Teka BKSSL BPM Safety And Installation Instructions Manual

BEACON POLE MOUNT™ (BPM)

NEEDED

FOR

INSTALLATION:

5/64” & 1/8” Allen Wrench

Waterproof Wire Connectors

Gloves

Warning Hot Surface

Wear Gloves

High Voltage

By Others

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS

IMPORTANT - WEAR GLOVES TO AVOID GETTING FINGERPRINTS ON THIS PRODUCT. MANY TEKA ILLUMINATION PRODUCTS ARE DESIGNED TO NATURALLY PATINA.
OILS FROM YOUR SKIN WILL ACCELERATE THIS PROCESS WHERE TOUCHED AND ARE NEARLY IMPOSSIBLE TO REMOVE. THIS PROCESS OCCURS OVER TIME AND IS
DETERMINED BY THE INSTALLATION ENVIRONMENT.

INSTRUCTIONS PERTAINING TO

A RISK OF FIRE, OR INJURY TO

PERSONS IMPORTANT SAFETY

INSTRUCTIONS

Lighted fixture is HOT!
WARNING - To reduce the risk of
FIRE OR INJURY TO PERSONS:

Turn off/unplug and allow to cool before replacing LED.
Fixture gets HOT quickly! Contact only switch/plug when
turning on. Do not touch hot lens, guard, or enclosure.
Keep fixture away from materials that may burn.
Do not operate the luminaire fitting with a missing or
damaged shield. Do not touch the source at any time. Use

a soft cloth or gloves. Oil from skin may cause damage.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY

AND INSTALLATION INSTRUCTIONS

• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local and
Provincial Codes.

• Follow product label information and instructions.

• Qualified Personnel with appropriate personal protective
equipment must perform all servicing of this product.

• Before wiring to power supply and during servicing, turn off and
lock out power at fuse or circuit breaker before service.

• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause an
unsafe condition and void product warranty.

• Do not block light emanating from product in whole or part, as
this may cause an unsafe condition.

• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.

• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body.

• Replace LED assembly only with correct wattage and type of
power supply appropriate for LED assembly.

• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.

Pole Top Installation Instructions

Shade

Lens

Solid State BPM
(Beacon Pole Mount)

IMPORTANT LISTINGS AND CERTIFICATIONS

· Suitable for wet locations

Cap

Spacers

Base

Rings

3-1/2” O.D. Pole or Pole with

3-1/2” O.D Tenon
(Specify Separately)
(Pole By Others)

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS

40429 Brickyard Drive • Madera, CA 93636 • USA

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF TEKA ILLUMINATION AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF TEKA ILLUMINATION AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF TEKA ILLUMINATION IS STRICTLY FORBIDDEN.

DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF TEKA ILLUMINATION IS STRICTLY FORBIDDEN.

www.tekaillumination.com • [e-mail]

559.438.5800 • FAX [phone]

DATE

5-14-18

REFERENCE NUMBER

INS-2569-00

Phase 1 - Install Pole

1. Install 3-1/2” O.D. pole (By Others) or pole with
3-1/2” O.D. tenon (By Others, Specify Separately)
according to lighting plan and manufacturer’s
installation instructions. Install conduit (By
Others) to be used with this product.

2. Pull primary branch circuit wiring necessary for
installation (By Others). Pull incoming dimming
controls necessary for installation. (By Others).

Leave sufficient wire length in the pole for

future service.

Phase 2 - Fixture Installation (Pole Top Option)

DIM +

DIM -

BEACON POLE MOUNT™ (BPM)

Pole Top Installation Instructions

Red

1. Pull primary branch circuit wiring up to driver
bracket location at top of pole. Pull incoming
dimming controls to top of pole. Feed through
strain relief.

LINE

COM

GROUND

WIRING DIAGRAM

2. Make watertight connections from primary
branch circuit to driver leads using waterproof
wire connectors (By Others). Connect green
ground wire to ground wiring from driver.
Connect incoming dimming controls to driver
primary side dimming controls. Secondary side
is connected via quick disconnect. See wiring

diagram.

Driver

FIXTURE

Black

3. Place connections and driver on bracket into
pole. Rest bracket on pole top or tenon.

4. Make secondary connections via quick disconnect
from driver secondary side to fixture secondary
side.

4. Slide fixture over pole top. Secure with four (4)
1/4-20 screws using /1/8” Allen wrench. Make
sure the fixture is completely seated. Do not
overtighten.

