Teac CD-200BT User Manual
CD-200BT
CD Player / Bluetooth Receiver
OWNER'S MANUAL
D01194420A
IMPORTANT SAFETY PRECAUTIONS
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol, within equilateral triangle, is intended to alert
the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING: TO PREVENT FIRE OR
SHOCK HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
For U.S.A. / CANADA model
Compliance statement
This device complies with “Part 15 of FCC Rules” and “RSSGen of IC Rules”.
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including
interference that may cause undesired operation of this
device.
INFORMATION TO THE USER
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when
the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user
will be required to correct the interference at his own
expense.
For CANADA
THIS CLASS A DIGITAL APPARATUS COMPLIES WITH
CANADIAN ICES-003.CET
APPAREIL NUMERIQUE DE LA CLASSE A EST CONFORME A
LA NORME NMB-003 DU CANADA.
CAUTION
Changes or modifications to this equipment not expressly
approved by TEAC CORPORATION for compliance could
void the user's authority to operate this equipment.
DECLARATION OF CONFORMITY
We, TEAC EUROPE GmbH. Bahnstrasse 12, 65205
Wiesbaden-Erbenheim, Germany declare in own
responsibility, the TEAC product described in this
manual is in compliance with the corresponding
technical standards.
CE Marking Information
a) Applicable electromagnetic environment: E4
b) The average half-cycle r.m.s. inrush current
1. On initial switch-on: 0.29 Arms
2. After a supply interruption of 5s: 0.15 Arms
For the customers in Europe
WARNING
This is a Class A product. In a domestic environment, this
product may cause radio interference in which case the
user may be required to take adequate measures.
Pour les utilisateurs en Europe
AVERTISSEMENT
Il s'agit d'un produit de Classe A. Dans un environnement
domestique, cet appareil peut provoquer des
interférences radio, dans ce cas l'utilisateur peut être
amené à prendre des mesures appropriées.
Für Kunden in Europa
Warnung
Dies ist eine Einrichtung, welche die Funk-Entstörung
nach Klasse A besitzt. Diese Einrichtung kann im
Wohnbereich Funkstörungen versursachen; in diesem
Fall kann vom Betrieber verlang werden, angemessene
Maßnahmen durchzuführen und dafür aufzukommen.
Radiation Exposure Statement
This equipment complies with FCC/IC radiation exposure
limits set forth for an uncontrolled environment, meets
“the FCC radio frequency Exposure Guidelines”, and “RSS102 of the IC radio frequency (RF) Exposure rules”.
End-users and installers must be provided with antenna
installation instructions and transmitter operating conditions for satisfying RF exposure compliance.
Note (Conditions of conformity)
This equipment should be installed and operated with
minimum distance 20cm between the radiator & your
body.
TASCAM CD-200BT
2
In North America use only on 120V supply.
This appliance has a serial number located on the rear panel.
Please record the model number and serial number and
retain them for your records.
Model number
Serial number
IMPORTANT SAFETY INSTRUCTIONS
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in
accordance with the manufacturer's instructions.
8 Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
ampliers) that produce heat.
9 Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. If the provided plug does not
t into your outlet, consult an electrician for replacement of the obsolete outlet.
10 Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11 Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand, tripod, bracket, or table
specied by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving
the cart/apparatus combination to avoid injury from
tip-over.
The apparatus draws nominal non-operating power
•
from the AC outlet with its POWER or STANDBY/ON
switch not in the ON position.
The mains plug is used as the disconnect device, the
•
disconnect device shall remain readily operable.
Caution should be taken when using earphones or
•
headphones with the product because excessive sound
pressure (volume) from earphones or headphones can
cause hearing loss.
If you are experiencing problems with this product,
•
contact TEAC for a service referral. Do not use the prod-
uct until it has been repaired.
CAUTION
Do not expose this apparatus to drips or splashes.
•
Do not place any objects filled with liquids, such as
•
vases, on the apparatus.
Do not install this apparatus in a confined space
•
such as a book case or similar unit.
The apparatus should be located close enough to
•
the AC outlet so that you can easily grasp the power
cord plug at any time.
If the product uses batteries (including a battery
•
pack or installed batteries), they should not be
exposed to sunshine, fire or excessive heat.
CAUTION for products that use replaceable lithium
•
batteries: there is danger of explosion if a battery is
replaced with an incorrect type of battery. Replace
only with the same or equivalent type.
