TEAC CTF-687 Service manual

SERVICE MANUAL

CTF687

68CM CTV

APR03 SERVCTF687

TEAC

SERVICE MANUAL

CT-F687

1. Caution……………………………………………………………2

2. Specification………………………………………………………6

3. BOM List…………………………………………………………13

4. Alignment Procedure………………………………………….…24

5. Block Diagram……………………………………………………29

6. Schematic Diagram………………………………………………30

7. PCB Layout………….……………………………………………31

8. Exploded V ie w Diagram………………………Temporary Absence

This manual is the latest at the time of printing, and does not
include the modifi ca tio n w hich ma y b e made after the pri nti ng, by
the consta nt improvement of product.

CAUTION:

Use of controls, adjustments or procedures other than those specified herein may result in
hazardous radiation exposure.

CAUTION: TO REDUCE THE RISK OF

CAUTION

RISK RISK OF OF ELECTRIELECTRICC

SHOCK SHOCK DO DO NOT NOT OPEN.OPEN.

The lighting flash with arrowhead symbol, with an equilateral triangle is intended to
alert the user to the presence of uninsulated voltage within the product s
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
the person.

The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.

ELECTRICAL SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.

dangerous

WARNING: TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT

EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

2

IMPORTANT SAFETY INSTRUCTIONS

CAUTION:

Read all of these instructions. Save these instructions for later use . Follow all Warnings and
Instructions marked on the audio equipment.

1. Read Instructions- All the safety and operating instructions should be read before the product is operated.

2. Retain Instructions- The safety and operating instructions should be retained for future reference.

3. Heed Warnings- All warnings on the product and in the operating instructions should be adhered to.

4. Follow Instructions- All operating and use instructions should be followed.

FOR YOUR PERSONAL SAFETY

1. When the power cord or plug is damaged or frayed, unplug this television set from the wall outlet and refer servicing to
qualified service personnel.

2. Do not overload wall outlets and extension cords as this can result in fire or electric shock.

3. Do not allow anything to rest on or roll over the power cord, and do not place the TV where power cord is subject to
traffic or abuse. This may result in a shock or fire hazard.

4. Do not attempt to service this television set yourself as opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified service personnel.

5. Never push objects of any kind into this television set through cabinet slots as they may touch dangerous voltage
points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the television set.

6. If the television set has been dropped or the cabinet has been damaged, unplug this television set from the wall outlet
and refer servicing to qualified service personnel.

7. If liquid has been spilled into the television set, unplug this television set from the wall outlet and refer servicing to
qualified service personnel.

8. Do not subject your television set to impact of any kind. Be particularly careful not to damage the picture tube surface.

9. Unplug this television set from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.

10.1. Do not place this television set on an unstable cart, stand, or table. The television set may fall, causing serious injury
to a child or an adult, and serious damage to the appliance. Use only with a car t or stand recommended by the
manufacturer, or sold with the television set. Wall or shelf mounting should follow the manufacturer s instructions, and
should use a mounting kit approved by the manufacturer.

10.2. An appliance and car t combination should be moved with care. Quick stops, excessive force, and uneven surfaces
may cause the appliance and cart combination to overturn.

3

PROTECTION AND LOCATION OF YOUR SET

11. Do not use this television set near water ... for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a

wet basement, or near a swimming pool, etc.
Never expose the set to rain or water. If the set has been exposed to rain or water, unplug the set from the wall
outlet and refer servicing to qualified service personnel.

12. Choose a place where light (artificial or sunlight) does not shine directly on the screen.

13. Avoid dusty places, since piling up of dust inside TV chassis may cause failure of the set when high humidity persists.

14. The set has slots, or openings in the cabinet for ventilation purposes, to provide reliable operation of the receiver, to
protect it from overheating. These openings must not be blocked or covered.

Never cover the slots or openings with cloth or other material.
Never block the bottom ventilation slots of the set by placing it on a bed, sofa, rug, etc.
Never place the set near or over a radiator or heat register.
Never place the set in enclosure, unless proper ventilation is provided.

a built-in

PROTECTION AND LOCATION OF YOUR SET

15.1. If an outside antenna is connected to the television set, be sure the antenna system is grounded so as to provide some

protection against voltage surges and built up static charges, Section 810 of the National Electrical Code, NFPA No.
70-1975, provides information with respect to proper grounding of the mast and supporting structure, grounding of the
lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection
to grounding electrode, and requirements for the grounding electrode.

EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE INSTRUCTIONS

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONALELECTRICAL CODE

ANTENNA
LEAD- INWIRE

GROUND CLAMP

ELECTRIC SERVICE

EQUIPMENT

NEC-NATIONALELECTRICAL CODE

ANTENNA DISCHARGE
UNIT (NEC SECTION
810-20)

GROUNDING
CONDUCTORS
(NECSECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PARTH)

15.2. Note to CATV system installer : (Only for the television set with CATV reception)

This reminder is provided to call the CATV system attention to Article 820-40 of the NEC that provides

installer s
guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as practical.

16. An outside antenna system should not be located in the vicinity of overhead power lines or other electric lights or power
circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care
should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

17. For added protection for this television set during a lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and disconnect the antenna. This will prevent damage due to lightning
and power-line surges.

4

OPERATION OF YOUR SET

18.

This television set should be operated only from the type of power source indicated on the marking label. If you are not
sure of the type of power supply at your home, consult your television dealer or local power company. For television
sets designed to operate from battery power, refer to the operating instructions.

19. If the television set does not operate normally by following the operating instructions, unplug this television set from the
wall outlet and refer servicing to qualified service personnel. Adjust only those controls that are covered in the operating
instructions as improper adjustment of other controls may result in damage and will often require extensive work by a
qualified technician to restore the television set to normal operation.

20. When going on a holiday : If your television set is to remain unused for a period of time, for instance, when you go on
a holiday, turn the television set and unplug the television set from the wall outlet.

off

IF THE SET DOES NOT OPERATE PROPERLY

21. If you are unable to restore normal operation by following the detailed procedure in your operating instructions,
do not attempt any further adjustment. Unplug the set and call your dealer or service technician.

22. Whenever the television set is damaged or fails, or a distinct change in performance indicates a need for
service, unplug the set and have it checked by a professional service technician.

23. It is normal for some TV sets to make occasional snapping or popping sounds, particularly when being
turned on or off. If the snapping or popping is continuous or frequent, unplug the set and consult your
dealer or service technician.

FOR SERVICE AND MODIFICATION

24. Do not use attachments not recommended by the television set manufacturer as they may cause hazards.

25. When replacement parts are required, be sure the service technician has used replacement parts specified
by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions
may result in fire, electric shock, or other hazards.

26. Upon completion of any service or repairs to the television set, ask the service technician to perform
routine safety checks to determine that the television is in safe operating condition.

5

PRODUCT SPECIFICATION

MODEL：：：： CT-F687

AMBIENT CONDITIONS：

AMBIENT TEMPERATURE：

OPERATING ：：：：-10°°°°C ~ +40°°°°C

STORAGE ：：：：-15°°°°C ~ +45°°°°C

HUMIDITY

OPERATING：＜

STORAGE: ＜＜＜＜90%

AIR PRESSURE: 86kpa ~ 106kpa

PREPARED BY : DATE:

：

：：

：

：：

：＜80%

：＜：＜

APPROVED BY: DATE:

6

A: GENERAL SPECIFICATION :
1: CRT
14” 20”
21” 25”
XX

29” 34” OTHER

2: CHASSIS:
DIGITAL

SURROUND SOUND TELETEXT XX

S.VHS OTHER

XX

NICAM STEREO XX

ANALOG

GERMAN STEREO

3: CPU:

TSB M5C01 TSB M5C03 TSB M5ENG TSB M6/M6A TSB M7/M7A
TSB M8A TSB M8B TSB CTS-654A TSB M2A SS M4F

PHIL.CTV 222S MIT.(2911) SIE SDA 5352 XX

其他(OTHERS) M13

4: TV BROADCASTING SYSTEM AND COUNTRY

PAL-I XX
PAL-DK.BG SECAM-BG SECAM-L SECAM-DK.BG

PAL-N NTSC-M XX

PAL-BG PAL-DK PAL-DK.1

NTSC3.579/4.43 AV MODE 21 MULTI SYSTEM

UK HK GERMAN RUSSIA

CHINA USA E.EUROPE VIETNAM

CANADA DUBAI INDONESIA S.AFRICA

MALAYSIA MID. AMERICA SINGAPORE

XX

AUSTRALIA & NEW ZEALAND TAIWAN MOROCCO

PHILIPPINES

OTHER

ISRAEL

5： RECEIVING CHANNELS

CH21--CH69 CH2--CH12（CCIR）

CHFA-CHS20（FRANCE BAND） CH2--CHS41（HYPER BAND）
CH21--CH69 CH21--CH69
CH2--CHS20（CABLE BAND） CH2--CH13（USA BAND）

7

CH21--CH69 CH14--CH83
CHR1--CHR12（OIRT） CH1--CH12/CH13-CH57（CHINA BAND）

XX

OTHER CATV 470MHz

6： SCANNING LINES AND FREQUENCIES
625 LINES 15.625kHz 50Hz

525 LINES 15.75kHz 60Hz
XX

525/625 LINES 15.625kHz /15.75kHz 50/60Hz

7： COLOUR SUB-CARRIER

X

4.433MHz

X

X

3.579MHz

X

3.58MHz

8： INTERMEDIATE FREQUENCIES
PICTURE 39.5MHz

XX

PICTURE 38.9MHz XX

PICTURE 38.0MHz

SOUND 6.0MHz
SOUND5.5MHz

SOUND 6.5MHz
PICTURE 45.75MHz SOUND 4.5MHz
OTHER AM SOUND 6.5MHz
9： POWER CONSUMPTION ：

65W 70W 75W 80W 110W 120W

130W 140W 180W 190W OTHER

XX

10： POWER SOURCE ：
AC 120V 60Hz±10％
AC 200V 50Hz±10％
AC 220V 50Hz±10％

AC 220V 50Hz+10％~25％

XX

AC 240V 50Hz±10％

AC 110V-240V 50/60Hz±10％

OTHER

11： AUDIO OUTPUT POWER (7％THD)

8

13”& 14”---1W

20”& 21”---2W

20”& 21”---2W + 2W (R + L)

25”---4W + 4W (R + L)

XX

29” >=6W + 6W (R + L)

34”---8W + 8W(R + L)
OTHER
12： AERIAL INPUT IMPEDANCE

XX

75 Ω UNBALANCED DIN JACK ANT.INPUT75
75Ω UNBALANCED F TYPE ANT.INPUT FOR NTSC
300 Ω BALANCED（TWO TERMINALS ANT.INPUT）
OTHER
13： PRODUCT SAFETY REQUIREMENT
BS APPROVAL

VDE APPROVAL
UL APPROVAL

CHINA APPROVAL
XX

CB APPORVAL
XX

OTHER SAA EMC

14： PRODUCT EMC/EMI REQUIREMENT

FTZ APPOVAL
FCC APPROVAL
XX

CHINA APPOVAL
OTHER
B： BASIC FEATURES OF CONTROLLER

1： CHANNEL TUNING METHOD

X

VOLTAGE SYNTHESIZER (V.S.)

X

9

PLL FREQUENCY SYNTHESIZER (F.S.)
2： PRESETTABLE PROGRAM
50 PROGRAMS
XX

100 PROGRAMS 181 PROGRAMS

0-99 PROGRAMS

OTHER
3： TUNING FOR VHF AND UHF BANDS

XX

AUTO SEARCH） XX

FINE TUNING

XX

MANUAL TUNING）

4： PICTURE AND SOUND ADJUSTMENT

X

BRIGHT，CONTRAST，COLOUR AND VOLUME CONTROL

X

XX

TINT CONTROL(NTSC)

TREBLE，BASS，BALANCE CONTROL

XX

SHARPNESS CONTROL
XX

OTHER 4D FAULT SOUND STETTING, FIVE-BAND EQUALIZER

5： TELETEXT
SIMPLE TEXT TOP(TABLE OF PAGES)

FLOF (FASTEXT) LIST
6： ON SCREEN DISPLAY
XX

GENERAL FEATURES∗ STEREO DUAL LAN.

