Taotronics DOTR1068 user guide

Page 1
尺寸:150*160mm
Model:
装订成册 材质:封面128克铜版纸 内页80克书纸
HM-AH003
Page 2
Rev_1.3_EN
E-MAIL
support@homech.net
MANUFACTURER
Manufacturer: Shenzhen NearbyExpress Technology Development Co.,Ltd. Address: Floor 7, Building E, Galaxy World Phase II, Shenzhen, China
MODEL: HMAH003
ULTRASONIC COOL MIST HUMIDIFIER
User Manual
Page 3
CONTENTS
STATEMENT
SAFETY INSTRUCTIONS
BEFORE USING THE HUMIDIFIER
WHEN USING THE HUMIDIFIER
AFTER USING THE HUMIDIFIER
PACKAGE CONTENTS
SPECIFICATIONS
PRODUCT DIAGRAM
OPERATIONS AND FUNCTIONS
Add Water
Power On / O
Light Control
Low Water Protection: Auto Shut-o the Humidier
CLEANING AND MAINTENANCE
Caution
Daily Maintenance
Weekly Maintenance
Scale Removal Instructions
Disinfecting Instructions
Clean the Dustproof Sponge
End-Of-Season Care and Storage
TROUBLESHOOTING GUIDE
WARRANTY
HOMECH CUSTOMER CARE
01
01
02
03
04
05
05
06
07
07
08
08
08
09
09
09
09
10
11
12
12
13/15
16
16
Page 4
STATEMENT
Thank you for purchasing a Homech product that has been tested to meet our stringent quality standards. This product is covered with Homech product and labor warranty for 12 months from the date of its original purchase.
Please email us with your order ID and problem or issue, we will respond within 24 hours.
Please read the User Manual thoroughly. Clean and maintain the product as instructed. If any abnormalities occur, please refer to the Troubleshooting Guide rst.
This warranty is void if the defect is caused by accidental damage, misuse, abuse, neglect, improper repair or alteration by unauthorized persons, or a failure to follow operating instructions provided with the product including adding essential oils directly into the tank and base. This warranty does not apply to normal wear and tear or commercial use.
In no event shall liability exceed the purchase price paid by the purchaser of the product. Under no circumstances shall there be liability for any loss – direct, indirect or incidental – or consequential damage arising out of, or in connection with the use of the product.
BEFORE USING THE HUMIDIFIER
1 2
1. Please check the cord for any signs of damage.Do not use the humidier if the cord has been damaged.
2. DO NOT place this humidier in wet environments.
Please always keep the humidier out of reach of patients & children & pet.
SAFETY INSTRUCTIONS
The humidier was made with safe and environmental protection materials, it has been certied and
complied with the requirement of sale regions’ related regulations or laws.
IMPORTANT: Please read and save this SAFETY INSTRUCTIONS before using the device. Basic
precautions should always be followed to reduce the risk of re, electrical shock, and injury to
persons or damage to the product.
01
30 CM
1
1. Please always place the unit on a smooth, at, lint-free, non-metallic, waterproof and level surface and keep it away from direct sunlight.
2. Always place the unit 2 feet (60 cm) above the oor, 12 inches (30 cm) away from the wall, other appliances or wooden furniture.
30 CM
60 CM
2
02
Page 5
WHEN USING THE HUMIDIFIER
AFTER USING THE HUMIDIFIER
1
1. DO NOT plug the unit with wet hands.
2. DO NOT direct the mist nozzle against the wall.
1
1. DO NOT use your hand or any other object to cover the nozzle while the unit is on to avoid damaging the product or causing injury.
2. DO NOT clean the unit while it is connected to a power source or while it is on.
40% 60%
1
Humidity
2
1. Always disconnect from a power source by pulling out the plug when not in use.
2. Humidier requires regular cleaning. Please refer to, and follow the Cleaning and Maintenance instructions.
2
1. DO NOT clean the humidier right after turning it o if the humidier is warm to touch. Allow the humidier to completely cool down before cleaning.
2. DO NOT attempt to repair or adjust any electrical or mechanical functions on this humidier. Doing so will void your warranty.
