Tecsun PL-365 Operation Manual

TECSUN

OPERATION MANUAL

PL-365

FM stereo / MW / SW-SSB DSP RECEIVER

PL-365

FM STEREO/ MW/ SW-SSBDSP RECEIVER

TECSUN

SLEEP

TECSUN ELECTRONIC IND. LTD.

RADIOS AUSTRALIA

TECSUN

24/9 Powells Road, Brookvale, NSW 2100 Australia

Ph: [phone]

Email: [e-mail]

www.tecsunradios.com.au

TECSUN RADIOS AUSTRALIA

TECSUN RADIOS AUSTRALIA

24/9 Powells Road, Brookvale, NSW 2100 Australia

Ph: [phone]

Email: [e-mail]

www.tecsunradios.com.au

SPECIFICATIONS

PL-365 Functional Block Diagram

PL-365 is equipped with DSP si4735 microchips (from Silicon
Labs in the USA) for digital demodulation of analog AM/FM
broadcasting signals, which greatly enhances the radio's
sensitivity, selectivity, S/N ratio and anti-interference.

AMPLIFIERCONTROLLER

CONTROL

INTERFACE

SW LPF

FM ANT

MW/LW

ANT

PL-365

Functional Block Diagram

1. Frequency range

FM 87~108 MHz

Japan 76~108 MHz

EU, USA 87.5~108 MHz

MW 522~1620 (150~1620) kHz

USA 520~1710 kHz

SW 1711~29999 kHz

2. Sensitivity

F M (S/N=30dB) Less than 3μV

MW (S/N=26dB) Less than 1mV/m

LW (S/N=26dB) Less than 10mV/m

SW (S/N=26dB) Less than 30μV

SSB (S/N=10dB) Less than 3μV

3.Selectivity

FM ＞60 dB

MW ＞60 dB

LW ＞60 dB

SW ＞60 dB

4. FM Stereo crosstalk Less than 25 dB

5. Memory 550

6. Output 350 mW

7. Power UM3 or AA X 3

USB 5V DC

8. Speaker Φ40mm, 500mW/16 Ohm

9. Earphone Jack Φ3.5mm, 8~32 Ohm, Stereo type

10. Dimensions Approx. 53(W) X 159(H) X 26(D) mm

11. Weight 128g (Batteries not included)

Ph: [phone]

www.tecsunradios.com.au

Ph: [phone]

www.tecsunradios.com.au

TECSUN RADIOS AUSTRALIA

24/9 Powells Road, Brookvale, NSW 2100 Australia

Ph: [phone]

Email: [e-mail]

www.tecsunradios.com.au

1

TABLE OF CONTENTS

CONTROL LOCATIONS................................................... 2

LCD DISPLAY.....................................................................4

TURN ON / OFF THE RADIO ............................................5

TUNE INTO STATIONS... ...................................................6

●

ETM (Easy Tuning Mode)

●

Manual tuning

●

Auto scan stations

............................................... 8

WORKING WITH MEMORIES............................................9

●

ATS - Auto Tuning Storage

●

Storing stations manually

●

Semi-Auto station storage

DELETE MEMORY...........................................................10

●

Delete Single Memory Manually

●

Semi auto-delete memory

●

Delete all memory

SLEEP FUNCTION...........................................................11

CLOCK SETTING.............................................................12

SETTING THE ALARM TIME...........................................12

...................................................13

................................................................13

.....................................................13

.......................................13

............................................................14

USING THE EXTERNAL ANTENNA................................16

......17

IMPORTANT MATTERS FOR USING BATTERIES.........18

TROUBLE SHOOTING.....................................................19

.............................................................21

SINGLE SIDE BAND (SSB)

SPECIFICATIONS

TURN OFF THE ALARM

DISPLAY MODE

KEY LOCK FUNCTION

FM ST. (FM STEREO) BUTTON

SYSTEM SETTING

USING THE INTELLIGENT CHARGING FUNCTION

TECSUN RADIOS AUSTRALIA

24/9 Powells Road, Brookvale, NSW 2100 Australia

Ph: [phone]

Email: [e-mail]

www.tecsunradios.com.au

CONTROL LOCATIONS

2

TROUBLE SHOOTING

QUESTIONS ANSWERS SOLUTIONS

Cannot turn on
the radio.

Radio turns off
while listening.

During ATS, some
stations cannot
be stored.
Some stored
stations have
noise.

Only few FM
stations can be
received.

