TechniSat EUROKLASSIK 1 Short Instructions

Page 1
Short instructions
TechniSat
DigiCorder Satellite receiver
Your unit carries the CE symbol and complies with all relevant EU standards. Subject to change and printing errors. Correct as at 05/08
TechniSat and DigiCorder HD S2 X are registered tradehighlights of TechniSat Digital GmbH Postfach 560 54541 Daun www.technisat.de
Page 2
Automatic Search
Satellite
Channel searching Transponder
Manual Search
Country
Protection of minors Time zone
Program journal Date/Time
Standby clock
Basic settings
Settings IRC code
Screen format
Quickstart
Picture settings HDMI resolution
Audio language
HDMI colour space
Sound settings Subtitle language
TV SCART mode
Antenna c onguration Dolby Digital
Zoom
Special functions AV synchronism
OSD
Main Menu HDMI audio format
PVR
System conguration
Media Player
Service settings
Restore factory set-
tings
Network
Timer overview Delete all programs
Remote access
Hard disk timer Update software
Miscellaneous
Timer organising
Video rec. timer Copy settings
TV-Lists organising Channel change timer
Record organising
Timer settings
Radio lists organising Music copying
Picture copying
Hard disk organising
Record copying
CI Slot 1
Hard disk information
CI Slot 2
Conditional access
Hard disk mainte-
nance
Smartcard 1
Smartcard 2
Menu language
Page 3
Disposal advice
The packaging for your unit consists entirely of recyclable material. Please sort the items appropriately, and sort them for disposal via your local waste “Disposal system”. Please note that spent batteries (from the remote control) as well as electronic components should not be disposed of in your household refuse, but in accordance with your local regulations (special waste, handing back to the outlet where purchased).
Safety advice
For your own protection, please read the safety instructions carefully before commencing operation of your new unit. The manufacturer accepts no responsibility for damage caused by inappropriate operation, or by non­compliance with safety precautions.
> To ensure sufcient ventilation, position the device on a at, even surface and do not place any objects
on the lid of the device. This surface has ventilation slots that ensure heat can escape from inside the unit.
> Do not place any burning objects, such as burning candles, on top of the unit.
> Do not subject the unit to water spray or droplets, and do not place any objects lled with liquid, e.g.
vases, on top of the unit. > The unit may only be operated in a temperate climate. > Never open the unit housing! You are in danger of receiving an electric shock. Any necessary repairs
should be carried out only by qualied service personnel.
Contents:
Safety advice ..............................................................................................................................................3
When not in operation ...............................................................................................................................4
Help:..................................................................................................................................... ......................5
Initial installation............................................................................................................................ ..........5
Switching on and off ...................................................................................................................................6
Channel selectios .......................................................................................................................................6
Optional channels ......................................................................................................................................7
Additional channel information ................................................................................................................7
Volume control ..........................................................................................................................................8
TV/Radio switching ....................................................................................................................................8
Access Electronic Programme Guide (EPG): .........................................................................................8
Hard disk operation ...................................................................................................................................8
Recording .................................................................................................................................................8
Playback .................................................................................................................................................12
Pause/Still picture ...................................................................................................................................13
Fast Forward and Rewind ......................................................................................................................13
Slow motion ............................................................................................................................................14
Single frame progress ............................................................................................................................14
MP3 Playback ........................................................................................................................................14
Playback/Reproduction of pictures ........................................................................................................15
Manage hard disk ...................................................................................................................................16
Sort Channels / Congure Favourites List ............................................................................................19
Exit Menus ................................................................................................................................................21
Page 4
Card reader for the smartcard:
> Slide the smartcard (with the gold chip fac-
ing down and in the intended direction of
insertion) carefully until it is tted into the
card reader.
Inserting the CI module:
> Follow the instructions of the manufacturer of the
CI module and card.
> Slide the desired smart card into the relevant CI
module.
> Now carefully slide the CI module into the appro-
priate slot.
Video recorder
In the following cases, you should disconnect the unit from the mains power supply, and consult a quali-
ed technician:
> the mains cable or the mains plug is damaged
> the unit was exposed to liquid, or liquid has run into the unit > in case of signicant malfunction
> in case of severe external damage
When not in operation
During an electrical storm, or when the unit will not be used for a lengthy period of time (e.g. while you are on holiday), disconnect the unit from the mains power supply.
Connecting the DVB receiver a. Mains connection
b. Connecting LNB 1 with LNB Input 1 of the
DVB receiver. (Please note: When operating with an an­tenna signal, the LNB must be connected with the LNB Input 1.)
c. Connecting LNB 2 with LNB Input 2 of the
DVB receiver.
d. Scart connection between the DVB receiver
and the television set.
e. Connecting from the component socket of
the DVB Receiver to the component socket of the TV.
f. Scart connection between the DVB receiver
and the television set.
g. Scart connection from a video player to the
VCR Scart socket of the DVB receiver.
h. Connecting the Audio outputs with a HiFi-/
Surround system.
Operating with 2 antenna signals
To ensure the full functional scope of the digital receiver is usable, the receiver should be operated with
two separate antenna signals / antenna connections, which are tted identically.
b, c Connect LNB Inputs 1 and 2 of the digital receiver via a suitable coaxial cable with your external unit. Operating with 1 antenna signal
In exceptional cases, you may also operate the receiver with just one antenna signal. In this case, how­ever, the recording and PIP functions will only be functional to a limited extent. b Connect the LNB Input 1 of the digital receiver via a suitable coaxial cable with your external unit.
Page 5
Mute
On/Standby
Sleep timer
Remote control option
(Code+OK
at the same time)
Numeric keys
Multifunctional keys
TV/Radio
Recording
OK/
Channel list
On/Off
Arrow keys left/right Volume+ Volume–
Back
Info
Playback functions
Arrow down/Arrow up Channel + /Channel –
Channel +/–
Stop/Freeze frame
Volume +/–
Menu On/Off
Video text
On/Mix/Off
Option button
Operation with a rotating antenna b
During operation with a rotating antenna, connect the DiSEqC engine (Level 1.2) with the LNB input 1.
Connection to a television set d Connect the receiver (HDMI output) and TV (HDMI input) via an HDMI cable.
If your TV is suitably equipped, it will automatically switch to the HDMI input when the digital receiver is
switched on.
Or: e Connect the receiver (component output) and TV (component input) via a component cable. Alternatively: f Use a SCART cable to connect the receiver (SCART socket TV) with the television set
(SCART socket). If your television set is appropriately equipped, it will automatically switch to AV, and thus to satellite operation, when the digital receiver is switched on. Where applicable, it may be necessary to
adapt the type of signal for your television set.
Important operating instruc t ions
The operation of the digital receiver is
simplied by the use of the “On Screen
Displays”, which also serves to reduce
the number of keys required on the
remote control unit. All functions are displayed on the screen, and can be op­erated with a few keys. Related functions are combined in a “MENU”. The function selected is highlighted in colour. The “function keys” red, yellow, green and blue are indicated by colour bars in the bottom line. These colour bars represent different functions in the various menus, which will be activated by pressing the appropriate coloured key (multifunction key) on the remote control. The “Func­tion keys” are only active when a brief description is displayed in the appropri-
ate eld.
Help:
Where available in the menus, pressing the blue function key will cause a help text to be dis­played, pressing again will remove the text from the screen.
Initial installation
When switching on the unit for the rst time, a start window will be displayed, with the installation as­sistant AutoInstall. Please follow the instructions displayed on screen. If you do not implement the initial installation, or if it is not completed, the receiver will commence operation with a standard pre-channeld
conguration.
Antenna conguration
In this installation step you can adjust the digital receiver to the conguration of your antenna. > If you wish to accept the standard antenna setting, use the arrow keys up/down to highlight the eld
Standard and conrm by pressing OK. > If the conguration of your receiving installation does not correspond with the standard setting, highlight
the eld Manual and conrm by pressing OK.
Page 6
DiSEqC
> If you have DiSEqC components in your receiving installation, highlight the eld Activate and conrm by
pressing OK
Position A/Option A
> Use the arrow keys up/down to highlight the satellite you wish to receive at the DiSEqC setting Position
A/Option A and conrm by pressing OK.
Position B/Option A
> Use the arrow keys up/down to highlight the satellite you wish to receive at the DiSEqC setting Position
B/Option A and conrm by pressing OK.
Position A/Option B
> Use the arrow keys up/down to highlight the satellite you wish to receive at the DiSEqC setting Position
A/Option B and conrm by pressing OK.
Position B/Option B
> Use the arrow keys up/down to highlight the satellite you wish to receive at the DiSEqC setting Position
B/Option B and conrm by pressing OK. In the next step, you should check on the correct conguration
of your antenna.
> If you wish to accept the settings entered, use the arrow keys up/down to highlight the eld Yes, and
conrm by pressing OK.
Position A/Option B
> Use the arrow keys up/down to highlight the satellite you wish to receive at the DiSEqC setting Position
A/Option B and conrm by pressing OK.
Position B/Option B
> Use the arrow keys up/down to highlight the satellite you wish to receive at the DiSEqC setting Position
B/Option B and conrm by pressing OK. In the next step, you should check on the correct conguration
of your antenna.
> If you wish to accept the settings entered, use the arrow keys up/down to highlight the eld Yes, and
conrm by pressing OK.
You can abort the initial installation at any time simply by pressing the red function key. Press the green function key to go back to the previous step in the installation procedure. Thus any entries made incor-
rectly can be quickly corrected. If you do not implement the initial installation, or if it is not completed, the receiver will commence operation with a standard pre-channeld conguration.
For daily use
Switching on and off
> Press the On/Standby key either on the digital receiver or the remote control to switch the receiver on. > Press the same key again to switch the receiver off.
Channel selection
Using the channel up/down keys > Use the channel up/down keys on the remote control or on the receiver to move up or down the list one
channel slot at a time.
Page 7
Using the numeric keys
> You may use the numeric keys to enter the desired channel number. For example: 1 for channel 1
1, then 4 for channel 14 2, then 3, then 4 for channel 234
When entering a channel number consisting of several digits, you have approx. 3 seconds after pressing
each number to complete the entry. If you wish to enter a number consisting of only one or two digits, you can speed up the switching procedure by holding the key down on the last digit.
Using the channel list:
> Press the OK key. > Now use the arrow keys up/down to highlight the desired channel. > Press the OK key to display the highlighted channel. > Use the arrow keys up/down to move the highlighter in the list by one line at a time. > Use the arrow keys left/right to move back and forth in the list one page at a time.
Return to the last channel selected
> Pressing the Back key on the remote control will take you back to the last channel selected. > Press the key again to return to the channel previously selected.
Optional features
Certain channels offer the possibility of optional channels. This function makes it possible for you, e.g. during a sports broadcast, to freely select from various camera perspectives (Form 1) or to select from a range of different sporting broadcasts (Bundesliga football).
If a programme includes optional features, this will be indicated by a notication.
> To select one of the possible options, press the option button. A selection window showing the available
options will be displayed.
> Use the arrow keys up/down to highlight the desired option, and conrm by pressing OK.
Select start time
On certain channels, you can select individual lms with different start times. With this in mind, these lms
are available on a round the clock basis at different start times. If a channel features selectable start time, this will be indicated. > To select one of the possible start times, press the option button. A selection window showing the start
times offered will be displayed. > Use the arrow keys up/down to select the desired start time.
> Conrm by pressing OK.
Provided the broadcast for the selected start time is available, you can view this at the desired time.
Additional channel information
Each time you change channels, an information box will be displayed briey, showing the channel slot and
the channel name of the channel selected. In addition, other channel properties will be indicated, such as for Video text, widescreen broadcasts and for encrypted channels. If a TV broadcast is available in mul- tiple languages or with multiple sound channels, or if multiple radio channels are available on a single radio station slot, this will be displayed on screen. You may then proceed as follows to select a different
language or a different audio channel:
> Press the Option key. A list will now be displayed on screen, indicating the languages currently avail-
able.
> Use the arrow keys up/down to highlight the desired language or the desired radio station and conrm
by pressing OK. You may now listen to the channel in the language selected. Your digital receiver is
also equipped to receive monaural channels.
> Use the arrow keys left/right to choose between Mono channel 1 ( ), Mono channel 2 ( ) and Stereo ( ).
Page 8
Volume control
> Adjust the volume of your digital receiver using the Volume + key to increase the volume, and Volume –
to decrease the volume. > Press the mute key to switch the sound on or off.
TV/Radio switching
> By pressing the TV/Radio button, you can switch between TV and Radio operation.
Access Electronic Channel Guide (EPG):
> Press the SFI/EPG key on the remote control of the digital receiver.
The Electronic Channel Guide then appears on the screen. The channels you have selected, or those
of the factory default settings, will be shown with their current channels. You can now also use the EPG
function to obtain information on various channels. In addition, you may use the EPG functions to select
a particular channel, to pre-select a channel, or to set a timer for a channel.
Exit EPG
> Press either the Menu or the TV/Radio key to return to normal operation.
Hard disk operation
Recording Warning!!!
Simultaneous receiving of two encrypted channels
Your receiver also allows you to receive two different encrypted channels simultaneously, using only one CI module and only a single valid Smartcard. However, this is only possible if you use a CI module with the “Dual-Decrypt” function (see details of the CI module manufacturer), both the desired channels are located on the same transmitter and the CI dual decryption function has been correctly selected.
Please ensure that the receiver has acquired the time. During operation, this is displayed in the Infobox
and during standby operation on the display. If this is not the case, leave the receiver switched on to a
selected channel for approximately 30 seconds, so that the receiver can acquire the current time.
1. Immediate recording
Select this recording type, to record the broadcast currently showing immediately with the touch of a but­ton.
2. Time-controlled recording
This function can be used to switch your digital receiver on and off for the selected broadcast, in order to record onto the hard disk when you are away. The time can be channeld either manually or automatically via the EPG function.
3. Timeshift recording
The timeshift recording function makes delayed TV viewing possible. With this function, even while the
recording continues, you can use a time-delayed play back.
Page 9
Warning!
For technical reasons, it is not possible to receive two broadcasts, which are both transmitted in HD format, at the same time. To utilise all the recording facilities of your receiver, you should ensure it is con­nected via two independent antenna connections. This allows you to use the following combinations of
recording and playback:
- Record one broadcast and at the same time, play back another broadcast (even from a different TV
channel; 1 broadcast in HD format and 1 broadcast in SD format or 2 broadcasts in SD format) or a
hard disk recording.
- Record two broadcasts (1 broadcast in HD format and 1 broadcast in SD format or 2 broadcasts in SD
format) at the same time, even when these are received on different channels.
- Record two different broadcasts (even from different channels; Record 1 broadcast in HD format and 1
broadcast in SD format or record 2 broadcasts in SD format at the same time and play back a pre-re-
corded broadcast. If the receiver connection only has one antenna connection available, the available
recording and playback functions will be correspondingly limited as a result.
- Record one broadcast and, at the same time, play back another broadcast of the same channel
(1 broadcast in HD format and 1 broadcast in SD format or 2 broadcasts in SD format) or a hard disk
recording.
- Record two broadcasts of the same channel (1 broadcast in HD format and 1 broadcast in SD format
or 2 broadcasts in SD format) at the same time.
- Record two different broadcasts of the same channel (1 broadcast in HD format and 1 broadcast in
SD format or 2 broadcasts in SD format) and play back a prerecorded broadcast.
Immediate recording
Manually start recording
Option 1
> Switch on the program, which is showing the broadcast which you would like to record.
> Press the record button to record the current broadcast. While the recording continues, the broadcast is
still displayed on the screen.
> To stop the playback of the current broadcast at a specic point, press the yellow function key Play/
Pause. While the recording continues in the background, a still picture appears on the screen.
> T
o continue the playback of this broadcast from this point, press the yellow function key Play/Pause again. You will now view the broadcast with a time delay relative to the live transmission (Timeshift), while the current broadcast is continually recorded in the background.
Option 2
> If you have to interrupt the viewing of a broadcast e.g. due to a telephone call etc., you can halt the play-
back of this broadcast by pressing the yellow function key Play/Pause and start recording the current
broadcast at the same time. While the recording starts in the background, a still picture appears on the
screen.
>
To continue the playback of this broadcast from this point, press the yellow function key Play/Pause again. You will now view the broadcast with a time delay relative to the live transmission (Timeshift), while the current broadcast is continually recorded in the background.
Manually end recording
> First press the OK button to end the recording. > Press the green function key to access the PVR navigator.
> Use the arrow keys up/down to highlight the current recording and conrm by pressing OK.
> Press the green function key Stop and a selection window appears. > Use the arrow keys up/down to select Save, to save the recording onto the hard disk, or Cancel, to can-
cel saving of the broadcast and conrm by pressing OK.
Page 10
10
Automatically end recording
Option 1
> Press the On/Standby key. Now a selection window appears, which should show the details of the cur-
rent recording.
> Use the arrow keys up/down to highlight the line with the desired action.
> Conrm by pressing OK. The receiver completes recording of the broadcast and subsequently reverts
to standby mode.
> When you switch on the receiver before recording is over, a selection window appears, select whether
you wish to view the current broadcast from the start, revert to live mode or switch to the current chan­nel.
> Use the arrow keys up/down to highlight the desired line and conrm by pressing OK. When Start is
selected, the recording will continue in Timeshift operation.
Option 2
> By pressing the Record button, a selection window appears.
> Use the arrow keys up/down to highlight the line with the desired action, e.g. +1 hour, and conrm by
pressing OK. The receiver will now record the channel(s) being broadcast on the channel selected for the time period selected, and will then automatically stop recording.
Timer recordings
With the help of the hard disk timer, you can record broadcasts on the integrated hard disk even when you are away. Your receiver is also equipped with video recorder timers as well as channel switching timers. In terms of their programming, these timers differ only in that the relevant type of timer is specied. In
Standby operation, the hard disk and video recorder timers are shown by a clock symbol on the display. As described in this chapter, you can either program the timer manually or with the help of the EPG func­tion.
1. Hard disk timer
This function can be used to switch your digital receiver on and off for the selected broadcast, in order to record onto the hard disk when you are away. If the receiver was switched on by means of the hard disk timer, this will be indicated by the message “_ PVR Timer” shown in the display. Some functions of the remote control (e.g. Accessing the main menu) are not operational.
2. Video recorder timer
When you use a video recorder timer, your digital receiver will be switched on and off for the channel se­lected, so that it may be recorded, e.g. on a video recorder, in your absence. If the receiver was switched on by means of the video recorder timer, this will be indicated by the message “_ VCR Timer” shown in the display. Some functions of the remote control are not operational. Be careful to note that the relevant recorder must also be channeld.
3. Channel change timer
If your receiver is in normal operating mode, it will switch to the programmed channel at the time selected. In contrast to the setting for a hard disk or video recorder timer, the remote controls remain fully function­al, and the receiver will not be switched off at the end of the channel.
Manual timer programming
> Press the Menu key to display the Main menu. > Use the arrow keys up/down to highlight the line Manage timer.
> Conrm with the OK button, to access the Timer Menu
> Use the arrow keys up/down to select the desired timer type. > Press the OK key to go to the entry window in order to channel a new timer event.
Channel –
> Use the arrow keys to highlight the upper line of the menu. > Press the OK key.
Page 11
11
> In the selection window use the arrow keys up/down to select the desired source (TV or Radio) and
conrm by pressing OK. Depending on the previous setting, either the TV or the radio channel list will
now be displayed.
> Now highlight the desired channel with the help of the numeric keys (channel input) and/or with the help
of the arrow keys. Use the arrow keys up/down to move the highlighter around the list one line at a time and the arrow keys left/right to move the highlighter forwards or backwards one page at a time.
> Press the OK key to accept a channel into the timer memory.
Date
> Use the arrow keys to highlight the column Date. > Use the numeric keys to enter the date (in 4-digit format) on which the timer event is to take place.
Start
> Use the arrow keys to highlight the column Start. > In this line, use the numeric keys to enter the starting time for the timer.
Stop
> Repeat the steps as for “Start” in order to enter the stopping, or ending time (except in the case of chan-
nel change timers).
Repeat
> Use the arrow keys to highlight the column Rep. > Press the OK key.
A selection window will be displayed, presenting various repeat options:
1x Timer once T Daily repeat
1 W Repeat once per week
1-5 Repeat only on weekdays 6-7 Repeat only on weekends > Use the arrow keys up/down to select the desired function. > Press OK to accept the setting.
Accepting data into memory
> When you have completed the programming, press the green function key Accept, to transfer the data
to memory. After the data have been saved into memory, the timer overview appears.
Timer overview
The timer overview function gives you an overview of all timer events already channeld.
> To access the timer overview, rst call up the main menu by pressing the Menu button. > Use the arrow keys up/down to select the entry Manage timer and conrm by pressing OK. The sub-
menu Manage timer will be displayed.
> Use the arrow keys up/down to highlight the line Set highlighter, conrm by pressing OK.
If, when programming, multiple timer events clash, meaning the timer cannot be correctly set, the overlaps are highlighted in red.
Change timer programming
> To change an existing timer setting, access the timer overview function.
> Subsequently, use the arrow keys up/down to highlight the timer event you wish to change.
> Press the green function key Change to go to the settings of the highlighted timer. Make the changes as
described.
> Use the arrow keys up/down to highlight the additional window displayed: Type, before you save to the
timer.
> By pressing the OK key a window with the available timer types will open. > Now use the arrow keys up/down to select the desired timer type.
> To accept the timer type, conrm by pressing OK.