8
RACK-MOUNTING THE UNIT
Use the supplied rack-mounting kit to mount the unit in a
standard 19-inch rack, as shown below.
Remove the feet of the unit before mounting.
13 Unplug this apparatus during lightning storms or
when unused for long periods of time.
14 Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
CAUTION
•
Leave 1U of space above the unit for ventilation.
•
Allow at least 10 cm (4 in) at the rear of the unit for
ventilation.
TASCAM CD-200BT
3
Safety Information
For U.S.A
8
CAUTIONS ABOUT BATTERIES
This product uses batteries. Misuse of batteries could
cause a leak, rupture or other trouble. Always abide by
the following precautions when using batteries.
Never recharge non-rechargeable batteries. The
•
batteries could rupture or leak, causing fire or injury.
When installing batteries, pay attention to the polarity
•
indications (plus/minus (+/–) orientation), and install
them correctly in the battery compartment as indicated. Putting them in backward could make the batteries
rupture or leak, causing fire, injury or stains around
them.
When you store or dispose batteries, isolate their termi-
•
nals with insulation tape or something like that to prevent
them from contacting other batteries or metallic objects.
When throwing used batteries away, follow the dispos-
•
al instructions indicated on the batteries and the local
disposal laws.
Do not use batteries other than those specified. Do not
•
mix and use new and old batteries or different types of
batteries together. The batteries could rupture or leak,
causing fire, injury or stains around them.
Do not carr y or store batteries together with small
•
metal objects. The batteries could short, causing leak,
rupture or other trouble.
Do not heat or disassemble batteries. Do not put them
•
in fire or water. Batteries could rupture or leak, causing
fire, injury or stains around them.
If the battery fluid leaks, wipe away any fluid on the
•
bat tery case before inserting new batteries. If the
battery fluid gets in an eye, it could cause loss of
eyesight. If fluid does enter an eye, wash it out thoroughly with clean water without rubbing the eye and
then consult a doctor immediately. If the fluid gets on
a person’s body or clothing, it could cause skin injuries
or burns. If this should happen, wash it off with clean
water and then consult a doctor immediately.
8
CAUTIONS ABOUT LASER RADIATION
This product has been designed and manufactured according
to FDA regulations “title 21, CFR, chapter 1, subchapter J, based
on the Radiation Control for Health and Safety Act of 1968,” and
is classified as a class 1 laser product. There is no hazardous
invisible laser radiation during operation because invisible laser
radiation emitted inside of this product is completely confined
in the protective housings.
The label required in this regulation is shown at 1.
1
Cautions:
DO NOT REMOVE THE PROTECTIVE HOUSING USING A
•
SCREWDRIVER.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
•
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION EXPOSURE.
IF THIS PRODUCT DEVELOPS TROUBLE, CONTACT YOUR
•
NEAREST QUALIFIED SERVICE PERSONNEL, AND DO NOT USE
THE PRODUCT IN ITS DAMAGED STATE.
Optical pickup
Type : EP-C101
Manufacturer : Ever Bright Technology and Science
Electronical Co.,LTD
Laser output : Less than 0.3 mW
Wavelength : 790±25nm
Standard : IEC60825-1: 2007
The unit power should be off when you install and
•
replace batteries.
Remove the batteries if you do not plan to use the unit
•
for a long time. Batteries could rupture or leak, causing
fire, injury or stains around them. If the battery fluid
leaks, wipe away any fluid on the battery compartment
before inserting new batteries.
Do not disassemble a battery. The acid inside the
•
battery could harm skin or clothing.
TASCAM CD-200BT
4
8
Pb, Hg, Cd
For European Customers
Disposal of electrical and electronic equipment
(a) All electrical and electronic equipment should be
disposed of separately from the municipal waste
stream via designated collection facilities appointed
by the government or the local authorities.
(b) By disposing of the electrical and electronic
equipment correctly, you will help save valuable
resources and prevent any potential negative effects
on human health and the environment.
(c) Improper disposal of waste equipment can have
serious effects on the environment and human health
as a result of the presence of hazardous substances in
electrical and electronic equipment.
(d) The crossed out wheeled dust bin symbol indicates
that electrical and electronic equipment must be
collected and disposed of separately from household
waste.
(e) The return and collection systems are available to
the end users. For more detailed information about
disposal of old electrical and electronic equipment,
please contact your city office, waste disposal service
or the shop where you purchased the equipment.
