TechniSat VC 2002 S User Manual

TechniSat
TUNING
CH
An/Aus M
AUDIO
MONO/ST
A/B
12
3
4
5
6
7
8
9
0
W/N
V/H
DEV.
DECODER
D.MODE
VC 2002 S
INSTALLATION AND OPERATION
Satellite Receiver TechniSat
®
VC 2002 S Stereo
TechniSat®Satellitenfernsehprodukte GmbH, TechnicPark, Postfach 560. W-5568 Daun, Germany
STAND BY
TechniSat
VC 2002 S
1019/J/92
TechniSat® VC 2002 S
2
INSTALLATION:
The procedures set out on page 5 should be fol­lowed carefully.
NOTE:
Always connect the LNB before connecting to the mains supply. Failure to do this may cause damage to the appliance.
Ventilation:
Vents on the top and side panels are provided for necessary ventilation. The appliance should not be placed in a position where the free pas­sage of air would be severely restricted. In addi­tion, for the same reasons as above, the VC 2002 S should not be placed on a soft base.
Water and moisture:
Ensure that the appliance does not come into contact with any dampness or moisture - RISK OF ELECTRIC SHOCK (and/or damage to the VC 2002 S).
Heat:
Do not install the VC 2002 S in the immediate proximity of a heat source (radiator, oven etc.).
CARE AND USE:
Power source:
Connect the VC 2002 S to a power supply which matches the requirements of the appliance (240 V/50 Hz).
Safe connection to the mains:
The mains leads should be routed so that they are not likely to be walked on or pinched by items placed against them.
When not in use:
If the VC 2002 S is left unattended or unused for long periods of time be sure to unplug the mains connector.
Unplug the VC 2002 S from the mains when:
- the mains lead or mains connector is damaged
- the VC 2002 S has been exposed to rain or water
- a solid object or liquid substance has entered the appliance via the air vents
- there is a noticeable change in the performance of the VC 2002 S, the appliance is not operating as normal
- the VC 2002 S has been dropped or the outer casing has been damaged
NOTE:
Servicing and repairs must only be carried out by trained service staff.
Accessories and replacement parts:
Both accessories and replacement parts should only be purchased as recommended by your satellite dealer. Be sure to consult your dealer in all aspects concerning equipment purchase, servicing and repairs.
Cleaning:
Disconnect the VC 2002 S from the mains befo­re cleaning. Use a damp cloth only . Do not use liquid or aerosol cleaners.
.
INSTRUCTION MANUAL FOR THE TECHNISA T VC 2002 S
SAFETY INSTRUCTIONS
In the interests of safety please read and observe the following instructions
before using your new VC 2002 S. This sheet and the following pages
concerning installation and operation should be retained for future reference.
TechniSat® VC 2002 S
3
CONTENTS Page
Safety Instructions 2
Appliance Description 4
Installation & Initial Operation 5
Preprogramming 7
Channel selection
Individual Programming 7
Polarisation Video Tuning DEV Selection Audio Tuning Storing
Erasing
Programming
Watching a scrambled V ideocrypt programme 8
Screen Messages Connecting a separate decoder Frequency Shift
Specifications 9
Trouble Shooting 10
Programme Table 1 (V/H LNB) 11 Programme Table 2 (ISISAT LNB) 12
BACK PANEL
TechniSat® VC 2002 S
*1Press this button if you wish to see a “Pay per View” programme.
4
STAND BY
TechniSat
VC 2002 S
APPLIANCE DESCRIPTION:
FRONT PANEL
AUTHORIZE BUTTON *
1
Digital Display
STANDBY LED
Channel Up/Down Keys
AUDIO OUTPUTS L/R
LNB IF IN
DECODER OUTPUT
VIDEO OUTPUT
SCART CONNECTION
FOR DECODER / VCR
SCART CONNECTION FOR TV
TSG / VIDEO SWITC
H
ANT IN
UHF
CHANNEL
ADJUSTMENT
(PRESET TO 36)
UHF OUT FUSE
MODULATOR SWITCH
PAL I / PAL G
Decoder Card Slot
EUROSCART FOR VCR/REC EUROSCART FOR TV
DECODER VIDEO
LNB PWR OUT
5,5 W MAX
PAL I
PAL B/G
TSG
VIDEO
CH
UHF OUT
ANT IN
30 WATTS
MAX
TechniSat® VC 2002 S
5
REMOTE CONTROL
TechniSat
TUNING
CH
An/Aus M
AUDIO
MONO/ST
A/B
STORE
ERASE
1 2
3
4
5
6
7
8
9
0
W/N
V/H
DEV.
