Do not service alone. Do not perform internal service or adjustments of this
product unless another person capable of rendering first aid and resuscitation is
ent.
pres
Disconnect power. To avoid electric shock, switch off the product power and
disconnect the power cord from the mains power before removing any covers or
panels, or opening the case for servicing.
e care when servicing with power on. Dangerous voltages or currents may exist
Us
in this product. Disconnect power, remove battery (if applicable), and disconnect
test leads before removing protective panels, soldering, or replacing components.
Verify safety after repair. Always recheck ground continuity and mains dielectric
strength after performing a repair.
6 TSG4100A Series RF Signal Generators Installation and Safety Instructions
Terms in this manual
These terms may appear in this manual:
WAR NI NG . Warning statements identify conditions or practices that could result
in injury or loss of life.
CAUTION. Caution statements identify conditions or practices that could result in
damage to this product or other property.
Symbols and terms on the product
Important safety information
These ter
The following symbol(s) may appear on the product:
ms may appear on the product:
DANGER indicates an injury hazard immediately accessible as you read
the mark
WARNING indicates an injury hazard not immediately accessible as you
read th
CAUTION indicates a hazard to property including the product.
ing.
emarking.
When this symbol is marked on the p roduct, be sure to consult the manual
to find out the nature of the potential hazards and any actions which have to
be taken to avoid them. (This symbol may also be used to refer the user to
ratings in the manual.)
TSG4100A Series RF Signal Generators Installation and Safety Instructions 7
Compliance information
Compliance in
EMC compliance
EC Declaration of
Conformity – EMC
formation
This section
environmental standards with which the instrument complies.
Meets intent of Directive 2004/108/EC for Electromagnetic Compatibility.
Compliance was demonstrated to the following specifications as listed in the
Official Journal of the European Communities:
EN 61326-1. EMC requirements for electrical equipment for measurement,
control
CISPR 11. Radiated and conducted emissions, Group 1, Class A
IEC 61000-4-2. Electrostatic discharge immunity
IEC 61000-4-3. RF electromagnetic field immunity
IEC 61000-4-4. Electrical fast transient / burst immunity
IEC 61000-4-5. Power line surge immunity
lists the EMC (electromagnetic compliance), safety, and
, and laboratory use.
123
1000-4-6. Conducted RF immunity
IEC 6
IEC 61000-4-11. Voltage dips and interruptions immunity
EN 61000-3-2. AC power line harmonic emissions
EN 61000-3-3. Voltage changes, fluctuations, and flicker
European contact.
ektronix UK, Ltd.
T
Western Peninsula
Western Road
Bracknell, RG12 1RF
United Kingdom
1
This product is intended for use in nonresidential areas only. Use in residential areas may cause electromagnetic
interference.
2
Emissions which exceed the levels required by this standard may occur when this equipment is connected to a
test object.
3
For compliance with the EMC standards listed here, high quality shielded interface cables should be used.
8 TSG4100A Series RF Signal Generators Installation and Safety Instructions
Compliance information
Australia / New Zealand
Declaration of
Conformity – EMC
Safety compliance
EU declaration of
conformity – low voltage
Complies with t
following standard, in accordance with ACMA:
CISPR 11. Radi
accordance with EN 61326-1:2006.
Australia / New Zealand contact.
Baker & McKenzie
Level 27, AMP Centre
50 Bridge Street
Sydney NSW 2000, Australia
This section lists the safety standards with which the product complies a nd other
safety c
Compliance was demonstrated to the following specification as listed in the
Official Journal of the European Union:
Low Voltage Directive 2006/95/EC.
ompliance information.
he EMC provision of the Radiocommunications Act per the
ated and Conducted Emissions, Group 1, Class A, in
nationally recognized
U.S.
testing laboratory listing
Canadian certification
Additional compliances
Equipment type
Safety class
EN 61010-1. Safety Requirements for Electrical Equipment for Measurement,
Control, and Laboratory Use – Part 1: General Requirements.
UL 61010-1. Safety Requirements for Electrical Equipment for Measurement,
Control, and Laboratory Use – Part 1: General Requirements.
CAN/CSA-C22.2 No. 61010-1. Safety Requirements for Electrical
Equipment for Measurement, Control, and Laboratory Use – Part 1: General
Requirements.
IEC 61010-1. Safety Requirements for Electrical Equipment for
Measurement, Control, and Laboratory Use – Part 1: General Requirements.
Test and measuring equipment.
Class1–groundedproduct.
TSG4100A Series RF Signal Generators Installation and Safety Instructions 9
Loading...