> Press the green function key Save, to save the data in storage.
Page 12
12
Delete timer programming
> To delete an existing timer setting, access the timer overview function.
> Subsequently, use the arrow keys up/down to select the timer to be deleted. > Press the yellow function key Delete. A message will be displayed: “Do you really want to delete this
timer?”
> Use the arrow keys left/right to select Yes.
> To delete the timer, conrm by pressing OK.
Channel new timer event
> To channel a new timer event, use the arrow keys up/down to highlight a blank line in the menu Timer
overview.
> Press the green function key New to call up the input window to channel a new timer event.
> Use the arrow keys up/down to highlight the additional window displayed: Type.
> By pressing the OK key a window with the available timer types will open. > Now use the arrow keys up/down to select the desired timer type.
> To accept the timer type, conrm by pressing OK. > When you have completed the programming, press the green function key Accept, to transfer the data
to memory.
Timer settings (Preliminary or Follow-up time)
During the EPG timer programming, the receiver receives the data of the selected broadcast automati­cally from the EPG data. This allows the start and end time of the broadcast being recorded to be saved precise to the minute. However, there are often cases where the selected broadcast starts somewhat
earlier or later than is specied. In this case, the recorded broadcast will miss out either the start or the
end. To solve this problem, you can set preliminary or follow-up time in one minute steps. The timer now
starts earlier at the specied preliminary time and ends at the set follow-up time later than specied in the
EPG data. > Press the red function key Timer to open a selection window. > Use the arrow keys up/down to highlight the line Timer settings.
> Conrm by pressing OK. A menu appears for adjusting the preliminary or follow-up time.
> Use the arrow keys up/down to highlight the line Timer preliminary time or Timer follow-up time.. > Use the numeric keys to enter the desired preliminary or follow-up time in minutes. > Press the green function key Save, to save the setting and to return to the timer overview.
Timeshift function
The timeshift function allows you the possibility to activate both playback and recording at the same time. This allows time-delayed TV viewing and allows you to view the start of the recording and thus jump throughsections that have already been recorded. At the same time, the recording of the live signal of the broadcast continues.
> To access a specic section of a current recording, the functions Play and Pause are available, as well
as Fast Forward and the jog shuttle.
> Pressing the Info button causes the Infobox to appear with a status bar displayed, which shows the
playback and recording duration.
Setting highlighters while recording
> Press the Record key to open a window showing the functions available.
> Use the arrow keys up/down to highlight the line Set highlighter, conrm by pressing OK. A highlighter
will now be set at the current position. Continue in this manner to set highlighters at all desired places. highlighters can also be placed even during a recording and in the Manage hard disk menu.
Playback
You can access hard disk recordings via the hard disk (PVR-) navigator. These can be accessed in sev­eral ways. Depending on whether you are operating the TV or radio, a list appears with all the TV or radio recordings contained on the hard disk. After access via the navigator, the playback of the highlighted recording already starts.
Page 13
13
Accessing the PVR navigator:
The PVR navigator can be accessed in the following ways:
During normal operation
> Press the OK key to open the channel list navigator. > Press the green function key PVR to switch to the PVR navigator. or > Press the green function key directly to open the PVR navigator.
During recording/playback of a recording
> During a recording/playback of a hard disk recording, you can access the PVR navigator by pressing
the OK button.
Play back hard disk recordings
> First access the PVR navigator. > Use the arrow keys up/down to select the recording you wish to play back. Completed as well as current
recordings can be selected.
> To start the playback, conrm by pressing OK. The indication “Playback_” will be displayed.
Recording information
> First access the PVR navigator. > Use the arrow keys to highlight the recording for which you would like to see further information. > Pressing the yellow function key Status allows information on the highlighted recording to be displayed. > Press the Back button to return to the PVR navigator.
Pause/Still picture
> To halt the playback of a recording (still picture), during playback, press the yellow function key or the
Still picture button. The symbol "Pause _II" will be displayed.
> Press the relevant key again to restart the playback from the same position.
Fast Forward and Rewind
To access a specic section of a recording, your PVR includes variable speed Fast Forward and Rewind
functions. > During playback, press the blue function key for Fast Forward or the red function key for Rewind. The
display indicates “Fast Forward ___” or “Rewind ___”. The recording will now be run at 4x normal speed in the desired direction.
> Press the blue or red function key again and the speed increases to 16x. The display indicates “Fast
Forward ___” or “Rewind ___”.
> Press the blue or red function key again and the speed increases to 64x. The display indicates “Fast
Forward ___” or “Rewind ___”.
> By pressing the blue or red function key again, you can jump forward or backward in 10 minute seg-
ments.
> Once the desired portion of the recording has been reached, you can access normal playback by press-
ing the yellow function key.
Jogshuttle function
In addition, your receiver features a jog-shuttle function, which allows you to go to a specic place in your recording very quickly and precisely. This can be used as follows: > While in playback mode, press the key Jogshuttle on/off (Freeze frame) to go to the jog-shuttle mode.
The playback of the recording will be stopped (freeze frame/pause). The symbol “_II“ will be displayed.
Fast Forward and Rewind
> By pressing the arrow keys right/left, you can adjust both the speed and direction of playback. In the
process, the respective playback mode will be displayed.
> While this is displayed, press the arrow keys __ _ _ or _ _ __, right or left, to jump forwards or backwards
in 10 minute steps.
Page 14
14
Slow motion
> By pressing the right arrow key once, the recording is played back at slow motion speed and the indica-
tion “I_” appears on the display.
Single frame progress
> Press the arrow key up to display the next frame in a forwards direction and press down for display the
previous frame in the backward/reverse direction.
Create image
> By pressing the Record button, an individual image is transferred onto the hard disk. In this way, you
can access and manage created images.
Setting highlighters
> As described before, go to the place in your recording at which you wish to insert a highlighter. > Press the record button to set a highlighter at the actual position. Continue in this manner to set high-
lighters at all desired places. Highlighters can also be set during Record mode as well as in the menu Manage hard disk.
Jump to highlighters
During the playback, it is possible to jump directly to specic sections of the recording, where you have
positioned highlighters. > Pressing the key Option will open a window with the existing highlighters. In addition, the indication
“Current” appears. This highlights the actual playback position on the recording.
> As soon you use the arrow keys up/down to highlight a highlighter, the playback begins at this point. > By pressing the OK button, the window is closed and you switch to normal playback.
End playback
> To exit playback, press the green function key. The playback will be ended and your receiver will revert
to normal operation. In the process, the receiver logs the position on the recording at which playback
was ended. When you restart playback of this recording, it will automatically revert to the point at which
you previously stopped it.
MP3 playback
You can use your receiver to display created images, as well as les, which are saved in MP3 format on
the hard disk or on a device connected via the USB socket. The USB device should be formatted using
the le system FAT 32.
> During normal operation, open the PVR navigator with the green function key. > Press the blue function key NAV Menu. > Use the arrow keys up/down to highlight the line Music. > By pressing OK, the selection of the source medium is now displayed.
> Use the arrow keys up/down to select the source from which you wish to play back the MP3 les. > By pressing OK, a list now appears with the MP3 les contained on the hard disk or on the USB device.
> Use the arrow keys up/down as applicable to initially highlight the folder, which contains the desired
MP3 le, and conrm by pressing OK.
> Use the arrow keys to select from the list the MP3 le you wish to play rst, and conrm by pressing
OK. The le selected will now be played. Thereafter the other les located on the same source medium,
will be played automatically.
Skipping titles/tracks
> By pressing the arrow keys up/down, you can jump forwards or backwards one track.
Pause
> Press the yellow function key to stop the playback operation (Pause).
> Press the key again to resume playing the le from this position.
Page 15
15
Fast Forward and Rewind
> During playback, press the blue function key Fast Forward or the red function key Rewind, several times
if applicable, to advance or rewind the track at 4x, 16x or 64x normal speed.
> During the 64x speed, press the blue or red function button to go forwards or backwards in 10 minute
steps.
> Once the desired section has been reached, you can access normal playback by pressing the yellow
function key.
Stop/End playback
> To stop playback and revert to normal operation, press the TV/Radio button.
Display control
To avoid the need to switch on the television set when navigating the MP3 playback, the latter can be
controlled via the display. An MP3 le is shown on the display with its respective lename. A folder will be indicated by a display of square brackets, e.g. [Popmusic]. The hard drive will be displayed as hard drive
and a USB device will be indicated as USB-device1, USB-device2 etc..
> While the device is in standby mode, press the language selection button. The device now switches
itself on and automatically sets the navigator to the music category.
> Use the arrow keys up/down to select the source from which you wish to play back the MP3 les, and
conrm by pressing OK. If no USB device is connected to the system, only the internal hard drive of the
receiver will be available as a source.
> Now, rst use the arrow keys up/down to select the folder containing the desired MP3 le, and conrm
by pressing OK.
> Use the arrow keys up/down to select from the list the MP3 le you wish to play rst, and conrm by
pressing OK. The le selected will now be played. Thereafter the other les located on the same source
medium will be played automatically.
Playback/reproduction of pictures
You can use your receiver to display created images, as well as les, which are saved in JPG format on
the hard disk or on a device connected via the USB socket. The USB device should be formatted using
the le system FAT 32.
> During normal operation, press the green function key to open the PVR navigator. > Press the red function key Category to open an additional window.
> Use the arrow keys up/down to highlight the line Pictures and conrm by pressing OK.
> Use the arrow keys up/down to select the source from which you wish to view the picture les, and con-
rm by pressing OK. A list showing the picture les available on the hard drive and the USB device will
be displayed.
> Use the arrow keys up/down as applicable to initially highlight the folder, which contains the desired im-
age le, and conrm by pressing OK.
> Use the arrow keys up/down to select from the list of JPG les, which you which to view and conrm
with OK. The picture selected will now be displayed in large format.
Show next/previous picture
> Press the arrow keys up/down to skip to the next or previous picture.
Rotate image
> By pressing the blue or red function key, the image can be rotated in a clockwise or anticlockwise direc-
tion.
Manage hard disk
> Call the Main menu by pressing the key Menu. > Use the arrow keys up/down to highlight the line Timer settings.
> Conrm by pressing OK. The menu Manage hard disk will be displayed.
> Use the arrow keys up/down to move the highlighter within the menu, and to change the individual items
as indicated.
Page 16
16
Manage recordings
This menu allows you to manage your recordings. > Press the OK button, to access the recording submenu. A list appears of the recordings contained on
the hard disk.
> Use the up/down arrow keys to select the desired recording.
Delete
> To delete the highlighted recording, press the red function key Delete.
> To actually delete the recording, use the arrow keys left/right to highlight the eld OK and conrm by
pressing OK.
Parental control
Recordings, which are unsuitable for children and young people, can be locked. These recordings can then only be played back when a 4 digit PIN code is entered. To ensure the parental control function is active, this option (found under menu/settings/child safety) must be activated. > To lock the highlighted recording, press the green function key. The selected recording will now be high-
lighted with the child safety symbol to show it is locked.
Editing
> By pressing the yellow function key Edit, you can access the menu for editing the highlighted hard disk
recording. The hard disk recording will be played back in a preview window. In addition, any highlight­ers included in this recording will be displayed. As standard, the highlighters for the Start and End are present. In addition, a yellow status bar is also shown, which indicates the current playback position and the overall duration of the recording.
> To jump to a section of the recording indicated by a highlighter, highlight the desired highlighter using
the arrow keys up/down and conrm with OK.
Functions
> By pressing the green function key Menu, a window opens with the available functions for editing the
recordings.
> Use the arrow keys up/down to highlight the desired function, and conrm by pressing OK. > Use the arrow keys to highlight the eld OK and accept the name.
Delete portion
Your PVR also allows you to delete selected section (e.g. unwanted sections of commercials) from an existing recording.
Please note:
The deleted sections will be irretrievably removed from the hard disk. To delete a specic section, proceed as follows: The beginning and end of the section that is to be elimi­nated must be indicated by two highlighters. > Mark both the beginning and end of the section to be deleted with one highlighter respectively. > Now use the arrow keys up/down to set the highlighter indicating the beginning of the section to be
deleted. The section to be deleted will now be indicated in red on the progress indicator as well as in the overview of existing highlighters.
> Now press the green function key Menu and use the arrow keys up/down to highlight the line delete sec-
tion.
> Press OK to display a section window.
> To actually delete the section, use the arrow keys right/left to highlight the eld OK and conrm by
pressing OK.
Page 17
17
Extracting a section
This function allows you to copy a section of a recording. A new recording is generated, consisting only of this section. The recording from which this section is copied remains in memory unchanged. To extract a
section, proceed as follows: The beginning and end of the section that is to be copied must be indicated
by two highlighters. > Here, highlight both the beginning and end of the portion to be deleted with one highlighter respectively. > Now use the arrow keys up/down to set the highlighter indicating the beginning of the section to be
copied. The section to be copied will now be indicated in red on the progress indicator as well as in the overview of existing highlighters.
> Now press the green function key Menu and use the arrow keys up/down to highlight the line extract
section.
> Press OK to display a selection window. > To actually copy the section, use the arrow keys right/left to highlight the eld OK and conrm by press-
ing OK. The highlighted section will now be copied to a new recording. Depending on the size of the section, this may take several minutes.
Splitting a recording
This function allows you where, for instance, two successive channels were recorded as a single record­ing, to split these into two individual recordings. Each recording will be split at the point indicated by the
relevant highlighters. Recordings can be split as follows:
> Place a highlighter at the beginning of the section to be extracted. > Now use the arrow keys up/down to highlight the point from which the entire recording should be split. > Now press the green function key Menu and use the arrow keys up/down to highlight the line split re-
cording.
> Press OK to display a selection window. This will show information relating to the two recordings to be
created by the split.
> To actually split the recording, use the arrow keys left/right to highlight the eld OK and conrm by
pressing OK.
Rename recordings
Your PVR extracts information from the transmitted data stream concerning the names of the broadcast channels. If a single recording contains multiple broadcasts, all the names of the recorded broadcasts are
compiled and saved internally. To rename a recording, proceed as follows:
> Now press the green function key Menu and use the arrow keys up/down to highlight the line Rename.
> Conrm by pressing OK. A list of the possible titles will be displayed. > Use the arrow keys up/down to select the title for which you wish to change the name and conrm by
pressing OK.
> In the subsequent section window, use the arrow keys right/left to highlight the eld OK and conrm by
pressing OK.
> If you want to assign a specic name to the recording, use the arrow keys up/down to select the line
New.
> By pressing the OK button, a virtual keyboard is displayed, with which you can input the new name.
Enlarge video
To facilitate the control of a desired section of a recording, the video image of the recording can be en­larged. > Press the green function key Menu to do so and use the arrow keys up/down to highlight the line En-
large video.
> By conrming with OK, the video image is displayed in enlarged form.
> To reduce the size of the video image again, proceed likewise, highlighting the line Shrink video.
Managing music/pictures
You can use your receiver to play back musical tracks in MP3 format and images in JPG format. To copy the relevant data onto the hard disk, connect a USB device, on which the MP3s or JPGs are contained, to
the USB socket of the receiver.
Page 18
18
Please be careful to note, that only MP3 les can be managed from the Music menu, and only JPG les
from the Images menu. > Call up the menu Manage hard drive as described above. > Use the arrow keys up/down to highlight the line Copy music or Copy images, in order to manage the
relevant les.
> Conrm by pressing OK. In the subdivided menu, the left half (set-top box) shows the les and folders
present on the hard disk. The right side (USB device) shows the les and folders, which are contained
on the connected USB device.
> Use the green function key to switch from one USB device to another or the red function key set-top box
to do the same for the hard disk. The rst le or the rst folder of the list is highlighted.
Copy
The Copy function allows you to make a copy of the highlighted le or highlighted folder onto the hard disk or the USB device. The original le or folder also remains in place. > With the help of the arrow keys up/down, highlight the le or folder, which you would like to move.
> Press the blue function key Functions to open a window showing the functions available.
> Use the arrow keys up/down to select the line Copy and conrm by pressing OK. > To copy the selected le or folder, now press the yellow function key Copy. The highlighted le or folder
is now copied and subsequently also appears in the left or right half of the menu.
Highlighting blocks of channels
To highlight several les simultaneously, proceed as follows: > Press the OK key to go to the selection mode. The highlighted le will be indicated with a cross on the
left side.
> You may now use the arrow keys up/down to highlight the previous or following les as well. > After you have highlighted the desired les in this way, press the yellow function key Copy, to copy
these les.
Please be careful to note, that collective copying of folders is not possible! Move
The Move function allows you to move the highlighted le or folder from the source medium (e.g. a USB device) to the target medium (e.g. the hard disk). The moved le or folder will subsequently only be found
on the target medium. > Use the red function key set-top box or the green function key USB device to select the source, in which
the le or folder to be moved is contained.
> With the help of the arrow keys up/down, highlight the le or folder that you wish to move.
> By pressing the blue function key Functions, the function window opens.
> Use the arrow keys up/down to highlight the line Move and conrm by pressing OK. > To move the highlighted le or folder, now press the yellow function key Move.
> To move multiple les at the same time, highlight those desired and subsequently press the yellow func-
tion key Move.
Delete
To delete les or folders, proceed as follows:
> Use the red function key set-top box or the green function key USB device to select the source, in which
the le or folder to be deleted is contained.
> With the help of the arrow keys up/down, highlight the le or folder that you wish to delete.
> Press the blue function key Functions to open a window showing the functions available.
> Use the arrow keys up/down to highlight the line Delete and co with nrm by pressing OK. > To delete the highlighted le or folder, now press the yellow function key Delete. An selection window appears, to conrm whether you really wish to delete the selected les. > Use the arrow keys left/right to highlight the eld Yes and conrm by pressing OK. Or, highlight No, and
conrm by pressing OK to cancel the operation. The les will now be deleted.
Page 19
19
Hard disk information
> By pressing the OK button, information concerning the integrated hard disk is displayed.
Hard disk properties
> Press the OK button, to see an overview of the lled capacity of the hard disk and the number of record-
ings it contains.
Checking hard disk
> To carry out a check of the hard disk, use the arrow keys right/left to highlight the eld Check.
> Press the OK button and conrm by using the arrow keys right/left to highlight the eld OK and conrm-
ing with OK, to start the checking. The hard disk will now be checked. The result will subsequently be
displayed.
Formatting the hard disk
By formatting the hard disk, the le system is renewed. This may be necessary when checks of the hard
disk reveal any error.
Note!
When formatting, the contents of the hard disk will be permanently deleted, meaning all the recordings and multimedia les (e.g. MP3s) will be lost. > To format the hard disk, use the arrow keys right/left to highlight the eld Format. > Press the OK button and conrm by using the arrow keys right/left to mark the eld OK and conrming
with OK, to start the formatting.
Please note!
The device may only be operated with the originally integrated hard disk. Otherwise, this could lead to damage to the device.
With this in mind, never open the device and attempt to exchange the hard disk, since this will render all
warranties null and void.
Sort Channels / Congure Favourites List
This chapter describes how you can change the pre-programming of your digital receiver as well as the
Favourites channel list in accordance with your own preferences. This function is also required to sort
new found channels into the channel list after a channel scan has been performed. In this regard you should know the following: your receiver is equipped with two channel lists, the Favourites list and the Total list. The Favourites channel list includes all the channels you have accepted into the list according to the procedure described below. The Total list includes all channels.
Calling up channel list management
To customise the Favourites list, proceed as follows:
> Press the Menu key to display the Main menu. > Use the arrow keys up/down to highlight the line Manage TV lists, in order to work on the TV list, or
Manage Radio lists, in order to work on the radio list.
> Conrm by pressing OK. The channel list management required to work on the respective Favourites
list will be displayed. Favourites list (TV or radio list). The Favourites list will be displayed on the right half of the screen. This is now active, with the currently selected channel being highlighted. The alpha­betically sorted Total list will be displayed on the left half of the screen. The Total list includes all avail­able channels.
> Press the red function key to move the highlighter to the Total list. This is now active. > Press the red function key again to open a selection window. Here you have the option of sorting the
Total list according to various selection criteria (e.g. all channels, all free-to-air, all new channels, all channels found, all English channels, etc.) or sorted by Provider.
> Use the arrow keys up/down to select the desired channel list (e.g. Total list).
> Conrm by pressing OK. An additional selection window will now be displayed.
> Now use the arrow keys up/down to specify the selection criterion according to which the Total list is to
be sorted.
Page 20
20
Select e.g. All broadcasters, to display all available channels in the overall list or All new, to display only newly found channels since the last search was carried out or All English, to display only English lan­guage channels.
> Conrm by pressing OK. Now, depending on your selection, a channel list containing e.g. all channels,
all new or all English-language channels will be displayed. Channels already included in the Favourites list are indicated by a check-highlighter.
> Press the red function key Channels resp. the green function key TV List to switch back and forth be-
tween the Favourites list and the Total list. The currently active list will be indicated by a blue highlighter.
Adding channels to the Favourites list
To accept channels from the Total list into the Favourites list, call up the channel list manager as de­scribed in Point, and go to the Total list. > Press the blue function key Functions. A selection window showing the available functions will be dis-
played.
> Use the arrow keys up/down to highlight the item Add.
> Conrm by pressing OK.
> Use the arrow keys up/down to highlight a channel you wish to accept into the Favourites list. > Press the yellow function key Add to accept the highlighted channel into the Favourites list.
Highlighting blocks of channels
To highlight several channels simultaneously, proceed as follows:
> Press the OK key to go to the selection mode. The highlighted channel will be indicated by a cross on
the left.