Poor AM
reception in USA.

1

TECSUN

SLEEP

2

3

4

6

17

18

19

5

8

7

9

10

11

12

13

14

15

16

PL-365

FM STEREO/ MW/ SW-SSB DSP RECEIVER

9/10k

POWERTIME

ALARM

STEP

MEM. FM

MW

SW

ATS

DISPLAY

SCAN

VF/ VM

BFO

ETM

DEL.

USB/ LSB

FM ST.

Ph: [phone]

www.tecsunradios.com.au

Ph: [phone]

www.tecsunradios.com.au

TECSUN RADIOS AUSTRALIA

24/9 Powells Road, Brookvale, NSW 2100 Australia

Ph: [phone]

Email: [e-mail]

www.tecsunradios.com.au

19

18

Earphone jack

MW Antenna Jack

17

16

15

TIME Setting

Lock / Display button

12

Memory button (Storing radio stations) /
Batteries type selector

11

USB / LSB button

10

9

ETM (Easy Tuning Mode) button

8

VF/VM (View Frequency/View Memory) &
Scan button (Memory)

7

BFO / Fine tuning step set / FM ST. button

Battery compartment

6

USB 5V DC-IN jack

5

4

Volume knob

Band selector and Auto Tuning Storage

3

2

Multifunctional tuning knob

1

Power on/off

14

ALARM On/Off & Setting

DEL ETE & 9/10kHz MW step set button

13

3

FM & SW telescopic antenna

Removable Belt Clip

TECSUN RADIOS AUSTRALIA

24/9 Powells Road, Brookvale, NSW 2100 Australia

Ph: [phone]

Email: [e-mail]

www.tecsunradios.com.au

4

LCD DISPLAY

Battery consumption indicator /
Charging indicator

1

2

Sleep timer indicator

3

Alarm on/off indicator

6

Signal indicators
dBu: signal strength unit
dB : Signal to Noise Ratio
(S/N) unit

7

8

SW meter band indicator

9

ETM indicator

4

Temperature (Temp.)

5

10

11

kHz: frequency unit for
MW& SW
MHz: frequency unit for FM

15

Key-lock indicator

12

14

Digital number display
With radio off: local time
With radio on: frequency display,
band display

FM stereo status indicator

16

Band indicator

Alarm time indicator

Preset memory address

13

Rechargeable batteries indicator

1

2 3 4

5

6

7

8

9

10

14

15

16

13

SLEEP

Temp.

12 11

USING THE INTELLIGENT CHARGING FUNCTION

Connect USB 5V to external
power sources

In power off mode, install 3 x UM3 (AA size) rechargeable
(Ni-MH) batteries. Press & hold the [ ] button until
“ " and the "Ni-MH Battery" symbol appear on the
display.

1. Use any 5V external adaptor with USB plug to connect
this radio, the symbol " " will advance from the bottom
to top during power charging. It stops when batteries are
fully charged.

2. You can also use any USB cable
to connect the radio with your PC
for charging.

Notes for charging power:

Do not mix new and used batteries, or batteries of different
charging capacity.

Caution: Do not attempt to charge non-rechargeable
batteries, this will damage both the device and the batteries.

Digital number display (4 Digits)
With radio off: local time, alarm
time, temperature
With radio on: local time, signal
strength / SNR, alarm time,
temperature, memory address,
meter band, SSB fine tuning
frequency.

Ph: [phone]

www.tecsunradios.com.au

Ph: [phone]

www.tecsunradios.com.au

TECSUN RADIOS AUSTRALIA

24/9 Powells Road, Brookvale, NSW 2100 Australia

Ph: [phone]

Email: [e-mail]

www.tecsunradios.com.au

5

2. Short press on [POWER] button to turn the radio on or off.

TURN ON / OFF THE RADIO

1. Installing batteries
The battery compartment is located on the back of the
PL-365. To remove the battery compartment cover, apply
thumb pressure and slide it towards the bottom of the
radio. Install 3 AA size batteries into the battery
compartment, observing the battery polarity diagram on
the back of the radio. Display screen would show battery
capacity, time, etc.

Note:

If the radio is not able to be turned on. Please check if the
batteries were installed correctly, battery capacity is
sufficient or the lock function had been applied with symbol
" " displayed on screen.

Temp.