Safety Information
Disposal of batteries and/or accumulators
(a) Waste batteries and/or accumulators should be
disposed of separately from the municipal waste
stream via designated collection facilities appointed
by the government or the local authorities.
(b) By disposing of waste batteries and/or accumulators
correctly, you will help save valuable resources and
prevent any potential negative effects on human
health and the environment.
(c) Improper disposal of waste batteries and/or accumu-
lators can have serious effects on the environment
and human health as a result of the presence of
hazardous substances in batteries and/or accumulators.
(d) The crossed out wheeled dust bin symbol indicates
that batteries and/or accumulators must be collected
and disposed of separately from household waste.
If the battery or accumulator contains more than
the specified values of lead (Pb), mercury (Hg), and/
or cadmium (Cd) defined in the Battery Directive
(2006/66/EC), then the chemical symbols for lead (Pb),
mercury (Hg) and/or cadmium (Cd) will be indicated
beneath the crossed out wheeled dust bin symbol.
(e) The return and collection systems are available to
the end users. For more detailed information about
disposal of waste batteries and/or accumulators,
please contact your city office, waste disposal service
or the shop where you purchased them.
8
For China
“仅适用于海拔 2000m 以下地区安全使用”
“仅适用于非熱帯气候条件下安全使用”
产品有毒有害物质或元素的名称及含量
机种 ：CD-200BT 有毒有害物质或元素
品名
1 CHASSIS 部份 ○ ○ ○ ○ ○ ○
2 FRONT PANEL 部份 ○ ○ ○ ○ ○ ○
3 螺丝部份 ○ ○ ○ ○ ○ ○
4 线材部份 ○ ○ ○ ○ ○ ○
5 PCB Assy 部份 × ○ ○ ○ ○ ○
6 CD MECH 部份 ○ ○ ○ ○ ○ ○
7 电源部份 ○ ○ ○ ○ ○ ○
8 附属品部份 × ○ ○ ○ ○ ○
9 LABEL 部份 ○ ○ ○ ○ ○ ○
10 包装部份 ○ ○ ○ ○ ○ ○
○ ：表示该有毒有害物质在该部件所有均质材料中的含有量均在 SJ/T11363-2006 标准规定的限量要求以下。
× ：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求。
（针对现在代替技术困难的电子部品及合金中的铅 )
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr6+)
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
TASCAM CD-200BT
5
Contents
1 – Introduction ...................................................................... 7
Features .................................................................................. 7
Included items .....................................................................7
Conventions used in this manual ..................................7
Trademarks ............................................................................ 8
Precautions for placement ..............................................8
Power supply ........................................................................ 8
Beware of condensation ...................................................8
Cleaning the unit ................................................................. 8
About discs ............................................................................ 9
Handling of compact discs ....................................... 9
Bluetooth overview ............................................................ 9
Transmission conditions ............................................ 9
Profiles ............................................................................. 9
Codecs .............................................................................. 9
Content protection ...................................................... 9
Transmission security ................................................. 9
2 – Names and functions of parts .......................... 10
Top panel .............................................................................10
Rear panel ............................................................................ 11
Display ...................................................................................12
Remote control unit (TASCAM RC-CD200BT) ..........12
Setting the program .................................................20
Checking the program .............................................21
Replacing a program track .....................................21
Adding more program tracks ................................22
Clearing the program ...............................................22
Repeat playback ................................................................22
Time and text information display .............................23
Pitch control ........................................................................24
Intro Check function ........................................................ 24
5 – Bluetooth device playback .................................25
Pairing ...................................................................................25
Searching for Bluetooth devices .................................25
Controlling Bluetooth devices .....................................25
Playback from Bluetooth devices ................................25
Bluetooth information display .....................................26
Deleting pairing information ........................................26
6 – Message Lists ..................................................................27
Operation messages ........................................................27
Warning messages ...........................................................27
Error messages ...................................................................27
7 – Troubleshooting ..........................................................28
3 – Preparations .................................................................... 14
Making connections ........................................................14
Connecting a device to the AUX IN jack ...................15
Preparing the remote control ....................................... 15
Inserting batteries ......................................................15
Replacing the batteries ............................................15
Cautions about the use of batteries .................... 15
Cautions about using the remote control ......... 15
Loading a CD ......................................................................16
Selecting the audio to output (current source)......16
4 – CD playback .....................................................................17
Playable discs and files ................................................... 17
Folders and tracks on data CDs ................................... 17
Playback area .....................................................................18
Setting the playback area .......................................18
Playback modes .................................................................18
Selecting the playback mode ................................ 18
Playback................................................................................19
Selecting a track ................................................................ 19
Skipping to the next or previous track ............... 19
Selecting by track number .....................................19
Search forward and backward .....................................20
Folder playback (data CDs) ............................................20
Setting the playback folder ....................................20
Programmed playback ....................................................20
8 – Specifications ................................................................. 29
Ratings ..................................................................................29
Input and output ratings ................................................29
Analog audio input ....................................................29
Analog audio output ratings..................................29
Digital audio output ratings ...................................29
Audio performance ..........................................................29
Backup memory ................................................................ 29
Bluetooth .............................................................................29
General .................................................................................30
Dimensions .........................................................................30
TASCAM CD-200BT
6
1 – Introduction
Thank you for your purchase of the TASCAM CD-200BT CD Player
/ Bluetooth Receiver.