> You may now use the arrow keys up/down to highlight the previous or following channels as well.
> When you have highlighted your selected channels in this way press the yellow function key. Add, to
include the highlighted channels in the Favourites list.
Deleting channels
To delete channels from the favourites list, access the channel list management. The Favourites list will be displayed and active. > Press the blue function key Functions. A selection window showing the available functions will be dis-
played.
> Use the arrow keys up/down to highlight the line Remove.
> Conrm by pressing OK.
> Use the arrow keys up/down to highlight a channel you wish to delete from the list.
> Press the yellow function key Delete. The inquiry “Remove channel/s from the list ? appears.
> Use the arrow keys left/right to highlight Yes or No.
> Conrm by pressing OK. The channels deleted in this manner will, however, remain in the Total list, and
can be added to the Favourites list again at any time.
Deleting from the Total list
To remove channels from the Total list, proceed as described above. However, after calling up the chan-
nel list management, press the red function key Channels to rst switch to the Total list, then select the
function Delete.
Sorting channels
To sort the order of channels in the Favourites list according to your preferences, call up the channel list manager. The Favourites list will be displayed and active. > Press the blue function key Functions. A window showing the available functions will be displayed. > Use the arrow keys up/down to highlight the line Sort.
> Conrm by pressing OK.
> Use the arrow keys up/down to highlight the channel, which you wish to place at another position of the
list.
Page 21
21
> Now press the yellow function key Sort. A double arrow will appear next to the channel selected. > Now use either the arrow keys up/down or the numeric keys to place the channel in the desired position
in the channel list.
> Press the yellow function key Sort to enter the new position of the channel into memory.
Exit Menus
Press the TV/Radio key to return to normal operation.
Further Information in more detail can be found on the Internet at the site www.technisat.com
2233560000700
Page 22
22
Page 23
23
Page 24
24
Page 25
DiSEqC
1.2
Integrated Video Recorder
PP VV RR
For receiving free-to-air and encrypted
(e.g. VIACCESS, CONAX, IRDETO, SECA etc.)
HD satellite Programmes.
With two PCMCIA slots for use
with CI modules.
Operating manual
DigiCorder HD S2X
Digital Twin HD-Receiver
with
integrated Hard drive
Page 26
1 Contents
1 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
2 Illustrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
3 Please read this first . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Disposal advice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Safety notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
When not in use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Important notes on operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Important note on data security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
4 Connecting the DVB receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
4.1 Mains power connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
4.2 External unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
4.2.1 Operation with 2 antenna signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
4.2.2 Operation with 1 antenna signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
4.2.3 Operation with a rotating antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
4.3 Connection to a television set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
4.4 Video cassette recorder (VCR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
4.5 HiFi/Surround Sound amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
4.7 Serial interface (RS 232) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
4.8 USB socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
5 Initial installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
6 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
6.1 Operating language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
6.2 Basic settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
6.2.1 Country . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
6.2.2 Time zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
6.2.3 Date/hourt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
6.2.4 Standby clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
6.2.5 Remote control code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
6.2.6 Quickstart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
6.3 Picture settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
6.4 Sound settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
6.5 Antenna adjustment and settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
6.5.1 Multi-tenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
6.5.2 Switching DiSEqC on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
6.5.3 Antenna signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
6.5.4 Setting the switching matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
6.5.5 Additional settings/LNB properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
6.5.6 Rotating antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
6.6 Special functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
6.6.1 Several Favourites lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
6.6.2 Display time Information Banner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
6.6.3 CI dual decoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
6.6.4 Radio background image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
6.6.5 Memory format radio recordings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
6.6.6 Font size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
2
1
Page 27
6.6.7 Network settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
7 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
7.1 Switching on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
7.2 Programme selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
7.2.1 Using the programme up/down keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
7.2.2 Using the numeric keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
7.2.3 Using the Navigator (programme list) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
7.2.3.1 Selecting a list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
7.2.4 Calling up blocked programmes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
7.2.5 Infobox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
7.3 Receiving encrypted programmes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
7.3.1 Option channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
7.3.2 Selecting starting time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
7.3.3 Simultaneous reception of two encrypted programmes . . . . . . . . . . . . . . . . . . . . . . .30
7.4 Volume control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
7.5 Selecting a different language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
7.5.1 Dolby Digital . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
7.6 TV/Radio switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
7.7 Return to last programme previously selected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
7.8 Display clock and programme information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
7.9 Additional programme information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
7.10 Transponder information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
7.11 Freeze frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
7.12 Videotext . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
7.13 Subtitles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
7.14 PIP function (picture in picture) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
7.15 Zoom picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
7.16 EPGplus Electronic Programme Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
7.16.1 Downloading EPGplus data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
7.16.2 Interrupting the download procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
7.16.3 Calling up the Electronic Programme Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
7.16.4 Now (Table with current programme contents) . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
7.16.5 Next . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
7.16.6 More . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
7.16.7 EPGplus - functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
7.16.7.1 EPGplus information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
7.16.7.2 EPGplus Timer programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
7.16.7.3 EPGplus programme overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
7.16.7.4 EPGplus overview by type of programme (genre) . . . . . . . . . . . . . . . . . . . . . . . .39
7.16.8 Ending EPGplus mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
7.17 Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
8 Hard drive operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
8.1 Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
8.1.1 Instant recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
8.1.2 Timer recordings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
8.1.2.1 Manual programming of timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
8.1.2.2 Timer overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
8.1.2.3 Changing Timer programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
8.1.2.4 Delete Timer programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
5
1
Page 28
8.1.2.5 How to programme new event timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
8.1.3 Timeshift function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
8.1.3 Timeshift-Funktion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
8.1.4 Setting markers while recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
8.2 Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
8.2.1 Playing back recordings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
8.2.1.1 Reproducing hard drive recordings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
8.2.1.2 Pause/Freeze frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
8.2.1.3 Fast forward and rewind . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
8.2.1.4 Jogshuttle function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
8.2.1.5 Setting markers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
8.2.1.6 Jumping to markers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
8.2.1.7 End playback session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
8.2.2 MP3 playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
8.2.2.1 Screen controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
8.2.2.2 Display controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
8.2.2.3 MP3 playback modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
8.2.2.4 Playlist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
8.2.3 Viewing pictures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
8.2.3.1 Slide show . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
8.2.3.2 Playlist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
8.3 Managing the hard drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
8.3.1 Managing recordings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
8.3.1.1 Deleting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
8.3.1.2 Parental control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
8.3.1.3 Edit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
8.3.2 Managing music/pictures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
8.3.2.1 Copying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
8.3.2.2 Move . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
8.3.2.3 Deleting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
8.3.2.4 Sampling MP3 files/showing picture files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
8.3.3 Copying recordings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
8.3.3.1 Export . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
8.3.3.2 Preview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
8.3.3.3 Deleting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
8.3.4 Hard drive information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
8.3.5 Hard drive maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
9 Changing basic programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
9.1 Configuring the Favourites list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
9.1.1 Calling up the programme list manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
9.1.2 Selecting Favourites list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
9.1.3 Select Total list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
9.1.4 Adding programmes to the Favourites list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
9.1.5 Deleting programmes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
9.1.6 Sorting programmes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
9.2 Programming the electronic programme guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
9.2.1 Updating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
9.2.2 Updating time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
9.2.3 Start category . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
6
1
Page 29
3
2
2 Illustrations
blue fast forward
red rewind
yellowPause,
playback
greenPVR Navigator,
Stop
On/Standby
Programme list on/off
Back
Volume +
Menu on/off
Sound on/off
Language select*
PIP (picture in picture)
Sleep timer
Option*
in TV mode: select sound/subtitles, special functions
in radio mode:
stations by switching the sound sub-carriers
Volume -
Programm +
Programme -
TV/radio mode
Videotext on/off*
Freeze frame
Jogshuttle on/off
EPG
Record
Multifunctional keys
Programme +
Volume -
Volume -
Numeric keys
0/AV
OK
Volume +
Info
Right arrow key
Left arrow key
Up arrow key
Down arrow key
Remote control option: By switching the remote control option, this remote control unit can be used to control two TechniSat receivers and one TechniSat television set with the same coding. > To switch the remote control option, press the desired key (SAT1, SAT2 or TV)
and OK simultaneously! Please note: To operate this receiver, the remote control option selected here and the remote control code set as described under Point 6.2.3 must correspond.
Remote control
* This function is only available when the
corresponding data is transmitted to the selected programme list position.
Page 30
Front of unit
Back of unit
4
2
LNB
input 1
LNB
input 2
SCART socket
TV
Components; Video und Audio­outputs analogue
Video-
Output
Audio outputs digital
Audio outputs
analogue
SCART socket
VCR
RS 232 interface
Mains jack
HDMI-output
Mains power socket
Inserting the CI modules: > Follow the instructions provided by the manufacturers of the CI module and card. > Insert the desired Smartcard into the appropriate CI module. > Now carefully insert the complete CI module into the slot provided.
Component
outputs
OK-key
Back
Play/Pause
Mode
CI module
slot 2
Eject buttons for
CI modules
On/
Standby
Arrow keys
USB socket
Alphanumeric
display
CI module
slot 1
Card-reader: > Insert the CONAX-Smartcard (golden chip facing
downwards and in the direction of insertion) until the point of contact in the card-reader.
Page 31
7
1
9.2.4 EPG channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
9.2.5 Selecting a TV channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
9.2.6 Selecting radio channels/programmes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
9.3 Parental control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
9.3.1 PIN query mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
9.3.2 Changing the PIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
9.3.3 Selecting a TV channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
9.3.4 Selecting radio channels/programmes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
9.4 Programme search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
9.4.1 Automatic scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
9.4.2 Satellite scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
9.4.3 Transponder scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
9.4.4 Manual search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
9.4.5 During the search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
9.4.6 After the search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
9.5 Service settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
9.5.1 Activate factory default setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
9.5.2 Delete all programmes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
9.5.3 Updating the programme list (ISIPRO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
9.5.3.1 New programme list available . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
9.5.3.2 Decline programme list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
9.5.3.3 Update programme list automatically . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
9.5.3.4 Update programme list manually . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
9.5.4 Updating software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
9.5.4.1 New software available . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
9.5.5 Copying settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
9.6 System configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
9.7 Encryption system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
10 Use with a rotating antenna (DiSEqC 1.2) . . . . . . . . . . . . . . . . . . . . .80
10.1 East and West limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
10.1.1 Deleting existing limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
10.1.2 Setting the East limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
10.1.3 Setting the West limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
10.2 Geo-positioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
10.3 Setting a satellite position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
10.3.1 Select satellite position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
10.3.2 Adjusting the satellite antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
10.4 Current satellite list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
10.4.1 Turning to a satellite position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
10.5 Deleting a satellite position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
10.6 Reference position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
12 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
13 Troubleshooting guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
Page 32
Dear customer,
congratulations on your decision to purchase the DigiCorder HD S2X digital receiver. The operating manual supplied is intended to help you utilise the comprehensive functions of your new digital receiver to the fullest extent.
We have kept the operating instructions as brief as possible, and have used terminology that everybody can understand.
The range of functions of your receiver is constantly being expanded in the form of software updates. This means that additional steps in the operation may be added that are not yet described in this operating manual, or the operation of existing functions may be changed. For this reason you should occasionally visit the TechniSat homepage, to download the current version of the operating manual.
We wish you many years of viewing pleasure with your TechniSat DigiCorder HD S2X !
Your
TechniSat Team
HDMI, the HDMI logo and High Definition Multimedia interface are trademarks registered by HDMI Licensing LLC.
Dolby and the “Double D” symbol are the trademarks of Dolby Laboratories. Manufactured under licence from Dolby Laboratories.
Your unit bears the CE mark and meets all the necessary EU standards.
Subject to changes and printing errors. As at 10/07
TechniSat and DigiCorder HD S2X are registered trademarks of
TechniSat Digital GmbH
Postfach 560
54541 Daun
www.technisat.de
Technical Hotline
0180/5005-910*
*0.14 EUR/min. from Deutsche Telekom AG numbers
Note!
If you need to return your unit, please use the following address only:
TechniSat Teledigital AG
Service-Center
Löderburger Str. 94
39418 Staßfurt
8
3
Page 33
3 Please read this first
> Before starting to use your receiver, please check that all the components have been
supplied correctly. The following should be included:1 digital receiver, 1 mains cable, 1 remote control, 1 operating manual, 1 guarantee card, 2 batteries (1.5V microcells).
> Please insert the batteries supplied into the battery compartment of the remote control
unit, with attention to the correct polarity as indicated.
Disposal advice
The packaging material of your receiver consists entirely of recyclable materials. Please sort the components appropriately, and dispose of them in line with your local waste disposal regulations.
At the end of its useful life span, this receiver may not be disposed of in your regular domestic refuse bin. It must be taken to a recycling collection point for electrical and electronic equipment. The symbol on the product, the operating manual or the packaging will indicate this.
The materials can be recycled or reused according to their labelling. By ensuring that valuable raw materials are used again you can make an important contribution towards protecting our environment.
Please ask your local authority about available disposal facilities.
Ensure that the spent batteries from the remote control are not put in with the household waste but are disposed of appropriately (handed in at specialist shops, special waste).
9
3
Page 34
Safety notes
For your own protection, please read through the safety precautions carefully before proceeding to operate your new unit. The manufacturer will accept no liability for injuries or damage caused by inappropriate handling or non-compliance with the safety precautions.
- The appliance has a fully integrated hard drive. There is no provision for this drive to be exchanged other than by an authorised TechniSat retailer/technician. Any unauthorised replacement of the hard drive will mean that TechniSat will no longer guarantee that the appliance complies with legal requirements (e.g. laws relating to appliance and product safety, laws relating to electromagnetic compatibility of appliances). The CE mark will no longer be valid. When the altered product is sold on, the person responsible for the alteration will become the manufacturer and will be liable accordingly. The TechniSat guarantee will no longer apply either and warranty rights may be lost.
- The appliance should only be operated in a moderate climate.
- To ensure adequate ventilation, place the appliance on a flat, even surface and do not place any objects on top of it, as there are ventilation slots here to allow heat to escape from the interior.
- Do not place any burning objects, e.g. lit candles on top of the unit.
- Do not expose the unit to dripping or sprayed water and do not place any objects filled with water, e.g. vases, on top of it. If water gets into the unit, pull out the mains plug immediately and contact Customer Service.
- Do not operate any sources of heat near the unit, which could heat it up additionally.
- Do not poke any objects through the ventilation slots.
- Never open the unit. Otherwise you will be at risk of an electric shock. Any necessary repairs should only be carried out by trained personnel.
10
3
Page 35
In the following cases you should disconnect the receiver from the mains power, and should consult an expert:
> the mains cable or the mains plug are damaged
> the receiver was exposed to liquid, or liquid has run into the unit
> in case of severe malfunctions
> in case of significant external damage
When not in use
During a storm or when not in use for a long period (e.g. holiday), the unit should be disconnected from the mains and the antenna cable should be removed. Before disconnecting the unit from the mains, you should first switch it to standby and then wait until the time appears in the display and the red LED lights up.
Important notes on operation
The use of so-called “On Screen Displays” (OSD) means that operation of the digital receiver is simplified, and the number of keys on the remote control unit reduced. All functions are displayed on screen, and can be controlled by means of a few simple keystrokes. Functions that are logically connected are combined in a “MENU”. Any function selected will be indicated in a different colour. The function keys red, yellow, blue and green are indicated by coloured bars at the bottom of the screen. In the various menus, these coloured bars represent different functions, which can be implemented by pressing the appropriate coloured keys (multi-function keys) on the remote control. The function keys are only activated when a brief description is displayed in the appropriate field. Key names and terms that appear in the OSD menu are shown in black type in this operating manual.
Help: If present, help text can be shown and hidden by pressing the blue function key.
Important note on data security
We recommend that you save a backup copy of the data on your DigiCorder before handing the receiver over to the specialists for maintenance.
Recreating data is not part of the maintenance and repair work. TechniSat will accept no responsibility for loss of or damage to data during the repair process
11
3
Page 36
4 Connecting the DVB receiver
a. Mains connection
b. Connection between the LNB 1 and the LNB input 1 of the DVB receiver. (Please
note: when operating the unit with one antenna signal, the LNB must be connected to the LNB input 1.)
c. Connection between the LNB 2 and the LNB input 2 of the DVB receiver.
d. HDMI connection of the DVB receiver with the TV set.
e. Scart connection between the DVB receiver and television set.
f. Scart connection between the video recorder and the VCR scart socket of the
DVB receiver.
g. Connection between the audio outputs and a hifi system
12
4
VCR
a
g
e
c
f
d
b
Page 37
The references a b c etc. mentioned below relate to the illustration on page 12.
4.1 Mains power connection
The digital receiver should only be connected to the mains power supply when all the cable connections with other components of the system have been made. This helps to avoid damage to the digital receiver as well as to other components.
a When you have made all the other connections, use the mains cable supplied to
connect the receiver to a mains power outlet 230 V/50-60 Hz.
4.2 External unit
4.2.1 Operation with 2 antenna signals
To utilise the full range of functions of your digital receiver, you should preferably operate it with two separate antenna signals.
b, c Use suitable co-axial cables to connect the LNB inputs 1 and 2 of the digital
receiver with your external unit. Please also note Point 6.4 (antenna settings).
4.2.2 Operation with 1 antenna signal
In exceptional cases you can also operate your receiver with only a single antenna signal. In this case, however, both the recording function and the PIP function will only be available in restricted form. (see point 6.4.2)
b Use a suitable co-axial cable to connect the LNB input 1 of the digital receiver with
your external unit.
4.2.3 Operation with a rotating antenna
b When using a rotating antenna, connect the DiSEqC motor (Level 1.2) with the LNB
input 1.
4.3 Connection to a television set
When you have connected your digital receiver with your television set, it may be necessary to adjust the signal type or the mode of the Scart socket to your television set.
d Use a SCART cable to connect the receiver (SCART socket TV) with the
television set (SCART socket). If your television set is appropriately equipped, it will automatically switch to AV, and thus to satellite operation, when the digital receiver is switched on.
e Connect the receiver (HDMI output) and TV set (HDMI input) using an HDMI cable.
If your TV set is appropriately equipped it will automatically switch this over to the HDMI input when the digital receiver is switched on.
13
4
Page 38
4.4 Video cassette recorder (VCR)
f Connect the video recorder to the SCART socket VCR. During playback, the video
recorder will provide a switching signal to the digital receiver. This will allow the video recorder signal to be routed automatically to the TV set. If your video recorder does not supply a switching current, use the 0/AV key to switch your digital receiver to the external input AV. Press this key again to return to normal operation.
4.5 HiFi/Surround Sound amplifier
To achieve the best possible sound quality, you can connect the digital receiver to a HiFi/Surround Sound amplifier.
4.5.1 Analogue
g Using a suitable cable, connect the Audio R and Audio L cinch sockets of the
digital receiver to an input of your HiFi amplifier (e.g. CD or AUX; Note that the phono input is not suitable!)
4.5.2 Digital
g gIf your amplifier is equipped with a suitable electrical or optical input, connect the
socket AUDIO OUT DIGITAL electrical resp. AUDIO OUT DIGITAL optical with the electrical resp. the optical input of your amplifier.
Depending on the channel, the sampling rates 32, 44.1 and 48 kHz are available. Also, where broadcast, the Dolby Digital signal is available at this output.
4.7 Serial interface (RS 232)
The USB Serial interface serves to update the operating software as well as proprogramming in conjunction with a PC.
4.8 USB-Buchse
The RS 232 interface serves to update the operating software as well as transferring data on or from the hard drive.
14
4
Page 39
5 Initial installation
After you have read the safety notes and connected the unit as described in Chapter 4, switch the unit on as described in Chapter 7. When switching on the receiver for the first time, the starting window of the installation assistant AutoInstall will be displayed. The installation assistant allows you to make the most important settings of your digital receiver in the simplest way possible. At each step of the installation there will be an explanation as to which settings can be made.
You can interrupt the initial installation by pressing the red function key in the starting window of the installation assistant.
In the following steps of the installation, you can then confirm the settings made by pressing the green function key; you will then be taken to the next step of the installation procedure.
If you press the red function key you will be taken to the previous step of the installation, thus giving you an opportunity to correct errors at any time.
If the initial installation is not performed, or if it is aborted, the receiver will commence operation with a standard pre-programmed procedure.
The initial installation process shown here serves merely as an example.
The exact process of the initial installation will depend on the settings you select. Please therefore follow all instructions displayed on screen carefully
Operating language
> When starting the installation assistant, the first selection window to be displayed will
be that for the Operating language.
> Using the arrow keys, select the desired operating language.
> Confirm by pressing the green function key Accept.
Country setting
> Using the arrow keys, select the country in which the unit is being used. The
selection made here will result in the time zone being set, and will affect the sorting of the programme list.
> Using the green function key confirm Accept in order to accept the selection of the
picture format.
Picture format
> Using the arrow keys right/left adjust the picture format of the connected TV set.
Depending on your selection the automatic alignment of the picture to the TV set will take place.
> To accept the selection and to gain access to the selection of antenna signals confirm
with OK.
Antenna signals
Here you must select how many antenna signals are connected to the receiver.
> Using the right/left arrow keys select whether you have connected one or two
antenna signals.
