Page 1
D13803.06 Page 1
Installation
Set top bracket*
Unpacking the flat panel screen
Screw kit for table stand and different
types of walls; gypsum/wood, concrete,
brick
Wall mount rail
Wall brackets
With velcro for monitor
fixation, and cable strap.
*If this Flat Panel Display Package has been
purchased together with a TANDBERG Edge
MXP system, there is no need for this set
top bracket. The TANDBERG Edge MXP
package will include a separate bracket for
the PrecisionHD camera.
Wall mount kitTable stand kit
Monitor
Remote Control/
Batteries (AAA x 2)
User Guide CD
Audio Cable
Power Cord
Speaker Set
DVI-D to HDMI cable
Tool needed for the installation:
- Screwdriver PH 2
32" Flat Panel Display Package
?
i
M
SLEEP ARC TEXT
UPDATE
TIME
SIZE MIX
HOLD
REVEAL
INDEX MODE
PSM
LIST
POWERMUTE
TV INPUT I/II
PR
PR
VOL
OK
123
456
789
SSM
0
VOL
Q.VIEWMENU
With cable strap
Page 2
D13803.06 Page 2
Installation
Monitor Configuration
Connecting Cables
Recommended maximum volume on the monitor is 65 out of 100.
Source input: HDMI/DVI
32" Flat Panel Display Package
DVI-D to HDMI Cable
Audio Cable
PC Stereo IN
Bilde nr 6
HDMI
Audio
(RGB/DVI)
AC in
Page 3
D13803.06 Page 3
Wall mount
1. Lay the monitor on a clean surface,
mount the speakers.
Make sure
the velcro
strips are
matched
properly!
3. Bend the bracket into correct shape and
fix onto the monitor.
4. Place Set Top onto bracket.
Overhang of Set Top and bracket is
needed for cable space towards wall.
Maximum 7 cm.
5. Connect cables (see page 2) and
fixate in cable strap.
6. Wall mounting:
Make sure to follow instructions on next page
according to wall type:
A - Wooden pillars (gypsum wall)
60 cm center - center
B - Wooden pillars (gypsum wall)
16 in (41 cm center - center)
C - Brick/concrete wall
Warning!
Due to the size and mass of this equipment, it is very important that
the wall mount unit is safely installed according to the installation
instructions. It is highly recommended that the installation is
provided by persons with appropriate technical training.
32" Flat Panel Display Package
2. Use the inlay
from the monitor
packaging as
temporary stand.
Mount the wall
brackets, using
four screws.
Page 4
D13803.06 Page 4
Wall mount
6 A) Wooden pillars (w/gypsum)
60 cm center-center.
6 B) Wooden pillars (w/gypsum)
16 inch center-center.
6 C) Brick/Concrete wall.
Mount into specified
holes with screws only
Mount into specified
holes with screws only
7 Hook the system onto the wall mount rail.
8 Fixate cables along the wall.
Drill a small
initial hole
Drill a larger
hole for plugs
Mount into
specified
holes with
plugs and
screws
1.
2.
3.
> 1,5 m =
Recommended safety
height to keep Set Top and
other falling parts out of
reach for children.
> 1,5 m
1
2
Ø 3,0 mm
(0,1”)
Ø 8,0 mm
(0,31”)
60 mm
32" Flat Panel Display Package
Page 5
D13803.06 Page 5
Table stand
1. Place monitor onto table stand. 2. Secure the table stand with the six M4x10Secure the table stand with the six M4x10
screws into assigned holes. Make sure to screw
all the way until tight!
3. Mount the speakers with the four
screws attached.
4. Bend the bracket into correct shape and
fix onto the monitor.
32" Flat Panel Display Package
Make sure
the velcro
strips are
matched
properly!
Page 6
D13803.06 Page 6
Table stand
5. Place Set Top onto bracket.
Place bracket and Set Top
along edge of monitor
6. Connect cables (see page 2)
and fixate in cable straps.
7. This is NOT a floor-standing system.
Place the system on a flat and rigid surface or table.
32" Flat Panel Display Package
Loading...