DECODER
D.MODE
POWER ON/OFF
MUTE
AUDIO UP/DOWN (FOR SUBCARRIER
FREQUENCY 5.0 - 8.80 MHz)
MONO/STEREO
A/B: LEFT/RIGHT STEREO (USED WITH AUDIO UP/DOWN) DE-EMPHASIS (WIDE - TV-SOUND, NARROW - RADIO)
CHANNEL UP/DOWN
VIDEO FREQUENCY UP/DOWN (950-
2050 MHZ)
KEY PAD
STORE ERASE
DEVIATION HIGH/LOW BRIGHTNESS
V/H POLARISATION
DECODER (NORMAL/DECODER MODE) DECODER SIGNAL SELECTION (D1-D4)
1. Connect the receiver VC 2002 S to the LNB of the outdoor unit using a coaxial cable via IF-IN connection.
CAUTION: Always ensure that the mains supply is off when making any connections (including LNB connection).
2. The connection between receiver and TV is made using a scart cable. Alternatively, you can make the connection using an antenna cable.
3. Connect the receiver to the mains supply (240 V/50 Hz).
4. i) If you are using a scart cable connection, switch your TV to A V.
ii) If UHF cable connections are being used it is
necessary to find a suitable UHF channel. The satellite receiver is preprogrammed to channel
36. T o set the TV or VCR to this channel select TSG on the receiver back panel and search on the TV until two vertical white bars are clearly
visible. If due to interference it is necessary to adjust the UHF channel, this can be done using the channel adjustment switch on the back of the
receiver (by turning the screw).
INSTALLATION & INITIAL OPERATION
TechniSat®VC 2002 S
1) Connection to TV (+ external decoder if required)
2) Connection to TV + VCR
3) Connection to TV + VCR
6
Installation possibilities:
Decoder
SCART
DECODER
VIDEO
EUROSCART FOR VCR/REC EURO SCART FOR TV
LNB PWR OUT
5,5 W MAX
CH
UHF OUT
ANT IN
30 WATTS
MAX
UHF/VHF
EURO SCART
LNB
Receiver
Scart
DECODER
VIDEO
EUROSCART FOR VCR/REC EURO SCART FOR TV
LNB PWR OUT
5,5 W MAX
CH
UHF OUT
ANT IN
30 WATTS
MAX
UHF/VHF
EURO SCART
EUROSCART FOR VCR/REC
OUT IN
30 WATTS
MAX
VCR
LNB
Receiver
Scart
Scart
EURO SCART
EUROSCART FOR VCR/REC
DECODER
VIDEO
EUROSCART FOR VCR/REC EURO SCART FOR TV
LNB PWR OUT
5,5 W MAX
CH
UHF OUT
ANT IN
30 WATTS
MAX
UHF/VHF
EURO SCART
EUROSCART FOR VCR/REC
OUT IN
30 WATTS
MAX
VCR
LNB
Receiver
Scart
Scart
EURO SCART
EUROSCART FOR VCR/REC
TechniSat® VC 2002 S
7
PREPROGRAMMING
At the end of this manual you will find a list of all the preprogrammed TV and radio stations. This table also contains information on the stored audio/video parameters which will give you a guide if you wish to change the preset. If you are not satisfied with the preprogramming or if you want to add some channels, you can programme the receiver to your own require­ments as described in the section on “Individu­al Programming” (see below).
i) Using V/H LNB: The TechniSat VC 2002 S is preprogrammed in accordance with programme table 1 at the end of this manual.
ii) Using ISISA T LNB:
(refer to programme table 2)
If the ISISAST-Preprogramming is called up, the preprogramming for V/H LNBs does not meet the table any more, and all programmes for V/H-LNB need to be programmed again.
1. Switch the receiver to Standby mode (power off)
2. Press both the up and down channel buttons simultaneously for approx. 3 seconds. The display will indicate “SEL” (select).
