TEFAL IS6200CGS, IS6200Z1, IS6300D1, IS6300D2, IS6300M1 Instruction Manual

...

1800125996 - 14/12

1800125996 IS6200 Z1_110X154 25/05/12 11:39 Page1

www.tefal.com

IS6200

1800125996 IS6200 Z1_110X154 25/05/12 11:39 Page2

18c

18b

18a

1800125996 IS6200 Z1_110X154 25/05/12 11:39 Page3

fig. 1 fig. 2 fig. 3

fig. 4 fig. 5 fig. 6a

fig. 6b fig. 7 fig. 8

“CLIC”

1800125996 IS6200 Z1_110X154 25/05/12 11:39 Page4

fig. 9 fig. 10 fig. 11

fig. 12 fig. 13 fig. 14

fig. 15 fig. 16a fig. 16b

1800125996 IS6200 Z1_110X154 25/05/12 11:39 Page5

1800125996 IS6200 Z1_110X154 25/05/12 11:39 Page6

SAFETY INSTRUCTIONS

PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE FIRST USE

AND KEEP THEM IN A SAFE PLACE.

-This product has been designed for domestic use only. Any commercial use, inappropriate use or failure to comply with the instructions, the manufacturer accepts no responsibility and the guarantee will not apply.

-For your safety, this appliance conforms to the applicable standards and regulations (Low Voltage, Electomagnetic Compatibility,Environmental Directives, as applicable...).

-Your product is an electrical appliance: it must be used in normal conditions of use.

-Always plug in your appliance into:

- An electrical installation with voltage between 220V and 240V.

- An earthed socket. If you are using a mains extension lead, ensure that it is correctly rated (16A) with an earth, and is fully extended.

- Connecting to the wrong voltage may cause irreparable damage to the appliance and will invalidate your guarantee.

- When using the appliance, one should pay attention to the steam emission. To reduce the risk of contact with hot water emitting from steam vents, check appliance before each use by holding it away from body and operating steam button.

- To reduce the risk of electric shock, do not immerse the appliance in water or other liquids.

- Appliance should always be turned «OFF» before plugging or unplugging from outlet. Never pull the cord to disconnect it from the outlet, instead grasp the plug and pull to disconnect.

- Do not allow the cord to touch hot surfaces. Let appliance cool completely before storing away. Loop cord loosely around appliance when storing.

- Do not direct steam at people or animals, or use steamer on garments while they are being worn.

- Always disconnect appliance from electrical outlet when filling with water, emptying, cleaning or when not in use.

- Should the power cord or the steam hose become damaged, it must be replaced by a TEFAL approved service centre to avoid the risk of danger or injury. Do not disassemble or attempt to repair the appliance.

- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

- Children should be supervised to ensure that they do not play with the appliance.

- Burns could occur from touching hot metal parts, hot water or steam. Use care when you empty a steam appliance, there may be hot water in the tank or inside the appliance.

- Fill water in water tank only and remove the water tank only when it is empty.

- Never drop or insert any object into any opening or hose.

- Always keep the hose and nozzle elevated above the water tank.

- Steam only in an up and down vertical motion. Never use steamer in a horizontal position or tilt into a backward position, this may result in hot water discharge.

- Do not place the steam nozzle directly on any surface or the appliance power cord while it is hot or plugged in. Use the stand provided.

- Use caution when changing attachments, as they may contain hot water from condensation. Ensure the attachments are cooled off to avoid contact with hot water.

- The use of accessory attachments other than those provided by Tefal is not recommended and may result in fire, electric shock or personal injury.

- This unit is for indoor use only.

1800125996 IS6200 Z1_110X154 25/05/12 11:39 Page1

- Do not cut or attempt to extend the steaming hose.

- To prevent the appliance over heating, when you hang clothes on garment hook for removing crease, please assemble the attached garment telescopic pole and extend it to its highest position.

Environmental protection first !

 Your appliance contains valuable materials which can be re-

covered or recycled.

 When disposing of it, take it to a local civic waste collection point.