15
5
Page 40
> Use the green function key Accept to confirm and accept the selection, and to go
to the antenna configuration
Antenna configuration
This step of the installation allows you to adjust the setting of your digital receiver to the configuration of your antenna.
> If you wish to accept the standard antenna configuration, press the green function
key Accept. In this case proceed with the point “Software update”.
> If the configuration of your reception installation does not conform to the standard
setting, press the yellow function key Change.
> Carry out the antenna setting according to your receiver, as described in detail under
point 6.5, and then press the red function key Back, in order to return to the antenna configuration.
> Use the green function key Accept to confirm and accept the settings, and to go to
the software update.
Software updating
When you have completed making the antenna settings, the digital receiver will check whether any new version of the software for the receiver is available via satellite. If a new version is available, you can perform an automatic software update.
> Press the green function key Update.
The new software for your unit will now be downloaded. *This procedure may take a few minutes.
> If you do not wish to download the new software at this time, press the yellow
function key Skip.
> If now new software is available at the present time, press the green function key
Continue. You will then proceed to the programme search function.
Programme/channel search/ISIPRO
You have various options of searching for new channels, resp. of updating the programme list. You can either use the ISIPRO programme list function to download a new programme list for your receiver from the satellite, or you can perform a programme scan/search.
> To download a current programme list, use the up/down arrow keys to mark the
line ISIPRO programme list update.
> Confirm using the green function key Start.
The current programme list will now be downloaded from the satellite. Please note any messages displayed on screen, as well as the explanations under Point 9.5.3.
If you wish to perform a programme scan, proceed as follows:
> Use the up/down arrow keys to mark the field All programmes if you wish to
search for both free-to-air and encrypted programmes, or All unencrypted if you wish to search only for free-to-air Programmes.
> Start the scanning procedure by pressing the green function key, and an automatic
programme scan will be performed.
16
5
Page 41
All the satellites included in your antenna configuration will be scanned for Programmes. This procedure may take a few minutes. Please note any messages displayed on screen.
Loading EPGplus data
Your digital receiver has an Electronic Programme Guide, EPGplus Electronic Programme Guide. Your receiver must first download the EPGplus data from the satellite in order for the Electronic Programme Guide data to be displayed. Your receiver will start loading the EPGplus data automatically for this purpose after the programme list update or programme scan has finished. This procedure can take up to 30 minutes.
> If you do not want to wait for the EPGplus data to load, you can skip the process. To
do this, press the yellow function key Skip. The EPGplus data will then be updated automatically the following night, or you can update it manually at any time (see Point 7.16.1).
Ending the installation assistant
> Confirm the final message of the installation assistant by pressing the green function
key Finish, to return to normal operation.
17
5
Page 42
6 Settings
Now that you have connected your new digital receiver, and commenced operating it, you can, if you wish, proceed to optimise its functions for your preferences.
6.1 Operating language
This menu item gives you the opportunity of setting the language used in all the menus according to your preference.
> Use the Menu key to call up the Main menu.
> Now use the up/down arrow keys to mark the menu line Operating language.
> Confirm by pressing OK.
The sub-menu Operating language will be displayed.
> Use the up/down arrow keys to select the desired language.
> Press the OK key to store the entry, and to return to the Main menu.
> By pressing the red function key Back you will return to Normal operation
without saving the setting.
6.2 Basic settings
Under this point, you will find out how to adapt the receiver to your individual requirements.
> Use the Menu key to call up the Main menu.
> Use the arrow keys up/down to mark the line Settings.
> Confirm by pressing OK.
The sub-menu Settings will be displayed
> Use the arrow keys up/down to mark the line Basic settings.
> Confirm by pressing OK.
> Use the arrow keys up/down to move the marker within the menu and to change
the individual positions as indicated. When selecting a menu item, please also note any messages displayed on screen. The following settings/adjustments can be made:
6.2.1 Country
This function allows the adjustments for the difference to GMT, as well as the change-over from standard to daylight savings (summer) time to be made automatically.
> By pressing the OK key another window will open.
> In this window choose your country using the arrow keys and then confirm with
OK.
6.2.2 Time zone
Your receiver is equipped with a clock. This is synchronised to Greenwich Mean Time via satellite.
> If under “country” (point 6.2.1) the setting was user-defined then you must simply
set the time on the clock with the assistance of the right/left arrow keys until it matches your local time. For Germany, this difference is +1 hour, and + 2 hours in summer.
18
6
Page 43
6.2.3 Date/hour
In this menu point decide whether the hour and the date should be automatically read in from a determined programme after switching on.
> By pressing the OK key another window will open.
> In this window use the up/down arrow keys to select either the entry Automatic
or select the programme from which the hour and the date should be read in and confirm the selection with OK.
6.2.4 Standby clock
In this line you can decide whether the current time is to be shown in the display while the receiver is in standby mode.
> In this line, use the arrow keys left/right to set the mode of the standby clock to
on or off.
6.2.5 Remote control code
At this stage you must decide whether your receiver should be allocated to the remote control option SAT1 or SAT2.
> To do this, press the SAT1 or SAT2 key and the OK key on the remote control
simultaneously in this line.
6.2.6 Quickstart
In this line you switch the quickstart on/off . If quickstart is switched on your appliance will start more quickly from standby, although the standby will use more current.
> Switch the quickstart on/off by using the left/right arrow keys.
Accepting settings
To store the settings made in this menu to memory, please proceed as follows:
> Press the green function key Accept to store the changes made, and to return to
the menu Settings.
alternatively:
> Press the red function key Back.
A query then appears.
> If you wish to accept the changes, use the arrow keys left/right to click on the
field Ye s , and confirm by pressing OK. You will now return to the previous menu.
> Press the TV/Radio key to return to normal operation. Settings will not be saved.
6.3 Picture settings
To optimise your digital receiver onto you TV set you can undertake further settings in the Menu Picture Settings.
> Use the Menu key to call up the Main menu.
> Use the arrow keys up/down to mark the line Settings.
> Confirm by pressing OK.
The sub-menu Settings will be displayed
19
6
Page 44
> Now, using the up/down arrow keys, mark the line Picture Settings.
> Confirm by pressing OK.
The Menu Picture settings will appear.
> Use the arrow keys up/down to move the marker within the menu and to change
the individual positions as indicated. When selecting a menu item, please also note any messages displayed on screen. The following settings/adjustments can be made:
6.3.1 Picture format
> Use the arrow keys left/right to set the picture format of your TV set
appropriately, to 4:3 or 16:9. This function automatically adjusts the picture format to that of your television set.
6.3.2 HDMI resolution
> By pressing the OK key a window opens showing the resolutions available.
> Use the up/down arrow keys to selected the desired resolution or auto for
automatic setting of the resolution.
6.3.3 TV SCART mode
> In this line, use the arrow keys left/right to set the parameter appropriate to your
TV set, to the options FBAS, RGB or S-Video. For standard sets use the setting FBAS.
Accepting settings
To store the settings made in this menu to memory, please proceed as follows:
> Press the green function key Accept to store the changes made,
and to return to the menu Settings.
alternatively:
> Press the red function key Back.
A query then appears.
> If you wish to accept the changes, use the arrow keys left/right to click on the
field Ye s , and confirm by pressing OK. You will now return to the previous menu.
> Press the TV/Radio key to return to normal operation.
Settings will not be saved.
6.4 Sound settings
In order to optimise your digital receiver onto your TV set you can undertake further settings in the menu sound settings.
> Use the Menu key to call up the Main menu.
> Use the arrow keys up/down to mark the line Settings.
> Confirm by pressing OK.
The sub-menu Settings will be displayed
> Use the up/down arrow keys to mark the line Sound Settings.
20
6
Page 45
> Confirm by pressing OK.
The Menu Picture settings will appear
6.4.1 Audio speech
> In this line, use the arrow keys left/right to select your preferred language.
Where an appropriate signal is broadcast, this function will, after a scan, automatically set this language.
6.4.2 Sub-title language
Your DVB receiver is able to display subtitles. If the function Subtitles is switched on, and the language selected is being broadcast, these will be displayed automatically.
> In this line, use the arrow keys left/right to select your subtitle language. If the function is not activated, subtitles can also be switched on manually. The availability of
subtitles is indicated by display of the message Subtitles. Please also note Point 7.13 of the operating manual.
6.4.3 Dolby Digital
Various movies are broadcast in Dolby Digital format. This will be indicated in the info
window after the programme has been selected by the Dolby symbol . If you have a Dolby Digital 5.1-channel amplifier, you can, where broadcast, enjoy appropriate movies in 5.1-channel Dolby Digital sound. The only requirement is that the digital output Audio Out Digital (see Point 4.6.2) of your DVB receiver must be connected to the digital input of your Dolby Digital 5.1-channel amplifier
> Use the left/right arrow keys to switch the Dolby Digital function on or off. If the Dolby Digital function is switched on, these broadcasts will automatically be
reproduced in Dolby Digital format. If the function is not switched on (off), Dolby Digital sound can also be switched on manually. Please also note Point 7.5.1 of the operating manual.
Accepting settings
To store the settings made in this menu to memory, please proceed as follows:
> Press the green function key Accept to store the changes made, and to return to
the menu Settings.
alternatively:
> Press the red function key Back.
A corresponding query then appears.
> If you wish to accept the changes, use the arrow keys left/right to click on the
field Ye s , and confirm by pressing OK. You will now return to the previous menu.
> Press the TV/Radio key to return to normal operation.
Settings will not be saved.
6.5 Antenna settings
Once you have set the digital receiver to your own individual preferences, it may still be necessary to adjust the digital receiver to your antenna. The menu Antenna settings lists the satellites set in terms of the installation assistant. If the installation assistant was
21
6
Page 46
prematurely terminated, the satellite positions ASTRA and EUTELSAT will be pre­programmed. If you also wish to receive other satellites, or if you are using a different LNB, set your digital receiver to the desired data as follows:
> Use the Menu key to call up the Main menu.
> Use the arrow keys up/down to mark the line Settings.
> Confirm by pressing OK.
The menu Settings will be displayed.
> Now use the arrow keys up/down to mark the line Antenna settings (DVB-S).
> Confirm by pressing OK.
The menu Antenna settings will be displayed (DVB-S).
The following settings can be made in this sub-menu:
6.5.1 Multi-tenna
If the receiver is operated on a multi-tenna-LNB then under this menu point you could automatically adjust the switch positions on the multi-tenna-LNB.
> Use the OK key to automatically adjust the switch positions.
6.5.2 Switching DiSEqC on and off
DiSEqC (Digital Satellite Equipment Control) is a digital switching/controlling signal used to control DiSEqC-compatible components via the antenna cable. If your external unit is equipped with DiSEqC components, you must switch the DiSEqC controlling function:
> In this line, use the arrow keys left/right to switch DiSEqC on or off.
As only one LNB can be controlled when the DiSEqC function is switched off, the menu is limited to the configuration of a single LNB
6.5.3 Antenna signals
Your receiver is equipped with two tuners. This allows you to record one programme while viewing another programme. So that you can enjoy the full benefit of the functions of your twin receiver for both recording and playback, you should definitely use two separate antenna connections (antenna signals). Please also note Point 8.1.
> In this line, use the arrow keys left/right to set the number of antenna signals to
2, if you are connecting your receiver to two separate antenna connections. If only one antenna connection is available, then set this item to 1.
To utilise all the recording facilities of your receiver, you should ensure it is connected via two independent antenna connections. This allows you to use the following combinations of recording and playback:
- Recording a programme and simultaneously watching another programme (1 programme in HD format and 1 programme in SD format or 2 programmes in SD format) or call up any recording on the hard drive.
- Simultaneously record two programmes (1 programme in HD format and 1 programme in SD format or 2 programmes in SD format) even if these are received in differing reception fields.
- Simultaneously receive two different programmes (even differing fields of reception; 1 programme in HD format and 1 programme in SD format or 2 programmes in SD format) and at the same time show a previously recorded programme.
If only one antenna connection is available for connection to the receiver, only a limited range of recording and playback options is available.
22
6
Page 47
- Record a programme and at the same time another programme from the same reception field (1 programme in HD format and 1 programme in SD format or
25 programmes in SD format) or show any programme from the hard drive.
- Simultaneously record two programmes from the same reception band (15 programme in HD format and 1 programme in SD format or 2 programmes in SD5format).
- Simultaneously record two different programmes from the same reception band (15 programme in HD format and 1 programme in SD format or 2 programmes in SD­format) and at the same time play a pre-recorded programme.
6.5.4 Setting the switching matrix
The menu lists the four switching criteria for the DiSEqC control. You receiver is pre­programmed so that ASTRA is received on switch setting A/A and Eutelsat is received on setting B/A of a multi-switch. If the switching matrix of your receiving installation is set up differently, or if you are receiving different satellites, you can adjust the settings of your digital receiver to those of the receiving installation as follows.
> Use the arrow keys to select a DiSEqC switch position (1-4) to which you wish to
allocate a satellite (e.g. A/B 3 No satellite), and mark this line.
> Press the OK key. Example 1: 2 satellites (Twin-LNBs)
A selection table listing various satellites will now be displayed.
>
Use the
arrow keys to mark the desired satellite. Use the up/down arrow keys to move the marker up or down one line at a time, or use the left/right arrow keys to move the marker backward or forward one page at a time. If the desired satellite is not included in the list, please use one of the reserve slots, marked User 1 to User 13.
> Confirm by pressing OK.
The marked satellite will now be added to the menu Antenna settings at the previously marked position
You can now adjust the settings in the menu Antenna settings, in this manner until the settings in this menu correspond to those of your receiving unit. For any switching criteria that you do not require, use the setting No satellite.
23
6
Page 48
System examples
6.5.5 Additional settings/LNB properties
Once you have completed adjusting the switching matrix of your DVB receiver to the requirements of your receiving installation, you must still check and, where necessary, correct the other settings for your receiving unit.
> Use the left/right arrow keys to move the marker to the column Configuration.
> Now, in the line in which you wish to check or change the settings, use the up/down
arrow keys to mark the field Continue.
> Confirm by pressing OK.
A sub-menu will be displayed in which you can make settings related to the LNB, and can set up a test transponder.
The following settings/adjustments can be made:
LNB Type
> Use the left/right arrow keys to enter the type of LNB you are using. The options
are Single LNB, Quattro LNB, DisiCon 1 LNB, DisiCon 2 LNB, DisiCon 4 LNB, C-Band LNB, Circular LNB, SatCR LNB and a User LNB for manual entry of LNB data.
> If you have selected the SatCR LNB, you must then use the arrow keys to mark
the line Setup and you must then start the setup by pressing the OK key. A SatCR Scan will now be performed. Please take note of the further information displayed on the screen
Test-Transponder
The following points of this menu need only be entered if you wish to check a satellite signal of a specific satellite.
Transponder frequency
> In this line, use the numeric keys to enter a frequency on which digital
programmes are broadcast.
A B
Position
2/1
Output
A B
Position
2/1
Output
Example 1: 2 satellites (Twin-LNBs)
Astra 19,2°
Eutelsat 13°
A B C D
4/1
Output
A B C D
4/1
Output
Example 2: 4 satellites (Twin-LNBs)
Astra 19,2°/ Eutelsat 13°
Eurobird-Astra 28,5°/ Türksat 42°
Multiswitch
9/8
Outputs
Multiswitch
9/8
Outputs
A B
Option
Output
A B
Option
Output
Example 3: 4 satellites (Quattro-LNBs)
Astra 19,2°/ Eutelsat 13°
Eurobird-Astra 28,5°/ Türksat 42°
24
6
Page 49
Polarisation
> Use the up/down arrow keys to enter the desired polarisation plane (horizontal or
vertical).
Symbol rate
The symbol rate indicates the volume of data broadcast per second. This figure could be shown as, for example, 27500 (27500 symbols per second).
> Use the numeric keys to enter the correct symbol rate.
User LNB
If you have entered User LNB under the heading DiSEqC type, you can make further settings:
LOF low band LOF (Local Oscillator Frequency) is the frequency at which an LNB converts the received frequency into what is known as the 1st intermediate frequency, which can then be received by the digital receiver. So-called Universal LNBs work with 2 LOFs, in order to convert the full frequency range of 10.7 to 11.8 GHz (low-band) and 11.7 to 12.75 GHz (high-band).
> In this line use the numeric keys to enter the LOF of the low band of your LNB.
LOF high band
> In this line use the numeric keys to enter the LOF of the high band of your LNB.
LOF transition
> In this line use the numeric keys to enter the frequency at which your LNB
switches from the low band to the high band.
Signal level/quality
If you have entered the details of the test transponder correctly, the signal strength and quality will be indicated in these lines
6.5.6 Rotating antenna
If you are operating your digital receiver in conjunction with a rotating antenna equipped with a DiSEqC motor (Level 1.2), switch the DiSEqC control (Point 6.4.1) on and please note Point 4.2.3 and Point 10 of the operating manual.
6.6 Special functions
This menu allows you to make the settings for CI dual decoding, as well as for the duration for which the Infobox will be displayed, in addition to the function required to switch several Favourites lists on or off.
> Press the Menu key to call up the Main Menu.
> Use the arrow keys up/down to mark the line Settings and confirm by pressing OK.
> Now use the arrow keys up/down to mark the line Special functions.
> Confirm by pressing OK.
The menu Special functions will be displayed.
> Use the arrow keys up/down to mark the entry you wish to change.
6.6.1 Several Favourites lists
> Use the arrow keys left/right to switch the function for several Favourites lists on
resp. off.
25
6
Page 50
If the function is switched on you can configure four lists of favourites (main list, favourites 1, favourites 2 and favourites 3). The ex-works programming can be found in the main list. When the function is switched off only the main list is active.
6.6.2 Display time Information Banner
> Use the numeric keys to set the desired display time for the Infobox. This can be
varied from 1 second to 15 seconds.
6.6.3 CI dual decoding
The CI dual decoding feature allows you to receive two different encrypted programmes simultaneously, using only one CI module and only a single valid Smartcard.
> Use the left/right arrow keys to select the CI slot holding the CI module for dual
decoding. Select CI1, CI2 or CI1+CI2. If you prefer automatic recognition, select auto. The setting off indicates the CI dual decoding feature is switched off. Please also note Point 7.3.3.
6.6.4 Radio background picture
With this function the picture in the radio mode can be switched off. This is kinder to the screen and you will save on current. Here:
on means the picture is switched on also in radio mode.
off means the picture will be turned off, in radio mode, after about 30 seconds and stays
off when a programme is changed.
auto means that the picture will be turned off after about 30 seconds in the radio mode and
will briefly automatically appear during a programme change.
> Use the right/left arrow keys to set on, off or auto.
6.6.5 Memory format radio recordings
Here you can select whether radio recordings on the hard drive should additionally be saved in the MP2-format. These can be copied onto an external appliance.
> Use the right/left arrow keys to set PVR + MP2 in order to additionally save the
radio recordings in the MP2-format.
6.6.6 Font size
You can change the font size for the EPG long texts:
> Set large or small by using the right/left arrow keys.
6.6.7 Network settings
In this submenu you have the option of adapting the digital receiver to your Ethernet network environment.
Accepting settings
To store the settings made in this menu to memory, please proceed as follows:
> Press the green function key Accept to store the changes made, and to return to
the menu Settings.
alternatively:
26
6
Page 51
> Press the red function key Back.
A corresponding query then appears.
> If you wish to accept the changes, use the arrow keys left/right to click on the
field Ye s , and confirm by pressing OK. You will now return to the previous menu.
> Press the TV/Radio key to return to normal operation.
Settings will not be saved.
27
6
Page 52
7 Operation
7.1 Switching on and off
> Switch the digital receiver on by pressing the On/Standby either on the receiver or
on the remote control.
> Press the key again to switch the receiver off again.
> The receiver is now in standby mode, and (if activated in Point 6.2.4) the display
panel will show the current time. If the time is not shown, this must still be acquired by the receiver. To do this, switch the receiver on, and select a major channel such as ZDF for approx. 30 seconds, to automatically acquire the time.
7.2 Programme selection
7.2.1 Using the programme up/down keys
> Use the programme keys up/down either on the receiver or on the remote
control to move up or down the list one programme slot at a time
7.2.2 Using the numeric keys
> Use the numeric keys to enter the desired programme number.
For example:
1 for programme slot 1 1, then 4 for programme slot 14 2, then 3, then 4 for programme slot 234 1, then 5, then 6 then 7 for programme slot 1567
When entering programme numbers with several digits, you have approx. three seconds time after pressing a key to complete the entry. If you wish to enter a number consisting of only one, two or three digits, you can speed up the entry procedure by keeping the key depressed a little longer on the last digit.
7.2.3 Using the Navigator (programme list)
> Press the OK key.
The programme list navigator will be displayed. In TV mode, only TV programmes will be shown, and in Radio mode only radio Programmes. The programme currently selected is marked
> Now use the arrow keys up/down to mark the desired programme.
> Press the OK key and the marked programme will be selected.
> Use the arrow keys up/down to move around the list one line at a time.
> Use the arrow keys left/right to move the marker up or down in the list one page
at a time
7.2.3.1 Selecting a list
To make it easy for you to find programmes, your receiver provides several programme lists. Thus you can choose to select from your Favourites list/TV list (see Point 9.1) or to see the alphabetically sorted Total list or the list by Providers.
28
7
Page 53
> Press the OK key.
The active programme list will be displayed.
> Now, with the assistance of the option key you can open a window with the types of
programme lists (TV lists, TV provider lists and overall TV lists).