Short press

TECSUN RADIOS AUSTRALIA

24/9 Powells Road, Brookvale, NSW 2100 Australia

Ph: [phone]

Email: [e-mail]

www.tecsunradios.com.au

Turn ON/OFF charging function & exchange battery
consumption display

Press & hold the [ ] key with " " & " "
shows up to activate the consumption display of
rechargeable batteries and the built-in charging system.
Press & hold the [ ] key with " " shows up &
" " disappear to activate the consumption display of
alkaline batteries and turn off the built-in charging function.

Note: This radio is default to use alkaline batteries for
power supply. In case of using rechargeable batteries, you
should switch the radio in rechargeable batteries mode in
order to show the correct power capacity.

SLEEP

flashing

TUNE INTO STATIONS

6

Short press [POWER] button to turn on your radio, then
select your desired band by short pressing the [FM], [MW],
SW [ ] or [ ] button. In case of receiving FM/SW
broadcasting, fully extend the telescopic antenna for a
better reception.
Now, you can tune into your favorite station with any of the
below tuning methods:

Method 1: ETM (Easy Tuning Mode)
The ETM function allows you to tune into stations easily

and temporally store them into the ETM storage; 100
stations for FM/MW & 250 stations for SW.

Note: Scanned stations will not be stored in the regular
450 memories, but will remain in the ETM temporary storage
until next ETM scanning within each band.

HOW TO USE ETM

1. Turn on the radio and select
your desired band by pressing
either the FM, MW or SW
[ ] or [ ] button.

2. Short press the [ETM] button to
enter Easy Tuning Mode.

3. Long press the [ETM] button to
automatically scan all available
stations within the selected band.

4. When the scanning procedure is
completed, turn the [TUNING]
knob to browse through the found
stations.

5. Short press the [VF/VM] button to
exit the ETM mode.

Station

Notes:

FM station: When you are in a different city or country, you
should perform the ETM function again, because this will
not delete any of the stations already within the memory.

Frequency
running

Set the fine tuning step

Turn off the radio,
the current fine tuning step, turn the [TUNING] knob to
adjust.

- " " indicates that the fine
tuning step of SSB is 50Hz.

- " " indicates that the fine
tuning step of SSB is 20Hz.

- " " indicates that the fine
tuning step of SSB is 10Hz.

Ph: [phone]

www.tecsunradios.com.au

Ph: [phone]

www.tecsunradios.com.au

TECSUN RADIOS AUSTRALIA

24/9 Powells Road, Brookvale, NSW 2100 Australia

Ph: [phone]

Email: [e-mail]

www.tecsunradios.com.au

flashing

Auto-scan with pre-listening

Frequency
running

7

Method 3: AUTO-SCAN STATIONS

1. Turn on the radio and short
press the [VF/VM] button with
the frequency flashing.

2. Long press the [VF/VM] button
to scan from one station to
another, staying on each
stations for about 5 seconds.

3. To stop auto browse function,
simply press the [VF/VM] button.

MW station: It is recommended to perform the ETM
function during day time as well as night time, because
there usually are more stations that start broadcasting at
night

SW station: It is recommended to perform the ETM
function in the morning, afternoon as well as night time,
because the transmitting signal of SW is very unstable and
there usually are more stations that start broadcasting in
the late afternoon.

Method 2: MANUAL TUNING
Turn on the radio, short press the [VF/VM] button to switch

into frequency mode. Rotate the [TUNING] knob to select
your station.

FAST/SLOW tuning is shown in the chart below for each band.

0.01 MHz
1kHz

1 kHz

0.1 MHz

9 /10kHz

5 kHz

FM
MW

SW

step

band

turning step

Slow tuning mode

Fast tuning mode

turning step

Note: While pre-listening a station, press the [MEM.]
button to store it.

SLEEP

TECSUN RADIOS AUSTRALIA

24/9 Powells Road, Brookvale, NSW 2100 Australia

Ph: [phone]

Email: [e-mail]

www.tecsunradios.com.au

When the radio is turned on by the alarm function with radio,
you can short press [POWER] button to continue listening
radio afterwards.
Short press [POWER] again to turn off the radio.

TURN OFF THE ALARM

In radio off mode, short press the [DISPLAY] button to
view the temperature or alarm time.

In radio on mode, short press the [DISPLAY] button to
view the alarm time, temperature, local time, signal
strength/SNR.

DISPLAY MODE

To activate the key lock function, press & hold the [ ]
button; the " " symbol appears on the display. Press &
hold the [ ] button again to unlock.