DESCRIPTION

GARMENT STEAMER ASSEMBLY

Telescopic pole and hanger assembly

1. Unscrew the pole's fastening screw on the base of the pole. (fig. 1)

2. Hold the pole such that the cord holder is on the left. Check that the 2 pole clips are un-

locked. (fig. 2)

3. Insert the pole into the base by pressing downwards until the holes of the pole and

base are at the same level, so that you can put the screw back. If the holes are not aligned, check that the clips of the pole are well and truly unlocked. (fig. 3)

4. Screw the pole fastening screw back in as far as it will go so that the pole is firmly fixed

to the base. (fig. 4)

5. Push the hanger on the top of the pole vertically until you hear a click. (fig. 5)

6. Adjust the pole to its maximum height by sliding it upwards then locking the 2 clips.

(fig. 6a, 6b)

7. Install the steam head between the hanger hooks.

Filling the water tank

• Ensure that the steamer is unplugged. Remove the water tank from the base of the appliance by pulling the handle upwards (fig. 7). Unscrew the tank cap and fill the tank. (fig.

8). Maximum capacity is indicated by the “max” mark.

• The steamer must be used with TAP WATER. If the water in your area is hard, we recommends that you mix half tap water and half distilled water, which reduces the hardnes. You can also use bottled spring water.

IMPORTANT: Never use water that contains additives (starch, perfume, aromatic substances, softener, etc) in the steamer. Additives such as these can affect the properties of the steam and lead to the formation of deposits.

1. Steam head

2. Steam head hook

3. Built in hanger

4. Trouser/dress clips

5. Hanger holder

6. Pole locking clips

7. Electric cord holder

8. Electric cord

9. Velcro strip

10. Telescopic pole

11. Pole fastening screw

12. Steam hose connector

13. Removable water tank

14. ON/OFF pedal

15. Transport wheels

16. Textile steam hose

17. On/ off light

18. Built in accessories a. Fabric brush b. Crease attachment c. Lint pad

1800125996 IS6200 Z1_110X154 25/05/12 11:39 Page2

• After closing the cap, turn the tank down and hold it by the handle. Check out that no water is leaking through the cap.

• Place the water tank on the base (fig. 9).

USE

• Only operate the steamer on the floor clear of any materials which may obstruct the base of the steamer (flat and horizontal surface). Do not obstruct the openings on the lower part of the appliance. This appliance should not be used on very thick carpets or rugs.

• Undo the Velcro strip and completely unwind the electrical cord. (fig.10)

• Plug in to power socket. (fig.11)

• Switch on by pressing the pedal located at the front of the appliance. The power indicator light will come on. (fig.12)

• The appliance will begin producing steam after approximately 60 seconds.

• Hang the garments from the built-in hanger or from another hanger which may be suspended from the hook located on the hanger rod. To steam trousers, we recommend that you also use the support with clips as indicated in the illustration. (fig.14)

• Grasp the steam head with the steam vents pointing away from you.

• Start steaming by brushing material lightly with the grain of the fabric in an up/down vertical motion. The fabric brush opens the weave of the fabrics for better steam penetration.

• Start at the top the garment and gradually move downward (fig.13). Always steam in a vertical position.

• For more ease, we recommend to pull the garment downward with your free hand while steaming. Be careful not to touch the hot steam.

• During use, the hose may make a gurgling noise. This is a normal occurrence due to condensation. If the appliance begins to gurgle, rest the steam head on its support for a few moments in order to direct the condensation into the appliance once again.

ACCESSORIES

Before using an accessory, check the manufacturer recommendations. It is also recommend that you carry out a test on part of the fabric which cannot be seen.

Fabric brush

The fabric brush opens the weave of the fabrics for better steam penetration.

• Attach the fabric brush to the steam head by lining up the bottom of the brush with the bottom of the steam head. Gently push the top of the brush onto the steam head until it clicks into place.

• Gently brush the area to be steamed with the grain or nap of the fabric.

• Remove the fabric brush once unit is unplugged and completely cool. Remove it by pressing on the release tab on top of brush while pulling it forward.

Warning: Never steam a garment while it is being worn. The flexible pipe and the end of the steam head can become extremely hot during use. This is perfectly normal. Be careful and avoid any prolonged contact.

Be sure unit is unplugged and completely cool before attaching accesories.

1800125996 IS6200 Z1_110X154 25/05/12 11:39 Page3

+ 21 hidden pages