The active programme list type is marked.
> Use the arrow keys up/down to select, e.g. the programme list type Total list
and confirm by pressing OK. The alphabetically sorted Total list, containing all programmes, will be displayed.
> Use the arrow keys up/down to mark the programme you wish to view.
> You can get additional information on the current programme by pressing the INFO
key .
> Confirm by pressing OK.
or
> Press the green function key PVR to go direct to the hard drive navigator.
7.2.4 Calling up blocked programmes
If a programme is selected that is blocked by the parental control function, the message Unit PIN will be displayed on screen.
> Use the numeric keys to enter your PIN code.
The desired programme can now be viewed.
or
> Switch to a programme that is not blocked. If you have selected the setting Once under Point 9.3.1, the system will call for the PIN
code once when a blocked programme is selected. Thus, in order to make operation more comfortable for you, you need to enter the PIN code only once during each viewing session.
7.2.5 Infobox
Each time you change programmes, an information box will be displayed briefly, showing the programme slot and the programme name of the programme selected. In addition, other
programme properties will be indicated, such as for Videotext, for a 16:9 format broadcast, for encrypted programmes, for Dolby Digital broadcasts, for
subtitles, for Mono broadcasts. In addition a yellow bar will be displayed indicating the amount of time of that programme that has already elapsed. Also, EPGplus genres and any age restrictions will be displayed, if transmitted.
7.3 Receiving encrypted programmes
Your appliance is equipped with an integrated CONAX de-coding system as well as with a “Common Interface” for the recording of two CI modules. These can be used to receive encrypted Programmes. To do this you must first of all either insert a CONAX Smartcard into one of the two integrated card readers or plug in a CI module with a valid Smartcard into one of the two slots envisaged:
> Insert the CONAX Smartcard into a card slot of the integrated card-reader (golden
chip facing down and in the direction of insertion)
or
29
7
Page 54
> Insert a CI module in one of the slots.
> Insert the Smartcard in the card slot of the CI module. Ensure that the gold-coloured
chip of the Smartcard is on the upper surface, in the direction in which the card is inserted.
> If you now select an encrypted programme, the digital receiver will automatically
check the slot, and will display the programme in decoded form, provided the appropriate CI module, including a valid Smartcard, for this programme is inserted in the slot.
Special functions
Certain special functions are offered on specific programme slots, e.g. Premiere (reception only with a valid subscription!) For instance, multi-feed channels allow you to select various games in the sports category, i.e. different National League games in Germany, or you might be able to select different commentary tracks (e.g. stadium/broadcast), or in some cases different camera viewing angles may be available (e.g. Formula 1 racing). In addition, on some channels you may be able to select the starting time of a movie you have ordered. Please also note Point 7.16.7.2.
7.3.1 Option channels
Some programmes provide the opportunity of using so-called option channels. This function allows you, for instance, to select different camera perspectives in the case of a sports event (Formula 1) or to switch to different sporting venues (National League football in Germany). If a programme has option channels, this will be indicated by a note.
> To select one of the available options, press the key Option.
A selection window will be displayed, showing the various options available.
> Use the arrow keys up/down to select the desired option.
> Confirm by pressing OK.
7.3.2 Selecting a starting time
On some channels you have the option of selecting various starting times for viewing specific movies. These movies can thus be viewed around the clock, at specific starting times. Where a channel provides the facility of selecting starting times, this will be indicated.
> To select one of the available starting times, press the Option key.
A selection window will be displayed, showing the available starting times.
> Use the arrow keys up/down to select the desired starting time.
> Confirm by pressing OK.
The programme is validated for the starting time you have set, you can proceed to view this at the desired time.
7.3.3 Simultaneous reception of two encrypted programmes
Your receiver is able to receive two different encrypted programmes simultaneously, using only a single CI module and a single valid Smartcard. However, this is only possible when using a “Dual-Decrypt” compatible CI module (see specifications given by manufacturer of CI module), and then only if both desired programmes are located on the same transponder. Please also note the item CI Dual decoding in the Special functions Point 6.6.3.
30
7
Page 55
7.4 Volume control
You have the facility to adjust the volume of your digital receiver. This facilitates the easy operation of the receiver, as it means you have all the important functions on a single remote control, and will only rarely have to resort to using the remote control of the television set. When you switch on the digital receiver, sound will be reproduced at the volume level last set.
> To adjust the volume of your digital receiver, press Volume + to increase the
volume, and Volume - to decrease it.
> To switch the sound off (mute), press the key Sound on/off press the key again to
switch the sound on again
Please note:
The volume of the digital audio outputs cannot be adjusted.
7.5 Selecting a different language
If a programme is being broadcast in several languages, or with several audio channels, this will be indicated by a message displayed on screen. You can then proceed to set a different language or another audio channel as follows:
> Press the key Language selection.
A list indicating the languages currently being broadcast will appear on the screen.
> Use the arrow keys up/down to mark the desired language, and confirm by
pressing OK. You can now proceed to listen to the programme in the language selected. Your digital receiver is also capable of receiving mono Programmes.
> Use the arrow keys left/right to select Mono channel 1 ( ), Mono channel
2 ( ) or Stereo ( ).
7.5.1 Dolby Digital
If a programme is being broadcast in Dolby Digital Sound, this will be indicated when you switch to the programme, as the Dolby logo will be displayed in the Infobox. Provided you have enabled the Dolby Digital function in accordance with Point 6.3.6, the programme will automatically be reproduced in this sound format. If you have not turned on the Dolby Digital function then proceed as follows for manual Dolby Digital of your appliance:
> Press the key Language select.
If any are being broadcast, a list of the currently broadcast languages as well as Dolby Digital (AC 3) will be displayed on screen.
> Use the up/down arrow keys to mark the line Dolby Digital.
> Confirm by pressing OK. You can now listen to the programme in Dolby Digital sound. If you want your appliance to
automatically reproduce programmes in Dolby Digital then set you appliance, as described under point 6.3.6, for automatic Dolby Digital reproduction.
7.6 TV/Radio switching
The pre-programming includes both TV and radio Programmes.
31
7
Page 56
> Use theTV/Radio key to switch the digital receiver to radio mode.
The receiver will now switch to the last radio programme previously selected.
> Press the TV/Radio key again to return to the last television programme previously
selected
7.7 Return to last programme previously selected
> Press the Back key on the remote control to return to the last programme previously
selected.
> Press the key again to return to the programme previously selected.
7.8 Display clock and programme information
This function allows you to view programme information relating to the programme currently selected.
> Press the Info, key to display information for the currently selected programme. A display will appear on the lower half of the screen, showing the current time, the name of
the programme selected, the name of the current programme together with its start and stop times, whenever this information is broadcast by the programme provider.
7.9 Additional programme information
Wherever these are provided, you can use the function programme information to obtain additional programme information relating to the programme selected.
> By pressing the Info key twice, a further information window is opened, which
contains detailed information on the currently selected programme.
> Longer information text can be moved line-by-line using the up/down arrow keys
or page-by-page using the left/right arrow keys.
> Where available, pressing the Info key again will bring up the next programme.
> Press the Info key once again to switch off the display
7.10 Transponder information
> Call up the navigator by pressing OK.
> Use the arrow keys to mark the programme you wish to display.
> By pressing the yellow STATUS function key the data of the transponder which is
set will be displayed.
> In addition, you can use the coloured function keys to display Audio/Video
information, Program information, and, where available, information on the Encryption system (CA) in use.
> Press the Menu key to exit the information function
7.11 Freeze frame
> Press the Freeze frame key, and the current moving TV picture will be frozen, and
displayed as a still picture.
> Press this key again to return to normal operation.
32
7
Page 57
7.12 Videotext
7.12.1 Using the Videotext decoder of your television set
If transmitted, the Videotext is forwarded to your television set. To operate the videotext options, you must use the remote control of your television set. If there should be any problems related to the display on your television screen, such as an overlapping of videotext contents and picture, you should set your digital receiver to FBAS mode (Point
6.3.4).
7.12.2 Using the internal videotext decoder
As an alternative, you can also use the integrated TOP videotext decoder to display the information. When using TOP videotext, all text pages are split thematically into groups and blocks, which makes the videotext more readable.
> Switch to the channel for which you wish to see the videotext information.
> Switch Videotext on by pressing the Videotext key.
> Use the numeric keys to enter the desired videotext page. Your entry will be
displayed in the upper left-hand corner of the screen. Once you have entered the desired videotext page, the receiver will search for the page. As not all videotext pages can be transmitted simultaneously, it may take a few seconds for your receiver to find the page and display it on the television screen. All providers of videotext information use page 100 as their starting page.
> Use the red or the green key to move forward or backward one page at a time.
> Press the yellow function key to call up the videotext group indicated in the yellow
field.
> Press the blue function key to call up the videotext block indicated in the blue field.
7.12.2.1 Subpage display
Many Videotext pages consist of several subpages. This is indicated in the Videotext picture by two numbers separated by a forward slash (current subpage/number of subpages). As soon as a new subpage becomes available, it is automatically displayed.
> To display a particular subpage, press the OK key.
The column at the left-hand edge of the screen will become active. The already downloaded subpages will be displayed.
> Use the up/down arrow keys to select the desired subpage.
> Press the OK key to display the specific subpages.
7.12.2.2 Stop mode
> Press the Freeze frame key and the message “Stop” will be displayed in the upper
left corner of the videotext window. This will prevent automatic continuous paging through the videotext subpages.
> Press the Freeze frame key again to switch the stop mode off again.
7.12.2.3 Exit Videotext
> Press the Back key to return to normal operating mode.
33
7
Page 58
7.13 Subtitles
Where subtitles are broadcast, this will be indicated by the message Subtitle select. If you have switched on the function Subtitles (as per Point 6.4.2), these will be displayed automatically, provided that they are being broadcast in the language selected. If subtitles are being broadcast only in other languages, or are broadcast via videotext, you can switch these on manually as follows.
> Press the Option key, if necessary several times, until the entry Subtitles displays
a selection table listing the subtitle languages broadcast, and/or the videotext pages used to broadcast subtitles.
> Use the up/down arrow keys to mark the desired language or videotext page.
> Confirm by pressing OK.
The subtitles will now be displayed.
Please note that this function is only present when subtitles are actually being transmitted and this setting will not be kept after changing Programmes
7.14 PIP function (picture in picture)
Your receiver is equipped with a so-called PIP function. This allows you to view a second, smaller picture (PIP picture) within the larger main picture.
Call up PIP operation
> Switch “Picture in Picture” mode on by pressing the PIP key.
The current main picture, which can be sourced either from a TV programme or from a hard drive recording, will be displayed as a small (PIP) picture in the upper right corner, and the TV programme last viewed will be displayed as the main picture. The soundtrack of the main picture will always be reproduced when in PIP mode.
Please note: For technical reasons it is not possible two receive simultaneously two programmes which are transmitted in the HD format. Please also take into account point 6.5.3 (antenna signals).
In order to be able to use all of the possibilities of PIP operation of you receiver you should definitely be connected to two separate antenna supply lines. In that way the following reproduction combination become possible:
Main picture PIP image
34
7
Page 59
- to simultaneously reproduce two programmes (1 programme in HD format and 1 programme in SD format or 2 programmes in SD format) even if these are received from differing fields of reception.
- to reproduce a programme of your choice and simultaneously reproduce a hard drive recording of your choice.
If only one connector is available for an antenna supply line then the reproduction combinations will only be of limited availability.
- simultaneously reproduce two programmes (1 programme in HD format and 1 programme in SD format or 2 programmes in SD format) from the same reception field.
- reproduce any programme of your choice and simultaneously reproduce any hard drive recording of your choice
Change PIP pictures
> Press the Back key to exchange the two pictures. The PIP picture will be displayed
as the main picture, and vice versa.
Switch off PIP operation
> Switch “Picture in Picture” mode off by pressing the PIP key again.
The large main picture will be hidden and the small (PIP) picture will be displayed as the new main picture.
or
> Press the TV/Radio key. The small (PIP) picture will be hidden and the main picture
is displayed unchanged
7.15 Zoom picture
Using this function you can display 4:3 programmes on your 16:9 television set fully and true to the format. The same applies to 16:9 programmes, which are not transmitted signalised as such (no 16:9 symbol in the Infobox, see Point 7.2.5). Important prerequisites for this zoom function are, however, that the digital receiver is set to 16:9 operation according to Point
6.3.1 and your television set supports 16:9 signalisation over the scart socket.
> First press the Option key.
Sound selection will appear on the screen.
> With repeated pressure on the blue zoom function key various zoom factors can be
set.
> Exit Sound selection by pressing the Back key.
> Proceed in the same way to switch Zoom off. The zoom function stays switched on until you switch it off again or switch the unit to
standby.
7.16 EPGplus Electronic Programme Guide
Your digital receiver features an electronic programme guide. This allows you to display programme information related to one or more programmes on your screen. You can very quickly obtain an overview of the currently running programmes, the programmes of the day or those of the following days.
35
7
Page 60
The EPGplus functions allow you to:
- display information on programme contents on the screen
- display preview pictures of individual programmes
- mark specific programmes that will then be automatically switched on when the programme begins
- programme timers
- search for and select programmes by type of programme (genre).
7.16.1 Downloading EPGplus data
The programme information will be updated automatically by your receiver at the preselected updating time (Point 9.2.2), provided the receiver is in standby mode at the time. The downloading procedure will be indicated by the message Load EPG appearing in the display. The unit switches itself on at the preselected updating time in order to load the EPGplus data from the EPG channel data stream. The downloading process is indicated by Loading EPG in the display. If your unit is not in use at the time, this function will not be carried out. You can also start the download process manually directly after switching off (while the display is displaying Load EPG?) by pressing the EPG key. Load EPG appears in the display during the download process, as well as the percentage of EPGplus data already downloaded (e.g. 38%). The duration of the download process depends on the number of programmes to be downloaded. A maximum of seven days in advance can be displayed. As more programmes are added to the electronic programme guide, the volume of data increases, and the preview period is reduced correspondingly. It is up to you to decide which programmes should be listed in the electronic programme guide. These can be selected as described in Points 9.2.5 and 9.2.6.
7.16.2 Interrupting the download procedure
The downloading procedure can be interrupted by switching on the digital receiver (On/Standby key). The EPGplus data from the last update are then available.
7.16.3 Calling up the Electronic Programme Guide
> Press the EPG key on the remote control of the digital receiver. The Electronic
Programme Guide then appears on the screen.
If you have selected the starting category Overview (Point 9.2.3), the channels you have selected, or those of the factory default settings, will be shown with their current programmes (see also Point 9.2). You can now use the EPGplus function to find information on the content of the various Programmes. You can also use the EPGplus functions to select or mark the desired programme, or activate it in the Timer programming function.
7.16.4 Now (Table with current programme contents)
First the “Now” EPGplus table will be displayed, showing the programmes currently being broadcast. The yellow bar next to the programme name indicates the elapsed time of the current programme. The programme currently selected is marked.
> Use the up/down arrow keys to move the marker one line at a time.
36
7
Page 61
> Use the left/right arrow keys to move through the programme list one page at
a time. The EPGplus functions (Point 7.16.7) are now available.
> Pressing the yellow function key takes you to the “Next” EPGplus table (see Point
7.16.5)
or
> Press the TV/Radio key to return to normal operation.
7.16.5 Next
> You can call up the “Next” table (following programmes) by pressing the yellow
function key when the “Now” EPGplus table is displayed.
The EPGplus functions (Point 7.16.7) are available.
> Pressing the yellow function key takes you to the “More” EPGplus table (Point 7.16.6)
or
> pressing the green function key or the Back key will take you to the previous
Now” EPGplus table
or
> Press the TV/Radio key to return to normal operation.
7.16.6 More
> Pressing the yellow function key again when the “Next” EPGplus table is displayed
will cause the “More” EPGplus table to appear. An additional time window will appear in the headline of this table. The time of the displayed EPGplus table will appear in this time window.
> Press the yellow function key to skip forward to the time shown in the yellow-
coloured area.
> Keep the yellow function key pressed down to page through the information
continuously. A clock will be displayed to make the information more legible.
> Pressing the green function key takes you back through the tables.
The individual days of the week are displayed along the lower edge of the screen. If information is available for the following days, the appropriate fields will be marked.
> To view a preview for a specific day, use the numeric keys to enter the appropriate
number for the day required.
or
> Press the numeric key “0” to go to the PVR navigator.
> Press the Back key to return to the table “Next”.
7.16.7 EPGplus functions
To carry out the following EPGplus functions, call up EPGplus as described under Point
7.16.3.
7.16.7.1 EPGplus Info
You can use EPGplus Info to display detailed information and a picture relating to the marked programme. If detailed information is available, it is indicated by next to the
37
7
Page 62
corresponding programme. If there is a picture available, it is indicated by .
> Use the arrow keys or the function keys to mark the desired programme.
> Press the EPG key to display information and/or the picture relating to the
programme.
> Lengthy information text can be moved or paged through with the help of the arrow
keys.
> Press the Back key to return to the previous table.
7.16.7.2 EPGplus Timer programming
You can use the EPGplus Electronic Programme Guide to programme timer events easily. You can also use this function to programme the Timer for Multifeed programmes e.g. from the Premiere Sport Portal. Timer can only be programmed for Multifeed programmes in the EPGplus programme overview (see Point 7.16.7.3).
> Use the arrow keys or the function keys to mark the desired programme.
> Press the Record, key to programme a Hard drive Timer for the marked
programme (see Point 8.1.2).
or
> Press the Option key once to programme a Channel change timer for the
marked programme (see Point 8.1.2).
> Press the Option key once again to change the Timer type to a VCR timer.
or
> Press the red function key Timer to open a selection window.
> Use the up/down arrow keys to mark the desired Timer type (see Point 8.1.2).
> Confirm by pressing OK.
For control purposes the menu Managetimer will display the data relative to the selected programme. If necessary, you can effect any changes here (see 8.1.2).
> Press the Back key to return to the previous table.
The appropriate line is now marked. Depending on the Timer type, your receiver will now be switched on at the starting time of the selected programme. If the unit was switched on by the PVR Timer, this will be indicated by “PVR Timer” being shown in the display. In standby mode, the active Timer will be indicated by a clock symbol next to the time display.
Deleting the EPGplus timer event
> If you would like to cancel an EPGplus-programmed timer event, proceed as
described above to mark the corresponding programme.
> Press the red function key Timer to open a selection window.
> Use the up/down arrow keys to select the line Delete timer.
> Confirm by pressing OK.
or
> Delete a timer as described under Point 8.1.2.4.
Timer settings (pre- and post-run time)
With EPGplus Timer programming, the receiver obtains the data relating to the selected
38
7
Page 63
programme automatically from the EPGplus data. Both the starting and the ending time of the programme will be taken over correct to the nearest minute. However, it frequently happens that the selected programme starts a little earlier or a little later than scheduled. In this case the start or the end of the programme may be missing from the recording. To overcome this problem, you can enter a pre- or post-run time for the timer, in steps of one minute at a time. The timer will then start earlier and end later than given in the EPGplus data by the entered pre-run and post-run times.
> Press the red function key Timer to open a selection window.
> Use the arrow keys up/down to mark the line Timer settings.
> Confirm by pressing OK.
A menu will be displayed allowing you to enter the pre-and post-run times.
> Now use the arrow keys up/down to mark the line Timer pre-run time and
Timer post-run time.
> Use the numeric keys to enter the desired pre- or post-run time in minutes.
> Press the green function key Accept to save the setting and return to the previous
EPGplus table.
7.16.7.3 EPGplus programme overview
You can use the EPGplus programme overview to display a table with the whole day's listings for an individual channel. Proceed as follows:
> Press the EPG key.
If you have selected the start category Overview, see Point 9.2.3, the “Now” EPGplus table will appear.
> While the “Now” EPGplus table is displayed, press the green function key to switch
directly to the channel listings.
or
> press the blue function key EPG Menu.
> In the selection window, use the arrow keys up/down to mark the line
Programmes.
> Confirm by pressing OK.
The day’s overview of the selected channel will now be displayed.
> You can use the arrow keys to move the marker to the desired programme or time.
The individual days of the week are displayed along the lower edge of the screen. If information is available for the following days, the appropriate fields will be marked.
> To display the programme content of a specific day, press the corresponding
numeric key.
Displaying the EPGplus overview for other channels
> Press the yellow function key Programmes.
A list of EPGplus programmes will be displayed.
> You can now proceed to mark the desired channel using the arrow keys.
> Press the OK key to display the EPG overview of the marked channel.
7.16.7.4 EPGplus overview by type of programme (genre)
39
7
Page 64
If you are interested in specific types of programmes, you can have the programme information displayed by various genres, e.g. movies, news, etc.
> Press the EPG key to open the table “Now”.
> Press the blue function key EPG Menu to open a selection window.
> Use the arrow keys up/down to mark the line Genres and confirm by pressing
OK.
> Press the yellow function key Genres to open a window with the available types of
programme.
> Use the arrow keys to select the desired programme type and confirm by pressing
OK. The overview for the day will be displayed, listing only programmes of the type selected.
> Use the arrow keys up/down to move the marker to the desired programme.
> Use the arrow keys left/right to move through the list one page at a time. The
individual days of the week are displayed along the lower edge of the screen. If information is available for these days, the corresponding fields will be marked.
> To display the programme content of a specific day, press the corresponding
numeric key.
7.16.8 Ending EPGplus mode
> Press the Menu or the TV/Radio key to return to normal operation.
