PL-606
FM stereo / SW / MW / LW DSP RECEIVER
OPERATION MANUAL
CONTROL LOCATIONS
1. Power
2. Band* & ATS
3. VM & SCAN
4. VF & SCAN
5. ETM (Easy Tuning Mode)
6. Delete
7. Memory
8. Display & Lock & Snooze
9. FM ST. & AM BW
10. Alarm
11. Time
12. FM & SW Telescopic Antenna
13. FM & SW Antenna Jack
14. Earphone Jack
15. USB 5V DC-Jack
16. Multifunctional Tuning Knob
17. Stand
18. Volume Knob
19. Battery Compartment
*本机出厂前已关闭 LW (长波)波段，若要开启 LW 波段，在关机状态下，长按[MW]键即可，
详见第 xx 页。
LCD DISPLAY
1．Battery consumption indicator / Charging indicator
2．Sleep timer indicator
3．Alarm on/off indicator
4．Key-lock indicator
5．Temperature (Temp.)
6．Signal indicators
dBu: signal strength unit
dB : Signal to Noise Ratio (S/N) unit
7．Alarm time indicator
8．SW meter band indicator
9．ETM indicator
10．Tuning speed:
" > " Slow Tuning
" >> " Fast Tuning
11．kHz: frequency unit for MW, LW & SW
MHz: frequency unit for FM
12．Digital number display (4 Digits)
With radio off: world time, alarm time, temperature
With radio on: word time, signal strength / SNR, alarm time, temperature, local time,
memory address, meter band.
13．Preset memory address
14．Digital number display
With radio off: local time
With radio on: frequency display, band display
15．Band indicator
16．FM stereo status indicator
17．Rechargeable batteries indicator
HOW TO TURN ON/OFF THE RADIO
1. Open the battery compartment located on the back of the unit, install 2x AA alkaline
batteries observing the battery polarity diagram on the back of the radio. Close the
battery door.
Installing batteries
2. Press the [POWER] button to turn on/off the radio.
Note:
If the radio is unable to be turned on. Please check if the batteries were installed correctly,
battery capacity is sufficient or the lock function had been applied with "
on screen (press & hold the [ ] button to unlock.)
" displays
TUNE IN STATIONS
Press the [POWER] button to turn on your radio, then select your desired band by
pressing the [FM], [MW]、 SW[ ] or [ ] button. In case of receiving FM/ SW
broadcasting, fully extend the telescopic antenna for a better reception. When receiving
MW(LW) broadcasting, please rotate the radio or change it's location to achieve optimum
reception. You can rotate the [VOLUME] knob to adjust to appropriate volume from 0 to 30
levels.
Now, you can turn into your favorite stations with any of the below tuning methods:
METHOD 1: ETM (EASY TUNING MODE)
ETM is the unique tuning method designed by Tecsun. It skillfully combines the reception
circuitry & control procedure to pre-select the suspected radio station and temporarily auto
stores them into the ETM memory (not the regular 550 memories). This highly enhances
the efficiency when tuning into radio stations. Employing ETM to tune preferred
frequencies. you can easily tune into your desired stations from those preferred
frequencies.
1. Press the [ETM] button with [ETM] shows on screen to
enter Easy Tuning Mode.
2. Press & hold the [ETM] button until the frequency start
running to auto scan and store stations into ETM memory,
within the present band.
3. When the frequency stop running, turn around the
[TUNING] knob to select those stored stations.
Notes: While operating ETM to search for stations, a few stations might be missed if
there is interference in the surrounding. In this case, you can simply key-in the frequency,
then press the [ETM] button to manually store it into ETM memory.
Tips:
FM station: When you are in a different city or country, you should perform the ETM
function again in stead of using ATS function, because this will not delete any of the
stations already stored within the memory.
MW station: It is recommendable to perform the ETM function during night time, because
there are usually many stations starting broadcasting at night.
SW station: It is recommendable to perform the ETM function in the morning, afternoon
as well as night time, because the transmitting signal of SW is very unstable and usually
there are more stations that start broadcasting in the late afternoon.
METHOD 2: MANUAL TUNING
Frequency searching: Press the [VF] button to switch into frequency mode, and
then rotate the [TUNING] knob to select your desired station.
FAST/SLOW tuning is shown in the chart below for each band.
Step
Band
FM 0.01MHz
MW 1kHz
LW 1k Hz
SW 1kHz 5kHz
Memory searching: Press the [VM] button to switch into memory mode, and then rotate
the [TUNING] knob to select those stored stations.
Slow tuning mode
Turning step
Fast tuning mode
Turning step
0.1MHz
9/10kHz
9kHz
METHOD 3: AUTO BROWSE STATION
1.Turn on the radio and press the [VF] button to switch into
frequency mode.
Loading...