3. You can now select a channel: Channel up = PRG 1 = Normal programme Channel down = PRG 2 = ISISA T programme
4. Switch on the receiver (power on).
PREPROGRAMMING IS NOW COMPLETED. CHANNEL SELECTION: The channel number
selected is shown on the digital display ie. F01­F99 or C01-C99. Channels preceded with an F are stored channels and can be accessed eit­her directly using the up and down keys or by keying in the respective channel number. Non­stored channels can only be accessed by key­ing in the channel number.
INDIVIDUAL PROGRAMMING
It is possible to alter each channel or change the preset completely if you so wish. Switch to the channel you would like to alter and enter the video & audio frequencies, polarisation, bandwidth and decoder mode (if necessary) as follows:
POLARISATION: Select the required polari­sation (vertical or horizontal) by pressing the V/H button on the remote control.
VIDEO TUNING: After pressing either the up and down tuning key a 3-figure number is sho­wn on the display (frequency in MHz). To alter the frequency you have the option of either pres­sing the up and down tuning keys or the requi­red frequency can be keyed in directly using the remote control. Although you must always ent­er a 4-digit number for the frequency (ie. 0950-
2050) only the last 3 digits are displayed. DEV SELECTION: ASTRA channels are pre-
programmed Hi (high video level). Other chan­nels can be programmed Lo (low video level).
AUDIO TUNING:
a) First press either the Mono/Stereo button to
select 0- Mono, 0-0 for Stereo.
b) If stereo is selected the button A/B should be
pressed to obtain A (left) or B (right) side audio outputs.
c) The correct frequency can be set using the
audio up/down keys. After selecting A or B the required frequency can be keyed in directly and will be shown on the digital display.
d) Tune audio bandwidth I---I wide,-II- narrow by
pressing the W/N button.
IF STEREO HAS BEEN SELECTED IT IS NECESSARY TO REPEAT STAGES b) AND c) FOR THE OTHER FREQUENCY.
NOTE:
i)
Holding down the AUDIO and TUNING buttons
accelerates the frequency change.
ii) 5 seconds is allowed for keying in the
frequencies directly. If this is not achieved (ie. entry does not
appear on the display) press the appropriate
TUNING or AUDIO key and re-enter.
STORING: Once you have attained the best possible picture and sound quality you can sto­re the channel by using for example a ball point pen to press the sunken STORE button for 1-2 seconds.
ERASING: To erase stored information press and hold down the ERASE key as above. Now the erased channel can only be selected by ente­ring the number via the key pad of the remote control (see also CHANNEL SELECTION).
TechniSat®VC 2002 S
Watching a scrambled Videocrypt programme
1. Select a coded channel (eg. Movie Channel or Sky Movies Plus).
2. Insert the viewing card as indicated by the arrow.
3. After a few seconds the descrambled picture will appear on the screen.
NOTE: Do not bend or damage the card in any way .
SCREEN MESSAGES:
Please insert card” - make sure that the card is inserted correctly. “Please wait” - descrambled picture should appear in a few seconds. “Your card is invalid” - ensure the card is ins- erted correctly and/or has not been damaged. “Your card has expired” - a replacement card is required. “Channel blocked” - indicates there is some- thing wrong with your card. In the case of the last 3 messages, first of all try turning the receiver off, disconnect from the mains and leave for one minute. Turn on again and retry card. If this still fails contact BSkyB.
8
PROGRAMMING
CONNECTING A SEPARATE DECODER: (*)
To choose between normal and decoder mode press DECODER: In position “n” the reception signal will be connec­ted directly from the TV or video recorder. In position “d” the coded signal (non-Videocrypt coded channels) is sent from the scart socket to the decoder. The decoded signal is sent back to the receiver and can be picked up at the scart socket or at the UHF output connection. Press the D MODE button to select the deco­der signal according to the following table:
D1: Flat, MAC compatible signal D2: PAL de-emphasised baseband signal D3: Unclamped video signal D4: Clamped video signal
Be sure to consider the recommendation of the manufacturer regarding the connection of the decoder.
(*)DOES NOT APPL Y TO VIDEOCRYPT INTER­NAL DECODER, BUT REFERS TO THE USE OF A SEPARATE DECODER FOR NON­VIDEOCRYPT CODED CHANNELS.