7.17 Sleep Timer
> Press the Sleep Timer key once or several times to set the switching-off time of the
receiver in the range of 15 minutes to 2 hours. At the end of the time selected the receiver will switch automatically to standby mode.
40
7
Page 65
8 Hard drive operation
Your PVR receiver (PVR=Personal Video Recorder) is equipped with an integrated hard disk drive. There is no provision for this drive to be exchanged other than by an authorised TechniSat retailer/technician. Due to the availability of the hard drive, you no longer require an external storage medium (e.g. a video recorder). The recording capacity is dependent on the size of the hard drive and on the volume of data of the broadcast material. Where these are available from the provider, the recording will include the actual audio and video data, as well as any subtitles, videotext data and additional sound channels broadcast. These can be called up when you play back the recording, as described in Points 7.5, 7.12 and 7.13.
8.1 Recording
Various recording modes are available for saving recordings to the hard drive.
1. Instant recording
Use this type of recording to record a currently running programme immediately, with just one press of the key.
2. Timer-controlled recording
In the case of this function, your digital receiver will be switched on and off for the recording, so this can be recorded in your absence. The timer can be programmed either manually or automatically using the EPG function.
3. Timeshift recording
The timeshift recording mode makes it possible to provide timeshift television viewing. While the programme is still being broadcast, you can already view the recording, shifted in time.
To utilise all the recording facilities of your receiver, you should ensure it is connected via two independent antenna connections. This allows you to use the following combinations of recording and playback:
- Record a programme and simultaneously reproduce another programme (1 programme in HD format and 1 programme in SD format or 2 programmes in SD format) or a recording of your choice from the hard disc.
- Simultaneously record two programmes (1 programme in DH format and 1 programme in SD format or 2 programmes in SD format) and reproduce a pre­recorded programme. of reception.
- Simultaneously record two programmes (even programmes from differing fields of reception, 1 programme in DH format and 1 programme in SD format or 2 programmes in SD format) and simultaneously reproduce a pre-recorded programme.
If only one antenna connection is available for connection to the receiver, only a limited range of recording and playback options is available.
- Record a programme and simultaneously reproduce another programme from the same field of reception (1 programme in HD format and 1 programme in SD format or 2 programmes in SD format) of reproduce a hard disc recording of your choice.
41
8
Page 66
- Simultaneously record 2 programmes from the same reception band (1 programme in HD format and 1 programme in SD format or 2 programmes in SD format) and reproduce a pre-recorded programme
8.1.1 Instant recording
Starting a recording manually
Option 1
> Switch on the channel on which the programme is being broadcast that you wish to record.
> Press the Record key to record the programme currently being broadcast. The
programme will continue to be displayed on screen while the recording is in progress.
> To interrupt the display of the current programme at a specific spot, press the yellow
function key Play/Pause. While the recording continues in the background, a still image (freeze frame) will be displayed on screen.
> To proceed with playing the programme from this spot, again press the yellow
function key Play/Pause. You will now view the programme shifted in time relative to the live broadcast (Timeshift), while the ongoing current programme will continue to be recorded in the background.
Option 2
> If you have to interrupt viewing a programme, e.g. because of a phone call, etc., you
can interrupt viewing of the programme by pressing the yellow function key Play/Pause, at the same time starting recording of the current programme. While the recording is started in the background, a still image appears on screen.
> To proceed with playing the programme from this spot, again press the yellow
function key Play/Pause. You will now view the programme shifted in time relative to the live broadcast (Timeshift), while the ongoing current programme will continue to be recorded in the background.
Ending a recording manually
> To end the recording procedure, first press OK.
> Now press the green function key to go to the PVR navigator.
> Use the arrow keys up/down to mark the current recording, and confirm by
pressing OK. The programme slot of the current recording will now be selected.
> Now press the green function key Stop.
A query will appear.
> Use the arrow keys up/down to select Save in order to save the recording on the hard
drive, or select Discard, in order not to save the programme, and confirm by pressing OK.
End recording automatically
Option 1
> Press the On/Standby key.
A query will now appear, asking what should be done with the current recording.
42
8
Page 67
> Use the arrow keys up/down to mark the line with the desired action.
> Confirm by pressing OK.
The receiver will record the whole programme and then go into standby mode.
> If you switch the receiver on before the end of the programme, a query will be
displayed, asking whether you wish to start the current programme at the
Beginning, or if you wish to continue viewing Live or if you wish to switch to the Current programme.
> Use the up/down arrow keys to mark the desired line and confirm with OK.
You select Beginning the recording will be continued in time-shift mode (Point
8.1.3).
Option 2
> Press the key Recording.
A window will then appear, showing the available functions.
> Use the arrow keys up/down to mark the line with the desired action, e.g.
+1 hour.
> Confirm by pressing OK.
The receiver will now record the programme(s) being broadcast on the channel selected for the time period selected, and will then automatically stop recording.
8.1.2 Timer recordings
You can record programmes on the integrated hard drive in your absence, using the hard drive timers. In addition, your receiver is equipped with video recorder timers and channel­switching timers. In terms of their programming, these Timer types differ only in name. During standby mode, hard drive and video recorder timers are indicated by a clock symbol. You can programme the timers manually as described in this chapter or using the EPGplus function as described under Point 7.16.7.2.
1. Hard drive timer
In the case of this function, your digital receiver will be switched on and off for the recording, so this can be recorded in your absence. If the unit was switched on by the hard drive timer, this will be indicated by “PVR Timer” in the display. Some of the remote control functions will be deactivated (e.g. calling up the main menu).
2. Video recorder timer
A video recorder timer is used to switch your digital receiver on and off for the selected programme in order to record it on an external recording unit, e.g. a video recorder, in your absence. Please note that you must programme your video recorder to record the programme. If the unit was switched on by the video recorder timer, this will be indicated by “ VCR Timer” in the display. Some of the remote control functions will be deactivated.
3. Channel-switching timer
If your unit is in normal operating mode, it will switch to the programmed channel slot at the set time. In contrast to the hard drive or video recorder timer options, the unit remains fully functional and is not switched off after the programme has finished.
43
8
Page 68
8.1.2.1 Manual programming of timer
> Use the Menu key to call up the Main menu.
> Use the arrow keys up/down to mark the line Manage timer.
> Confirm by pressing OK.
The sub-menu Manage Timer will be displayed.
> Use the arrow keys up/down to select the desired Timer type.
> Press the OK key to go to the entry window used for programming a new Timer
event.
Programme
> Use the arrow keys to mark the upper line of the menu.
> Press the OK key.
> In the selection window that is now displayed, use the arrow keys up/down to
select the desired source (TV or Radio).
> Confirm by pressing OK.
Now, depending on the previous setting, the TV resp. the radio programme list will be displayed.
> Now use the arrow keys to mark the desired programme.
> Use the arrow keys up/down to move around the list one line at a time.
> Use the arrow keys left/right to move backward or forward in the list one page at
a time.
> Press the OK key to accept this into the timer.
Date
> Use the arrow keys to mark the column Date.
> Use the numeric keys to enter the date (4-digit format) of the Timer event.
Start
> Use the arrow keys to mark the column Start.
> In this line, use the numeric keys to enter the starting time for the timer.
Stop
> Repeat the steps as described under “Start” to enter the stopping time (except for
channel-switching timer).
Repeat
> Use the arrow keys to mark the column Rep.
> Press the OK key.
A selection window will be displayed, showing various repeat options.
1x Timer on once
T Daily repeat
1 W Repeat once a week
1-5 Repeat only on weekdays
44
8
Page 69
6-7 Repeat only on weekdays
> Use the arrow keys up/down to select the desired function.
> Confirm and accept the setting by pressing OK.
Saving data to memory
> When you have completed the programming, press the green function key Accept,
to transfer the data to memory. If under Channel you have selected a channel that is blocked as per Point 9.3, you must first enter the PIN code before the data can be entered into memory.
> Press the TV/Radio key to return to normal operation.
8.1.2.2 Timer overview
The Timer overview function gives you an overview of all Timer events programmed.
> To go to the menu Timer overview, call up the menu Manage Timer as
described above.
> Use the arrow keys up/down to mark the line Timer overview.
> Confirm by pressing OK.
Should there by any overlapping in the programming of multiple Timer events, so that these timers cannot be executed correctly, these overlaps will be indicated in red.
8.1.2.3 Changing Timer programming
> To change an existing Timer setting, use the arrow keys up/down to mark the
Timer event you wish to change.
> Press the green function key Change to go to the settings of the marked timer.
Proceed to change these as described under Point 8.1.2.1.
> Use the arrow keys up/down to mark the additional field Type displayed.
> Confirm by pressing OK.
A window will be opened, listing the Timer types available.
> Use the arrow keys up/down to select the desired Timer type.
> To accept the Timer type, confirm by pressing OK.
> When you have completed the programming, press the green function key Accept
to store the data in memory.
8.1.2.4 Delete Timer programming
> Use the arrow keys up/down to delete an existing Timer setting.
> Press the yellow function key Delete.
A query message will be displayed: “Do you really want to delete this Timer?”
> Use the arrow keys left/right to select Yes .
> To delete the Timer entry, confirm by pressing OK.
8.1.2.5 Programming a new Timer event
> To programme a new Timer event, use the arrow keys up/down to mark a free
line in the menu Timer overview.
45
8
Page 70
> Press the green function key New to go to the entry window for programming a new
timer event. Now make your settings here in accordance with Point 8.1.2.1.
> Use the arrow keys up/down to mark the additional field Type displayed.
> Confirm by pressing OK.
A window will be opened, listing the Timer types available.
> Use the arrow keys up/down to select the desired Timer type.
> To accept the Timer type, confirm by pressing OK.
> When you have completed the programming, press the green function key Accept,
to transfer the data to memory.
Note!!!
Ensure that the receiver has acquired the correct time. This is shown in the display while the receiver is in standby mode. If this is not the case, switch the receiver to a major channel such as ZDF, etc. for approx. 30 seconds, to acquire the time.
8.1.3 Timeshift function
The time-shift function provides the facility of recording and playing back at the same time. This is made possible by Time-Shift television. Thus you can already view the beginning of the recording, and can decide to skip over certain passages already recorded (e.g. advert breaks). The live signal of the broadcast will continue being recorded at the same time (see the following examples).
Example: Time-shift playback
You have missed the start of the Formula 1 race. No problem! The PVR will show you the race at a time-shifted time while continuing to record the event .
Time
Recording
by PVR
Playback
by PVR
14:00 15:00 16:00 17:00 18:00 19:00
Start / Formula 1 / Stop
Start / Formula 1 / Stop
Example: Skipping advert breaks
Would you like to watch a programme without annoying advert breaks? The PVR lets you just skip over recorded advert breaks.
Time
Recording
by PVR
Playback
by PVR
14:00 15:00 16:00 17:00 18:00 19:00
Sen- dung
Programme
W
Progra
mme
Progra
mme
Progra
mme
Progra
mme
W W
W
Advert break
46
8
Page 71
> To go to a specific point in a currently running recording, you can use the
functions Play, Pause as well as Fast Wind and the Jogshuttle, as described in Point 8.2.
> Press the Info key to display the Infobox with a progress bar, showing the playing
and recording time elapsed.
8.1.4 Setting markers while recording
> Press the Record key to open a window showing the functions available.
> Use the arrow keys up/down to mark the line Set mark, confirm by pressing
OK. A marker will now be set at the current position. Continue in this manner to set markers at all desired places. Markers can also be set during Playback mode (Point
8.2.1.5) as well as in the menu Manage hard drive (Point 8.3.1.3).
8.2 Playback function
You can access hard drive recordings through the hard drive (PVR) navigator.
8.2.1 Playing back recordings
8.2.1.1 Reproducing hard drive recordings
> While in normal operating mode, press the green function key to open the PVR
navigator. Depending on whether you are in TV or radio mode, a list of all TV or radio recordings available on the hard drive will be displayed.
The marked recording will already be played back in the preview window.
> Use the arrow keys up/down to select the recording you wish to play.
> Confirm by pressing OK, to start the playback procedure. The message “Play ” will
be displayed briefly.
Recording information
> Call up the PVR navigator as described in Point 8.2.1.1.
> Using the arrow keys mark the recording on which you wish to access more
information.
> By pressing the yellow status function key the information on the market recording
will be faded in.
> Press the Return key to go back to the PVR navigator.
Recording a broadcast, and at the same time playing an existing recording
In addition, you can play an existing recording from the hard drive simultaneously with a new recording being stored.
> While a recording is in progress, call up the PVR navigator as described in Point
7.2.3.
> Use the arrow keys up/down to mark the recording you wish to play, and start the
47
8
Page 72
playback procedure by pressing OK.
8.2.1.2 Pause/Freeze frame
> To stop the playback of a recording (freeze frame) press the yellow function key or
the Freeze frame key while the playback is in progress. The message “Pause II” will be displayed.
> Press the respective key again to continue playback from the same spot.
8.2.1.3 Fast forward and rewind
To allow you to go to a specific point in a recording, your PVR provides fast forward and fast rewind functions.
> While in Play mode, press the blue function key Fast forward or the red function
key Rewind
The message “Fast forward ” or “Rewind ” will be displayed briefly. The
recording will now be played at 4 times speed in the desired direction.
> If you press the blue or red function key again, the speed will be increased to
16 times. The message “Fast forward ” or “Rewind ” will appear briefly.
> If you press the blue or red function keys yet again, the running speed will be
increased to 64 times. The message “Fast forward ” or “Rewind ” will appear briefly.
> By pressing the blue resp. red function key once more, you can scan forward or
backward through the recording in steps of 10 minutes.
> Once you have reached the desired spot in the recording, press the yellow function
key to go to normal viewing/playback mode.
8.2.1.4 Jogshuttle function
In addition, your receiver features a so-called jog-shuttle function, which allows you to go to a specific place in your recording very quickly and precisely. This can be used as follows:
> While in playback mode, press the key Jogshuttle on/off (Freeze frame),to go to
the jog-shuttle mode. The playback of the recording will be stopped (freeze frame/pause). The symbol “II” will be displayed.
Slow motion
> Press the arrow key right to view the recording in slow motion speed. The symbol
“I” will be displayed
Single frame progress
> Press the up arrow key or the down arrow key to display the next frame in a
forward direction or backward/reverse direction, respectively.
Fast forward and rewind
> Press the arrow keys left/right repeatedly to change the speed and the direction
of the playback. The various playback modes will be displayed as indicated in the table below.
48
8
Page 73
> Press the right or the left arrow key while  or  is displayed in order to
skip forward or back by 10 minutes.
Create Picture
> Press the Record key to store a single picture on the hard drive.
You can call up pictures created in this way as described under Point 8.2.3 and manage them as described under Point 8.3.2. To avoid picture errors/distortions, the picture should be taken from a freeze frame while “II” is displayed.
8.2.1.5 Setting markers
> Go as described above to the spot in your recording at which you would like to insert
a marker.
> Press the Record key to set a marker at the selected spot.
Continue in this manner to set markers at all desired places. Markers can also be set during Record mode (Point 8.1.4) as well as in the menu Manage hard drive (Point
8.3.1.3).
8.2.1.6 Jumping to markers
You also have the option in playback mode of going directly to those spots of the recording you have marked as per Point 8.1.4, 8.2.1.5 or 8.3.1.3.
> Press the Option key to open a window showing the available marks.
In addition, the mark “Current” will be shown. This designates the spot in the recording at which you have opened the window with the list of marks.
> As soon as you select a mark by using the arrow keys up/down, the recording
will be played from this spot.
> Press the OK key to close the window and switch to normal playback operation.
8.2.1.7 End playback session
> If you would like to end the playback session, press the green function key.
Playback mode will be ended, and the receiver will revert to normal operating mode. The receiver will automatically “remember” the exact spot of the recording at which you have ended playing it. The next time you start playing this recording, the receiver will automatically continue at the spot where you ended playing it the last time.
8.2.2 Playing MP3 files
Display Playback mode
Playback

Fast forward 4 speed

Fast forward 16 speed

Fast forward 64 speed

Rewind 4 speed

Rewind 16 speed

Rewind 64 speed
I
Slow motion
II
Pause
49
8
Page 74
8.2.2.1 On-screen controls
Your receiver is capable of playing files in MP3 format that have been stored on the hard drive or on a storage medium attached to the USB port. The USB device should be formatted using the file system FAT 32.Consult Point 8.3.2 on how to copy files from a USB device onto the hard drive.
> While in normal operating mode, press the green function key to open the PVR
navigator.
> By pressing the blue function key the NAV Menu opens a further window.
> Use the arrow keys up/down to mark the entry Music and confirm by pressing OK.
> Use the arrow keys up/down to select the source from which you wish to play
back the MP3 files, and confirm by pressing OK. A list of the MP3 files available on the hard drive or the USB device will appear.
These are indicated by the symbol . Folders located on the hard drive resp. on the USB device will be indicated by the symbol .
> Where appropriate, first use the arrow keys up/down to select the folder
containing the desired MP3 file, and confirm by pressing OK.
> Use the arrow keys up/down to select from the list the MP3 file you wish to play
first, and confirm by pressing OK.
The file selected will now be played. Thereafter the other files located on the same source medium, resp. in the folder selected, will be played automatically.
Skipping titles
> Press the arrow up/down key to skip to the next resp. the previous title.
Pause
> Press the yellow function key to stop the playback operation (Pause).
> Press the key again to resume playing the file from the position at which it was stopped.
Stop
> To stop the playback operation, press the green function key. You will return to
normal operating mode.
Switching folder levels
> During the reproduction operation press first of all the green Stop function key in
order to activate the Navigator again.
> To move from a folder to the next higher level, use the arrow keys to mark the
topmost line, which is indicated by the symbol , and confirm by pressing OK.
or
> press the Back key.
8.2.2.2 Display control
In order to avoid having to switch on the television set in order to be able to navigate an MP3 playback session, you can also control this via the display on the receiver front panel.
50
8
Page 75
An MP3file will be indicated on the display with its respective name, e.g. Sterne.mp3. A folder will be indicated by a display of square brackets, e.g. [Popmusic]. The hard drive will be displayed as hard drive and a USB device will be indicated as USB-device1, USB-device2 etc..
> While the receiver is in standby mode, press the Language select key. The
receiver will switch itself on, and will automatically call up the navigator in the Music category.
> Use the arrow keys up/down to select the source from which you wish to play
back the MP3 files, and confirm by pressing OK. No USB device is connected to the system, only the internal hard drive of the receiver will be available as a source.
> Where appropriate, first use the arrow keys up/down to select the folder
containing the desired MP3 file, and confirm by pressing OK.
> Use the arrow keys up/down to select from the list the MP3 file you wish to play
first, and confirm by pressing OK. The file selected will now be played. Thereafter the other files located on the same source medium, resp. in the folder selected, will be played automatically.
Skipping titles
> Press the arrow up/down key to skip to the next resp. the previous title.
Pause
> Press the yellow function key to stop the playback operation (Pause).
> Press the key again to resume playing the file from the position at which it was
stopped
Stop
> To stop the playback operation, press the green function key.
You will return to normal operating mode.
Switching folder levels
> During the reproduction operation press first of all the green Stop function key in
order to activate the Navigator again.
> In order to get out of a file one level higher mark the Back entry with the arrow
keys and confirm with OK.
or
> press the Back key.
8.2.2.3 MP3 playback modes
In addition to the regular playback mode, the following additional functions are available:
- Random play of all titles of the folder selected
- Repeating a title
- Repeat all titles of the folder selected
- Repeat all titles
> The various playback modes can be selected by means of the Option key or the
Language select key.
51
8
Page 76
The various modes are shown on screen resp. on the display panel as follows:
8.2.2.4 Playlist
To draw up a play list
You have the possibility of drawing up a playlist so that you have more convenient access to the replaying of MP3-files or radio recordings.
> While in normal operating mode, press the green function key to open the PVR navigator.
> By pressing the blue function key NAV Menu a further window will be opened.
> Use the arrow keys up/down to mark the entry Music and confirm by pressing OK.
> Use the arrow keys up/down to select the source from which you wish to play
back the MP3 files, and confirm by pressing OK. A list of the MP3 files available on the hard drive or the USB device will appear.
These are indicated by the symbol . Folders located on the hard drive resp. on the USB device will be indicated by the symbol .
> With the up/down arrow keys mark first of all the file which contains the MP3-files
which you want to add to the playlist and confirm with OK.
> With the up/down arrow keys select from the list the MP3-file which you want to
include into the playlist.
> Press the green function key PLS + to add the title to the playlist.
or
> With the up/down arrow keys mark a file which contains the MP3-files and press
the green function key PLS + in order to incorporate the complete contents of the file into the playlist.
In this manner you can draw up a playlist according to your wishes.
To display playlist
> While in normal operating mode, press the green function key to open the PVR
navigator.
> By pressing the blue function key NAV Menu a further window will be opened.
> Use the arrow keys up/down to mark the entry Music and confirm by pressing OK.
> Use the arrow keys up/down to select the source from which you wish to play
back the MP3 files, and confirm by pressing OK.
Function Display Screen
Repeat all titles
Directory
Normal playback of all titles of the folder selected
Directory
Random play of all titles of the folder selected
Random playback
Directory
Repeat current title
Title
52
8
Page 77
A list of the MP3 files available on the hard drive or the USB device will appear. These are indicated by the symbol . Folders located on the hard drive resp. on the USB device will be indicated by the symbol . You find yourself in the viewport.