2
1
1
2
2
1. DO NOT move or tilt the humidier while it is in operation.
2. The most comfortable environmental humidity is between 40%-60%. Please adjust the mist as needed.
03
04
Page 6
PACKAGE CONTENTS
· 1 x Homech Humidier (Model: HM-AH003)
· 1 x Cleaning Brush
· 1 x Dustproof Sponge
· 1 x Thank You Card
· 1 x User Manual
SPECIFICATIONS
Model
Operating Voltage
Rated Power
Water Tank Capacity
Mist Output
Working Time on a Full Tank
Recommended Room Size
Noise
Dimensions
Net Weight
05
HM-AH003
AC 100-120V 50 / 60Hz
Min: 15W
Max: 25W
6.0L / 1.59Gal
Min: 60ml/h
Max: 300ml/h
20-100h
20-40m² / 215-430ft²
27dB (A)
251 x 167 x 412mm / 9.9 x 6.6 x 16.2in
1775g/62.6oz
1
7
8
1. Nozzle
2. Water Tank
3. Water Level Window
4. Tank Cap
5. Water Inlet
6. Handle
7. LED Indicator
8. Control Knob
9. Base
2
3
12
9
10
11
PRODUCT DIAGRAM
10. Light Button
11. Night Light
12. Floater
13. Air Outlet
14. Tank Light
15. Water Reservoir
16. Atomizer
17. Dustproof Sponge
18. Air Inlet
4
5
6
13
14
15
16
push
17
18
06
Page 7
OPERATIONS AND FUNCTIONS
1 2
Add Water
1. Remove the nozzle and turn the water tank upside down.
2. Remove the tank cap and ll the tank with clean and cool water only.
3. Attach the tank cap and place the tank back onto the base. Make sure it ts together securely so that water can go from the tank to the reservoir. Put the nozzle back on.
3 4
OFF
ON
Min
Max
OFF
ON
5
Max
Plug the power cord into a wall socket. Now the humidier is ready for use.
1. Rotate the control knob clockwise to the ON position. The blue LED indicator will light up indicating that the humidier has been turned on .
2. Keep rotating the control knob clockwise to increase the mist level.
3. Rotate the control knob counterclockwise to decrease the mist level.
4. Rotate the control knob counterclockwise to the OFF position to turn o the humidier. The LED indicator will turn o. The fan will work for another 3 minutes to dry the mist tube.
Min
Power On / O and Mist Adjustment
Note:
The most comfortable environmental humidity is between 40%-60%. Please adjust the mist output as needed.
1 2 3 4
1. If tap water is too hard, it is recommended to use ltered or distilled water to avoid white dust. DO NOT use hot water.
2. DO NOT add any essential oils or medicinal tablets into the water tank.
3. DO NOT add water into the base or through nozzle.
4. DO NOT move the humidier while the water tank is full of water to avoid leakage or base overlling.
07
Light Control
1. Press the Light Button to turn on / o the night light.
2. Press and hold the Light Button for 1.5 seconds to turn on / o the tank light.
Low Water Protection: Auto Shut-o the Humidier
When there is not enough water inside the water reservoir, the humidier will stop misting and the LED indicator will become red. It is designed for safety concern to prevent the humidier from possibly overheating and damaging the atomizer.
08
Page 8
CLEANING AND MAINTENANCE
Caution
1. DO NOT submerge the base in water.
2. Make sure water does not enter the base through the air outlet, air inlet,
or the control knob and light button.
3. DO NOT wash any part of this humidier in dish washer which will
damage the humidier and void the warranty.
Daily Maintenance
Turn o the humidier, unplug it from the power source. Drain water from the tank, reservoir and base.
Scale Removal Instructions
15S
1 2
15-20
minutes
Weekly Maintenance
1. To properly clean your humidier, we recommend you to remove scale and disinfect the humidier separately.
2. DO NOT mix vinegar and bleach solutions together. Do not use more than 1 tsp. of bleach per gallon of water to avoid damaging your humidier.
3. Please make sure the rubber ring & rubber cap & spring on the tank cap is installed properly after cleaning to avoid water leakage. Please refer to the diagram on page 13.
09
3
5
4
6
10
Page 9
1. Turn o and unplug the humidier. Remove the nozzle.
2. Remove the water tank from the base. Remove the tank cap. Make sure that the white sealing ring does not come o. Drain water from the water tank and base. Remove any accessories and set them aside.
3. Fill the water tank half full. Add 1 teaspoon of undiluted distilled white vinegar. Attach the tank cap and shake the tank for 15 seconds.
4. Place the tank onto the base. The vinegar solution will enter the water reservoir to loosen mineral buildup (scale) on the atomizer, water oater and the bottom of the water tank. Set it still for 15-20 minutes.
5. Uncap the tank cap and drain the solution. Wipe the atomizer and oater with a soft cloth to remove loosened mineral deposits.
6. Rinse both the water reservoir and water tank until the smell of vinegar (for scale removal) or bleach solution (for disinfecting, see below) is gone.
Clean the Dustproof Sponge
push
Clean the dustproof sponge (at the back of base) with water or detergent once a month. Put it back in place
after cleaning.
push
Disinfecting Instructions
1. Follow steps 1-2 of the previous section on scale removal.
2. Fill the water tank half full. Add ½ tsp of bleach. Place the tank cap back on. Swish the solution around in tank. Place the tank on the base. The bleach solution will enter and disinfect the water reservoir as well as the other components. Set it still for 15-20 minutes.
3. Follow steps 4-6 of the previous section on scale removal to complete disinfecting the humidier.
11
End-Of-Season Care and Storage
1. Follow the cleaning instructions when the humidier will not be used for at least one week,
or at the end of the season. Remove any accessories used with the humidier and allow the
humidier and accessories to dry completely before storing.