FOUR S.EFFECT INDICATOR GERMAN STEREO INDICATOR

注： ∗REMARK：OSD-GENERAL FEATURES OF CPU：
VOLUME，BRIGHTNESS，CONTRAST，COLOUR，PROGRAM，BAND，

AUTO SEARCH，MANUAL，TUNE，MUTING，AV AND SLEEP TIMER．

7： SLEEP TIMER

XX

10-120 MINUTES WITH 10M.INCREMENT

8：AUTO OFF WHEN NO BROADCASTING SIGNAL

10 min XX

15 min 20 min

10

9： FULL FUNCTION INFRARED REMOTE CONTROL
P/N OF REMOTE CONTROL INLAY) : 58-HS46F2-MUI
10： REMOTE EFFECTIVE DISTANCE 8 m

C： CONSTRUCTION OF FRONT PANEL

XX

MAIN POWER SWITCH FUNCTION SELECT

XX

REMOTE SENSOR XX

MENU SELECT
SYSTEM FUNCTION S.VHS INPUT
MICROPHONE INPUT XX
XX

STANDBY INDICATOR XX

BAND SELECT XX

TV/AV SELECT

PROGRAM VOLUME UP/DOMN

RCA SOCKET (SIDE)

EARPHONE INPUT OTHER
AUTO SEARCH AND MANUAL TUNING SELECT
D： CONSTRUCTION OF REAR PANEL

XX

75Ω AERIAL TERMINAL

300Ω AERIAL TERMINAL
RCA SOCKET(AV INPUT ONLY
RCA SOCKET--AV IN/OUT

RCA SOCKET --A-R+L IN/OUT，V- IN/OUT

XX

RCA SOCKET --A-R+L /V INPUT X 2，

SCART SOCKET
XX

S.VHS INPUT
EXT/INT SPEAKER SELECT
EXT.SPEAKERS（R+L）TERMINALS

EXT.SPEAKERS（R+L）RCA SOCKET
SUPER WOOFER TERMINAL

X

OTHER YUV

X

E： AUDIO AND VIDEO INPUT/OUTPUT

11

XX

RCA SOCKET

SCART SOCKET(AV)
S SCART SOCKET(FULL)

SPECIFICATION SCART RCA
VIDEO INPUT 75Ω S
AUDIO INPUT 10kΩ (R+L)
VIDEO OUTPUT 75Ω
AUDIO OUTPUT 1kΩ (R+L)
RGB INTPUT 75Ω
AUDIO LINE OUTPUT 1kΩ

F： OTHERS INFORMATION

1. FLYBACK ： 37-BSC290-1650X

2. TUNER ： 07-389VI5-NX4

3. SAW FILTER ： 45-SAWK33-50K

1V

P-P

0.5V

1V

P-P

0.5V

0.7V

1V

P-P

rmS

rmS

P-P

1V

P-P

0.5V

1V

P-P

0.5V

rmS

rmS

4. POWER CORD ：

5. FUSE ：

6. COLOUR TEMP ：

7. MAGNETIC FIELD ：

8. IC EEPROM ： 13-00M24C-08P

9. IR RECEIVER ： 11-IRR001-1X0

10. CIRCUIT DIAGRAM ： 01-29274T-MA3

11. MAIN BOARD ： 40-2916MT-MAH

12

Sheet1

R936, R938

R053, R056, R205, R206, R917, R918

03-29274T-AA3 Effective Date : 2002-8-30
Parent Item Parent Item Description Item No. Item Description

08-29274T-MAN ASS'Y - MAIN BD 27-MBC104-J0X CAP. M.P.E.0.1 UF 50V +/-5% C 6 C102, C211, C212, C213, C242, C252
08-29274T-MAN ASS'Y - MAIN BD 27-PBC222-J0X CAP. P.E. 2200 PF 50V +/-5% C 2 C207, C221
08-29274T-MAN ASS'Y - MAIN BD 27-PBC223-J0X CAP. P.E. 0.022UF 50V +/-5% C 2 C611, C612
08-29274T-MAN ASS'Y - MAIN BD 27-PBC333-J0X CAP. P.E 0.033UF 50V +/-5% C 1 C302
08-29274T-MAN ASS'Y - MAIN BD 27-PBC393-J0X CAP. P.E 0.039UF 50V +/-5% C 1 C308
08-29274T-MAN ASS'Y - MAIN BD 27-PBC472-J0X CAP. P.E. 4700PF 50V +/-5% C 1 C244
08-29274T-MAN ASS'Y - MAIN BD 27-PBC563-J0X CAP. P.E 0.056 UF 50V +/-5% C 1 C304
08-29274T-MAN ASS'Y - MAIN BD 27-RHQ563-J0X CAP. PP 0.056 UF 400V +/-5% C 1 C451
08-29274T-MAN ASS'Y - MAIN BD 34-R120J2-0EX COIL PL - 12 UH +/-5% C 1 L256
08-29274T-MAN ASS'Y - MAIN BD 18-CB0393-JNX RES. C.F. 39K OHM 1/6W +/-5% C 1 R314
08-29274T-MAN ASS'Y - MAIN BD 18-CD0392-JNX RES. C.F. 3.9K OHM 1/4W +/-5% C 1 R312
08-29274T-MAN ASS'Y - MAIN BD 18-FG0479-JHX RES. M.O. 4.7 OHM 2W +/-5% C 1 R303
08-29274T-MAN ASS'Y - MAIN BD 27-ALQ392-J0X CAP. M.PP 3900PF 1.6KV +/-5% C 1 C415
08-29274T-MAN ASS'Y - MAIN BD 27-RHQ223-J0X CAP. PP 0.022 UF 400V +/-5% C 1 C416
08-29274T-MAN ASS'Y - MAIN BD 36-LIN210-XX1 COIL LINEARITY 21 UH C 1 L413
08-29274T-MAN ASS'Y - MAIN BD 36-WID801-XX1 COIL WIDTH 800 UH C 1 L414
08-29274T-MAN ASS'Y - MAIN BD 70-271510-00A SERVICE CARD C 1 FOR PRODUCTION USE
08-29274T-MAN ASS'Y - MAIN BD 18-CD0681-JNX RES. C.F. 680 OHM 1/4W +/-5% C 1 R724
08-29274T-MAN ASS'Y - MAIN BD 18-CD0272-JNX RES. C.F. 2.7K OHM 1/4W +/-5% C 2 J691, R313
08-29274T-MAN ASS'Y - MAIN BD 18-CD0472-JNX RES. C.F. 4.7K OHM 1/4W +/-5% C 1 R725
08-29274T-MAN ASS'Y - MAIN BD 18-CE0222-JNX RES. C.F. 2.2K OHM 1/2W +/-5% C 1 R309
08-29274T-MAN ASS'Y - MAIN BD 27-AHR434-J0X CAP. M.PP 0.43 UF 400V +/-5% C 1 C418
08-29274T-MAN ASS'Y - MAIN BD 27-ALQ272-J0X CAP. M.PP 0.0027UF 1.6KV +/-5% C 1 C413
08-29274T-MAN ASS'Y - MAIN BD 27-ALR103-J0X CAP. M.PP 0.01 UF 1.6KV +/-5% C 1 C414
08-29274T-MAN ASS'Y - MAIN BD 40-2916MT-MAH P.C.B. MAIN BD C 1
08-29274T-MAN ASS'Y - MAIN BD 62-2927MB-1UN MAIN BD BRACKET C 1

08-29274T-MAN ASS'Y - MAIN BD 46-12866W-02X PIN BASE *2 S11-02W C 1 P601
08-29274T-MAN ASS'Y - MAIN BD 18-EG0399-JHX RES. FUS. 3.9 OHM 2W +/-5% C 1 R461
08-29274T-MAN ASS'Y - MAIN BD 62-313410-0HA BRACKET C 1
08-29274T-MAN ASS'Y - MAIN BD 63-W30120-AB4 S/T SCREW W 3 X 12 AB C 1 MTG FBT BKT & M.BD BKT
08-29274T-MAN ASS'Y - MAIN BD 18-CB0822-JNX RES. C.F. 8.2K OHM 1/6W +/-5% C 1 R286
08-29274T-MAN ASS'Y - MAIN BD 18-FG0100-JHX RES. M.O. 10 OHM 2W +/-5% C 1 J211
08-29274T-MAN ASS'Y - MAIN BD 25-BCA102-M1X CAP. ELEC 1000 UF 16V +/-20% C 1 C846
08-29274T-MAN ASS'Y - MAIN BD 66-343730-0B0 HOLLOW RIVET 1.6X3.0XL3.2 C 5 FOR T461
08-29274T-MAN ASS'Y - MAIN BD 13-000040-52P IC 4052 H 2 IC961, IC962
08-29274T-MAN ASS'Y - MAIN BD 13-0TDA26-16S IC TDA2616 (AUDIO O/P) H 1 IC601
08-29274T-MAN ASS'Y - MAIN BD 13-TB1240-ANP IC TB1240AN H 1 IC201

08-29274T-MAN ASS'Y - MAIN BD 18-CB0102-JNX RES. C.F. 1K OHM 1/6W +/-5% C 25

08-29274T-MAN ASS'Y - MAIN BD 18-CB0104-JNX RES. C.F. 100K OHM 1/6W +/-5% C 13
08-29274T-MAN ASS'Y - MAIN BD 18-CB0106-JNX RES. C.F. 10M OHM 1/6W +/-5% C 1 R116
08-29274T-MAN ASS'Y - MAIN BD 18-CB0123-JNX RES. C.F. 12K OHM 1/6W +/-5% C 2 R244, R951
08-29274T-MAN ASS'Y - MAIN BD 18-CB0151-JNX RES. C.F. 150 OHM 1/6W +/-5% C 4 R127, R934, R935, R994

Item

Quantity

Type

Req. Designator

R062, R067, R071, R091, R124, R220,
R243, R269, R271, R301, R304, R451,
R911, R912, R921, R922

R919, R926, R927, R928, R929, R973,
R983

FOR FRONT
CAB. (SPK)

,
R939, R945,
R946, R947,
R948, R966, R968

,

13

Sheet1

08-29274T-MAN ASS'Y - MAIN BD 18-CB0152-JNX RES. C.F. 1.5K OHM 1/6W +/-5% C 5 R063, R204, R212, R213, R214
08-29274T-MAN ASS'Y - MAIN BD 18-CB0181-JNX RES. C.F. 180 OHM 1/6W +/-5% C 1 R123
08-29274T-MAN ASS'Y - MAIN BD 18-CB0182-JNX RES. C.F. 1.8K OHM 1/6W +/-5% C 1 R715