KEY LOCK FUNCTION

When listening to FM stations via earphones, press the
[FM. ST] button; if the station is transmitted in stereo the
" " symbol appears on the left side of the display.

FM ST. (FM STEREO) BUTTON

8

Method 4: AUTO BROWSE MEMORY

1. Turn on the radio to enter memory
mode. Short press the [VF/VM]
button until the memory position
flashes in the upper right corner
and disappears after 3 seconds.

2. Long press the [VF/VM] button
until "Preset" flashes. The
memory is now being browsed,
staying on each stored station for
about 3 seconds.

3. To stop browsing, press the
[VF/VM] button.

Note: Please read the "Working with Memories" section
before using this function.

flashing

Auto-scan memory with
pre-listening

SLEEP

( )

SINGLE SIDE BAND SSB

1. In any mode, press the [USB/LSB]
button to select SSB reception;
press again to select USB/LSB.

2. Turn the [TUNING] knob to search
stored SSB stations.

3. Press the [BFO] button, when “U” /
“L” flashes on the display, turn the
[TUNING] knob to adjust the
reception.

- " " is for USB.

- " " is for LSB.

When it is off, press and hold the [BFO] button to set the
fine tuning step. (P.15)

Exit SSB: Press and hold the [USB/LSB] button to exit.

SLEEP

SSB fine tuning frequency

Ph: [phone]

www.tecsunradios.com.au

Ph: [phone]

www.tecsunradios.com.au

TECSUN RADIOS AUSTRALIA

24/9 Powells Road, Brookvale, NSW 2100 Australia

Ph: [phone]

Email: [e-mail]

www.tecsunradios.com.au

SLEEP

flashing

9

WORKING WITH MEMORIES

The PL-365 has 550 station memories: FM (100), MW (100),
SSB (100) and SW (250).

Method 1: ATS - Auto Tuning Storage

To automatically store all available
stations, first select the frequency
band in which to perform ATS.
Then press & hold the band button
(e.g. [FM] or [MW]); "PRESET" will
flash in the top right corner of the
display while the frequency starts
running. The frequency stops
running once the ATS operation
has completed. Rotate the [TUNING]
knob to browse all stored stations.

There are two modes for SW ATS function:
Mode A: In SW band, long press the [A / ] button to ATS
the stations within all meter bands.
Mode B: In SW band, long press the [B / ] button to ATS
the stations within present meter band only.

Note:

When performing ATS in FM, MW or SW (mode A), all
previously stored stations will be replaced.

When performing ATS in SW (mode B), previously stored
stations are not replaced; newly found stations are stored in
blank SW memory positions.

Auto Tuning Storage

TECSUN RADIOS AUSTRALIA

24/9 Powells Road, Brookvale, NSW 2100 Australia

Ph: [phone]

Email: [e-mail]

www.tecsunradios.com.au

SLEEP FUNCTION

Method 2: SEMI AUTO-DELETE MEMORY

Press the [VF/VM] button to enter the memory mode,
then press & hold the [VF/VM] button to activate the
memory auto-browse function. During the browsing
process unwanted stations can be deleted by pressing
the [DEL.] button. Press the [VF/VM] button again to
stop browsing.

10

Method 2: MANUALLY STORING STATION

1. Tune to your desired station, press the [MEM.] button
once and notice the PRESET number flashing in the

upper right corner of the display.

2. The station is automatically stored after 3 seconds;
press the [MEM.] button to confirm immediately. If you
prefer to store the station at a different memory position,
rotate the [TUNING] knob to the position of your choice
and press the [MEM.] button to confirm.

Method 3: SEMI-AUTO STATION STORAGE

1. Short press the [VF/VM] button to enter frequency
mode.

2. Long press [VF/VM] button to activate the Auto-browse
function.

3.

During the browsing process, press the [MEM.]
button to store stations into the next available
memory position. The browsing process continues
until you press the [VF/VM] again.

DELETE MEMORY

Method 1: DELETE SINGLE MEMORY MANUALLY

1. Turn the radio on and press the [VF/VM] button until
"Preset" and the memory position appears in the upper
right corner of the display.

2. Rotate the [TUNING] knob to select the stored station
you wish to delete.

3. Press & hold the [DEL.] button until " " flashes on
the display, press again to confirm.

Note: If " " is flashing more than 3 seconds without
confirmation, it will exit the delete function automatically.