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

40429 Brickyard Drive • Madera, CA 93636 • USA

www.tekaillumination.com • [e-mail]

559.438.5800 • FAX [phone]

DATE

5-14-18

REFERENCE NUMBER

INS-2569-00

BEACON POLE MOUNT™ (BPM)

NEEDED

FOR

INSTALLATION:

5/64” & 1/8” Allen Wrench

Waterproof Wire Connectors

Gloves

Warning Hot Surface

Wear Gloves

High Voltage

By Others

Adjustable Crescent Wrench

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS

IMPORTANT - WEAR GLOVES TO AVOID GETTING FINGERPRINTS ON THIS PRODUCT. MANY TEKA ILLUMINATION PRODUCTS ARE DESIGNED TO NATURALLY PATINA.
OILS FROM YOUR SKIN WILL ACCELERATE THIS PROCESS WHERE TOUCHED AND ARE NEARLY IMPOSSIBLE TO REMOVE. THIS PROCESS OCCURS OVER TIME AND IS
DETERMINED BY THE INSTALLATION ENVIRONMENT.

INSTRUCTIONS PERTAINING TO

A RISK OF FIRE, OR INJURY TO

PERSONS IMPORTANT SAFETY

INSTRUCTIONS

Lighted fixture is HOT!
WARNING - To reduce the risk of
FIRE OR INJURY TO PERSONS:

Turn off/unplug and allow to cool before replacing LED.
Fixture gets HOT quickly! Contact only switch/plug when
turning on. Do not touch hot lens, guard, or enclosure.
Keep fixture away from materials that may burn.
Do not operate the luminaire fitting with a missing or
damaged shield. Do not touch the source at any time. Use

a soft cloth or gloves. Oil from skin may cause damage.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY

AND INSTALLATION INSTRUCTIONS

• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local and
Provincial Codes.

• Follow product label information and instructions.

• Qualified Personnel with appropriate personal protective
equipment must perform all servicing of this product.

• Before wiring to power supply and during servicing, turn off and
lock out power at fuse or circuit breaker before service.

• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause an
unsafe condition and void product warranty.

• Do not block light emanating from product in whole or part, as
this may cause an unsafe condition.

• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.

• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body.

• Replace LED assembly only with correct wattage and type of
power supply appropriate for LED assembly.

• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.

Hinge Base Installation Instructions

Spacers

Shade

Lens

Solid State BPM
(Beacon Pole Mount)

IMPORTANT LISTINGS AND CERTIFICATIONS

· Suitable for wet locations

Cap

Base

Rings

3-1/2” O.D. Hinge Base Pole or

Hinge Base Pole with 3-1/2” O.D
Tenon (Specify Separately)

(Pole By Others)

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS

40429 Brickyard Drive • Madera, CA 93636 • USA

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF TEKA ILLUMINATION AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF TEKA ILLUMINATION AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF TEKA ILLUMINATION IS STRICTLY FORBIDDEN.

DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF TEKA ILLUMINATION IS STRICTLY FORBIDDEN.

www.tekaillumination.com • [e-mail]

559.438.5800 • FAX [phone]

DATE

5-14-18

REFERENCE NUMBER

INS-2569-01

Phase 1 - Install Pole

1. Install 3-1/2” O.D. pole (By Others) or pole with
3-1/2” O.D. tenon (By Others, Specify Separately)
according to lighting plan and manufacturer’s
installation instructions. Install conduit (By Others)
to be used with this product.

2. Pull primary branch circuit wiring necessary for
installation (By Others). Pull incoming dimming
controls necessary for installation. (By Others).

Leave sufficient wire length in the pole for

future service.

Phase 2 - Fixture Installation (Hinge Base Option)

BEACON POLE MOUNT™ (BPM)

Hinge Base Installation Instructions

DIM +

DIM -

Red

1. Remove base cover (if required). Open hinge base
on pole by loosening three (3) 1/2”-13 stainless
steel bolts using adjustable crescent wrench.

2. Hinge pole open for access to conduit and
branch circuit wiring. Pull branch circuit wiring
and dimming controls to splice location.

LINE

COM

GROUND

WIRING DIAGRAM

3. Make watertight connections from primary
branch circuit to driver leads using waterproof
wire connectors (By Others). Connect green
ground wire to ground wiring from driver.
Connect incoming dimming controls to driver
primary side dimming controls. Connect
secondary side of driver to wiring for fixture
leads. See wiring diagram.