Before connecting and using the unit, please take time to read
this manual thoroughly to ensure you understand how to
properly set up and connect the unit, as well as the operation
of its many useful and convenient functions. After you have
finished reading this manual, please keep it in a safe place for
future reference.
You can also download the Owner's Manual from the TASCAM
web site (http://tascam.com).
Features
•
Plays back audio CDs (CD-DA) and data CDs (CD-ROM/R/
RW) with WAV, MP3 and MP2 format files.
•
2U rack mount size
•
Analog (RCA) and digital (coaxial and optical) outputs
•
Headphone output with level control
•
TASCAM RC-CD200BT remote control with number (0–9)
buttons included
•
Displays CD text and ID3 tag information (including artist,
album and track names)
•
4 playback modes (continuous, single, random and
program)
•
Repeat playback function can be turned ON and OFF
•
Playback area can be designated for data CDs (ALL PLAY or
FOLDER)
•
CD playback pitch control function (±14%)
•
Intro check function
•
Time can be displayed as track elapsed time, track
remaining time or total remaining time for audio CDs and as
track elapsed time for data CDs
•
CD drive has 10-second shockproof memory (protection
against skipping).
•
Built-in Bluetooth® audio receiver enables output of audio
from computers and portable audio devices that support
Bluetooth (A2DP)
•
In addition to SBC, Bluetooth (A2DP) supports AAC and
aptX® decoding, enabling the reception of high-quality
audio
•
Bluetooth (A2DP) also supports SCMS-T, enabling the
reception of protected audio content
•
Stereo line mini jack enables audio input from portable
audio players that do not support Bluetooth
Included items
This product includes the following items.
Take care when opening the package not to damage the items.
Keep the packing materials for transportation in the future.
Please contact TASCAM if any of these items are missing or have
been damaged during transportation.
• Main unit ................................................................................................. 1
• Wireless remote control unit (RC-CD200BT) .............................. 1
• AA batteries ............................................................................................ 2
• A rack-mounting screw kit............................................... ................. 1
• Warranty card ........................................................................................ 1
• Owner's Manual (this manual) ......................................................... 1
Conventions used in this manual
In this manual, we use the following conventions:
•
Buttons, connectors and other parts of the unit and external
devices are indicated like this: DISPLAY button
•
Text displayed on the display of the unit and external
devices appears like this: ON.
•
CD-DA format discs are sometimes called “audio CDs.”
•
CDs that contain audio files in MP2, MP3 or WAV formats are
called “data CDs.”
•
Audio CDs and data CDs are sometimes generically called
“CDs”.
•
MP3, MP2 and WAV files are sometimes generically called
"audio files".
•
The currently selected audio source is called the "current
source".
•
The currently selected folder is called the “current folder”.
•
The currently selected file is called the “current file”.
•
A computer, portable audio device or other equipment that
is connected to this unit by Bluetooth is called a "Bluetooth
device".
•
Additional information is provided as necessary as tips,
notes and cautions.
TIP
These are tips about how to use the unit.
NOTE
These provide additional explanations and describe special
cases.
CAUTION
Failure to follow these instructions could result in injury,
damage to equipment or lost recording data, for example.
TASCAM CD-200BT
7
1 – Introduction
Trademarks
•
TASCAM is a registered trademark of TEAC Corporation.
•
The Bluetooth® word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. and any use of
such marks by TEAC CORPORATION is under license.