> In order to change to the replay list viewport press the option key and mark the line
Replay Lists with the up/down arrow keys.
> Confirm by pressing OK.
Now all of the playlists contained in the storage medium will be displayed.
> Now use the up/down arrow keys to mark the playlist which you want to call up
and confirm with OK.
To delete titles from the playlist
> While in normal operating mode, press the green function key to open the PVR
navigator.
> By pressing the blue function key NAV Menu a further window will be opened.
> Use the arrow keys up/down to mark the entry Music and confirm by pressing
OK.
> With the up/down arrow keys select the source on which the appropriate playlist
exists and confirm with OK.
> In order to change to replay list viewport press the option key and with the
up/down arrow keys mark the replay list line.
> Now use the up/down arrow keys to mark the playlist which you want to edit.
> To delete a title from the playlist mark it with the arrow keys and press the green
function key PLS -.
To delete a playlist
> While in normal operating mode, press the green function key to open the PVR
navigator.
> By pressing the blue function key NAV Menu a further window will be opened.
> Use the arrow keys up/down to mark the entry Music and confirm by pressing
OK.
> With the up/down arrow keys mark the source in which the appropriate playlist exists
and confirm with OK. You are now in the viewport.
> Mark the playlist with the up/down arrow keys.
> By pressing the green function key PLS the complete playlist will be deleted.
8.2.3 Viewing pictures
You can display pictures created as described under Point 8.2.1.4, as well as data saved in JPG format on the hard drive or on a device connected to the USB port, using your receiver. The USB device should be formatted using the file system FAT 32. Consult Point 8.3.2 on how to copy files from a USB device onto the hard drive.
While in normal operating mode, press the green function key to open the PVR navigator.
> By pressing the blue function key NAV Menu a further window will be opened.
53
8
Page 78
> Use the up/down arrow keys to mark the line Pictures and confirm with OK.
> Use the arrow keys up/down to select the source from which you wish to view
the picture files, and confirm by pressing OK. A list showing the picture files available on the hard drive or on the USB device will be
displayed. These are indicated by the symbol . Folders located on the hard drive resp. on the USB device will be indicated by the symbol ..
> Where appropriate, first use the arrow keys up/down to mark the folder
containing the desired picture file, and confirm by pressing OK.
> Use the arrow keys up/down to select from the list the JPG file you wish to view,
and confirm by pressing OK. The picture selected will now be displayed in large format.
Show next/previous picture
> Press the arrow keys up/down to skip to the next or previous picture.
Rotate picture
> Press the blue or red function key to rotate the picture clockwise or
anticlockwise, respectively.
Stop
> To exit from picture viewing mode, press the green function key. You will return to
normal operating mode.
Switching folder levels
> While a picture is being displayed in large format, first press OK to activate the
navigator again.
> In order to get out of a file which is one level higher mark the top line which is marked
with the back-symbol with the arrow keys and confirm with OK.
8.2.3.1 Slide show
You can show pictures as a slide show. Via this function the pictures will be automatically shown on the screen one after another.
> By pressing the yellow slide show function key all the pictures in a file or a playlist
will be automatically reproduced one after another.
> To finish the slide show press the OK key and you will be returned to the Navigator.
8.2.3.2 Playlist
To draw up a playlist
You can draw up a playlist so as to make the design of the reproduction of image data more convenient.
> While in normal operating mode, press the green function key to open the PVR navigator.
> By pressing the blue function key NAV Menu a further window will be opened.
> Use the up/down arrow keys to mark the line Pictures and confirm with OK.
54
8
Page 79
> Use the arrow keys up/down to select the source from which you wish to view
the picture files, and confirm by pressing OK. A list showing the picture files available on the hard drive or on the USB device will be
displayed. These are indicated by the symbol . Folders located on the hard drive resp. on the USB device will be indicated by the symbol ..
> Using the up/down arrow keys mark first of all the file which contains the picture
file which you want to add to a play list and confirm with OK.
> Using the up/down arrow keys to select from the list the picture file which you
want to include in the playlist.
> Press the green function key PLS + to add the picture file to the playlist.
or
> Using the up/down arrow keys mark a file which contains the picture file and press
the green function key PLS + to include the complete contents of the file in the playlist.
In this way you can put together a playlist exactly according to your own wishes.
Replay lists
> While in normal operating mode, press the green function key to open the PVR navigator.
> By pressing the blue function key NAV Menu a further window will be opened.
> Use the up/down arrow keys to mark the line Pictures and confirm with OK.
> Use the arrow keys up/down to select the source from which you wish to view
the picture files, and confirm by pressing OK. A list showing the picture files available on the hard drive or on the USB device will be
displayed. These are indicated by the symbol . Folders located on the hard drive resp. on the USB device will be indicated by the symbol ..
> In order to change to the replay viewport press the option key and using the
up/down arrow keys mark the line Replay lists.
> Confirm by pressing OK.
Now all playlists contained in the storage medium will be displayed.
> Now using the up/down arrow keys mark the playlist which you want to see and
confirm with OK.
How to delete pictures from the playlist
> While in normal operating mode, press the green function key to open the PVR
navigator.
> By pressing the blue function key NAV Menu a further window will be opened.
> Use the up/down arrow keys to mark the line Pictures and confirm with OK.
> Use the up/down arrow keys to select the source in which the appropriate playlist
is situated and confirm with OK.
> In order to change to the replay list viewport press the option key and use the
up/down arrow keys to mark the line replay lists.
> Now use the up/down arrow keys to mark the playlist which you want to edit.
> To delete a picture from the playlist mark it with the arrow keys and press the
55
8
Page 80
green function key PLS -.
To delete a playlist
> While in normal operating mode, press the green function key to open the PVR
navigator.
> By pressing the blue function key NAV Menu a further window will be opened.
> Use the up/down arrow keys to mark the line Pictures and confirm with OK.
> Use the up/down arrow keys to select the source in which the appropriate playlist
is situated and confirm with OK. You are now in the file viewport.
> Use the up/down arrow keys to mark the playlist.
> By pressing the green function key PLS the complete playlist will be deleted.
8.3 Managing the hard drive
> Press the Menu key to call up the Main menu.
> Use the arrow keys up/down to mark the line Manage hard drive.
> Confirm by pressing OK.
The menu Manage hard drive will be displayed.
> Use the arrow keys up/down to move the marker within the menu and to change
the individual positions as indicated
8.3.1 Managing recordings
In this menu, you have the facility to manage your recordings.
> Press the OK key to go to the sub-menu Manage recordings.
A list of the recordings available on the hard drive will be displayed.
> Use the up/down arrow keys to mark the desired recording.
8.3.1.1 Delete
> To delete the marked recording, press the red function key Delete.
> Use the arrow keys left/right to mark the field OK and confirm by pressing OK
to actually delete the recording.
8.3.1.2 Parental control
You can block access to recordings that are not suitable for children or adolescents. These recordings can then only be played and viewed after the four-digit unit PIN code has been entered. The parental control function is only active if it has been switched on as described in Point 9.3.
> Press the green function key to block access to the marked recording. The recording
selected will be indicated as blocked by the parental control symbol.
8.3.1.3 Edit
> Press the yellow function key Edit to go to the menu that will allow you to edit the
marked hard drive recording.
The hard drive recording will be displayed in a preview window (1). In addition, the markers set in this recording (2) will be indicated. The markers Start and End are set
56
8
Page 81
as a standard feature. In addition, a yellow progress bar (3) will be displayed, showing the current playback position and the total duration of the recording.
> To skip to a marked spot of the recording, use the arrow keys up/down to mark
the desired marker, and confirm by pressing OK.
Going to any spot of the recording
> Use the coloured keys to go directly to various spots of your choice in the
recording.
Functions
> Press the green function key Menu to open a window showing the functions
available for editing the recordings.
> Use the arrow keys up/down to select the desired function, and confirm by
pressing OK.
Setting a marker
> Go as described above to the spot in your recording at which you would like to insert
a marker.
> Press the green function key Menu to open a window showing the functions
available.
> Use the arrow keys up/down to mark the line Set marker.
> Press the OK to set a marker at this spot of the recording.
Deleting a marker
> Use the arrow keys up/down to mark a marker you wish to delete.
> Press the green function key Menu to open a window showing the functions
available.
> Use the arrow keys up/down to mark the line Delete marker.
> Confirm by pressing OK to delete the marker.
Skip to marker
You can simply press a key to jump to a spot or spots in the recording that you have previously marked with a tag.
> Use the arrow keys up/down to select a mark to which you wish to jump.
> Press the green function key Menu and use the arrow keys up/down to mark
the line Jump to mark.
> To jump to this mark, confirm by pressing OK.
Renaming a marker
To name a mark, proceed as follows:
> Use the arrow keys up/down to mark a mark/tag that you wish to give a new
name.
> Press the green function key Menu and use the arrow keys up/down to mark
57
8
Page 82
the line rename mark.
> Confirm by pressing OK, to open the virtual keyboard, in order to enter a new name.
> Use the yellow function key to alternate between upper and lower case letters.
> Use the arrow keys to mark the first letter resp. the first symbol or figure if the
name you wish to enter.
> Confirm this by pressing OK.
The selected letter will now be displayed in the headline of the virtual keyboard.
> Now use the arrow keys to select the second letter of the name, and confirm this
by pressing OK.
> If you have entered an incorrect letter or symbol by mistake, you can delete this by
pressing the red function key.
> Enter the complete name in this way.
> To accept the name, press the green function key.
A message will be displayed, enquiring whether you really want to accept the name.
> Use the arrow keys to mark the field OK and accept the name by pressing OK.
> To exit from the virtual keyboard without accepting the entered name, press the blue
function key Abort.
Deleting a section
Your PVR provides the facility of removing whole sections or topics from an existing recording (e.g. unwanted advertising blocks).
Please note:
The deleted sections are irrevocably removed from the hard drive. To delete a section proceed as follows: Both the beginning and the end of the section that is to be removed must be marked by two marks/tags.
> To do this, mark the beginning and the end of the section to be removed with one
mark each as described under Setting a mark.
> Now use the arrow keys to set the mark that indicates the beginning of the section
that is to be removed. The section to be deleted is now highlighted in red (1) both on the progress indicator and in the overview of marks set.
> Now press the green function key Menu and use the arrow keys up/down to
mark the line Delete section.
> Press OK to display a query window.
> To actually delete the section, use the arrow keys left/right to mark the field OK
and confirm by pressing OK.
Extracting a section
This function allows you to copy a section of a recording. A new recording is generated, consisting only of this section. The recording from which this section is copied remains in memory unchanged. To extract a section, proceed as follows: The beginning and the end of the section that is to be copied must be indicated by two
58
8
Page 83
markers.
> To do this, mark the beginning and the end of the section to be removed with one
mark each as described under Setting a mark.
> Now use the arrow keys up/down to set the marker indicating the beginning of
the section to be copied. The section to be copied will now be indicated in red on the progress indicator as well as in the overview of existing markers (1).
> Now press the green function key Menu and use the arrow keys up/down to
mark the line extract section.
> Press OK to display a query window.
> To actually copy the section, use the arrow keys left/right to mark the field OK
and confirm by pressing OK. The marked section will now be copied to a new recording. Depending on the size of the section, this may take several minutes.
Splitting a recording
This function allows you where, for instance, two successive programmes were recorded as a single recording, to split these into two individual recordings. Each recording will be split at the point indicated by the relevant markers. Recordings can be split as follows:
> Set a marker at the beginning of the section to be separated, as described under set
marker.
> Now use the arrow keys up/down to mark the marker from which the total
recording is to be split.
> Now press the green function key Menu and use the arrow keys up/down to
mark the line split recording.
> Press OK to display a query window.
This will show information relating to the two recordings to be created by the split.
> To actually split the recording, use the arrow keys left/right to mark the field OK
and confirm by pressing OK.
Renaming a recording
Your PVR extracts information on the name of each programme broadcast from the broadcast data stream. If a recording includes several programmes, all the names of the recorded programmes will be noted, and recorded internally. To rename a recording, proceed as follows:
> Press the green function key Menu and use the arrow keys up/down to mark
the line Rename recording.
> Confirm by pressing OK.
A list with the available titles will be displayed.
> Use the arrow keys up/down to select the title you wish to use, and confirm by
pressing OK.
> A query will be displayed. Use the arrow keys left/right to mark the field OK and
confirm by pressing OK.
59
8
Page 84
> If you wish to give the recording a different, specific name, then use the arrow keys
up/down to mark the line New.
> If you press the OK key, the virtual keyboard will be displayed, and you can enter a
new name as described under Renaming a mark.
Enlarging a video
To make it easier getting to a specific point on a recording, you can enlarge the video picture of the recording.
> Press the green function key Menu and use the arrow keys up/down to mark
the line Enlarge video.
> Confirm by pressing OK to display the video picture in larger format.
> To again reduce the size of the video picture, proceed as above and mark the line
Reduce video.
8.3.2 Managing music/pictures
As described in Point 8.2.2. and 8.2.3, you can use your receiver to play music in MP3 format, and to view pictures in JPG format. To copy the appropriate files onto the hard drive, proceed as described in Point 4 to connect a USB device, on which the MP3 files resp. JPG files are stored, to the USB port of the receiver.
Please note,
you can only manage MP3 files in the Copy music menu and only JPG files in the Copy pictures menu
> Call up the menu Manage hard drive as described in point 8.3
> Use the arrow keys up/down to mark the line Copy music resp. Copy
pictures, in order to manage the appropriate files.
> Confirm by pressing OK.
or
A menu with two columns will be displayed, with the left half (set top box) showing the files and folders present on the hard drive. The column on the right (USB device) shows the files and folders stored on the USB device connected to the receiver.
> Use the green function key USB devices to switch to the USB device or the red
function key Set top box to switch to the hard drive. The first file resp. the first folder on the list will be marked.
60
8
Page 85
8.3.2.1 Copying
The Copy function will effect a copy of the marked file resp. folder to be stored on the hard drive, resp. the USB device. The original file resp. the original folder will remain unchanged.
> Use the arrow keys up/down to mark the file resp, the folder you wish to copy on
to the hard drive. resp. on to the USB device.
> Press the blue function key Functions to open a window showing the functions
available.
> Use the arrow keys up/down to mark the line Copy and confirm by pressing OK.
> To copy the marked file resp. the marked folder, now press the yellow function key
Copy. The marked file resp. the folder will now be copied, and the name will then also appear in the left-hand resp. right-hand column of the menu.
Marking blocks
To mark several files simultaneously, proceed as follows:
> Press the Press the OK key to go to the selection mode. The marked file will be
indicated by a cross on the left-hand side.
> You can now use the arrow keys up/down to also mark the preceding or the
following files.
> Once you have completed marking the desired files in this manner, press the yellow
function key Copy to copy the marked files on to the hard drive.
Please note that it is not possible to mark blocks of folders, only files!
8.3.2.2 Moving
The Moving function allows you to move or shift the marked file resp. the marked folder from the source medium (e.g. the USB device) to the target medium (e.g. the hard drive). At the end of this procedure, the file or folder that has been moved will be present only on the target medium, and will be deleted from the source medium.
> Use the red function key Set-Top-Box or the green function key USB devices
to go to the source on which the file or folder to be moved is currently stored.
> Use the arrow keys up/down to mark the file or the folder you wish to move.
> Press the blue function key Functions to open a window showing the available
functions.
> Use the arrow keys up/down to mark the line Move and confirm by pressing OK.
> To move the marked file resp. the marked folder, now press the yellow function key
Move.
> To move several files simultaneously, mark these as described in Marking blocks
above.
8.3.2.3 Delete
To delete files resp. folders proceed as follows:
> Use the red function key Set-Top-Box or the green function key USB devices
to switch to the source on which the file or folder to be deleted is located.
61
8
Page 86
> Use the arrow keys up/down to mark the file or folder you wish to delete.
> Press the blue function key Functions to open a window showing the functions
available.
> Use the arrow keys up/down to mark the line Delete and confirm by pressing
OK.
> To delete the marked file resp. the marked folder, you must now press the yellow
function key Delete. A query message will be displayed, asking whether you really wish to delete the selected files.
> Use the arrow keys left/right to mark the field Yes and confirm by pressing OK.
The data will now be deleted.
> To delete several files simultaneously, mark these as described in Marking blocks
above.
8.3.2.4 Sampling MP3 files/showing picture files
The function sample resp. show is available in this menu in order to sample an MP3file resp. to show a JPG file. This function can be called up as follows:
> Use the red function key Set-Top-Box or the green function key USB devices
to switch to the source on which the file is located that you wish to sample resp. to show.
> Use the arrow keys up/down to mark the file you wish to sample.
> Press the blue function key Functions to open a window showing the functions
available.
> Use the arrow keys up/down to mark the line Sample resp. Show and confirm
by pressing OK.
> Press the yellow function key. The marked file will now be played as a sample, resp.
shown.
8.3.3 Copying recordings
This function allows you to export recordings from the internal hard drive to an external USB device, e.g. another hard drive.
> Call up the menu Manage hard drive as described in Point 8.3.
> Use the arrow keys up/down to mark the line Copy recordings.
> Confirm by pressing OK.
The menu Copy recordings will be displayed.
On the left half of the screen you can see the recordings available on the internal hard drive. The right half of the screen shows the contents of the USB device.
8.3.3.1 Exporting
The Export function creates a copy of the marked file on the USB device. The original file remains intact.
> Use the arrow keys up/down to mark the file you wish to copy to the USB device.
> Press the blue function key Functions to open a window showing the functions
available.
62
8
Page 87
> Use the arrow keys up/down to mark the line Export and confirm by pressing OK.
> To copy the marked file, you must now press the yellow function key Export.
The marked file will now be copied to the USB device, and will then be displayed on the right half of the menu. Please note that this procedure may take quite some time, depending on the size of the file.
Marking blocks
To mark several files simultaneously, proceed as follows:
> Press the OK key to go to the selection mode.
The marked file will be indicated by a cross on the left-hand side.
> You can now use the arrow keys up/down to also mark the preceding or the
following files.
> Once you have completed marking the desired files in this manner, press the yellow
function key Export to copy the marked files on to the hard drive.
8.3.3.2 Preview
This function allows you to start the playback of a file in a small preview window.
> Use the arrow keys to mark the file you would like to preview.
> Press the blue function key Functions to open a window showing the functions
available.
> Use the arrow keys up/down to mark the line Preview and confirm by pressing
OK.
> To start the preview of the marked file, you must now press the yellow function key
Preview.
8.3.3.3 Delete
You can also delete a file on the internal hard drive resp. on the USB device while working in this menu.
> Use the red function key Set-Top-Box or the green function key USB devices to
switch to the source on which the file or folder to be deleted is located.
> Use the arrow keys up/down to mark the file or folder you wish to delete.
> Press the blue function key Functions to open a window listing the functions
available.
> Use the arrow keys up/down to mark the line Delete and confirm by pressing
OK.
> To delete the marked file resp. the marked folder, you must now press the yellow
function key Delete. A query message will be displayed, asking whether you really wish to delete the selected files.
> Use the arrow keys left/right to mark the field Yes and confirm by pressing OK.
Alternatively, select No and confirm by pressing OK in order to abort the procedure.
8.3.4 Hard drive information
> Press the OK key to display information on the integrated hard drive.
63
8
Page 88
8.3.5 Hard drive maintenance
> Press the OK key to obtain an overview of the number of recordings as well as the
degree to which the hard drive is filled with data.
8.3.5.1 Checking the hard drive
> To perform a check of the hard drive, use the arrow keys left/right to mark the
field Check.
> Press the OK key, then confirm the message displayed by pressing OK again to start
the procedure. The hard drive will now be checked. The result will be displayed once the procedure is completed.
8.3.5.2 Formatting the hard drive
When you format the hard drive, the file system will be replaced. This may become necessary, if an error has been found while checking your hard drive.
Note! All contents of the hard drive will be erased during formatting, all existing recordings and multi-media files (e.g. MP3’s) will be lost.
> To format the hard drive, use the arrow keys left/right to mark the field Format.
> Press the OK key, then confirm the message displayed by pressing OK again to start
the formatting procedure.
Please note!
The receiver may be operated only with the built-in hard drive supplied ex factory. The receiver may be damaged otherwise. Do not therefore open the unit housing and do not replace the hard drive yourself, otherwise all warranty claims will be void.
64
8
Page 89
9 Changing the basic programming
9.1 Configuring the Favourites list
This chapter describes how you may change the pre-programming of your digital receiver as well as the Favourites programme list in accordance with your preferences. This function is also required to sort new programmes into the list after a programme scan. To work with this function, you should know the following: your receiver features the Total list as well as four Favourites lists., provided the function enabling several Favourites lists has been switched on as per Point 6.6.1. The Favourites programme lists include all the programmes you have added as described below. The Total list includes all programmes/channels. This chapter also describes how you can delete programmes, how you can block access to them by means of the parental control function, or how you can add them to the EPG. If you press the OK key to display a programme list, the currently active Favourites programme list will be displayed.
9.1.1 Calling up the programme list manager
To edit the Favourites list, proceed as follows:
> Use the Menu key to call up the Main menu.
> Use the arrow keys up/down to mark the line Manage TV lists to work on the
TV list or Manage radio lists to work on the radio list.
> Confirm by pressing OK.
The programme list manager for the respective Favourites list (TV or radio list) will be displayed.
The Main Favourites list will be shown on the right half of the screen. This is now active, as the most recently selected programme of the Main Favourites list is marked. On the left half of the screen you will see the alphabetically sorted Total list. This Total list includes all available Programmes.