08-29274T-MAN ASS'Y - MAIN BD 18-CB0221-JNX RES. C.F. 220 OHM 1/6W +/-5% C 8
08-29274T-MAN ASS'Y - MAIN BD 18-CB0224-JNX RES. C.F. 220K OHM 1/6W +/-5% C 1 R251
08-29274T-MAN ASS'Y - MAIN BD 18-CB0271-JNX RES. C.F. 270 OHM 1/6W +/-5% C 1 R711
08-29274T-MAN ASS'Y - MAIN BD 18-CB0272-JNX RES. C.F. 2.7K OHM 1/6W +/-5% C 1 R227
08-29274T-MAN ASS'Y - MAIN BD 18-CB0331-JNX RES. C.F. 330 OHM 1/6W +/-5% C 4 R222, R223, R229, R259
08-29274T-MAN ASS'Y - MAIN BD 18-CB0333-JNX RES. C.F. 33K OHM 1/6W +/-5% C 5 R114, R208, R287, R289, R714
08-29274T-MAN ASS'Y - MAIN BD 18-CB0471-JNX RES. C.F. 470 OHM 1/6W +/-5% C 4 R125, R252, R931, R932
08-29274T-MAN ASS'Y - MAIN BD 18-CB0473-JNX RES. C.F. 47K OHM 1/6W +/-5% C 5 R052, R115, R262, R263, R284
08-29274T-MAN ASS'Y - MAIN BD 18-CB0560-JNX RES. C.F. 56 OHM 1/6W +/-5% C 1 R122
08-29274T-MAN ASS'Y - MAIN BD 18-CB0561-JNX RES. C.F. 560 OHM 1/6W +/-5% C 1 R228
08-29274T-MAN ASS'Y - MAIN BD 18-CB0750-JNX RES. C.F. 75 OHM 1/6W +/-5% C 1 R933
08-29274T-MAN ASS'Y - MAIN BD 18-CB0820-JNX RES. C.F. 82 OHM 1/6W +/-5% C 4 R913, R923, R971, R981
08-29274T-MAN ASS'Y - MAIN BD 18-CD0181-JNX RES. C.F. 180 OHM 1/4W +/-5% C 1 R226
08-29274T-MAN ASS'Y - MAIN BD 18-CD0222-JNX RES. C.F. 2.2K OHM 1/4W +/-5% C 1 R723
08-29274T-MAN ASS'Y - MAIN BD 18-CD0829-JNX RES. C.F. 8.2 OHM 1/4W +/-5% C 2 R607, R608
08-29274T-MAN ASS'Y - MAIN BD 18-CE0121-JNX RES. C.F. 120 OHM 1/2W +/-5% C 1 R731
08-29274T-MAN ASS'Y - MAIN BD 18-FF0103-JGX RES. M.O. 10K OHM 1W +/-5% C 1 R421
08-29274T-MAN ASS'Y - MAIN BD 18-FF0221-JGX RES. M.O. 220 OHM 1W +/-5% C 1 R307
08-29274T-MAN ASS'Y - MAIN BD 18-FF0242-JGX RES. M.O. 2.4K OHM 1W +/-5% C 1 R402
08-29274T-MAN ASS'Y - MAIN BD 18-FF0681-JGX RES. M.O. 680 OHM 1W +/-5% C 1 R411
08-29274T-MAN ASS'Y - MAIN BD 18-FG0399-JHX RES. M.O. 3.9 OHM 2W +/-5% C 1 R726
08-29274T-MAN ASS'Y - MAIN BD 18-GF0109-JGX RES WIRE ROUND 1 OHM 1W +/-5% C 1 R311
08-29274T-MAN ASS'Y - MAIN BD 18-GG0109-JHX RES WIRE ROUND 1 OHM 2W +/-5% C 1 R422
08-29274T-MAN ASS'Y - MAIN BD 26-AIC221-KBX CAP. CER 220 PF 500V +/-10% B C 2 C431, C441
08-29274T-MAN ASS'Y - MAIN BD 26-AIC332-KBX CAP. CER 3300 PF 500V +/-10% B C 1 C402
08-29274T-MAN ASS'Y - MAIN BD 26-AIC391-KBX CAP. CER 390 PF 500V +/-10% B C 1 C403
08-29274T-MAN ASS'Y - MAIN BD 34-A608K6-1BX COIL CHOKE 0.6 UH +/-10% C 1 L412
08-29274T-MAN ASS'Y - MAIN BD 34-R100J2-0EX COIL PL - 10 UH +/-5% C 1 L252
08-29274T-MAN ASS'Y - MAIN BD 34-R101J2-0EX COIL PL - 100 UH +/-5% C 3 L201, L211, L271
08-29274T-MAN ASS'Y - MAIN BD 34-R220J2-0EX COIL PL - 22 UH +/-5% C 3 L051, L081, L251
08-29274T-MAN ASS'Y - MAIN BD 34-R229J2-0EX COIL PL - 2.2 UH +/-5% C 1 L053
08-29274T-MAN ASS'Y - MAIN BD 41-WJ0080-B00 WIRE BARE JUMPER 8 MM C 4 J201, J425, J443, J453
08-29274T-MAN ASS'Y - MAIN BD 41-WJ0095-B00 WIRE BARE JUMPER 9.5MM C 4 J226, J343, J344, J713
08-29274T-MAN ASS'Y - MAIN BD 41-WJ0105-B00 WIRE BARE JUMPER 10.5MM C 3 J311, J442, J622
08-29274T-MAN ASS'Y - MAIN BD 41-WJ0115-B00 WIRE BARE JUMPER 11.5MM C 6 J052, J246, J342, J522, J627, J628
08-29274T-MAN ASS'Y - MAIN BD 41-WJ0140-B00 WIRE BARE JUMPER 14MM C 5 J321, J335, J336, J337, J742
08-29274T-MAN ASS'Y - MAIN BD 41-WJ0165-B00 WIRE BARE JUMPER 16.5MM C 3 J221, J234, J314
08-29274T-MAN ASS'Y - MAIN BD 41-WJ0180-B00 WIRE BARE JUMPER 18MM C 2 J214, J623
08-29274T-MAN ASS'Y - MAIN BD 41-WJ0195-B00 WIRE BARE JUMPER 19.5MM C 4 J323, J355, J641, J731
08-29274T-MAN ASS'Y - MAIN BD 54-128700-0X0 FIBRE WASHER 3.3 X 10 X 0.8 C 2 MTG M.BD & FBT
08-29274T-MAN ASS'Y - MAIN BD 62-10654X-00F UNI - TIE (2.5MMX95MM) C 12
08-29274T-MAN ASS'Y - MAIN BD 62-227680-0UA HOLDER CABLE FOR FBT (2) C 1
08-29274T-MAN ASS'Y - MAIN BD 67-H27292-1A0 HEAT SINK-REGULATOR & DPC A=60 C 1 FOR Q722
08-29274T-MAN ASS'Y - MAIN BD 18-CB0201-JNX RES. C.F. 200 OHM 1/6W +/-5% C 1 R993
08-29274T-MAN ASS'Y - MAIN BD 18-CD0100-JNX RES. C.F. 10 OHM 1/4W +/-5% C 1 R064
08-29274T-MAN ASS'Y - MAIN BD 18-CE0470-JNX RES. C.F. 47 OHM 1/2W +/-5% C 1 R103
08-29274T-MAN ASS'Y - MAIN BD 26-AIM103-KBX CAP. CER 0.01 UF 500V +/-10% B C 1 C401

R012, R203, R215, R216, R217, R255,
R261, R401

14

Sheet1

08-29274T-MAN ASS'Y - MAIN BD 18-FE0121-JNX RES. M.O. 120 OHM 1/2W +/-5% C 1 R306
08-29274T-MAN ASS'Y - MAIN BD 25-BCB220-M1X CAP. ELEC 22 UF 16V +/-20% C 1 C278
08-29274T-MAN ASS'Y - MAIN BD 25-BEA221-M1X CAP. ELEC 220 UF 35V +/-20% C 1 C306
08-29274T-MAN ASS'Y - MAIN BD 25-BEB101-M1X CAP. ELEC 100 UF 35V +/-20% C 1 C731
08-29274T-MAN ASS'Y - MAIN BD 25-BEG222-M1X CAP. ELEC 2200 UF 35V +/-20% C 2 C303, C309
08-29274T-MAN ASS'Y - MAIN BD 25-BFB100-M1X CAP. ELEC 10 UF 50V +/-20% C 2 C222, C311
08-29274T-MAN ASS'Y - MAIN BD 25-BFB108-M1X CAP. ELEC 0.1 UF 50V +/-20% C 1 C271
08-29274T-MAN ASS'Y - MAIN BD 25-BFB478-M1X CAP. ELEC 0.47 UF 50V +/-20% C 1 C208
08-29274T-MAN ASS'Y - MAIN BD 25-BFB479-M1X CAP. ELEC 4.7 UF 50V +/-20% C 2 C101, C124
08-29274T-MAN ASS'Y - MAIN BD 25-BKA100-M1X CAP. ELEC 10 UF 200V +/-20% C 1 C421
08-29274T-MAN ASS'Y - MAIN BD 25-BKG101-M1X CAP. ELEC 100 UF 200V +/-20% C 1 C422
08-29274T-MAN ASS'Y - MAIN BD 25-BLA100-M1X CAP. ELEC 10 UF 250V +/-20% C 1 C442
08-29274T-MAN ASS'Y - MAIN BD 38-236560-00X COIL I.F.T. 236560 FOR VCO C 1 T271
08-29274T-MAN ASS'Y - MAIN BD 41-WJ0190-B00 WIRE BARE JUMPER 19MM C 1 J823
08-29274T-MAN ASS'Y - MAIN BD 18-CB0752-JNX RES. C.F. 7.5K OHM 1/6W +/-5% C 2 R221, R288
08-29274T-MAN ASS'Y - MAIN BD 25-BFB101-M1X CAP. ELEC 100 UF 50V +/-20% C 1 C605
08-29274T-MAN ASS'Y - MAIN BD 18-CB0302-JNX RES. C.F. 3K OHM 1/6W +/-5% C 2 R601, R602
08-29274T-MAN ASS'Y - MAIN BD 25-GFB109-K1X CAP. ELEC 1UF 50V +/-10% C 1 C223
08-29274T-MAN ASS'Y - MAIN BD 18-EG0109-JHX RES. FUS. 1 OHM 2W +/-5% C 1 R431
08-29274T-MAN ASS'Y - MAIN BD 18-CB0470-JNX RES. C.F. 47 OHM 1/6W +/-5% C 5 R021, R077, R084, R085, R940

08-29274T-MAN ASS'Y - MAIN BD 41-WJ0175-B00 WIRE BARE JUMPER 17.5MM C 8
08-29274T-MAN ASS'Y - MAIN BD 18-CB0472-JNX RES. C.F. 4.7K OHM 1/6W +/-5% C 4 R066, R211, R965, R967

08-29274T-MAN ASS'Y - MAIN BD 18-CB0332-JNX RES. C.F. 3.3K OHM 1/6W +/-5% C 8
08-29274T-MAN ASS'Y - MAIN BD 67-H30147-1A0 HEAT SINK FOR HORIZ C 1 FOR Q412
08-29274T-MAN ASS'Y - MAIN BD 67-H30179-3A0 HEAT SINK C 1 FOR IC301
08-29274T-MAN ASS'Y - MAIN BD 41-WJ0090-B00 WIRE BARE JUMPER 9MM C 2 J031, J634
08-29274T-MAN ASS'Y - MAIN BD 41-WJ0170-B00 WIRE BARE JUMPER 17MM C 3 J231, J240, J835
08-29274T-MAN ASS'Y - MAIN BD 67-H30705-3A0 HEAT SINK C 1 FOR IC601

08-29274T-MAN ASS'Y - MAIN BD 18-CB0223-JNX RES. C.F. 22K OHM 1/6W +/-5% C 8
08-29274T-MAN ASS'Y - MAIN BD 71-270870-0A9 LABEL H 2
08-29274T-MAN ASS'Y - MAIN BD 27-PBC103-J0X CAP. P.E. 0.01UF 50V +/-5% C 1 C052
08-29274T-MAN ASS'Y - MAIN BD 25-BEA102-M1X CAP. ELEC 1000 UF 35V +/-20% C 2 C432, C610
08-29274T-MAN ASS'Y - MAIN BD 25-BEA471-M1X CAP. ELEC 470 UF 35V +/-20% C 2 C607, C608
08-29274T-MAN ASS'Y - MAIN BD 18-FE0472-JNX RES. M.O. 4.7K OHM 1/2W +/-5% C 1 R471
08-29274T-MAN ASS'Y - MAIN BD 18-GM0302-KTX RES. CEMENT 3K OHM 7W +/-10% C 1 R404

08-29274T-MAN ASS'Y - MAIN BD 41-WJ0065-B00 WIRE BARE JUMPER 6.5MM C 8
08-29274T-MAN ASS'Y - MAIN BD 41-WJ0110-B00 WIRE BARE JUMPER 11MM C 11
08-29274T-MAN ASS'Y - MAIN BD 41-WJ0200-B00 WIRE BARE JUMPER 20MM C 7
08-29274T-MAN ASS'Y - MAIN BD 41-WJ0125-B00 WIRE BARE JUMPER 12.5MM C 12

08-29274T-MAN ASS'Y - MAIN BD 10-0BY228-F0X DIODE BY228 (FAST RECTIFIER) C 1 D411
08-29274T-MAN ASS'Y - MAIN BD 10-1N4001-EBX DIODE 1N4001 (RECTIFIER) C 1 D301
08-29274T-MAN ASS'Y - MAIN BD 10-55C12V-DBX DIODE ZENER 12V 1/2W +/-5% C 2 D731, D732
08-29274T-MAN ASS'Y - MAIN BD 10-55C4V7-DBX DIODE ZENER 4.7V 1/2W +/-5% C 1 D222
08-29274T-MAN ASS'Y - MAIN BD 10-55C5V1-DBX DIODE ZENER 5V1 1/2W +/-5% C 2 D061, D101

J223, J249A, J251, J661, J771, J811,
J912, J913

R013, R014, R074, R076, R111, R254,
R302, R472

R092, R631, R722, R915, R916, R920,
R925, R952

J410, J511, J514, J615, J632, J725,
J729, R238

J227, J228, J244, J302, J313, J322,
J324, J612, J614, J625, JP213

J312, J427, J624, J626, J727, J824,
J831

J131, J206, J218, J222, J225, J263,
J352, J643, J772, J813, J951, J981

15

Sheet1

Q931, Q932

C001, C002, C013, C061, C062, C127

X

C202, C274, C911, C912, C913, C921

08-29274T-MAN ASS'Y - MAIN BD 10-55C8V2-DBX DIODE ZENER 8V2 1/2W +/-5% C 2 D240, D471
08-29274T-MAN ASS'Y - MAIN BD 10-CW574C-DJX DIODE CW574CS C 1 D111
08-29274T-MAN ASS'Y - MAIN BD 10-TFR104-FBX DIODE TFR104 (FAST RECOVERY) C 4 D412, D421, D431, D441