•
© 2012 CSR plc and its group companies. The aptX® mark
and the aptX logo are trade marks of CSR plc or one of its
group companies and may be registered in one or more
jurisdictions.
•
MPEG Layer-3 audio coding technology licensed from
Fraunhofer IIS and Thomson.
•
Other company names, product names and logos in this
document are the trademarks or registered trademarks of
their respective owners.
Any data, including, but not limited to information,
described herein are intended only as illustrations of such
data and/or information and not as the specifications for
such data and/or information. TEAC Corporation disclaims
any warranty that any use of such data and/or information
shall be free from infringement of any third party’s intellectual property rights or other proprietary rights, and
further, assumes no liability of whatsoever nature in the
event of any such infringement, or arising from or connected
with or related to the use of such data and/or information.
This product is designed to help you record and reproduce
sound works to which you own the copyright, or where
you have obtained permission from the copyright holder or
the rightful licensor. Unless you own the copyright, or have
obtained the appropriate permission from the copyright
holder or the rightful licensor, your unauthorized recording,
reproduction or distribution thereof may result in severe
criminal penalties under copyright laws and international
copyright treaties. If you are uncertain about your rights,
contact your legal advisor. Under no circumstances will TEAC
Corporation be responsible for the consequences of any
illegal copying performed using the recorder.
Precautions for placement
•
The operating temperature should be between 5°C and
35°C (41°F and 95°F).
•
Make sure that the unit is mounted in a level position for
correct operation.
•
Do not place any object on the unit for heat dissipation.
•
Avoid installing this unit on top of any heat-generating
electrical device such as a power amplifier.
Power supply
Connect the unit to the standard power outlet. Hold the plug
when connecting and disconnecting the power cord.
Beware of condensation
If the unit is moved from a cold to a warm place, or used
immediately after a cold room has been heated or otherwise
exposed to a sudden temperature change, condensation could
occur. Should this happen, leave the unit for one or two hours
before turning the unit on.
Cleaning the unit
To clean the unit, wipe it gently with a soft dry cloth. Do not
wipe with chemical cleaning cloths, paint thinner, ethyl alcohol
or other chemical agents to clean the unit as they could damage
the surface.
Once every five years, please contact the retailer where you
purchased the unit or a TASCAM service center for internal
cleaning. If the unit is not cleaned for a long time and dust is
allowed to accumulate inside it, fire or malfunction could result.
Cleaning is more effective when conducted before the humid
season. Please check with us about the cost of internal cleaning.
TASCAM CD-200BT
8
1 – Introduction
About discs
In addition to audio CDs (CD-DA), the CD-200BT can play CD-R
and CD-RW discs on which audio CD, MP3, MP2 or WAV format
files are recorded. The CD player can also play 3-inch CDs.
Handling of compact discs
Always place the compact discs in the trays with their label
•
facing upward.
To remove a disc from its case, press down on the center of
•
the disc holder, then lift the disc out, holding it carefully by
the edges.
Do not touch the signal side (the unlabeled side).Fingerprints,
•
oils and other substances can cause errors during playing.
To clean the signal side of a disc, wipe gently with a soft dry
•
cloth from the center towards the outside edge. Dirt on discs
can lower the sound quality, so clean them and always store
them in a clean state.
Do not use any record spray, anti-static solutions, benzine,
•
paint thinner or other chemical agents to clean CDs. This
could damage the delicate playing surface and cause CDs to
become unplayable.
Do not apply labels or other materials to discs. Do not use
•
discs that have had tape, stickers or other materials applied
to their surface. Do not use discs that have sticky residue
from stickers, etc. Such discs could become stuck in the unit
or cause it to malfunction.
Never use a commercially available CD stabilizer. Using stabi-
•
lizers with this unit will damage the mechanism and cause it
to malfunction.
Do not use cracked discs.
•
Only use circular compact discs. Do not use non-circular
•
promotional, etc. discs.
Moreover, the use of a wireless LAN (IEEE802.11b/g) or
microwave oven in the same operating environment could also
interfere with Bluetooth transmission. If this occurs, stop using
that equipment or move this unit and the Bluetooth device at
least 10 m away from it.
Profiles
This unit supports the following Bluetooth profiles.
•
A2DP (Advanced Audio Distribution Profile)
•
AVRCP (Audio/Video Remote Control Profile)
Bluetooth devices must support A2DP in order to transmit audio
via Bluetooth.
Bluetooth devices must support AVRCP in order to enable
playback control via Bluetooth.