FREQUENCY SHIFT:
If the LNB of the outdoor unit does not supply the exact IF-frequency, it is possible to change it as follows:
1. Press the “V/H” button for about 3 seconds.
2. The receiver displays “AFC”.
3. Enter “999”.
4. The receiver displays “0.0”.
5. Now it can be tuned up or down (+/- 5 MHz) with the tuning buttons.
6. Once you have achieved the best picture quality you can store the frequency shift with the STORE button.
NOTE: The frequency shift applies for all channels.
TechniSat®VC 2002 S
9
SPECIFICATIONS
1
. Tuner
Input Frequency: 950 - 2050 MHz Input Impedance: 75 Ohm Input Level: -70 dBm to -25 dBm Input Connector: F-type LNB Power: +18 V constant at 300 mA max.
(+14 V/18 V for V/H-LNB) Bandwidth: 26 MHz Gain Control: AGC Tuning: PLL frequency synthesized
2. Clamped Video
De-Emphasis: CCIR REC. 405-1, 625 LINE Bandwidth: 5 MHz Output Level: 1 V p-p Output Connector: Scart and RCA phono
3. Decoder Output
Mode: 4 different modes D1 - D4 Output Level: 1 V p-p Output Connector: Scart and RCA phono (L, R) Output Impedance: 75 Ohm
4. Audio
Frequency Range: 5.0 to 8.8 MHz adjustable Mode: Mono/Stereo selectable Bandwidth: 150 KHz/280 KHz selectable De-Emphasis: 50 µs/J17 Frequency Response: 20 Hz to 15 kHz Output Level: 2 V p-p Output Connector: Scart and RCA phono (L, R)
5. RF Modulator
UHF: 30 - 39 tunable, preset to 36,
switchable PAL I / PAL B UHF Output Level: 75 +/- 4 dBµV UHF Output Connector: IEC Male Ant. Input Connector: IEC Female
6. Others
Supply Voltage 240 Volt 50 Hz
Technical specifications are subject to improvements.
TechniSat® VC 2002 S
10
PROBLEM CAUSE/SOLUTION No picture or sound, no 1. No power. Make certain that your VC 2002 S
indicator lights is connected to an appropriate AC power supply.
2. Power switch is off. Press power button.
3. Fuse has blown. Replace.
No picture or sound, but 1. TV is not not set to the right channel, indicator lights are lit or fine tuning on TV is incorrectly adjusted.
Check that TV is tuned to appropriate UHF channel when using modulator output.
2. Antenna is not pointed at a satellite. Check that antenna is aligned to an operating satellite.
3. Bad cable connections. Check all cable connections and connectors.
4. Defective LNB. Replace.
Indicator lights are lit Internal fuse has blown. except "stand by" Contact dealer.
Picture has sparkles or 1. Antenna is not aligned to an operating is grainy satellite. Readjust antenna.
2. Video fine tuning incorrectly adjusted. Readjust accordingly .
3. Excessive signal loss between LNB and recei­ver. Install a line amplifier.
4. LNB is defective. Replace.
5. Bad connections. Check all coaxial connections and plugs.
6. Water in coaxial cable. Dry out if necessary and use suitable connector sealant on all outside connections.
Audio sounds distorted 1. Selected AUDIO is not tuned to correct
subcarrier. Check the required audio frequency with the programme table.
Remote control does not operate 1. Weak battery in remote control. Replace. or has poor range.