2. DO NOT store with water inside the base, water reservoir, or tank.
3. Pack the unit safely and store in a cool, dry location.
12
Page 10
TROUBLESHOOTING GUIDE
1. If the information listed in the troubleshooting guide can’t solve your problem, please email us for help.
2. Failure to keep this unit clean from mineral deposits may aect operation of this unit.
3. Customer failure to follow these instructions may void the warranty.
2
1
3
1. Spring
2. Rubber ring
3. Water oater
The unit is on but no mist or little mist is produced .
Tank leakage.
Not enough water inside the tank.
Mist level is set too low.
The base might be overlled.
Mineral buildup on atomizer.
Tank may be damaged.
Tank cap is not tightened securely.
2
Rubber ring was not installed on tank cap.
Rell and reinstall the water tank.
Adjust to larger mist output.
Remove the tank, empty the base and place back the lled tank on the empty base.
Put your hand towards the nozzle and feel if there is air coming out. If yes, clean the water scale on the atomizer as instructed(p10).
Check for possible cracks in the tank. Ask for a replacement if it is damaged.
Tighten the tank cap.
Check the tank cap for rubber ring, contact us if any is missing .
Problem Possible Cause Solution
Failed to turn on the unit.
Waterless indicator is constantly on.
13
Unit not plugged in.
No power from power outlet.
No water in the water reservoir.
3
Water oater get stuck.
Ensure unit is properly plugged in.
Try another power outlet.
Ensure the spring is secured properly to the tank allowing water to pass through to the base.
Adjust the water oater to a horizontal position and make sure it can rise up with water .
1
3
Mist height is low, damping surrounding desk or oor. Condensation forms around humidier or on windows and walls.
1
Spring get stuck.
Mist level is set too high for the room size.
Air inlet is blocked.
Low indoor temperature leads to liquefaction.
Ensure the spring is secured properly to the tank allowing water to pass through to the base.
1. Check if the room is too humid, adjust to lower mist output.
2. Open door and windows, or change to a larger room.
Humidier should be placed on a hard at surface, 2 feet above the oor, 12 inches away from the wall. Point mist outlet away from wall or window.
Raise the room temperature to 25°C/77°F.
1
14
Page 11
Poor humidication.
Mist level is set too low for the room size.
Air inlet is blocked.
1-1. Adjust to maximum mist output. 1-2. Close door or windows to reduce air ventilation, or change to a smaller room.
Humidier should be placed on a hard at surface, 2 feet above the oor, 12 inches away from the wall.
WARRANTY
This product is covered with Homech product and labor warranty for 12 months from the date of its original
purchase. You will be given a warranty extension of 18 months if the product is registered on our website
(www.homech.net).
Any defective part will be, at the discretion of SUNVALLEYTEK INTERNATIONAL INC. , repaired or replaced at no
charge if the appliance has not been tampered with and has been used according to these printed directions.
White dust appears / Black coating in the base akes o.
Strange odor.
Strange water noise.
Humidier is getting too hot.
Low indoor temperature leads to liquefaction.
Tap water may contain too much minerals.
Unit needs to be cleaned.
Water is going down to the water reservoir.
Unit works long hours.
Raise the room temperature to 25°C/77°F.
Replace with ltered or distilled water or use with a Homech Demineralization Cartridge.
Clean the humidier as instructed.
Leave the empty water tank open in a cool place for 12 hours without the water tank cap attached.
This is normal while it is working.
Power o and place in a well-ventilated place for 10 minutes.
If any problems occur, please contact Homech support (support@homech.net) immediately to launch a warranty claim. Specify model number and your Amazon order number. Our Consumer Service Representative will respond within 1 business day, advise you how to correct the problem yourself, or instruct you on how to return the defective unit back to us for repair or replacement.
We can only provide after sales service for products that are sold by Homech or Homech
authorized retailers and distributors.If you have purchased your unit from a dierent place,
please contact your seller for return and warranty issues.
CONTACT / HOMECH CUSTOMER CARE
PLEASE CONTACT US BEFORE RETURNING THIS PRODUCT TO THE STORE.
EMAIL HOMECH CUSTOMER CARE FOR PROBLEMS AND QUESTIONS.
WE WILL RESPOND WITHIN 1 BUSINESS DAY.
E-mail:
support@homech.net
15 16
Page 12
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
WEEE Compliance
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic
accessories should not be disposed of with other household waste at the end of their working life.
To prevent possible harm to the environment or human health from uncontrolled waste disposal,
please separate these items from other types of waste and recycle them responsibly to promote the
sustainable reuse of material resources. Household users should contact either the retailer where they
purchased this product, or their local government oce, for details of where and how they can take
these items for environmentally safe recycling. Business users should contact their supplier and check
the terms and conditions of the purchase contract. This product and its electronic accessories should
not be mixed with other commercial wastes for disposal.
Loading...