08-29274T-MAN ASS'Y - MAIN BD 11-SA1015-YBX TRANSISTOR 2SA1015Y C 7
08-29274T-MAN ASS'Y - MAIN BD 27-MBC224-J0X CAP. M.P.E. 0.22 UF 50V +/-5% C 1 C113
08-29274T-MAN ASS'Y - MAIN BD 11-0BC337-0BX TRANSISTOR BC337-40 (NPN) C 1 Q062
08-29274T-MAN ASS'Y - MAIN BD 11-2N3904-0BX TRANSISTOR 2N3904 (NPN) C 1 Q091

08-29274T-MAN ASS'Y - MAIN BD 11-SC1815-YBX TRANSISTOR 2SC1815Y C 24
08-29274T-MAN ASS'Y - MAIN BD 11-SC3779-DBX TRANSISTOR 2SC3779D (RF AMPL) H 1 Q121
08-29274T-MAN ASS'Y - MAIN BD 11-SC4544-0AX TRANSISTOR 2SC4544 (NPN) C 1 Q401
08-29274T-MAN ASS'Y - MAIN BD 11-DD1556-0AX TRANSISTOR 3DD1556 (HORIZ) C 1 Q412
08-29274T-MAN ASS'Y - MAIN BD 11-SD1499-QAX TRANSISTOR 2SD1499Q (POWER) H 1 Q722
08-29274T-MAN ASS'Y - MAIN BD 11-SK2541-0BX TRANSISTOR 2SK2541 (N-CHANNEL) H 2 Q052, Q212
08-29274T-MAN ASS'Y - MAIN BD 25-264610-M1X CAP. ELEC 4.7UF 50V +/-20% NP C 1 C417
08-29274T-MAN ASS'Y - MAIN BD 26-EBP101-JCX CAP. CER 100 PF 50V +/-5% CH H 5 C032, C071, C254, C255, C272

08-29274T-MAN ASS'Y - MAIN BD 26-EBP102-KBX CAP. CER 1000 PF 50V +/-10% B H 16
08-29274T-MAN ASS'Y - MAIN BD 26-EBP120-JCX CAP. CER 12 PF 50V +/-5% CH H 1 C209
08-29274T-MAN ASS'Y - MAIN BD 26-EBP150-JCX CAP. CER 15 PF 50V +/-5% CH H 4 C041, C042, C043, C044
08-29274T-MAN ASS'Y - MAIN BD 26-EBP222-KB
08-29274T-MAN ASS'Y - MAIN BD 26-EBP300-JZX CAP. CER 30 PF 50V +/-5% SL H 2 C055, C056
08-29274T-MAN ASS'Y - MAIN BD 26-EBP330-JZX CAP. CER 33 PF 50V 5% SL TUBU H 2 C128, C953
08-29274T-MAN ASS'Y - MAIN BD 26-EBP331-JCX CAP. CER 330 PF 50V +/-5% CH H 6 C004, C063, C084, C085, C091, C301
08-29274T-MAN ASS'Y - MAIN BD 26-EBP390-JCX CAP. CER 39 PF 50V +/-5% CH H 1 C051
08-29274T-MAN ASS'Y - MAIN BD 26-EBP470-JZX CAP. CER 47 PF 50V +/-5% SL H 4 C072, C073, C261, T141
08-29274T-MAN ASS'Y - MAIN BD 27-MCC272-J0X CAP. P.E. 2700 PF 100V +/-5% C 1 C471
08-29274T-MAN ASS'Y - MAIN BD 45-OSC4M4-3Y0 CRYSTAL 4.43 MHZ C 1 X201
08-29274T-MAN ASS'Y - MAIN BD 45-TRA5M5-0Y0 CER. TRAP 5.5 MHZ C 1 Z254
08-29274T-MAN ASS'Y - MAIN BD 45-OSC8M0-0Y0 CRYSTAL 8.0MHZ C 1 X051

08-29274T-MAN ASS'Y - MAIN BD 46-20598W-04X PIN BASE *4 TJC1-4A C 1 P411
08-29274T-MAN ASS'Y - MAIN BD 47-SVI002-XX0 SOCKET S-W16-J C 1 P981
08-29274T-MAN ASS'Y - MAIN BD 63-B30100-BT4 S/T SCREW B 3 X 10 BT C 2 MTG M.BD & FBT
08-29274T-MAN ASS'Y - MAIN BD 63-W30100-AB4 S/T SCREW W 3 X 10 AB C 7 MTG M.BD & BKT
08-29274T-MAN ASS'Y - MAIN BD 64-P30080-104 M/C SCREW P 3 X 8 C 1 FOR Q722
08-29274T-MAN ASS'Y - MAIN BD 64-P30080-104 M/C SCREW P 3 X 8 C 1 FOR IC301
08-29274T-MAN ASS'Y - MAIN BD 64-P30080-104 M/C SCREW P 3 X 8 C 1 FOR Q412
08-29274T-MAN ASS'Y - MAIN BD 64-P30100-104 M/C SCREW P 3 X 10 C 2 FOR IC601
08-29274T-MAN ASS'Y - MAIN BD 65-Z30050-23M NUT M 3 C 2 FOR IC301 & Q412
08-29274T-MAN ASS'Y - MAIN BD 65-Z30050-23M NUT M 3 C 2 FOR IC601
08-29274T-MAN ASS'Y - MAIN BD 37-BSC290-1650X FLYBACK BSC29-0165 C 1 T461

08-29274T-MAN ASS'Y - MAIN BD 25-BCB470-M1X CAP. ELEC 47 UF 16V +/-20% C 13

CAP. CER 2200PF 50V +/-10% B H 1 C452

Q061, Q211, Q241, Q242, Q633,
Q721, Q934

Q001, Q002, Q031, Q051, Q251,
Q252, Q261, Q451, Q631, Q711,
Q911, Q912, Q913, Q921, Q922, Q923

C224, C305, C312, C411, C602, C606,
C936, C937, C942, C971

C922, C923, C931, C932, C943, C981,
C991

,
Q933, Q963,
Q964, Q971,
Q981, Q991

,

FOR DY
CONNECT.

,

16

Sheet1

R005, R012A, R017, R029, R031

D041, D042, D043, D044, D211, D212

J122, J204, J205, J348, J409, J424

J512, J523, J543

J408, J412, J541

,

R051, R054, R055, R061, R101, R102,
08-29274T-MAN ASS'Y - MAIN BD 18-CB0103-JNX RES. C.F. 10K OHM 1/6W +/-5% C 20
08-29274T-MAN ASS'Y - MAIN BD 25-BCB221-M1X CAP. ELEC 220 UF 16V +/-20% C 2 C634, C933

08-29274T-MAN ASS'Y - MAIN BD 10-1N4148-ABX DIODE 1N4148 (SWITCHING) C 13

08-29274T-MAN ASS'Y - MAIN BD 41-WJ0085-B00 WIRE BARE JUMPER 8.5MM C 14
08-29274T-MAN ASS'Y - MAIN BD 41-WJ0135-B00 WIRE BARE JUMPER 13.5MM C 7

08-29274T-MAN ASS'Y - MAIN BD 41-WJ0130-B00 WIRE BARE JUMPER 13MM C 3 J239, J346, J413
08-29274T-MAN ASS'Y - MAIN BD 26-EBP221-JCX CAP. CER 220 PF 50V +/-5% CH H 4 C021, C092, C112, C228A

08-29274T-MAN ASS'Y - MAIN BD 18-CB0153-JNX RES. C.F. 15K OHM 1/6W +/-5% C 7
08-29274T-MAN ASS'Y - MAIN BD 46-33079W-04X PIN BASE *4 TJC3-4A C 1 P421
08-29274T-MAN ASS'Y - MAIN BD 46-33079W-06X PIN BASE *6 TJC3-6A C 1 P002

08-29274T-MAN ASS'Y - MAIN BD 46-33079W-06X PIN BASE *6 TJC3-6A C 1 P003 FOR SIDE AV BD
08-29274T-MAN ASS'Y - MAIN BD 46-33079W-02X PIN BASE *2 TJC3-2A C 1 P602
08-29274T-MAN ASS'Y - MAIN BD 46-33079W-05X PIN BASE *5 TJC3-5A C 1 P001
08-29274T-MAN ASS'Y - MAIN BD 46-33079W-05X PIN BASE *5 TJC3-5A C 1 P201

08-29274T-MAN ASS'Y - MAIN BD 26-EBP220-JCX CAP. CER 22 PF 50V +/-5% CH H 2 C053, C054
08-29274T-MAN ASS'Y - MAIN BD 47-RCA023-XX1 RCA JACK 3PV YEL WHI RED/SW H 2 P911, P931

08-29274T-MAN ASS'Y - MAIN BD 41-WJ0060-B00 WIRE BARE JUMPER 6MM C 42

08-29274T-MAN ASS'Y - MAIN BD 41-WJ0075-B00 WIRE BARE JUMPER 7.5MM C 33
08-29274T-MAN ASS'Y - MAIN BD 07-389VI5-NX4 TUNER UV1355-BK2(BG/HB/IEC/5V) H 1 TU101
08-29274T-MAN ASS'Y - MAIN BD 36-HDR001-XX1 TRANSFORMER HORIZ DRIVE C 1 T401
08-29274T-MAN ASS'Y - MAIN BD 90-209770-SR1 SILICONE GREASE G-746 (1KG/CAN H 0.0009 FOR IC601 & Q412 & Q722
08-29274T-MAN ASS'Y - MAIN BD 90-269080-ZU0 CLEAN COATING TC-131L 14KG/BAR H 0.0001
08-29274T-MAN ASS'Y - MAIN BD 13-00M24C-08P IC M24C08 EEPROM 8K 1 IC002
08-29274T-MAN ASS'Y - MAIN BD 13-0TA842-7KS IC TA8427K 1 IC301
08-29274T-MAN ASS'Y - MAIN BD 34-A109K2-1IX COIL CHOKE 1 UH +/-10% (5MM) C 2 L121, L141
08-29274T-MAN ASS'Y - MAIN BD 25-BCA471-M1X CAP. ELEC 470 UF 16V +/-20% C 1 C082
08-29274T-MAN ASS'Y - MAIN BD 45-SAWK33-50K SAW FILTER K3350K (38.9MHZ) H 1 Z141
08-29274T-MAN ASS'Y - MAIN BD 27-MBC474-J0X CAP. M.P.E. 0.47 UF 50V +/-5% C 4 C225, C243, C603, C604

R225, R237, R633, R716, R757

D213, D221, D223, D280, D632, D711,

D721

J441, J502, J503, J553, J554, J621,

J723, J822

J224, J236, J247, J248A, J345, J411,

R228A

R057, R072, R112, R113, R452,

R632A, R987

J022A, J044, J123, J132, J141, J229,

J230, J232, J242, J261, J301, J327,

J328, J338, J401, J421

D141, J041, J043, J124, J151, J152,

J154, J207, J208, J217, J241, J331,

J351, J405, J406, J407

R960, R961,
R962, R989

,

,

FOR CRT BD
P502

FOR W.BAL.
ADJUST

FOR FRONT
CAB.(SPK)

FOR F CTL BD
P001B

FOR CRT BD
P503

J601, J633, J732,
J733, J825, J826,
J832, J834, J836,
J837, J838, J911,
J921

J544, J551, J642,
J651, J656, J693,
J712, J734, J812,
J821, J833, J851,
J915, J941

,

R023, R024, R025, R026,
R027, R028A, R028B,
R028C, R126, R224

,

17

Sheet1

C075, C083, C111, C121, C125, C126

C262, C661, C662, C946, J410A, J415

J001, J002, J061, J134, J135, J203

J032, J133, J153, J235, J237, J243

D215, D631, R041, R042, R043, R044

08-29274T-MAN ASS'Y - MAIN BD 13-274020-00P IC TMP87PS38N M3 TSB CPU (OTP) H 1 IC001
08-29274T-MAN ASS'Y - MAIN BD 18-CB0101-JNX RES. C.F. 100 OHM 1/6W +/-5% C 11
08-29274T-MAN ASS'Y - MAIN BD 25-BCB100-M1X CAP. ELEC 10 UF 16V +/-20% C 8
08-29274T-MAN ASS'Y - MAIN BD 25-BCB101-M1X CAP. ELEC 100 UF 16V +/-20% C 7