1. In POWER OFF mode, press &
hold the [POWER] button untill
the sleep timer symbol “ ”
flashes on the display.

2. Rotate the [TUNING] knob
immediately to select a sleep
timer from 1 - 120 minutes or
select “ ” for POWER ON
mode (the radio will be turned
on after 1 second).

Note: The default setting of the sleep timer is “ ”.

DELETE ALL MEMORY

Press the [VF/VM] button to
enter the memory mode, then
press & hold the [DEL.] button
until " " appears on the
display, press the [DEL.] button
again to confirm.

Note: If the [DEL.] button is not pressed within 2 seconds
to confirm, the delete function is automatically exited.

Method 3:

Ph: [phone]

www.tecsunradios.com.au

Ph: [phone]

www.tecsunradios.com.au

TECSUN RADIOS AUSTRALIA

24/9 Powells Road, Brookvale, NSW 2100 Australia

Ph: [phone]

Email: [e-mail]

www.tecsunradios.com.au

SLEEP FUNCTION

11

Delete all memories

Method 2: SEMI AUTO-DELETE MEMORY

Press the [VF/VM] button to enter the memory mode,
then press & hold the [VF/VM] button to activate the
memory auto-browse function. During the browsing
process unwanted stations can be deleted by pressing
the [DEL.] button. Press the [VF/VM] button again to
stop browsing.

SLEEP

1. In POWER OFF mode, press &
hold the [POWER] button untill
the sleep timer symbol “ ”
flashes on the display.

2. Rotate the [TUNING] knob
immediately to select a sleep
timer from 1 - 120 minutes or
select “ ” for POWER ON
mode (the radio will be turned
on after 1 second).

Note: The default setting of the sleep timer is “ ”.

SLEEP

Sleep time range

SLEEP

flashing

flashing

DELETE ALL MEMORY

Press the [VF/VM] button to
enter the memory mode, then
press & hold the [DEL.] button
until " " appears on the
display, press the [DEL.] button
again to confirm.

Note: If the [DEL.] button is not pressed within 2 seconds
to confirm, the delete function is automatically exited.

Method 3:

TECSUN RADIOS AUSTRALIA

24/9 Powells Road, Brookvale, NSW 2100 Australia

Ph: [phone]

Email: [e-mail]

www.tecsunradios.com.au

12

SETTING THE CLOCK

1. Long press the [TIME] button until you see the hour
flashing. Rotate the [TUNING] knob to set the correct
hour, then short press the [TIME] button and notice the
minutes are flashing.

2. While it's flashing turn the [TUNING] knob to set the
correct minutes, then press [TIME].

SETTING THE ALARM TIME

1. Press & hold the [ALARM] button until both "HOUR" and
"AL" are flashing on the display; rotate the [TUNING]
knob to adjust the hours, then press the [ALARM] button
to adjust the minutes.

2. Rotate the [TUNING] knob to adjust the minutes and
press the [ALARM] button; the " " symbol flashes on
the display.

3. Rotate the [TUNING] knob to select the time
(1-90 minutes) after which the alarm should automatically
turn off.

4. Press the [ALARM] button to confirm; the alarm symbol
" " appears on the display.

5. To turn off the alarm, press the [ALARM] button until the
alarm symbol " " disappears.

SLEEP

Setting the alarm by radio

1. Turn on the radio and tune to your preferred radio station.
Please set the volume to a suitable alarm level.

2. Short press [MEM.] button and notice the PRESET
number flashing in the upper right corner of the display.

3. While flashing, press the [ALARM] button. The alarm
symbol " " briefly appears on the display. The alarm
station is now set.

WORKING WITH MEMORIES

The PL-365 has 550 station memories: FM (100), MW (100),
SSB (100) and SW (250).

Method 1: ATS - Auto Tuning Storage

To automatically store all available
stations, first select the frequency
band in which to perform ATS.
Then press & hold the band button
(e.g. [FM] or [MW]); "PRESET" will
flash in the top right corner of the
display while the frequency starts
running. The frequency stops
running once the ATS operation
has completed. Rotate the [TUNING]
knob to browse all stored stations.

There are two modes for SW ATS function:
Mode A: In SW band, long press the [A / ] button to ATS
the stations within all meter bands.
Mode B: In SW band, long press the [B / ] button to ATS
the stations within present meter band only.

Note:

When performing ATS in FM, MW or SW (mode A), all
previously stored stations will be replaced.

When performing ATS in SW (mode B), previously stored
stations are not replaced; newly found stations are stored in
blank SW memory positions.