Even if they have the same Bluetooth profile, however, different
Bluetooth devices can have different functions depending on
their specifications.
Codecs
This unit supports the following A2DP codecs and automatically
selects one of them during audio transmission.
•
SBC
•
AAC
•
aptX
It will select the appropriate A2DP codec to use according to the
codec support of the Bluetooth device and transmission conditions.
NOTE
You cannot use buttons, for example, to select the A2DP
codec.
Due to the nature of Bluetooth wireless technology, playback
from this unit will start slightly later than when triggered from
the Bluetooth device.
Some record companies sell copy-protected discs or copy-
•
controlled discs that may not play back correctly in this unit.
Since such discs may not conform with the CD standard, do
not use them in this unit.
If you experience problems with such non-standard discs,
•
you should contact the producers of the disc.
Bluetooth overview
This unit has a built-in Bluetooth audio receiver, allowing it to
output the audio playback of a computer or portable audio
device that supports Bluetooth. In addition, this unit can be
used to control the playback of such Bluetooth devices.
CAUTION
Operation and connection of this unit's Bluetooth functions
with all Bluetooth devices are not guaranteed.
Transmission conditions
This is a Class 2 Bluetooth transmission output device. It has an
approximate transmission range of 10 m, but this distance can
vary due to the interference of obstacles and electromagnetic
waves.
An obstacle between this unit and another Bluetooth device
could interfere with Bluetooth transmission. If this occurs,
remove the obstacle.
Content protection
This unit supports SCMS-T content protection during audio
transmission, enabling the playback of protected audio.
Transmission security
This unit supports security functions during Bluetooth transmission according to the Bluetooth standards, but the invisibility
of transmission is not guaranteed.
Our company will take absolutely no responsibility if data is
leaked during Bluetooth transmission.
TASCAM CD-200BT
9
2 – Names and functions of parts
Top panel
1 POWER switch
Press this switch to turn the unit on or off.
CAUTION
•
Before turning the power on, minimize the volume of
connected equipment. Failure to do so could cause sudden
loud noises, which might harm your hearing, for example.
•
Do not wear headphones when turning the power ON/OFF.
Noise could damage speakers or your hearing.
2 Disc tray
Insert discs (CD, CD-R, CD-RW) here.
3 OPEN/CLOSE button
Use to open and close the disc tray.
4 PLAY/PAUSE button
Press during playback to pause. When playback is stopped or
paused, press to start playback.
5 STOP button
Press this button to stop playback.
Press this button when editing a program to clear all items
added to the program. (See “Setting the program” on page
20.)
6 SEARCH m/,[.//] buttons
Press briefly to select tracks (skip). Press and hold to search a
track.
7 PHONES jack and knob
Use this standard stereo jack to connect stereo headphones.
Use a plug adapter when connecting headphones with
mini-plugs. Use the PHONES knob to adjust the headphone
output level.
seconds. Press this button again briefly during this time
to change the device to be connected by Bluetooth. (See
“Searching for Bluetooth devices” on page 25.)
Press and hold this button to start Bluetooth pairing mode.
Press and hold this button when in pairing mode to end
pairing mode. (See “Pairing” on page 25.)
0 Display
Displays various information.
q Remote Sensor
When operating the remote control unit (RC-CD200BT),
point it towards here.
w DISPLAY [SHIFT] button
You can change the time and other information shown on
this display.
When this button is pressed, the type of information
currently displayed is shown for two seconds. Press the
button again during this time to change the type of information shown. The information that can be shown depends
on the current source, type of media and the status of
operation. (See “Time and text information display” on page
23.) (See “Bluetooth information display” on page 26.)
Press this button at the same time as another button to use
its shift function, which is shown as black letters on a white
background beneath the button.
CAUTION
Use the PHONES knob to minimize the volume before
connecting headphones. Failure to do so could cause a
sudden burst of loud noise, which might result in hearing
damage, for example.
8 AUX IN jack
Use this stereo mini jack for line level audio input.
Connect a portable digital audio player or other external
audio device to it.
CAUTION
Before connecting an external device to the AUX IN jack,
minimize the volume of that device. Failure to do so could
result in sudden loud noises that could, for example, harm
your hearing.
9 DEVICE SEL/PAIRING button
Press this button briefly to show the name of the device
connected (or ready to be connected) by Bluetooth for two
TASCAM CD-200BT
10
Loading...