08-29274T-MAN ASS'Y - MAIN BD 25-BFB109-M1X CAP. ELEC 1 UF 50V +/-20% C 3 C206, C253, C631

08-29274T-MAN ASS'Y - MAIN BD 26-EBP103-ZFX CAP. CER 0.01UF 50V +80-20% F H 18
08-29274T-MAN ASS'Y - MAIN BD 26-EBP104-ZFX CAP. CER 0.1UF 50V +80-20% F H 7

08-29274T-MAN ASS'Y - MAIN BD 41-WJ0050-B00 WIRE BARE JUMPER 5MM C 20
08-29274T-MAN ASS'Y - MAIN BD 41-WJ0070-B00 WIRE BARE JUMPER 7MM C 8

08-29274T-MAN ASS'Y - MAIN BD 41-WJ0100-B00 WIRE BARE JUMPER 10MM C 18
08-29274T-MAN ASS'Y - MAIN BD 41-WJ0120-B00 WIRE BARE JUMPER 12MM C 7

08-29274T-MAN ASS'Y - MAIN BD 41-WJ0150-B00 WIRE BARE JUMPER 15MM C 15
08-29274T-MAN ASS'Y - MAIN BD 41-WJ0160-B00 WIRE BARE JUMPER 16MM C 5 J238, J325, J334, J431, J645

08-29274T-MAN ASS'Y - MAIN BD 46-27306H-02X HS 2P24 150/5 F/W S11-02H C 1

08-29274T-MAN ASS'Y - MAIN BD 18-CB0222-JNX RES. C.F. 2.2K OHM 1/6W +/-5% C 15
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 67-H29550-8A0 HEAT SINK C 1 FOR IC801
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 67-H34692-0A0 HEAT SINK C 1 FOR IC801
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 26-AKK222-KRX CAP. CER 2200 PF 1KV +/-10% R C 1 C814
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 13-00SE12-5NS IC SE125N-LF12 ERROR H 1 IC831
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 18-CD0472-JNX RES. C.F. 4.7K OHM 1/4W +/-5% C 1 R831
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 66-343730-0B0 HOLLOW RIVET 1.6X3.0XL3.2 C 4 FOR T802
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 13-STRF66-56P IC STR-F6656 H 1 IC801
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 18-CB0152-JNX RES. C.F. 1.5K OHM 1/6W +/-5% C 1 R833
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 18-CB0223-JNX RES. C.F. 22K OHM 1/6W +/-5% C 1 R840
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 18-CB0332-JNX RES. C.F. 3.3K OHM 1/6W +/-5% C 1 R838
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 18-CB0392-JNX RES. C.F. 3.9K OHM 1/6W +/-5% C 1 R841
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 18-CD0102-JNX RES. C.F. 1K OHM 1/4W +/-5% C 2 R805, R808
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 18-CD0272-JNX RES. C.F. 2.7K OHM 1/4W +/-5% C 1 R813
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 18-CD0470-JNX RES. C.F. 47 OHM 1/4W +/-5% C 1 R809
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 18-CD0479-JNX RES. C.F. 4.7 OHM 1/4W +/-5% C 1 R811
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 18-CD0829-JNX RES. C.F. 8.2 OHM 1/4W +/-5% C 1 R842
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 18-CE0105-JNX RES. C.F. 1M OHM 1/2W +/-5% C 2 R806, R806A
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 18-CE0563-JNX RES. C.F. 56K OHM 1/2W +/-5% C 2 R803, R804
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 18-FG0223-JHX RES. M.O. 22K OHM 2W +/-5% C 1 R836

R003, R006, R007, R009, R015, R016,

R065, R073, R075, R241, R253

C074, C106, C214, C227, C276, C651,

C655, C952

C064, C217, C228, C257, C934, C944,

C969

C203, C205, C215, C226, C229, C256,

C273, C275, C732, C935 C961, C962

C107, C114, C204, C609, C635, C745,

C945

J416, J417, J418, J419, J420, J435,

J436, J437, J636, J637

J023, J233A, J426, J513, J671, J672,

J726, J741

J402, J423, J432, J501, J611, J631,

J652, J653, J692, J728 J735, J916

J051, J250, J253, J254, J434, J644,

J711

J245, J255, J262, J347, J461, J542,

J714, J761, J931

FOR Q931(B)&Q932(B) TO NICAM BD

P1003

R218, R242, R713, R914, R924, R972,

R982, R988, R991

,

,

J773, J871, J954,
J955

,

,

,

18

Sheet1

08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 18-FG0333-JHX RES. M.O. 33K OHM 2W +/-5% C 2 R810, R839
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 18-GG0228-JHX RES WIRE ROUND 0.22 OHM 2W 5% C 1 R830
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 26-AIC221-KBX CAP. CER 220 PF 500V +/-10% B C 5 C830, C833, C836, C841, C844
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 26-AIM103-KBX CAP. CER 0.01 UF 500V +/-10% B C 3 C805, C834, C837
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 26-AQK472-ZFX CAP. CER 4700PF 250VAC+80-20%F C 2 C803, C804
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 27-AQT224-MVF CAP. M.PP 0.22UF 250VAC 20% CB H 2 C801, C802
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 35-237250-00X FERR. BEAD HF70 C 2 FOR D804
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 41-WJ0175-B00 WIRE BARE JUMPER 17.5MM C 2 J271, J281
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 41-WJ0190-B00 WIRE BARE JUMPER 19MM C 1 J354
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 41-WJ0200-B00 WIRE BARE JUMPER 20MM C 1 J381
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 66-20516X-0B0 FUSE HOLDER C 2 FOR F801
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 67-H10918-4M2 HEAT SINK C 2 FOR IC841 & IC851
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 13-00MC78-09S IC MC7809C LINEAR +9V 1A H 1 IC851
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 27-MHM104-K0X CAP. METAL P.E. 0.1UF 400V 10% C 1 C802A
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 35-237250-00X FERR. BEAD HF70 C 2 FOR D831
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 35-237250-00X FERR. BEAD HF70 C 2 FOR D832
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 35-237250-00X FERR. BEAD HF70 C 2 FOR D833
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 35-237250-00X FERR. BEAD HF70 C 2 FOR D834
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 50-26931D-1VS FUSE 3.15AT 250VAC 5X20MM BELL H 1 F801
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 18-CD0560-JNX RES. C.F. 56 OHM 1/4W +/-5% C 1 R837
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 25-BCB470-M1X CAP. ELEC 47 UF 16V +/-20% C 2 C849, C855
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 25-BDB470-M1X CAP. ELEC 47 UF 25V +/-20% C 1 C809
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 25-BEA102-M1X CAP. ELEC 1000 UF 35V +/-20% C 1 C832
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 25-BKA100-M1X CAP. ELEC 10 UF 200V +/-20% C 2 C808, C838
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 25-BKJ221-M1X CAP. ELEC 220 UF 200V +/-20% C 1 C835
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 41-WJ0065-B00 WIRE BARE JUMPER 6.5MM C 1 J451
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 41-WJ0100-B00 WIRE BARE JUMPER 10MM C 3 J371, J654, J655
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 41-WJ0145-B00 WIRE BARE JUMPER 14.5MM C 1 J491
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 41-WJ0180-B00 WIRE BARE JUMPER 18MM C 1 J353
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 41-WJ0075-B00 WIRE BARE JUMPER 7.5MM C 1 J471
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 41-WJ0155-B00 WIRE BARE JUMPER 15.5MM C 2 J561, J562
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 18-KE0105-JNX RES. H. VOLT. CC 1M OHM 1/2W C 1 R801
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 35-237250-00X FERR. BEAD HF70 C 2 FOR D830
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 36-TRF001-XX2 TRANSFORMER CONV. KB49C1640 C 1 T802
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 25-BCB331-M1X CAP. ELEC 330 UF 16V +/-20% C 1 C843
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 18-GG0158-JHX RES WIRE ROUND 0.15 OHM 2W 5% C 1 R807
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 10-0TEU1Z-FBX DIODE EU1Z (FAST RECOVERY) C 3 D804, D805, D806
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 10-0EG01C-FBX DIODE EG01C (FAST RECTIFIER) C 1 D803
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 10-1N4004-EBX DIODE IN4004 (RECTIFIER) C 1 D843
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 10-1N4148-ABX DIODE 1N4148 (SWITCHING) C 1 D842
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 10-55C10V-DBX DIODE ZENER 10V 1/2W +/-5% C 1 D840
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 10-55C16V-DBX DIODE ZENER 16V 1/2W +/-5% C 1 D807
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 10-55C2V4-DBX DIODE ZENER 2V4 1/2W 5% C 1 D841
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 10-55C3V9-DBX DIODE ZENER 3.9V 1/2W +/-5% C 1 D839
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 10-T3SB60-H7X DIODE T3SB60 (BRIDGE RECT.) C 1 DB801
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 10-TFR104-FBX DIODE TFR104 (FAST RECOVERY) C 1 D832
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 11-0BF422-0BX TRANSISTOR BF422 H 1 Q831
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 11-SB649A-0AX TRANSISTOR 2SB649A H 1 Q830
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 11-SC4793-0AX TRANSISTOR 2SC4793 (VM) H 1 Q801
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 13-000L78-05S IC L7805 CV 5V 1A (REGUALTOR) H 1 IC841
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 13-SFH615-A3P PHOTO COUPLER SFH615A3C H 1 IC802

19

Sheet1

X

FOR

08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 22-NTC479-XX0 NTC 4.7 OHM +/-18% NTC4.7D2-14 C 1 R802
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 26-EBP104-ZFX CAP. CER 0.1UF 50V +80-20% F H 7

08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 26-AMK221-JZX CAP. CER 220 PF 2KV +/-5% SL C 1 FOR P2 - P3 OF IC801
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 26-AMK221-JZX CAP. CER 220 PF 2KV +/-5% SL C 1 C807
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 26-EBP102-KB
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 26-EBP103-ZFX CAP. CER 0.01UF 50V +80-20% F H 1 C815
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 26-EBP221-JCX CAP. CER 220 PF 50V +/-5% CH H 1 C810

08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 46-10962W-02X PIN BASE *2 TJC2-2A C 1 P801
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 46-28559W-02X PIN BASE *2 TJC1-2A C 1 P802A
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 65-Z30050-23M NUT M 3 C 1 FOR IC801
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 41-WJ0050-B00 WIRE BARE JUMPER 5MM C 6 J802, J804, J805, J806, J807, J808
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 41-WJ0150-B00 WIRE BARE JUMPER 15MM C 1 R812
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 41-WJ0125-B00 WIRE BARE JUMPER 12.5MM C 2 J361, J492
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 22-PTC140-XX0 PTC 14 OHM C 1 RT801
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 18-KF0825-JHX VOLTAGE RES. 8.2M OHM 1W +/-5% C 1 R835
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 36-LIF002-XX0 LINE FILTER 20 MH C 1 T803
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 36-LIF005-XX0 LINE FILTER C 1 T801