TROUBLE SHOOTING
IF AUDIO (MHz) MODE BAND DE-EM VIDEO- DECODER
DECODER
POLARI-
MHz A B WIDTH PHASIS LEVEL VIDEO MODE SATION
(kHz) (External)
73 Hit Radio 1.318 7,74 7,92 STER 150 J 17 High NOR D-4 Ver 74 Holland FM 1.479 7,56 7,38 MONO 150 J 17 High NOR D-4 Ver 75 Radio Super Gold 1.377 7,92 7,74 MONO 150 J 17 High NOR D-4 Ver 76 Giant FM 1.377 7,74 7,92 MONO 150 J 17 High NOR D-4 Ver 77 RTL Radio NL 1.391 7,74 7,92 STER 150 J 17 High NOR D-4 Hor 78 Rad.Schwed.Int. 1.597 7,74 7,92 MONO 150 J 17 High NOR D-4 Ver 79 Schweizer Rad.Int. 1.332 7,20 7,02 MONO 150 J 17 High NOR D-4 Hor 80 Sunrise Radio 1.479 7,38 7,56 MONO 150 J 17 High NOR D-4 Ver 81 RTL Radio D 1.523 7,38 7,56 STER 150 J 17 High NOR D-4 Hor 82 DEUTSCHLANDF. III 1.288 7,92 7,74 MONO 150 J 17 High NOR D-4 Ver 83 DEUTSCHLANDF. II 1.288 7,74 7,92 MONO 150 J 17 High NOR D-4 Ver 84 DEUTSCHLANDF. I 1.288 7,38 7,56 STER 150 J 17 High NOR D-4 Ver 85 DTSCH. WELLE II 1.229 7,56 6,50 MONO 150 J 17 High NOR D-4 Ver 86 DTSCH. WELLE I 1.229 7,38 7,56 MONO 150 J 17 High NOR D-4 Ver 87 NDR 2 1.582 7,38 7,56 STER 150 J 17 High NOR D-4 Hor 88 SWF 3 1.494 7,38 7,56 STER 150 J 17 High NOR D-4 Hor 89 STAR SAT RADIO 1.406 7,38 7,56 STER 150 J 17 High NOR D-4 Ver 90 OPUS RADIO 1.332 7,38 7,56 STER 150 J 17 High NOR D-4 Hor 91 Solar Radio 1.509 7,38 7,56 MONO 150 J 17 High NOR D-4 Ver 92 POWER FM 1.421 7,38 7,56 STER 150 J 17 High NOR D-4 Hor 93 RADIO LUX. INT. 1.391 7,38 7,56 STER 150 J 17 High NOR D-4 Hor 94 ASDA-FM 1.436 7,74 7,92 MONO 150 J 17 High NOR D-4 Ver 95 Quality Europe FM 1.436 7,38 7,56 STER 150 J 17 High NOR D-4 Ver 96 CNN Radio 1.627 7,92 7,74 MONO 150 J 17 High NOR D-4 Ver 97 Hit Radio 1.318 7,74 7,92 STER 150 J 17 High NOR D-4 Ver 98 SKY RADIO 1.318 7,38 7,56 STER 150 J 17 High NOR D-4 Ver 99 RADIOROPA INFO 1.406 7,74 7,92 STER 150 J 17 High NOR D-4 Ver
PS: The first IF have been calculated on the basis of the following data:
1. For the frequency range 10.95 - 11.7 GHz LOF 10.000 GHz *only with external Decoder
2. For the frequency range 11.7 - 12.5 GHz LOF 10.750 GHz
3. For the frequency range 12.5 - 12.75 GHz LOF 11.475 GHz LOF - Local Oscillator Frequency
43 - 72 free
ASTRA TV
ASTRA RADIO
11
PROGRAMME TABLE 1 (V/H-LNB)
IF AUDIO (MHz) MODE BAND DE-EM VIDEO- DECODER
DECODER
POLARI-
MHz A B WIDTH PHASIS LEVEL VIDEO MODE SATION
(kHz) (External)
1 SKY MOVIES PLUS 1.436 7,02 7,20 STER 150 J 17 High NOR D-4 Ver 2 Movie Channel 1.479 7,02 7,20 STER 150 J 17 High NOR D-4 Ver 3
SKY M. GOLD / Adult.Ch.