Ph: [phone]

www.tecsunradios.com.au

Ph: [phone]

www.tecsunradios.com.au

TECSUN RADIOS AUSTRALIA

24/9 Powells Road, Brookvale, NSW 2100 Australia

Ph: [phone]

Email: [e-mail]

www.tecsunradios.com.au

13

When the radio is turned on by the alarm function with radio,
you can short press [POWER] button to continue listening
radio afterwards.
Short press [POWER] again to turn off the radio.

TURN OFF THE ALARM

In radio off mode, short press the [DISPLAY] button to
view the temperature or alarm time.

In radio on mode, short press the [DISPLAY] button to
view the alarm time, temperature, local time, signal
strength/SNR.

DISPLAY MODE

To activate the key lock function, press & hold the [ ]
button; the " " symbol appears on the display. Press &
hold the [ ] button again to unlock.

KEY LOCK FUNCTION

When listening to FM stations via earphones, press the
[FM. ST] button; if the station is transmitted in stereo the
" " symbol appears on the left side of the display.

FM ST. (FM STEREO) BUTTON

TECSUN RADIOS AUSTRALIA

24/9 Powells Road, Brookvale, NSW 2100 Australia

Ph: [phone]

Email: [e-mail]

www.tecsunradios.com.au

14

SYSTEM SETTING

Frequency range setting for FM

Press & hold the [FM] button until 76-108MHz, 87-108MHz
or 87.5-108MHz appears on the display. Press the [FM]
button to select a suitable frequency range for FM.

MW(AM) step setting

Turn off the radio, then long press the [9/10k] button until
"9 kHz" or "10 kHz" is displayed.
The temperature unit display is associated with the MW
tuning step. The temperature is shown in Celsius (C) when
the MW tuning is in 9 kHz steps. Tuning steps of 10 kHz
are associated with Fahrenheit (F).

Turn On/Off LW

LW is only available in 9 kHz tuning steps. Therefore,
before turning on LW, first assure the device is set to 9 kHz
tuning steps.
Then, long press the [MW] button and "MW 150 - 1620" is
displayed to confirm that LW has been turned on.

Method 3: AUTO-SCAN STATIONS

1. Turn on the radio and short
press the [VF/VM] button with
the frequency flashing.

2. Long press the [VF/VM] button
to scan from one station to
another, staying on each
stations for about 5 seconds.

3. To stop auto browse function,
simply press the [VF/VM] button.

MW station: It is recommended to perform the ETM
function during day time as well as night time, because
there usually are more stations that start broadcasting at
night

SW station: It is recommended to perform the ETM
function in the morning, afternoon as well as night time,
because the transmitting signal of SW is very unstable and
there usually are more stations that start broadcasting in
the late afternoon.

Method 2: MANUAL TUNING
Turn on the radio, short press the [VF/VM] button to switch

into frequency mode. Rotate the [TUNING] knob to select
your station.

FAST/SLOW tuning is shown in the chart below for each band.

0.01 MHz

FM
MW

SW

step

band

turning step

Slow tuning mode

Note: While pre-listening a station, press the [MEM.]
button to store it.

Ph: [phone]

www.tecsunradios.com.au

Ph: [phone]

www.tecsunradios.com.au

TECSUN RADIOS AUSTRALIA

24/9 Powells Road, Brookvale, NSW 2100 Australia

Ph: [phone]

Email: [e-mail]

www.tecsunradios.com.au

15

Turn ON/OFF charging function & exchange battery
consumption display

Press & hold the [ ] key with " " & " "
shows up to activate the consumption display of
rechargeable batteries and the built-in charging system.
Press & hold the [ ] key with " " shows up &
" " disappear to activate the consumption display of
alkaline batteries and turn off the built-in charging function.

Note: This radio is default to use alkaline batteries for
power supply. In case of using rechargeable batteries, you
should switch the radio in rechargeable batteries mode in
order to show the correct power capacity.

Set the fine tuning step

Turn off the radio,
the current fine tuning step, turn the [TUNING] knob to
adjust.

press and hold the [BFO] button to show

- " " indicates that the fine
tuning step of SSB is 50Hz.

- " " indicates that the fine
tuning step of SSB is 20Hz.

- " " indicates that the fine
tuning step of SSB is 10Hz.

fine tuning step

TECSUN RADIOS AUSTRALIA

24/9 Powells Road, Brookvale, NSW 2100 Australia

Ph: [phone]

Email: [e-mail]

www.tecsunradios.com.au

16

USING THE EXTERNAL ANTENNA

WINDOW WALL

Do not place the external antenna outdoors
during a thunderstorm!