08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 64-P30080-104 M/C SCREW P 3 X 8 C 2
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 64-P30080-104 M/C SCREW P 3 X 8 C 2 FOR IC841 & IC851
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 64-B30120-104 M/C SCREW B 3 X 12 C 1 FOR IC801
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 10-0EU2YX-F0X DIODE EU2YX (FAST RECOVERY) C 2 D833, D834
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 10-0RU3AM-F01 DIODE RU3AM (FAST RECOVERY) 1 D831
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 10-0RU4YX-F0X DIODE RU4YX (FAST RECOVERY) C 1 D830
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 34-R220K2-1BX COIL CHOKE 22 UH +/-10% C 1 L838
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 25-BMJ221-M1X CAP. ELEC 220 UF 400V +/-20% C 1 C806
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 34-A608K6-1BX COIL CHOKE 0.6 UH +/-10% C 1 L801
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 66-343730-0B0 HOLLOW RIVET 1.6X3.0XL3.2 C 2 FOR DB801
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 26-APK222-ME4 CAP. CER 2200PF 400VAC+/-20% E C 1 C839
08-02927T-PW1 ASS'Y - POWER PARTS "AUST" 26-APK471-KB4 CAP. CER 470PF 400VAC +/-10% B H 2 C812, C813
08-02927T-FB1 ASS'Y - F.CTL & SW.BD "AUST" 40-2927UA-FBA P.C.B. FRONT CTL & SW BD C 1
08-02927T-FB1 ASS'Y - F.CTL & SW.BD "AUST" 41-WJ0075-B00 WIRE BARE JUMPER 7.5MM C 1 J075
08-02927T-FB1 ASS'Y - F.CTL & SW.BD "AUST" 48-325390-002 SWITCH POWER PS5E-B C 1 S801B
08-02927T-FB1 ASS'Y - F.CTL & SW.BD "AUST" 62-269940-0HA POWER SW. ADAPTER C 1
08-02927T-FB1 ASS'Y - F.CTL & SW.BD "AUST" 18-CB0332-JNX RES. C.F. 3.3K OHM 1/6W +/-5% C 1 R025A
08-02927T-FB1 ASS'Y - F.CTL & SW.BD "AUST" 18-CB0470-JNX RES. C.F. 47 OHM 1/6W +/-5% C 1 R070A
08-02927T-FB1 ASS'Y - F.CTL & SW.BD "AUST" 18-CB0471-JNX RES. C.F. 470 OHM 1/6W +/-5% C 1 R033B
08-02927T-FB1 ASS'Y - F.CTL & SW.BD "AUST" 18-CB0102-JNX RES. C.F. 1K OHM 1/6W +/-5% C 1 R033A
08-02927T-FB1 ASS'Y - F.CTL & SW.BD "AUST" 18-CB0822-JNX RES. C.F. 8.2K OHM 1/6W +/-5% C 2 R022A, R026A
08-02927T-FB1 ASS'Y - F.CTL & SW.BD "AUST" 18-CB0153-JNX RES. C.F. 15K OHM 1/6W +/-5% C 1 R027A
08-02927T-FB1 ASS'Y - F.CTL & SW.BD "AUST" 51-JC0243-0CH POWER CORD SAA PLUG W/HOUSING H 1
08-02927T-FB1 ASS'Y - F.CTL & SW.BD "AUST" 62-310430-0HA LED HOLDER (COMMON) (8MM) C 1
08-02927T-FB1 ASS'Y - F.CTL & SW.BD "AUST" 18-CB0152-JNX RES. C.F. 1.5K OHM 1/6W +/-5% C 1 R023A
08-02927T-FB1 ASS'Y - F.CTL & SW.BD "AUST" 18-CB0182-JNX RES. C.F. 1.8K OHM 1/6W +/-5% C 1 R024A
08-02927T-FB1 ASS'Y - F.CTL & SW.BD "AUST" 18-CB0473-JNX RES. C.F. 47K OHM 1/6W +/-5% C 1 R027B
08-02927T-FB1 ASS'Y - F.CTL & SW.BD "AUST" 25-BCB470-M1X CAP. ELEC 47 UF 16V +/-20% C 1 C070A
08-02927T-FB1 ASS'Y - F.CTL & SW.BD "AUST" 41-WJ0060-B00 WIRE BARE JUMPER 6MM C 3 J070, J071, J074
08-02927T-FB1 ASS'Y - F.CTL & SW.BD "AUST" 14-LED05R-XX0 LED HFR105 (5MM) C 1 D1001

CAP. CER 1000 PF 50V +/-10% B H 1 C811

C831, C842, C845, C847, C848, C854,

C856

MTG H.SINK(67-H29550-8A0&67-

H34692-0A0)

DEGAUSSING
COIL

20

Sheet1

FOR CRT

FOR POWER
08-02927T-FB1 ASS'Y - F.CTL & SW.BD "AUST" 46-28559W-02X PIN BASE *2 TJC1-2A C 1 P801B
08-02927T-FB1 ASS'Y - F.CTL & SW.BD "AUST" 46-28559W-02X PIN BASE *2 TJC1-2A C 1 P801A
08-02927T-FB1 ASS'Y - F.CTL & SW.BD "AUST" 63-P30060-0B3 S/T SCREW P 3 X 6 B (BLACK) C 5 MTG F.CTL BD & M.BD BKT
08-02927T-FB1 ASS'Y - F.CTL & SW.BD "AUST" 46-30407H-05X HS UL2468#24 5C/TS 180 TJC3-5Y C 1 P001B FOR M. BD P001

08-02927T-FB1 ASS'Y - F.CTL & SW.BD "AUST" 46-32269H-02X HS 2P22 200 TJC1-2Y/TJC1-2Y C 1
08-02927T-FB1 ASS'Y - F.CTL & SW.BD "AUST" 11-IRR001-1X0 IR RECEIVER HS0038A2 C 1 IR001

08-02927T-FB1 ASS'Y - F.CTL & SW.BD "AUST" 48-TAC002-XX0 SW. TACT VERT (H=4MM L=6.4MM) C 7
08-02916T-CR3 ASS'Y - CRT BD (NOVEL) 18-FG0183-JHX RES. M.O. 18K OHM 2W +/-5% C 3 R516, R517, R518
08-02916T-CR3 ASS'Y - CRT BD (NOVEL) 18-CB0102-JNX RES. C.F. 1K OHM 1/6W +/-5% C 1 R515
08-02916T-CR3 ASS'Y - CRT BD (NOVEL) 18-CB0561-JNX RES. C.F. 560 OHM 1/6W +/-5% C 3 R501, R505, R510

08-02916T-CR3 ASS'Y - CRT BD (NOVEL) 18-CB0681-JNX RES. C.F. 680 OHM 1/6W +/-5% C 8
08-02916T-CR3 ASS'Y - CRT BD (NOVEL) 35-237250-00X FERR. BEAD HF70 C 2 FOR C508 (L505 & L506)
08-02916T-CR3 ASS'Y - CRT BD (NOVEL) 41-WJ0050-B00 WIRE BARE JUMPER 5MM C 1 L504
08-02916T-CR3 ASS'Y - CRT BD (NOVEL) 41-WJ0075-B00 WIRE BARE JUMPER 7.5MM C 1 J503
08-02916T-CR3 ASS'Y - CRT BD (NOVEL) 18-CB0272-JNX RES. C.F. 2.7K OHM 1/6W +/-5% C 1 R514
08-02916T-CR3 ASS'Y - CRT BD (NOVEL) 47-265540-1U5 SOCKET CRT GZS10-2-108D C 1 S501
08-02916T-CR3 ASS'Y - CRT BD (NOVEL) 25-BLA100-M1X CAP. ELEC 10 UF 250V +/-20% C 1 C504
08-02916T-CR3 ASS'Y - CRT BD (NOVEL) 18-FE0272-JNX RES. M.O. 2.7K OHM 1/2W +/-5% C 3 R519, R520, R521
08-02916T-CR3 ASS'Y - CRT BD (NOVEL) 10-1N4148-ABX DIODE 1N4148 (SWITCHING) C 3 D501, D502, L501
08-02916T-CR3 ASS'Y - CRT BD (NOVEL) 40-02501C-CRG P.C.B. CRT BD C 1
08-02916T-CR3 ASS'Y - CRT BD (NOVEL) 11-A562TM-0BX TRANSISTOR 2SA562TM-0 C 1 Q507
08-02916T-CR3 ASS'Y - CRT BD (NOVEL) 11-SC1815-YBX TRANSISTOR 2SC1815Y C 3 Q502, Q504, Q506
08-02916T-CR3 ASS'Y - CRT BD (NOVEL) 11-SC4544-0AX TRANSISTOR 2SC4544 (NPN) C 3 Q501, Q503, Q505
08-02916T-CR3 ASS'Y - CRT BD (NOVEL) 26-EBP471-JCX CAP. CER 470 PF 50V +/-5% CH H 1 C503
08-02916T-CR3 ASS'Y - CRT BD (NOVEL) 26-EBP391-JCX CAP. CER. 390PF 50V +/-5% CH H 2 C501, C502
08-02916T-CR3 ASS'Y - CRT BD (NOVEL) 26-EBP103-ZFX CAP. CER 0.01UF 50V +80-20% F H 2 C508, C509

FOR F. CTL BD(P801A) &
M.BD(P802A)

S001A, S002A, S003A, S004A, S005A,
S006A, S007A

R502, R503, R506, R508, R509, R511,
R513, R522

CORD

GROUNDING
08-02916T-CR3 ASS'Y - CRT BD (NOVEL) 46-10967W-01X PIN BASE *1 TJC1-1A C 1 P501
08-02916T-CR3 ASS'Y - CRT BD (NOVEL) 46-30615H-04X HS 4P24 460 F/W TJC3-4Y/SCN-4 C 1 P502 FOR M. BD P421
08-02916T-CR3 ASS'Y - CRT BD (NOVEL) 41-WJ0060-B00 WIRE BARE JUMPER 6MM C 4 J510, R504, R507, R512
08-02916T-CR3 ASS'Y - CRT BD (NOVEL) 34-R220K2-1BX COIL CHOKE 22 UH +/-10% C 2 L502, L503
08-02916T-CR3 ASS'Y - CRT BD (NOVEL) 25-BCA471-M1X CAP. ELEC 470 UF 16V +/-20% C 1 C506
08-02916T-CR3 ASS'Y - CRT BD (NOVEL) 26-AMK182-KRX CAP. CER 1800PF 2KV +/-10% R C 1 C505
08-02916T-CR3 ASS'Y - CRT BD (NOVEL) 46-37030H-05X HS 5P 2468#24 450 TJC3-5Y/SCN C 1 P503 FOR M. BD P201

08-02927T-AVY ASS'Y - SIDE AV BD 46-29272H-06X HS 6P24 275 F/W TJC3-6Y/SCN-6Y C 1 P902
08-02927T-AVY ASS'Y - SIDE AV BD 40-2927MT-SIB P.C.B. SIDE AV BD C 1
08-02927T-AVY ASS'Y - SIDE AV BD 41-WJ0060-B00 WIRE BARE JUMPER 6MM C 4 C954, C955, J955, R953
08-02927T-AVY ASS'Y - SIDE AV BD 41-WJ0065-B00 WIRE BARE JUMPER 6.5MM C 2 R952, R967
08-02927T-AVY ASS'Y - SIDE AV BD 41-WJ0070-B00 WIRE BARE JUMPER 7MM C 2 J952, J953
08-02927T-AVY ASS'Y - SIDE AV BD 47-RCA041-XX0 JACK RCA 3PH H=8MM YL WH RD/SW C 1 P951
08-29274T-FCN ASS'Y - FRONT CABINET 02-GND029-XX0 ASS'Y-CRT GND WIRE & HOUS.(29) C 1
08-29274T-FCN ASS'Y - FRONT CABINET 36-294960-017 DEGAUSSING XC-74A-3100-TCL 29" C 1
08-29274T-FCN ASS'Y - FRONT CABINET 44-29NFLS-YX4A CRT 73SX707Y22-DC01 (AUST) H 1 CRT01
08-29274T-FCN ASS'Y - FRONT CABINET 46-14026H-02X HS 2P24 570/7 F/W S11-02H C 1 P601H FOR M. BD P601
08-29274T-FCN ASS'Y - FRONT CABINET 54-113971-0UE PVC TUBE #6 L=160MM H 2 FOR SPK HOUSING

HOUS.

