Teac CT-M6828-S Service Manual
SERVICE MANUAL
Version 2- 68 cm CTV
Effective: MAY 2000 CTM6828V2SERV
TECHNICAL BULLETIN 26-Jun-00
MODEL:
PROBLEM:
CT-M5930S, CT-M6828S, CT-F683
RF Interference
File: CTM5830 6828 683 rf interf tb.doc
Some units of the first production lot for the models of reference have been supplied with a low quality RF lead
from the RF connector in the back panel to the tuner input. Those units may display diagonal interference lines
on the picture mainly in VHF bands.
Note that the braid of the good quality cable is very tight and totally covers the internal wire.
Instructions
Replaced the faulty RF cable assembly using the part number 40252200111.
Regards,
Alcides Berta
TEAC Australia Pty Ltd.
Page 1 of 1
TECHNICAL BULLETIN 12-July-2000
MODEL:
PROBLEM:
CT-F683, CT-M6828S, CT-M5930
I2C Mitsubishi chassis. Service Mode adjustments
File: CT-F683 CT-M6828 5930 RC tb.doc
The following information applies to all Great Wall models using I2C Mitsubishi technology. A
special type of remote control is necessary to access Service Mode adjustments, please refer to
the figure.
Accessing Service Mode
1- Press first button on the left of the FACTORY ON row (Button 1). The
word Key is visible on the screen.
2- Press FACTORY button (Button 2). The first page of factory
adjustments will be displayed.
3- Navigate between parameters and different pages using UP and
DOWN
buttons. Direct access to frequently used parameters is available from
dedicated buttons, for example
4- Adjust parameter values using
EW WIDTH, V AMPL
VALUE+
and
VALUE -
, etc.
.
Leaving Service Mode
1- Press first button on the left of the FACTORY ON row (Button 1). The
work Key is visible on the screen.
2- Press STANDBY button.
3- Turn POWER off from the front panel switch for at least 15 seconds.
Note:
The final version of remote control may be slightly different from the one used
to prepare this bulletin.
Regards,
Alcides Berta
TEAC Australia Pty Ltd.
Page 1 of 1
TECHNICAL BULLETIN 21-Jul-2000
MODEL:
PROBLEM:
CT-M6828S CT-F683 CT-M5930S
Audio noise
File: CT M6828S M5930S F683 noise tb.doc
A humming noise is audible at low volume from the speakers and particularly from the headphone
output (when available). The source of this noise is the vertical deflection circuit.
Instructions
1- Delete the jumper W286 on the main PCB next to CN111 in the fly-back transformer area.
2- Add a cable between the IF shielding can and the heat sink for the audio output IC.
Regards,
Alcides Berta
TEAC Australia Pty Ltd.
Page 1 of 1
TECHNICAL BULLETIN 11-August-2000
Wrong type
Correct type
MODEL:
PROBLEM:
CT-M6828S, CT-M5930 and CT-F683
Incorrect resistor type
File: CT-M6828S m oxide.doc
An incorrect resistor type has been fitted in position R504 of the neck board in some units. A
carbon film resistor having a light brown color body and mounted on the surface of the PCB can
eventually ignite and burn the board.
Instructions
Replace the carbon film resistor in location R504 with a metal oxide type. Separate the new
resistor from the surface of the PCB by approximately 10 mm.
Carbon film resistor
PN: 11347020512
47 Ohm, ½ W
Alcides Berta
TEAC Australia Pty Ltd.
Metal oxide resistor
PN: 11347020575
47 Ohm, ½ W
Page 1 of 1
Loading...