Driver

FIXTURE

Black

4. Place driver, bracket and connections into pole.
Hinge pole back to upright position. Connect
secondary wiring to secondary side of driver.
Pull secondary wiring to top of pole. Length of
secondary wiring will vary with height of pole.
Leave length for future service.

5. Close hinge pole, then secure to base with
three (3) 1/2” I.D. flat washers, split lock
washers and three (3) 1/2”-13 stainless steel
bolts using an adjustable crescent wrench.

6. If pole comes with cover, place cover on base
of pole. Secure with four (4) 1/4”-20 hex screws
using 3/16” Allen wrench.

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

40429 Brickyard Drive • Madera, CA 93636 • USA

www.tekaillumination.com • [e-mail]

559.438.5800 • FAX [phone]

DATE

5-14-18

REFERENCE NUMBER

INS-2569-01

BEACON POLE MOUNT™ (BPM)

Hinge Base Installation Instructions

7. Make watertight connections using waterproof
wire connectors to connect fixture leads to
secondary leads from driver. Leave length for
future service. See wiring diagram.

8. Slide fixture over pole top. Secure with four (4)
1/4-20 screws using /1/8” Allen wrench. Make
sure the fixture is completely seated. Do not
overtighten.

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

40429 Brickyard Drive • Madera, CA 93636 • USA

www.tekaillumination.com • [e-mail]

559.438.5800 • FAX [phone]

DATE

5-14-18

REFERENCE NUMBER

INS-2569-01

BEACON POLE MOUNT™ (BPM)

NEEDED

FOR

INSTALLATION:

5/64”, 1/8”, 5/32” & 1/16” Allen Wrench

Waterproof Wire Connectors

Gloves

Warning Hot Surface

Wear Gloves

High Voltage

By Others

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS

IMPORTANT - WEAR GLOVES TO AVOID GETTING FINGERPRINTS ON THIS PRODUCT. MANY TEKA ILLUMINATION PRODUCTS ARE DESIGNED TO NATURALLY PATINA.
OILS FROM YOUR SKIN WILL ACCELERATE THIS PROCESS WHERE TOUCHED AND ARE NEARLY IMPOSSIBLE TO REMOVE. THIS PROCESS OCCURS OVER TIME AND IS
DETERMINED BY THE INSTALLATION ENVIRONMENT.

INSTRUCTIONS PERTAINING TO

A RISK OF FIRE, OR INJURY TO

PERSONS IMPORTANT SAFETY

INSTRUCTIONS

Lighted fixture is HOT!
WARNING - To reduce the risk of
FIRE OR INJURY TO PERSONS:

Turn off/unplug and allow to cool before replacing LED.
Fixture gets HOT quickly! Contact only switch/plug when
turning on. Do not touch hot lens, guard, or enclosure.
Keep fixture away from materials that may burn.
Do not operate the luminaire fitting with a missing or
damaged shield. Do not touch the source at any time. Use

a soft cloth or gloves. Oil from skin may cause damage.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY

AND INSTALLATION INSTRUCTIONS

• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local and
Provincial Codes.

• Follow product label information and instructions.

• Qualified Personnel with appropriate personal protective
equipment must perform all servicing of this product.

• Before wiring to power supply and during servicing, turn off and
lock out power at fuse or circuit breaker before service.

• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause an
unsafe condition and void product warranty.

• Do not block light emanating from product in whole or part, as
this may cause an unsafe condition.

• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.

• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body.

• Replace LED assembly only with correct wattage and type of
power supply appropriate for LED assembly.

• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.

Hand Hole Installation Instructions

Spacers

Shade

Lens

Solid State BPM
(Beacon Pole Mount)

IMPORTANT LISTINGS AND CERTIFICATIONS

· Suitable for wet locations

Cap

Base

Rings

3-1/2” O.D. Pole or Pole with

3-1/2” O.D Tenon with Hand
Hole (Specify Separately)

(Pole By Others)

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS

40429 Brickyard Drive • Madera, CA 93636 • USA

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF TEKA ILLUMINATION AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF TEKA ILLUMINATION AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF TEKA ILLUMINATION IS STRICTLY FORBIDDEN.

DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF TEKA ILLUMINATION IS STRICTLY FORBIDDEN.

www.tekaillumination.com • [e-mail]

559.438.5800 • FAX [phone]

DATE

5-14-18

REFERENCE NUMBER

INS-2569-02

Phase 1 - Install Pole

1. Install pole (By Others) with 3”x5” min. hand hole
according to lighting plan and manufacturer’s
installation instructions. Install conduit (By
Others) to be used with this product.

2. Pull wiring necessary for installation (By Others.)

Leave sufficient wire length in the pole for

future service.

Phase 2 - Fixture Installation (Hand Hole Option)

BEACON POLE MOUNT™ (BPM)

Hand Hole Installation Instructions

DIM +

DIM -

Red

1. Thread fixture leads down pole to splice location
at hand hole.

2. Slide fixture over pole top. Secure with four (4)
1/4”-20 set screws using 3/16” Allen wrench.
Make sure the fixture is completely seated. Do not
overtighten.

3. Open hand hole as per pole manufacturer’s
instructions, then pull primary branch circuit
wiring through conduit to splice location and
pull down fixture leads from installed pole top.

LINE

COM

GROUND

WIRING DIAGRAM

4. Make watertight connections from primary
branch circuit to driver leads using waterproof
wire connectors (By Others). Connect green
ground wire to ground wiring from driver.
Connect incoming dimming controls to driver
primary side dimming controls. Connect
secondary side of driver to fixture leads. See

wiring diagram.

Driver

FIXTURE

Black

5. Place connections and driver on bracket into
pole through hand hole. (For use with 3”x5” hand
hole).

6. Driver bracket should hang off small horizontal
interior bar inside pole near hand hole. Use two
hooks on bracket to hang on interior bar.

7. Close hand hole cover with hardware and tools
as per pole manufacturer. (Pole and Hardware
By Others)

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

40429 Brickyard Drive • Madera, CA 93636 • USA

www.tekaillumination.com • [e-mail]

559.438.5800 • FAX [phone]

DATE

5-14-18

REFERENCE NUMBER

INS-2569-02

BEACON POLE MOUNT™ (BPM)

LED Replacement Installation Instructions

Replacing Optic and LED Module

1. Loosen three (3) captive #10-24 screws on cap
with 5/32” Allen wrench.

NEEDED

INSTALLATION:

By Others

2. Loosen three (3) #4-40 screws with 3/32” Allen
wrench that hold heatsink to fixture body.

FOR

5/32”, 3/32” & 1/16” Allen Wrench

Waterproof Wire Connectors

Gloves

3. Detach heatsink from fixture body via quick
disconnect. Carefully pull away and turn upside
down to access LED.

Do not pull on connector or wiring. Handle

with care.

4. Loosen three (3) #6-32 set screws on side of
dome lens optic holder using 1/16” Allen wrench.
Gently remove dome lens and optic holder.

7. Use small pick tool to push connector off LED

board through two small slots behind connector.
Once loose, lift connector upwards and off board.

Fragile! Do not pull on connector or wiring.

Handle with care.

5. Loosen two (2) #4-40 screws with 1/16” Allen
wrench.

8. Spread thin, even layer of thermal paste on back
of new LED module. Place new LED module onto
heatsink, lining up module with holes for screws.
Tighten two (2) #4-40 screws using 1/16” Allen
wrench to secure LED module to heatsink.

6. Carefully remove LED module from heatsink.

Do not pull on connector or wiring. Handle

with care.

9. Press connector straight downwards into slot
on module to snap into place.

Connector will only fit in one direction.

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

40429 Brickyard Drive • Madera, CA 93636 • USA

www.tekaillumination.com • [e-mail]

559.438.5800 • FAX [phone]

DATE

5-14-18

REFERENCE NUMBER

INS-2569-03

BEACON POLE MOUNT™ (BPM)

Relamping Instructions

10. Place dome lens into optic holder. Tighten three
(3) #6-32 set screws on side of dome lens optic
holder using 1/16” Allen wrench.

13. Attach cap with securing three (3) #10-24
screws using 5/32” Allen wrench.

11. Attach heatsink to fixture body via quick
disconnect. Line up on spacers.

12. Tighten three (3) #4-40 screws with 3/32” Allen
wrench to secure heatsink to fixture body.

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

40429 Brickyard Drive • Madera, CA 93636 • USA

www.tekaillumination.com • [e-mail]

559.438.5800 • FAX [phone]

DATE

5-14-18

REFERENCE NUMBER

INS-2569-03