EXTERNAL FM/SW ANTENNA

Enhancing FM/SW reception

Use the external wire antenna to clip onto the telescopic
antenna of the PL-365. Then position the opposite end
outside the window for better FM and SW reception.

PL-365

TECSUN

POWER

FM MW

SW

ATS

SLEEP

High Sensitivity AM Antenna

Enhancing AM/LW reception

Plug the AM/LW external antenna into the AM Antenna
jack, then rotate the antenna for better AM/LW reception.

2. Short press on [POWER] button to turn the radio on or off.

TURN ON / OFF THE RADIO

1. Installing batteries
The battery compartment is located on the back of the
PL-365. To remove the battery compartment cover, apply
thumb pressure and slide it towards the bottom of the
radio. Install 3 AA size batteries into the battery
compartment, observing the battery polarity diagram on
the back of the radio. Display screen would show battery
capacity, time, etc.

Note:

If the radio is not able to be turned on. Please check if the
batteries were installed correctly, battery capacity is
sufficient or the lock function had been applied with symbol
" " displayed on screen.

9/10k

TIME

ALARM

STEP

MEM.

DISPLAY

SCAN

VF/VM

BFO

ETM

DEL.

USB/LSB

FM ST.

FM STEREO/MW /SW-SSB DSP RECEIVER

Ph: [phone]

www.tecsunradios.com.au

Ph: [phone]

www.tecsunradios.com.au

TECSUN RADIOS AUSTRALIA

24/9 Powells Road, Brookvale, NSW 2100 Australia

Ph: [phone]

Email: [e-mail]

www.tecsunradios.com.au

17

USING THE INTELLIGENT CHARGING FUNCTION

Connect USB 5V to external
power sources

In power off mode, install 3 x UM3 (AA size) rechargeable
(Ni-MH) batteries. Press & hold the [ ] button until
“ " and the "Ni-MH Battery" symbol appear on the
display.

1. Use any 5V external adaptor with USB plug to connect
this radio, the symbol " " will advance from the bottom
to top during power charging. It stops when batteries are
fully charged.

2. You can also use any USB cable
to connect the radio with your PC
for charging.

Notes for charging power:

Do not mix new and used batteries, or batteries of different
charging capacity.

Caution: Do not attempt to charge non-rechargeable
batteries, this will damage both the device and the batteries.

TECSUN RADIOS AUSTRALIA

24/9 Powells Road, Brookvale, NSW 2100 Australia

Ph: [phone]

Email: [e-mail]

www.tecsunradios.com.au

19

18

Earphone jack

MW Antenna Jack

17

16

15

TIME Setting

Lock / Display button

12

Memory button (Storing radio stations) /
Batteries type selector

11

USB / LSB button

10

9

ETM (Easy Tuning Mode) button

8

VF/VM (View Frequency/View Memory) &
Scan button (Memory)

7

BFO / Fine tuning step set / FM ST. button

Battery compartment

6

USB 5V DC-IN jack

5

4

Volume knob

Band selector and Auto Tuning Storage

3

2

Multifunctional tuning knob

1

Power on/off

14

ALARM On/Off & Setting

DEL ETE & 9/10kHz MW step set button

13

FM & SW telescopic antenna

Removable Belt Clip

18

IMPORTANT MATTERS FOR USING BATTERIES

1. When the device is not powered by batteries or the
adaptor for a long time, the clock setting is lost, but the
stored radio stations are saved.

2. When battery power is low, the " " symbol starts
flashing to alert you to charge the batteries or change to
new ones. The device turns off automatically when all
power is gone.

3. Do not mix new and used batteries, this may damage
the radio and display an incorrect power capacity.

4. If not using the radio for an extended period of time,
remove the batteries to prevent liquid leakage and
damage to the device.

Ph: [phone]

www.tecsunradios.com.au

Ph: [phone]

www.tecsunradios.com.au

TECSUN RADIOS AUSTRALIA

24/9 Powells Road, Brookvale, NSW 2100 Australia

Ph: [phone]

Email: [e-mail]

www.tecsunradios.com.au

19

TROUBLE SHOOTING

QUESTIONS ANSWERS SOLUTIONS

Cannot turn on
the radio.

Radio turns off
while listening.