1.597 7,02 7,20 STER 150 J 17 High NOR D-4 Ver 4 SKY ONE 1.318 7,02 7,20 STER 150 J 17 High NOR D-4 Ver 5 SKY NEWS 1.377 7,02 7,20 STER 150 J 17 High NOR D-4 Ver 6 CNN 1.627 6,50 7,02 MONO 280 50 µs High NOR D-4 Ver 7 Sky Sports 1.509 7,02 7,20 STER 150 J 17 High NOR D-4 Ver 8 Screensport 1.214 7,02 7,20 MONO 150 J 17 High NOR D-4 Hor 9 EUROSPORT 1.259 6,50 7,02 MONO 280 50 µs High NOR D-4 Ver 10 MTV 1.421 7,02 7,20 STER 150 J 17 High NOR D-4 Hor 11 LIFESTYLE 1.273 7,02 7,20 STER 150 J 17 High NOR D-4 Hor 12 CHILDR.CH. 1.273 7,38 7,20 MONO 150 J 17 High NOR D-4 Hor 13 Child.Ch. 1.568 7,38 7,20 MONO 150 J 17 High NOR D-4 Ver 14 JSTV 1.568 7,02 7,20 STER 150 J 17 High NOR D-4 Ver 15 FILMNET / D2-MAC 1.362 7,02 7,20 MONO 150 J 17 High NOR D-2 Hor 16 RTL 4 VERONIQUE 1.391 7,02 7,20 STER 150 J 17 High NOR D-4 Hor 17 RTL PLUS 1.229 6,50 7,02 MONO 280 50 µs High NOR D-4 Ver 18 SAT. 1 1.288 6,50 7,02 MONO 280 50 µs High NOR D-4 Ver 19 PRO 7 1.406 7,02 7,20 STER 150 J 17 High NOR D-4 Ver 20 TELE 5 1.523 7,02 7,20 STER 150 J 17 High NOR D-4 Hor 21 ARD 1 PLUS 1.494 7,02 7,20 STER 150 J 17 High NOR D-4 Hor 22 3 SAT 1.347 7,02 7,20 STER 150 J 17 High NOR D-4 Ver 23 NORD 3 1.582 7,02 7,20 STER 150 J 17 High NOR D-4 Hor 24 PREMIERE* 1.464 7,02 7,20 STER 150 J 17 High NOR D-4 Hor 25 TELECLUB* 1.332 6,50 7,02 MONO 280 50 µs High NOR D-3 Hor 26 TV 3 Schwed.* 1.244 6,50 7,02 MONO 280 50 µs High NOR D-1 Hor 27 TV 1000* 1.303 6,50 7,02 MONO 280 50 µs High NOR D-1 Hor 28 UK GOLD 1.553 6,50 7,02 MONO 280 50 µs High NOR D-1 Hor 29 TV 3 Daenemark* 1.612 6,50 7,02 MONO 280 50 µs High NOR D-1 Hor 30 1.641 6,50 7,02 MONO 280 50 µs High NOR D-4 Hor 31 TV 3 Norw.* 1.671 6,50 7,02 MONO 280 50 µs High NOR D-1 Hor 32 1.686 6,50 7,02 MONO 280 50 µs High NOR D-4 Ver
12
IF AUDIO (MHz) MODE BAND DE-EM DECODER
DECODER
VIDEO
MHz A B WIDTH PHASIS VIDEO MODE LEVEL
(kHz) (External) 89 SWF 3 1244 7.38 7.56 STER 150 J17 NOR D-4 HIGH 90 POWER FM 1171 7.38 7.56 STER 150 J17 NOR D-4 HIGH 91 OPUS RADIO 1082 7.38 7.56 STER 150 J17 NOR D-4 HIGH 92 RADIO LUX. INT. 1141 7.38 7.56 STER 150 J17 NOR D-4 HIGH 93 SKY RADIO 1618 7.38 7.56 STER 150 J17 NOR D-4 HIGH 94 STAR SAT RADIO 1706 7.38 7.56 STER 150 J17 NOR D-4 HIGH 95 DTSCH. WELLE II 1529 7.56 6.50 MONO 150 J17 NOR D-4 HIGH 96 DTSCH. WELLE I 1529 7.38 7.56 MONO 150 J17 NOR D-4 HIGH 97 DEUTSCHLANDF. II 1588 7.74 7.56 STER 150 J17 NOR D-4 HIGH 98 DEUTSCHLANDF. I 1588 7.38 7.56 STER 150 J17 NOR D-4 HIGH 99 RADIOROPA INFO 1706 7.74 7.92 STER 150 J17 NOR D-4 HIGH