9.1.2 Select a Favourites list
> By pressing the green function key TV-main menu you can change from the
overall or the provider list to the favourites list.
> To select a favourites list press again on the green function key TV-main menu.
A window will be displayed, showing the lists available.
Please also note Point 6.6.1 of the operating manual.
> Use the arrow keys up/down to mark the Favourites list you wish to work on, and
confirm by pressing OK.
9.1.3 Select Total list
> Press the red function key to switch the marking to the Total list. This is now active.
> With renewed pressure on the red function key a selection window will appear. Here
you have the possibility of displaying the overall list sorted according to various selection criteria (e.g. all broadcasters, all free, all new, all found, all German, all English etc.) or sorted according to providers.
65
9
Page 90
> Using the up/down arrow keys select the desired programme lists (e.g.
languages).
> Confirm by pressing OK.
An additional selection window will now be opened.
> Now use the arrow keys up/down to mark the selection criterion you wish to
apply in sorting the Total list. Select, for instance, All German to display German­speaking broadcasters.
> Confirm by pressing OK.
Now the programme list will be displayed according to the selection previously made. Programmes which are already in the favourites list are marked with the appropriate favourites programmes place.
9.1.4 Adding programmes to the Favourites list
To add a programme from the Total list to one of the Favourites lists, call up the programme list manager as described in Point 9.1.1, where appropriate select the desired Favourites list, and change to the Total list.
> Press the blue function key Functions.
A selection window will be displayed, listing the available functions.
> Use the arrow keys up/down to mark the line Add.
> Confirm by pressing OK.
> Use the arrow keys up/down to mark a programme you wish to add to the list.
> Press the yellow function key Add to add the marked programme to the Favourites
list.
Marking blocks
To mark several programmes simultaneously, proceed as follows:
> Press the OK key to go to the selection mode.
The marked programme will be indicated by a cross on the left hand side.
> You can now use the arrow keys up/down to also mark the following or the
preceding programmes as well.
> When you have completed marking the desired programmes in this manner, press the
yellow function key Add to add the marked programmes to the Favourites list.
9.1.5 Deleting programmes
9.1.5.1 Removing (deleting) from the Favourites list
To remove programmes from the Favourites list, call up the programme list manager as described in Point 9.1.1. Where appropriate, you must still select the desired Favourites list.
> Press the blue function key Functions
A selection window will be displayed, listing the available functions.
> Use the arrow keys up/down to mark the line Remove.
> Confirm by pressing OK.
> Use the arrow keys up/down to mark a programme you wish to remove from the list.
> Press the yellow function key Remove.
66
9
Page 91
> To remove several programmes simultaneously, mark these as described in Point
9.1.4 (Marking blocks).
> When you have completed marking the desired programmes in this manner, press the
yellow function key Remove.
The programmes removed in this manner remain included in the Total list, and can be transferred back to the Favourites list at any time.
9.1.5.2 Deleting from the Total list
To remove programmes from the Total list, proceed as described under Point 9.1.5.1, but after calling up the programme list manager, press the red function key Total list to switch to the Total list and then select the function Delete. Before the programmes are deleted, however, the message will appear “Do you really want to delete the programm(s)?”.
> Use the arrow keys left/right to select Yes or No.
> Confirm the entry by pressing OK. Please note that programmes deleted from the Total list will also be deleted from all
Favourites lists.
9.1.6 Sorting programmes
To sort the order in which the programmes appear in your Favourites lists, call up the programme list manager as described in Point 9.1.1. Where appropriate, you can now select the desired Favourites list.
> Press the blue function key Functions.
A selection window will be displayed, showing the functions available.
> Use the arrow keys up/down to mark the line Sort.
> Confirm by pressing OK.
> Now use the arrow keys up/down to mark the programme you wish to place at
a different position in the list.
> Now press the yellow function key Sort.
A double arrow will be displayed next to the selected programme.
> You can now use either the arrow keys up/down and/or the numeric keys to
move the programme to the position in the list where you would like it to be placed.
> Press the yellow function key Sort. to store the programme at its new position.
> To sort several programmes simultaneously, mark these as described in Point 9.1.4
(Marking blocks).
> Now press the yellow function key Sort.
A double arrow will appear next to the selected programme block.
> You can now use the arrow keys up/down and/or the numeric keys to place
the marked programme block at the position in the programme list where you would like it to be.
> Press the yellow function key Sort to save the programme block at the new
position.
> When you have finished configuring the programme list according to your preferences
in this manner, press the Menu key to return to normal operation.
67
9
Page 92
9.2 Programming the electronic programme guide
Your receiver gives you the option of receiving a data channel with additional EPGplus data via ASTRA satellite systems (19.2° East). This data makes it possible to preview EPGplus information for up to a week.
> Use the Menu key to call up the Main menu.
> Use the arrow keys up/down to mark the line Setting.
> Confirm by pressing OK.
The sub-menu Settings will be displayed
> Use the arrow keys up/down to mark the line Programme guide.
> Confirm by pressing OK.
The menu Programme guide will be displayed.
> Use the arrow keys up/down to move the marker within the menu and to change
the individual positions as indicated. When selecting a menu item, please also note any messages displayed on screen.
9.2.1 Updating
> To receive the data channel, mark the line Updating.
> Press OK to select on.
If you do not wish to receive the additional data, or if reception is not possible at your location, data reception can also be switched off:
> To switch off, data reception, set the item Updating to off.
9.2.2 Updating time
> Use the numeric keys in the line Updating time to set the time when the
automatic download of the EPGplus data should take place.
9.2.3 Start category
The electronic programme guide offers various forms of displaying information (categories).
Overview
This form of display provides a quick overview of all channels included in the electronic programme guide.
Programmes
This form of display provides a table with the current day’s programmes of a single channel
Genres
If you are interested in specific types of programmes, you can have the programme information displayed according to specific genres, e.g. movies, news, sports, etc..
Last used
With this setting, the display type last used will be selected when EPGplus is called up.
> Press the OK key in the line Start category to open the list of the available start
categories.
> Use the up/down arrow keys to select the display type to be used when the
electronic programme guide is called up and confirm with OK.
68
9
Page 93
> If you select the start category Genres you can then also select the preferred genre
(e.g. film, news, shows, etc.) as described above.
9.2.4 EPG channel
> Press the OK key to call up the EPG channel submenu. If the parameters of the data channel required to load the EPGplus data have changed, you
can correct them in this menu. Current transponder data can be obtained from your retailer. Generally, under normal circumstances you should not make any changes in this menu.
9.2.5 Selecting TV channels/programmes
To obtain a better overview, you can programme the electronic programme guide EPGplus to contain only your favourite channels.
Please note:
The more channels you include in the electronic programme guide, the longer it takes to download the EPGplus data. The download time will also be increased if channels are selected for EPGplus for which no EPGplus data is available. Furthermore, it may no longer be possible to provide the maximum 7-day preview as the number of channels in the electronic programme guide increases.
> Press the OK key.
The Favourites list of TV channels will be displayed.
> Press the red function key to open a selection window.
Here you have the option of selecting the desired programme list type. You have the option of selecting the desired programme list type. You can also select on of the various Favourites lists. Refer also to Points 6.6.1 and 9.1.2.
> Using the up/down arrow keys select the type of programme list (e.g. favourites
lists).
> Confirm by pressing OK.
If the option of various Favourites lists was activated under Point 6.6.1, a selection window showing the various Favourites lists will be displayed.
> Confirm by pressing OK.
The selected programme list will be displayed.
> Use the arrow keys to mark a channel you wish to include in the electronic
programme guide.
> Press the yellow function key EPG to include the marked channel in the electronic
programme guide or to remove it from the programme guide.
> To include several channels in the electronic programme guide simultaneously, mark
these as described in 9.1.4 (Marking blocks).
> When you have completed marking the desired channels in this manner, press the
yellow function key EPG to accept the marked programmes into the electronic programme guide.
> Press the Menu key to return to normal operation. You can now start the downloading procedure manually:
> Switch the receiver off using the On/Standby key (Standby).
> Now, while the message “Load EPG?” is shown in the display, press the EPG key.
The receiver will now perform the download procedure. This will be shown by the
69
9
Page 94
message Loading EPG and an indication of the EPGplus data already downloaded in the display panel.
> The downloading procedure can be interrupted by switching the digital receiver on
(On/Standby key).
9.2.6 Selecting radio channels/programmes
Use the same procedure as described in Point 9.2.5 to include radio channels/stations in the programme guide.
Start update
> To download the EPGplus data, use the up/down arrow keys to mark the Start
download field and confirm with OK.
9.3 Parental control
Your receiver is equipped with a parental control function. This means that important functions (e.g. calling up the main menu) can be protected from unauthorised use. In addition, recordings and channels that you have blocked can only be accessed by entering a four-digit PIN code (unit PIN). To adjust settings in the menu Parental control proceed as follows:
> Use the Menu key to call up the Main menu.
> Use the arrow keys up/down to mark the line Settings.
> Confirm by pressing OK.
The sub-menu Settings will be displayed
> Use the arrow keys up/down to mark the line Parental control.
> Confirm by pressing OK.
The menu Parental control will be displayed.
> Use the arrow keys up/down to move the marker within the menu and to change
the individual positions as indicated. When selecting a menu item, please also note any messages displayed on screen.
9.3.1 PIN query mode
> In this line, use the arrow keys left/right to set the pin query mode of the
parental control function to Once or Never.
If you set the pin query mode to Once, and have not yet changed the PIN, you will be requested to change the PIN. To do this, proceed as described in Point 9.3.2.
Never
If you select the setting Never you will never be asked for the PIN. The parental control function is switched off.
Once
If you select the setting Once you will be asked to enter the PIN when calling up the main menu or when selecting a blocked channel resp. a blocked hard drive recording. To make matters more convenient for you, you will be asked for the PIN only once in each operating cycle.
9.3.2 Changing the PIN
The unit PIN code is set to 0000 at the factory.
> Press the OK key.
The menu for changing the unit PIN code will be displayed.
70
9
Page 95
> Now use the numeric keys to enter the current unit PIN code in the line Unit PIN
(factory setting 0000).
> In the line Enter new PIN use the numeric keys to enter the desired new unit
PIN code.
> Repeat the entry in the line Repeat new PIN.
> When you have completed changing the PIN code in this manner, you will be taken
back automatically to the menu Parental control.
Note!
Ensure that you do not forget the unit PIN code. If this does happen, please consult your retailer!
9.3.3 Selecting TV channels/programmes
> Press the OK key.
The TV Main Favourites list will be displayed. The programme currently selected is marked
> Press the red function key to open a selection window. Here you have the option of
selecting the desired programme list type. You have the option of selecting the desired programme list type. You can also select on of the various Favourites lists. Refer also to Points 6.6.1 and 9.1.2.
> Using the up/down arrow keys select the type of programme list (e.g. favourites lists).
> Confirm by pressing OK.
The option of various Favourites lists was activated under Point 6.6.1, a selection window showing the various Favourites lists will be displayed.
> Confirm by pressing OK.
The selected programme list will be displayed.
> Now use the arrow keys to mark the channel to which you wish to block access.
> Block the channel by pressing the yellow function key.
The parental control symbol will be displayed next to the programme selected.
> To block several channels simultaneously, mark these as described in 9.1.4 (Marking
blocks) and block access to them by pressing the yellow function key.
> When you have finished configuring the programme list according to your preferences
in this manner, press the Menu key to return to normal operation.
> To reverse the blocking of individual channels, proceed as described above to mark
the appropriate channel, and remove the parental control symbol by pressing the yellow function key.
9.3.4 Selecting radio channels/programmes
You can use the same method as described in Point 9.3.3 to block access to radio stations.
9.4 Programme search/scan
As mentioned above, your digital receiver is pre-programmed to receive from the ASTRA
19.2° East and EUTELSAT 13.0° East satellites. To receive new programmes, resp. the
programmes of other satellites, there are several options provided to perform a programme search, or scan.
71
9
Page 96
1. Automatic Scan
Select this type of search to scan all the satellites set in the menu Antenna settings (Point
6.4 and 10.4) for Programmes.
2. Satellite Scan
Select this type of search to scan only a specific selected satellite for Programmes.
3. Transponder Scan
Select this type of search to scan a specific transponder of a single satellite for Programmes.
4. Manual Scan
Select this type of search to search specifically for one particular programme, using the programme-specific PID numbers.
When the search has been completed, a message will appear on screen indicating how many programmes your digital receiver has found, how many of these are new programmes, and how many are encrypted Programmes. New programmes are saved in the Total list, and can then be transferred to the Favourites list in accordance with Point 9.1
> To commence searching for programmes, first call up the Main menu.
> Use the arrow keys up/down to mark the line Scan channels.
> Confirm by pressing OK.
The sub-menu Scan channels will be displayed.
> Now use the arrow keys up/down to select the type of scan you wish to perform,
and confirm by pressing OK.
9.4.1 Automatic scan
If this scan is selected, all the satellites listed in the menu Antenna settings (Point 6.4 and
10.4) will be scanned automatically for Programmes. You can decide whether you wish to
scan for all programmes (free-to-air and encrypted) or only for free-to-air Programmes.
> By pressing the OK key, decide whether you wish to scan only for free-to-air
programmes (Free programmes), or whether you wish to include encrypted programmes in the search (All programmes).
> Use the arrow keys up/down to mark the field Start search, and confirm by
pressing OK. Depending on the configuration of your antenna installation, a scan can take 15 minutes or more. Please also note Points 9.4.5 and 9.4.6 and the on-screen messages
9.4.2 Satellite scan
To scan a single satellite for programmes, select Satellite scan. Here you can decide whether you wish to scan for all (free-to-air and encrypted) programmes or only for free-to-air Programmes.
> Press the OK key again to open the selection table for the active satellites selected in
accordance with Points 6.4 and 10.4.
> Use the arrow keys up/down to mark the menu item All satellites, to scan all
active satellites for programmes, or mark the desired satellite to scan only this satellite for Programmes.
> Confirm by pressing OK.
72
9
Page 97
> Use the arrow keys up/down to mark the line Search mode.
> By pressing the OK key, decide whether you wish to scan only for free-to-air
programmes (Free programmes), or whether you wish to include encrypted programmes in the search (All programmes).
> Use the arrow keys up/down to mark the field Start search. Please also note
Points 9.4.5 and 9.4.6 and the on-screen messages.
9.4.3 Transponder scan
You can scan a specific transponder (see Point 11 Technical terms) for Programmes. To do this, you need to enter the transponder data.
Satellite
In this line you must enter the satellite on which the desired transponder is located.
> Use the arrow keys up/down to mark the line Satellite.
> Press the OK to display a table showing the active satellites, selected in accordance
with Points 6.4 and 10.4.
> Now use the arrow keys up/down to mark the desired satellite.
> Confirm by pressing OK.
The selected satellite will now be shown in the line Satellite.
Transponder frequency
> Use the arrow keys up/down to mark the line Transponder frequency.
> Use the numeric keys to enter the desired frequency in this line
Symbol rate
The symbol rate indicates the volume of data transmitted per second. This figure could be shown as, for example, 27500 (27500 symbols per second).
> Use the arrow keys up/down to mark the line Symbol rate.
> Use the numeric keys to enter the symbol rate.
Polarisation
> Use the arrow keys up/down to mark the line Polarisation.
> In this line, use the OK key to enter the polarisation plane (horizontal or vertical), on
which the desired transponder is broadcast. The signal strength and the signal quality of the transponder selected will be shown graphically at the bottom of the screen.
Search mode
> Use the arrow keys up/down to mark the line Search mode.
> By pressing the OK key, decide whether you wish to scan only for free-to-air
programmes (Free programmes), or whether you wish to include encrypted programmes in the search (All programmes).
> Using the up/down arrow keys subsequently mark the Search panel and
confirm with OK. The scan will be started. Please also note Points 9.4.5 and 9.4.6 and the on-screen messages.
73
9
Page 98
9.4.4 Manual search
Should a programme not be found in the course of an automatic search, a satellite search or a transponder search, it may be necessary to enter additional programme-specific PID numbers for this programme. You will need to obtain these numbers on the Internet, or possibly direct from the programme provider concerned. The menu differs from the menu Transponder search only with regard to the menu items PCR PID, Audio PID and Video PID. There is no need to enter the search mode.
> Proceed as described under Transponder search.
> Then use the arrow keys up/down to mark the lines PCR PID, Audio PID and
Video PID and use the numeric keys to enter the corresponding numbers.
> Use the up/down arrow keys to mark the Search panel and confirm with OK.
The scan will be started. Please note any messages displayed on screen.
If no programme is found as a result of the PID search, a query message will be displayed, asking whether this programme should be generated.
> If you wish to generate this programme, use the arrow keys left/right to select
the field Yes , and confirm by pressing OK. The programme will now be generated, and will be added at the end of the Favourites list
9.4.5 During the search
While the search is still in progress, you can follow the scanning of transponders on your screen. The following are shown: The satellite currently being scanned (1), the number of programmes found so far (2), the transponder last scanned (3), the last programmes found (4), the progress of the entire scan (5) and the transponder of the satellite currently being scanned (6).
> You can press the red function key to abort the search.
9.4.6 After the search
When the search has been completed, a message will appear on screen indicating how many programmes your digital receiver has found, how many of these are new programmes, and how many are encrypted Programmes. In addition, a query will be displayed, asking whether you wish to sort the programmes found into the TV or radio list automatically, or whether you want them to be added automatically at the end of the list, or whether you wish to sort them manually.
Automatic sorting
The programmes found will be sorted into the Main Favourites list in accordance with a pre­programmed list. The order of the programmes is determined by the audio language selected in Point 6.3.2 resp. by the country selected in Point 6.2.2.
Automatic addition
The newly found programmes are added to the end of the Main Favourites list in unsorted order.
Manual sorting TV/ manual sorting radio
Here you will go direct to the menu Manage TV lists red. Manage radio lists. Edit these lists as described under Point 9.1 of the operating manual.
74
9
Page 99
Back
The newly found programmes are not added to the Favourites list, and are retained only in the Total list.
> Use the arrow keys left/right to select the desired procedure.
> Confirm by pressing OK.
Please note any messages displayed on screen.
> Press the Menu key to return to normal operation
Independently of whether you have transferred the newly found programmes to the Favourites list automatically, these can at any time be added to the Favourites lists manually, as described in Point 9.1.
9.5 Service settings
You can at any time access the factory default settings. Also, you can, if the programme list has become obsolete through changes made by the programme providers, delete the programme list completely and perform a new programme scan. Please note that after performing the delete function you must first start a programme scan, and must then transfer the desired programmes from the Total list to the Favourites list.
> Use the Menu key to call up the Main menu.
> Now use the arrow keys up/down to mark the menu line Settings.
> Confirm by pressing OK.
The sub-menu Settings will be displayed
> Now use the arrow keys up/down to mark the line Service settings.
> Confirm by pressing OK.
The sub-menu Service settings will be displayed.
9.5.1 Activate factory default setting
If this function is called up, the factory default setting will be implemented, personal settings will be deleted, and the installation assistant AutoInstall will be started. Any data on the hard drive (recordings, MP3s, etc.) will be retained.
> Use the arrow keys up/down to mark the line Activate default setting.
> Press the OK key.
The query message will be displayed: “Do you really want to activate the default setting?”.
> Use the arrow keys left/right to select Yes or No
9.5.2 Delete all programmes
This function will delete all programme memory banks.
> Use the arrow keys up/down to mark the line Delete all Programmes.
> Press the OK key.
The query message will be displayed: “Do you really want to delete all programmes?”.
> Use the arrow keys left/right to select Yes or No.
> Confirm the entry by pressing OK.
75
9
Page 100
9.5.3 Updating the programme list (ISIPRO)
The ISIPRO programme list updating function ensures that the programme list of your receiver will automatically be kept up to date. To do this, a current programme list is broadcast at regular intervals via satellite (ASTRA 19,2° East) and is available to your receiver for downloading. Should the parameters for the data channel used to download the programme list have changed, you can correct them either in this menu or under Point 9.4.4 (manual programme scan. Current transponder data can be obtained from your retailer. Generally, under normal circumstances you should not make any changes in this menu.
> Press OK to go to the Update programme list submenu.
> In order for your receiver to check automatically whether a new programme list is
available, use the up/down arrow keys to mark the line Update.
> Switch the automatic programme list update on with the OK key.
ISIPRO channel
If the parameters of the data channel required for downloading the ISIPRO have changed, you can correct them in this menu as described under Point 9.4.4 (manual programme search). Current transponder data can be obtained from your retailer. Generally, under normal circumstances you should not make any changes in this menu.
Start availability test manually
> To check for the presence of a new programme list manually, press the yellow
function key Check. If a new programme list is available, a note will appear.
Start update
> To download the programme list, use the up/down arrow keys to mark the Start
update field and confirm with OK.
Your receiver will then re-start, and will indicate the availability of a new programme list by displaying a message on screen.
9.5.3.1 New programme list available
When the receiver is switched on, a new, available programme list will be indicated to you by a corresponding message, shown below.
9.5.3.2 Decline programme list
> If you do not wish to download the new programme list, press the red function key
Reject.
The message will only be displayed again when an even more up-to-date programme list is transmitted.
9.5.3.3 Update programme list automatically
If you would like to have the updating of changes in the programme list performed automatically, without any need for a manual procedure, then you should select this option. The changes will be implemented automatically. Newly found programmes will generally be added to the end of the Main Favourites list.
76
9
Loading...