P2-P7 FOR M. BD

P003

21

Sheet1

R

T

T

T

T

T

T

T

X

08-29274T-FCN ASS'Y - FRONT CABINET 63-H60300-0B4 S/T SCREW H 6 X 30 B C 4 MTG CRT & FRONT CAB.
08-29274T-FCN ASS'Y - FRONT CABINET 63-W30100-AB4 S/T SCREW W 3 X 10 AB C 1 MTG LENS & FRONT CAB.
08-29274T-FCN ASS'Y - FRONT CABINET 63-W30100-AB4 S/T SCREW W 3 X 10 AB C 3 MTG PUSH BUTTON & FRONT CAB.
08-29274T-FCN ASS'Y - FRONT CABINET 63-W30140-HS4 S/T SCREW W 3 X 14 HS C 8 MTG SPK & FRONT CAB.
08-29274T-FCN ASS'Y - FRONT CABINET 65-A60180-20E EXT. TOOTH WASHTER 6 X 18 X 2 C 4 FOR CRT & FRONT CAB.
08-29274T-FCN ASS'Y - FRONT CABINET 59-130460-00X RUBBER PAD (25MMX7MM) C 4 FOR CRT & SPK
08-29274T-FCN ASS'Y - FRONT CABINET 62-216340-0UA HOLDER POWER CORD C 1
08-29274T-FCN ASS'Y - FRONT CABINET 63-B30080-BT4 S/T SCREW 3 X 8 BT C 2 MTG SIDE AV BD & FRONT CAB.
08-29274T-FCN ASS'Y - FRONT CABINET 42-81608F-XX1 SPEAKER (80MMX160MM) 8 OHM 8W C 2 SP601, SP602
08-29274T-FCN ASS'Y - FRONT CABINET 46-27580H-02X HS 2P22 600/7 F/W TJC3-2Y C 1 P602H FOR M. BD P602
08-29274T-FCN ASS'Y - FRONT CABINET 54-205140-000 SPACER CRT MOUNTING T=2MM C 4 MTG. CRT TO F.CAB
08-29274T-FCN ASS'Y - FRONT CABINET 54-314740-0X0 CRT FIBRE SHEET T=0.8MM C 4
08-29274T-FCN ASS'Y - FRONT CABINET 59-130460-00X RUBBER PAD (25MMX7MM) C 2 STICK ON F. CAB.(FOOTING)
08-29274T-FCN ASS'Y - FRONT CABINET 59-312160-000 SPONGE CUSHION C 8
08-29274T-FCN ASS'Y - FRONT CABINET 62-10654X-00F UNI - TIE (2.5MMX95MM) C 13
08-29274T-FCN ASS'Y - FRONT CABINET 67-216790-0E0 SPRING CRT 6MMX50MMX0.6MM C 2
08-29274T-FCN ASS'Y - FRONT CABINET 67-242830-0E0 SPRING POWER KNOB C 1
08-29274T-FCN ASS'Y - FRONT CABINET 55-2927FC-0AN FRONT CABINET (94V-0 100%) C 1
08-29274T-FCN ASS'Y - FRONT CABINET 56-2927LE-0HC LENS - SENSO
08-29274T-FCN ASS'Y - FRONT CABINET 58-2927SI-3UI INLAY SIDE AV (RCA-3) C 1
08-29274T-FCN ASS'Y - FRONT CABINET 56-2927PK-1HA POWER KN0B C 1
08-29274T-FCN ASS'Y - FRONT CABINET 56-2927FB-1HA PUSH BUTTON C 1
08-29274T-RCN ASS'Y - REAR CABINE
08-29274T-RCN ASS'Y - REAR CABINE
08-29274T-RCN ASS'Y - REAR CABINE
08-29274T-RCN ASS'Y - REAR CABINE
08-29274T-RCN ASS'Y - REAR CABINE
08-29274T-RCN ASS'Y - REAR CABINE
08-29274T-RCN ASS'Y - REAR CABINE
08-29274T-PAN ASS'Y - PACKING 72-29274T-E03 OPERATION MANUAL C 1
08-29274T-PAN ASS'Y - PACKING 74-022032-6WE POLYBAG (22CMX32CMX0.06MM) C 1
08-29274T-PAN ASS'Y - PACKING 74-130130-80HAA POLYBAG W/SUFFOCATION WARNING C 1
08-29274T-PAN ASS'Y - PACKING 75-2927LR-CC0 POLYFOAM (LR) C 1
08-29274T-PAN ASS'Y - PACKING 75-2927LL-CC0 POLYFOAM "LL" C 1
08-29274T-PAN ASS'Y - PACKING 75-2927UL-CC0 POLYFOAM "UL" C 1
08-29274T-PAN ASS'Y - PACKING 75-2927UR-CC0 POLYFOAM "UR" C 1
08-29274T-PAN ASS'Y - PACKING 76-A2927U-0AT CARTON BOX C 1
08-29274T-PAN ASS'Y - PACKING 49-341790-BAT BATTERY AA SIZE C 2
08-02918T-NIY ASS'Y - NICAM BD 13-P3410G-8BP IC MSP 3410G B8 H 1 IC1001
08-02918T-NIY ASS'Y - NICAM BD 18-CB0102-JNX RES. C.F. 1K OHM 1/6W +/-5% C 2 R1022, R1023
08-02918T-NIY ASS'Y - NICAM BD 18-CB0152-JNX RES. C.F. 1.5K OHM 1/6W +/-5% C 1 R1002
08-02918T-NIY ASS'Y - NICAM BD 18-CB0332-JNX RES. C.F. 3.3K OHM 1/6W +/-5% C 1 R1003
08-02918T-NIY ASS'Y - NICAM BD 18-CB0470-JNX RES. C.F. 47 OHM 1/6W +/-5% C 1 R1001
08-02918T-NIY ASS'Y - NICAM BD 18-CB0472-JNX RES. C.F. 4.7K OHM 1/6W +/-5% C 3 R1019, R1020, R1021
08-02918T-NIY ASS'Y - NICAM BD 25-BCB470-M1X CAP. ELEC 47 UF 16V +/-20% C 2 C1001, C1013
08-02918T-NIY ASS'Y - NICAM BD 25-BFB109-M1X CAP. ELEC 1 UF 50V +/-20% C 1 C1005
08-02918T-NIY ASS'Y - NICAM BD 25-BFB339-M1X CAP. ELEC 3.3 UF 50V +/-20% C 1 C1020
08-02918T-NIY ASS'Y - NICAM BD 26-ABC152-KBX CAP. CER 1500 PF 50V +/-10% B C 1 C1017
08-02918T-NIY ASS'Y - NICAM BD 26-ABC272-KBX CAP. CER 2700 PF 50V +/-10% B C 2 C1006, C1007
08-02918T-NIY ASS'Y - NICAM BD 26-ABC339-CZX CAP. CER 3.3 PF 50V +/-0.25 SL C 2 C1026, C1027
08-02918T-NIY ASS'Y - NICAM BD 26-EBP102-KB

54-114000-00X FELT TAPE 150X19MM C 10 STICK ON REAR CAB.
55-2975RC-1AN REAR CABINET (94V-0 100%) C 1
58-2927RI-2UI INLAY TERMINAL BD C 1
58-2927MP-0UI PLATE MODEL NO. C 1
59-130460-00X RUBBER PAD (25MMX7MM) C 2 FOR REAR CAB. BUTTOM
63-B40200-AB3 S/T SCREW B 4 X 20 AB C 11 MTG FRONT & REAR CAB.
63-F30100-BT3 S/T SCREW F 3 X 10 BT (BLACK) C 2 MTG RCA JACK & REAR CAB.

CAP. CER 1000 PF 50V +/-10% B H 4 C1008, C1009, C1010, C1011

C1

22

Sheet1

08-02918T-NIY ASS'Y - NICAM BD 26-EBP103-ZFX CAP. CER 0.01UF 50V +80-20% F H 1 C1002
08-02918T-NIY ASS'Y - NICAM BD 26-EBP104-ZFX CAP. CER 0.1UF 50V +80-20% F H 5 C1004, C1012, C1019, C1021, C1023
08-02918T-NIY ASS'Y - NICAM BD 26-EBP471-JCX CAP. CER 470 PF 50V +/-5% CH H 1 C1018
08-02918T-NIY ASS'Y - NICAM BD 26-EBP560-JCX CAP CER 56PF 50V +/-5% CH H 3 C1024, C1025, C1028
08-02918T-NIY ASS'Y - NICAM BD 27-MBC334-J0X CAP. M.P.E 0.33UF 50V +/-5% C 2 C1029, C1030
08-02918T-NIY ASS'Y - NICAM BD 27-PBC102-J0X CAP. P.E. 1000 PF 50V +/-5% C 1 C1031
08-02918T-NIY ASS'Y - NICAM BD 34-R100J2-0EX COIL PL - 10 UH +/-5% C 1 L1001
08-02918T-NIY ASS'Y - NICAM BD 40-2918NT-NIB P.C.B. NICAM BD C 1
08-02918T-NIY ASS'Y - NICAM BD 41-WJ0060-B00 WIRE BARE JUMPER 6MM C 1 J1011
08-02918T-NIY ASS'Y - NICAM BD 41-WJ0065-B00 WIRE BARE JUMPER 6.5MM C 2 J1003, J1014
08-02918T-NIY ASS'Y - NICAM BD 41-WJ0075-B00 WIRE BARE JUMPER 7.5MM C 2 J1001, J1002
08-02918T-NIY ASS'Y - NICAM BD 41-WJ0090-B00 WIRE BARE JUMPER 9MM C 4 J1009, J1010, J1012, J1013
08-02918T-NIY ASS'Y - NICAM BD 45-OSC18M-4Y0 CRYSTAL 18.432M C 1 X1001
08-02918T-NIY ASS'Y - NICAM BD 46-21550W-12X HEADER *12 TS12B-SQ-1 L=10MM C 1 P1001 FOR M.BD P1200
08-02918T-NIY ASS'Y - NICAM BD 46-12866W-02X PIN BASE *2 S11-02W C 1 P1003
08-02918T-NIY ASS'Y - NICAM BD 67-257870-1T0 BRACKET IF BD C 1
08-02918T-NIY ASS'Y - NICAM BD 67-257870-2T0 BRACKET IF BD C 1
08-02918T-NIY ASS'Y - NICAM BD 18-CB0224-JNX RES. C.F. 220K OHM 1/6W +/-5% C 2 R1006, R1008
08-02918T-NIY ASS'Y - NICAM BD 11-SC1815-YBX TRANSISTOR 2SC1815Y C 3 Q1001, Q1002, Q1003

08-02918T-NIY ASS'Y - NICAM BD 41-WJ0150-B00 WIRE BARE JUMPER 15MM C 6
08-02918T-NIY ASS'Y - NICAM BD 25-BCB100-M1X CAP. ELEC 10 UF 16V +/-20% C 7

08-02918T-NIY ASS'Y - NICAM BD 25-BCB220-M1X CAP. ELEC 22 UF 16V +/-20% C 1 C1032
08-02918T-NIY ASS'Y - NICAM BD 18-CB0101-JNX RES. C.F. 100 OHM 1/6W +/-5% C 4 R1011, R1014, R1017, R1018
08-HS46F0-M13C ASS'Y - IR HANDSET (NI/BG/SW) 67-26968X-0E2 BATT. TERMINAL (+/-) C 1
08-HS46F0-M13C ASS'Y - IR HANDSET (NI/BG/SW) 67-310280-0E2 SPRING - BATTERY (-) C 1
08-HS46F0-M13C ASS'Y - IR HANDSET (NI/BG/SW) 67-310290-0E2 SPRING - BATTERY (+) C 1
08-HS46F0-M13C ASS'Y - IR HANDSET (NI/BG/SW) 74-009022-60C POLYBAG HANDSET (9CMX22CM) C 1
08-HS46F0-M13C ASS'Y - IR HANDSET (NI/BG/SW) 49-HS46F0-00X RUBBER PAD KEYS C 1
08-HS46F0-M13C ASS'Y - IR HANDSET (NI/BG/SW) 55-HS46FB-0HA CASE LOWER - REMOTE HANDSET C 1
08-HS46F0-M13C ASS'Y - IR HANDSET (NI/BG/SW) 55-HS46FD-0HA DOOR BATT. - REMOTE HANDSET C 1
08-HS46F0-M13C ASS'Y - IR HANDSET (NI/BG/SW) 55-HS46FT-0HA CASE UPPER - REMOTE HANDSET C 1
08-HS46F0-M13C ASS'Y - IR HANDSET (NI/BG/SW) 58-HS46F2-MUI INLAY IR TRANS.BD (NI/BG/SW) C 1
08-HS46F0-M13C ASS'Y - IR HANDSET (NI/BG/SW) 18-CB0229-JNX RES. C.F. 2.2 OHM 1/6W +/-5% C 1 R1502
08-HS46F0-M13C ASS'Y - IR HANDSET (NI/BG/SW) 18-CB0682-JNX RES. C.F. 6.8K OHM 1/6W +/-5% C 1 R1501
08-HS46F0-M13C ASS'Y - IR HANDSET (NI/BG/SW) 40-2909NT-RMB P.C.B. REMOTE HANDSET C 1
08-HS46F0-M13C ASS'Y - IR HANDSET (NI/BG/SW) 10-1N4148-ABX DIODE 1N4148 (SWITCHING) C 5 D1502, D1503, D1504, D1505, D1507
08-HS46F0-M13C ASS'Y - IR HANDSET (NI/BG/SW) 11-0BC337-0BX TRANSISTOR BC337-40 (NPN) C 1 Q1501
08-HS46F0-M13C ASS'Y - IR HANDSET (NI/BG/SW) 14-IRE05B-XX0 INFARED EMITTING DIODE C 1 D1501
08-HS46F0-M13C ASS'Y - IR HANDSET (NI/BG/SW) 25-HBB470-M1X CAP. ELEC 47UF 10V +/-20% C 1 C1503
08-HS46F0-M13C ASS'Y - IR HANDSET (NI/BG/SW) 26-EBP101-JCX CAP. CER 100 PF 50V +/-5% CH H 2 C1501, C1502
08-HS46F0-M13C ASS'Y - IR HANDSET (NI/BG/SW) 45-COS455-KY0 CER RESONATOR 455 KHZ C 1 X1501
08-HS46F0-M13C ASS'Y - IR HANDSET (NI/BG/SW) 63-B26060-BT2 S/T SCREW B 2.6 X 6 BT C 1
08-HS46F0-M13C ASS'Y - IR HANDSET (NI/BG/SW) 13-TC9028-23B IC TC9028-023 (IR TRANS.) 1 IC1501

J1004, J1005, J1006, J1007, J1008,
J1015

C1003, C1014, C1015, C1016, C1022,
C1033, C1034

23

TB1240 + TCLM13 chassis alignment instruction

f

Enter factory mode in productio n line

Simply press the D-mode key on the factory remote handset.