PROGRAMME TABLE 2 (ISISAT-LNB)
IF AUDIO (MHz) MODE BAND DE-EM DECODER
DECODER
VIDEO
MHz A B WIDTH PHASIS VIDEO MODE LEVEL
(kHz) (External) 01 PRO 7 1706 6.50 7.02 MONO 280 50µs NOR D-4 HIGH 02 RTL PLUS 1529 6.50 7.02 MONO 280 50µs NOR D-4 HIGH 03 SAT.1 1588 6.50 7.02 MONO 280 50µs NOR D-4 HIGH 04 TELE 5 1273 7.02 7.20 STER 150 J17 NOR D-4 HIGH 05 ARD 1 PLUS 1244 7.02 7.20 STER 150 J17 NOR D-4 HIGH 06 3 SAT 1647 7.02 7.20 STER 150 J17 NOR D-4 HIGH 07 NORD 3 1332 7.02 7.20 STER 150 J17 NOR D-4 HIGH 08 SPORTKANAL 0964 7.02 7.20 MONO 150 J17 NOR D-4 HIGH 09 EUROSPORT 1559 7.20 7.02 MONO 150 J17 NOR D-4 HIGH 10 MTV 1171 7.02 7.20 STER 150 J17 NOR D-4 HIGH 11 PREMIERE 1214 7.02 7.20 STER 150 J17 NOR D-4 HIGH 12 SKY ONE 1618 7.02 7.20 STER 150 J17 NOR D-4 HIGH 13 SKY NEWS 1677 7.02 7.20 STER 150 J17 NOR D-4 HIGH 14 RTL 4 VERONIQUE 1141 7.02 7.20 STER 150 J17 NOR D-4 HIGH 15 LIFESTYLE, CHILD 1023 7.02 7.20 STER 150 J17 NOR D-4 HIGH 16 SES VIDEO 1303 6.50 7.02 MONO 280 50µs NOR D-4 HIGH 17 NORD 3 1332 6.50 7.02 MONO 280 50µs NOR D-4 HIGH 18 1362 6.50 7.02 MONO 280 50µs NOR D-4 HIGH 19 TELECLUB 1082 6.50 7.02 MONO 280 50µs NOR D-3 HIGH 20 FILMNET 1112 6.60 7.02 MONO 280 50µs NOR D-2 HIGH 21 1559 6.50 7.02 MONO 280 50µs NOR D-4 HIGH 22 JSTV 1868 6.50 7.02 MONO 280 50µs NOR D-4 HIGH 23 1897 6.50 7.02 MONO 280 50µs NOR D-4 HIGH 24 CNN 1927 6.50 7.02 MONO 280 50µs NOR D-4 HIGH 25 1956 6.50 7.02 MONO 280 50µs NOR D-4 HIGH 26 1986 6.50 7.02 MONO 280 50µs NOR D-4 HIGH 27 0964 6.50 7.02 MONO 280 50µs NOR D-4 HIGH 28 0979 6.50 7.02 MONO 280 50µs NOR D-4 HIGH 29 0994 6.50 7.02 MONO 280 50µs NOR D-4 HIGH 30 1008 6.50 7.02 MONO 280 50µs NOR D-4 HIGH 31 1023 6.50 7.02 MONO 280 50µs NOR D-4 HIGH 32 1038 6.50 7.02 MONO 280 50µs NOR D-4 HIGH 33 1053 6.50 7.02 MONO 280 50µs NOR D-4 HIGH 34 1067 6.50 7.02 MONO 280 50µs NOR D-4 HIGH 35 1082 6.50 7.02 MONO 280 50µs NOR D-4 HIGH 36 1097 6.50 7.02 MONO 280 50µs NOR D-4 HIGH 37 1112 6.50 7.02 MONO 280 50µs NOR D-4 HIGH 38 1126 6.50 7.02 MONO 280 50µs NOR D-4 HIGH 39 1141 6.50 7.02 MONO 280 50µs NOR D-4 HIGH 40 1156 6.50 7.02 MONO 280 50µs NOR D-4 HIGH 41 1171 6.50 7.02 MONO 280 50µs NOR D-4 HIGH 42 1186 6.50 7.02 MONO 280 50µs NOR D-4 HIGH
PS: The first IF have been calculated on the basis of the following data:
1. For the frequency range 10.95 - 11.7 GHz LOF 10.000 GHz
2. For the frequency range 11.7 - 12.5 GHz LOF 10.750 GHz
3. For the frequency range 12.5 - 12.75 GHz LOF 11.475 GHz LOF - Local Oscillator Frequency
43 - 88 free
ASTRA TV
ASTRA RADIO
Loading...