During ATS, some
stations cannot
be stored.
Some stored
stations have
noise.

Only few FM
stations can be
received.

Poor AM
reception in USA.

-Batteries have no
power.

-Didn't install the
batteries properly.

-Key lock function
is activated.

-Batteries have no
power.

-Sleep timer is
activated.

-Frequency of
stations is too
weak.

-There is
interference
near by your area.

-FM frequency may
have been set to
76 - 90MHz
accidentally.

-USA uses 10kHz
AM tuning steps,
the device may still
be set to 9kHz.

-Replace all batteries
with new ones.

-Take note of the
correct polarity
direction, then
reinstall the batteries.

-Press the [ ] button
to deactivate it.

-Replace or charge all
batteries.

-Turn on the radio
again.

-Search the station
manually.

-Contract the antenna
or move to other
location and try
again.

-Turn off the radio,
press & hold the
[FM SET] button to
select the accurate
FM frequency range.

-Turn off the radio
press the [9/10kHz]
button to select
accurate tuning step.

TECSUN RADIOS AUSTRALIA

24/9 Powells Road, Brookvale, NSW 2100 Australia

Ph: [phone]

Email: [e-mail]

www.tecsunradios.com.au

20

QUESTIONS ANSWERS SOLUTIONS

-Did not set the
proper radio station
for the alarm.

-Or there is no
broadcasting at that
frequency.

When the alarm
(radio) goes off,
there is only
noise in the
broadcasting.

-Preset your alarm
station properly
(see the above
setting).

-Make sure it is
possible to receive
radio broadcastings
at your location.

-Or set the alarm by
buzzer.

Radio malfunction.

There may be
some form of
interference,
causing the
microchip to not
function properly.

Remove the
batteries. Reinstall
the batteries once
the device's display
has turned off
completely. If it is still
not able to work,
please contact your
nearest dealer for
customer service.

TABLE OF CONTENTS

CONTROL LOCATIONS................................................... 2

LCD DISPLAY.....................................................................4

TURN ON / OFF THE RADIO ............................................5

TUNE INTO STATIONS... ...................................................6

●

ETM (Easy Tuning Mode)

●

Manual tuning

●

Auto scan stations

WORKING WITH MEMORIES............................................9

●

ATS - Auto Tuning Storage

●

Storing stations manually

●

Semi-Auto station storage

DELETE MEMORY...........................................................10

●

Delete Single Memory Manually

●

Semi auto-delete memory

●

Delete all memory

SLEEP FUNCTION...........................................................11

CLOCK SETTING.............................................................12

SETTING THE ALARM TIME...........................................12

USING THE EXTERNAL ANTENNA................................16

IMPORTANT MATTERS FOR USING BATTERIES.........18

TROUBLE SHOOTING.....................................................19

SINGLE SIDE BAND (SSB)

SPECIFICATIONS

TURN OFF THE ALARM

DISPLAY MODE

KEY LOCK FUNCTION

FM ST. (FM STEREO) BUTTON

SYSTEM SETTING

USING THE INTELLIGENT CHARGING FUNCTION

Ph: [phone]

www.tecsunradios.com.au

Ph: [phone]

www.tecsunradios.com.au

TECSUN RADIOS AUSTRALIA

24/9 Powells Road, Brookvale, NSW 2100 Australia

Ph: [phone]

Email: [e-mail]

www.tecsunradios.com.au

21

SPECIFICATIONS

1. Frequency range

FM 87~108 MHz

Japan 76~108 MHz

EU, USA 87.5~108 MHz

MW 522~1620 (150~1620) kHz

USA 520~1710 kHz

SW 171

1~29999 kHz

2. Sensitivity

F M (S/N=30dB) Less than 3μV

MW (S/N=26dB) Less than 1mV/m

LW (S/N=26dB) Less than 10mV/m

SW (S/N=26dB) Less than 30μV

SSB (S/N=10dB) Less than 3μV

3.Selectivity

FM ＞60 dB

MW ＞60 dB

LW ＞60 dB

SW ＞60 dB

4. FM Stereo crosstalk Less than 25 dB

5. Memory 550

6. Output 350 mW

7. Power UM3 or AA X 3

USB 5V DC

8. Speaker Φ40mm, 500mW/16 Ohm

9. Earphone Jack Φ3.5mm, 8~32 Ohm, Stereo type

10. Dimensions Approx. 53(W) X 159(H) X 26(D) mm

11. Weight 128g (Batteries not included)