Enter service mode

Press and hold the VOLUME DOWN key tightly on the unit until minimum level and don’t release the
VOLUMN DOWN key, then press the DISPLAY key on the remote handset three times.

“D” letter on the screen indicated that the factory mode was entered. Now you can use the shortcut key
to access the factory menu. All change in factory data will save in EEPROM automatically

Note:

1. You can disable the D-Mode k ey (on factory remote handset) b y change “BIT-0” of “MODE2” to

“0”. If the D-Mode key was disabled, you can’t enter D-Mode by the D-mode key on the factory
remote (but you can still enter service mode). It is suggested to disable the D-Mod e key b efore the
set leave the factory.

2. On the factory remote handset, you can find the “BUS OFF” key. It can cut off the I2C control from

the CPU to other IC. This is only useful when automatic adjustment of white balance.

3. All system data in menu of “key 7” must keep unchanged when servicing. Othe rwise, the set may not

work properly.

Setting method:

No Adjustment

Items

1 Screen

voltage

2 Focus voltage ------------ Cross hatch

3 VCO ------------ Apply an IF

Data Name (default

value inside blanket)

------------ “IRGB cut off”

Conditions and

input signal

must set to 80 (all

signal (see tuner

frequency) to the

pattern)

pattern.

spec. For

IF input.

Setting method (need enter D-mode)

 Press “MUTE” key on the remote handset

and the screen will become a horizontal
line. Then adjust the “screen” VR on the
flyback until the horizontal line can just be
seen (minimum visible intensity).

 Adjust the “focus” VR on the flyback until

the screen becomes clear.

 Monitor the DC voltage at pin 48 o

IC201, then adjust T271 until the voltage at
pin 48 become 4.62 +/- 0.02 V.

 Press the AFT button on the factory remote

and AFT adjustment will be done
automatically.

4 Vertical

f

f

geometry for

PAL system

(Key 2)

VPOS50 (04)
HIGH50 (25)

VLIN50 (04)

VSC50 (05)
OSD50 (20)

Input a PAL cross

hatch pattern.

 Adjust VPOS50 for vertical position.
 Adjust HIGH50 for vertical amplitude.
 Adjust VLIN50 for vertical linearity.
 Adjust VSC50 for vertical S-correction
 Adjust OSD50 for OSD position (normally

use default value).

5 Vertical

geometry for

NTSC system

(Key 3)

6 Horizontal

geometry for

PAL system

(Key 4)

7 Horizontal

geometry for

NTSC system

(Key 5)

VPOS60 (00)

HIGH60 (2E)

VLIN60 (05)

VSC60 (0A)

OSD60 (89)

HPOS50 (0D)

HSIZE50 (2A)

PARA50 (14)

TRAP50 (0E)

CORN50 (0A)

VEHT50 (03)
HEHT50 (02)

HPOS60 (11)

HSIZE60 (2A)

PARA60 (18)

TRAP60 (0D)

CORN60 (0D)

VEHT60 (03)
HEHT60 (02)

Input a NTSC

cross hatch

pattern.

Input a PAL cross
hatch pattern with

black and white

background.

Input a NTSC

cross hatch

pattern with black

and white

background.

 Adjust VPOS60 for vertical position.
 Adjust HIGH60 for vertical amplitude.
 Adjust VLIN60 for vertical linearity.
 Adjust VSC60 for vertical S-correction
 Adjust OSD60 for OSD position (normally

use default value).

 Adjust HPOS50 for horizontal position.
 Adjust HSIZE50 for horizontal width.
 Adjust PARA50, TRAP50 and CORN50

until the vertical line at left and right side
of the picture become straight.

 VEHT and HENT is for the picture size

stability when changing the brightness o
the screen. Receive pattern of cross hatch
with black background and then change to
white background, then compare the
vertical and horizontal size between black
and white background. Adjust VEHT and
HEHT until you get the minimum
difference of screen size. After you adjust
VEHT and HEHT, you must re-adjust
vertical and horizontal amplitude.

 Adjust HPOS60 for horizontal position.
 Adjust HSIZE60 for horizontal width.
 Adjust PARA60, TRAP60 and CORN60

until the vertical line at left and right side
of the picture become straight.

 Adjust VEHT and HEHT using same

method of PAL system. Also need re­adjustment of vertical and horizontal
amplitude.

1

2

adjustment)

Key 6

(Status

RFAGC (25)
PIFAFT (44)

HAFC (00)
S-B-Y (08)

S-R-Y (08)
VOL 05 (48)
VOL 25 (65)
VOL OUT(73)

Receive a 60dB

grey scale + color

bar signal

 RFAGC – monitor the voltage at AGC pin

of the tuner. Then increase the setting o
RFAGC until the tuner AGC voltage reach
maximum (about 5V). Then decrease the
RFAGC setting until the AGC voltage just
drop.

 Adjust S-B-Y and S-R-Y to get the optimal

color for SECAM system.

 Please keep the PIFAFT value after auto

AFT adjustment.

 HAFC item must use the default value.

(curve of

volume
control)

---------  VOL05 is the volume output level at 5%
 VOL25 is the volume output level at 25%

Remark: The value of VOL05 and VOL25 was
not suggested to vary in every set. It is
suggested to use the default value.

13 White balance

adjustment

(key 1)

R CUT (6B)
G CUT (9E)
B CUT (7C)
G DRV (39)
B DRV (35)

Black and white

pattern (PAL)

1. Measure the dark side of the picture with a

color analyzer and set RCUT to 80. Then
adjust BCUT and GCUT until the data on
the analyzer become x = 284, y = 299.

2. Measure the bright side of the picture,

Then adjust BDRV and GDRV until the
data on the analyzer become x = 284, y =

299.

3. Repeat step 1 and 2 until you get right

color on both dark and bright side of the
screen.

Other adjustment (default value was suggested, except BRTC)

8Key 0 OSD (0A)

TXCX (30)

RGCN (20)

TNTX (25)
TNTN (32)

FMMODE (13)

DKFMMD (20)

9Key 8 SCNT (0F)

CNTX (3F)
CNTN (00)

BRTX (20)

BRTN (25)
COLX (35)
COLN (00)

10 Key 9 CNTC (22)

BRTC (37)

COLC (50)

TNTC (35)

COLP (00)

COLS (54)

BRTS (00)

---------- OSD – OSD position
TXCX – OSD intensity when maximum

contrast

RGCN – OSD intensity when minimum

contrast
TNTX – maximum tint level
TNTN – minimum tint level
FMMODE – frequency shift for FM (mono)

mode, only useful for NICAM

model
DKFMMD - frequency shift for DK NICAM

mode

---------- SCNT – sub contrast for luminance signal
CNTX – maximum contrast
CNTN – minimum contrast
BRTX – maximum brightness
BRTN – minimum brightness
COLX – maximum color
COLN – minimum color

---------- CNTC – 50% contrast
BRTC – 50% brightness
COLC – 50% color
TNTC – 50% tint
COLP – color level for PAL
COLS – color level for SECAM
BRTS – sub brightness for SECAM

 For the adjustment of BRTC, receive an 8

step grey scale pattern and adjust all
picture settings to 50%. Then adjust B RTC
until the first and second step on the screen
can just be distinguished.

11 Two digit key

-/--

(sharpness

adjustment)

13 KEY CALL DBE STR 50

SHPTV3 (1A)

SHPAV3 (1A)
SHPTV4 (18)

SHPAV4 (18)

SHPX (1A)

SHPN (1F)

DBE HMC 0D
DBE HP 07
DBE LP 00
DBE LIM FO
SUB FRE 15
SUB HP 02
VOLMAI 03

System data:

Item Adjust item Default value

---------- SHPTV3 – 50% sharpness in 3.58 system
(TV)
SHP AV3 – 50% sharpness in 3.58 system (AV)
SHPTV4 – 50% sharpness in 4.43 system
(TV)
SHP AV4 – 50% sharpness in 4.43 system (AV)
SHPX – maximum sharpness
SHPN – minimum sharpness

Richly Music

Signal

Effect Strength
Harmonic Content
High Pass Corner Frequency
Low Pass Corner Frequency
Amplitude Limit
Subwoofer Corner Frequency
Subwoofer Complementary High Pass Filter
Volume Loudspeaker

12 Key 7 VCDM0

VCDM1
VCDM2
MODE0
MODE1
MODE2

OPTION

It is subject to the current ODF.
Please check the sample to get the value.

System setting of M13

VCDM0 (default value: 28)

BIT Item

0 System switch: 0 : normal identify mode 1 : weak signal identify mode
1 White peak suppress: 0: on 1: off

ABL gain

2,3

00: -0.74v 01: -0.64v 10: -0.37v 11: -0.12v
ABL start point

4,5

00: -0.01v 01: -0.11v 10: -0.3v 11: -0.45v

6 CW-SW: TB1238N, pin 29 Fsc CW output 0 : AUTO, 1 : 4.43M

In force system mode, the status of color killer when weak signal

7

0: on 1: off

VCDM1 (default value: 00)

BIT Item

0 Blanking: 0: on 1: off

1,2,3,4,5 V-Mute timing: = 200ms + 8ms ×Data

6 Base band filter in NTSC system: 0: on, 1: off
7VMOD

VCDM2 (default value: 40 for 38MHz IF, 30 for 38.9MHz IF)
BIT Item

0 AFT-mute: 0: off, 1: on (brightness off)
1 SECAM-ADJ: 0: SECAM correction off, 1: SECAM correction on
2 TB1238N_VMOD

3 PIF VCO ADJ
6,5,4 IF frequency:

111: 33.9MHz 110: 33.95MHz 101: 34.47MHz 100: 38MHz
011: 38.9MHz 010: 39.5MHz 001: 45.75MHz 000: 58.75MHz

7 No use

MODE0

BIT Item
0 0: normal AV 1: SCART (CATV)

1 SRS: 0: OFF 1:ON
2 SECAM system: 0: off, 1: on

3 High Sensibility: 0: off 1: on
4, 5 STANDBY status after switch on : 00 or 10: force STANDBY

01: force on. 11: status before switch off

6,7 Mode0.6, Mode0.7: 0X: English 10: English + Russia 11: English + Vietnamese

MODE1

BIT Item
0 BG : 0 : off 1 : on
1 I : 0 : off 1 : on
2 DK : 0 : off 1 : on
3 M : 0 : off 1 : on
4, 5 SSIF1, SSIFO Default sound system after auto search:

00 : BG 01 : I 10 : DK 11 : M

6 AV/TV: 0: TV/AV 1: TV AV1/AV2
7 Number of channels: 0: 50 1: 100

MODE2

BIT Item
0 D-MODE : 0: off 1: on
1 Teletext 0: off 1: on
2 COMB Filter 0: off 1: on
3 BBE 0: off 1: on
4 NICAM & IGR 0: off 1: on
5 WOOFER 0: off 1: on
6 DBE 0: off 1: on
7 VM 0: off 1: on

OPTION (default value: 10)

BIT Item
0 When blue background off (mute pin of CPU):

0: audio mute on 1: audio mute off

1 When blue background off (external mute pin of CPU):

0: audio mute on 1: audio mute off

2 When change channel:

0: picture mute on 1: picture mute off

3 Audio demodulation gain setting:

0: 50KHz 1: 25KHz

4 When no signal:

0: search channel by changing VT 1: use memorized VT

5 Logo: 0: off 1: on
6 OSD black background: 0: off 1: on
7 Display on Sound Mode Changing:

0: on 1: off