LEFT
STICK
Rudder
Mode1: Elevator
Mode2: Thr ottle
Mode1: Thr ottle
Mode2: Elevator
Aileron
RIGHT
STICK
NORMAL STICK CONFIGURATIONS
™
TTX410, TTX610, TTX810 Radio Mode Changes
These instructions describe how to change the stick mode on Tactic brand
TTX410, TTX610, and TTX810 transmitters. Changing modes requires
mechanical adjustments inside the transmitter and electronic confi guration
changes. Failure to follow these instructions properly can result in permanent
damage to the Tx and void the warranty. Contact Hobby Services if you do not
feel comfortable making such adjustments without damaging the radio.
For safe operation and best results, it’s strongly recommended
to read these instructions completely before use.
These Tactic radios can be changed between stick mode 2 and stick mode 1.
Most radios for use in the United States are produced with stick mode 2
confi guration. The diagram here shows the difference between the two
modes. The locations of the aileron and rudder controls are the same for
radios on mode 2 and mode 1. However, the locations of the throttle and
elevator controls will alternate when changing between mode 2 and mode 1.
Throttle is on the left stick for mode 2, but on the right for mode 1.
ELECTRONIC STICK MODE CHANGE – MODE 2 TO MODE 1
Follow these steps to change the radio’s electronic confi guration from mode 2 to mode 1:
1. With charged batteries inside the Tx, start with the Tx power switch in the
OFF position.
2. Press the up/down trim button on the RIGHT gimbal to the up direction and
HOLD in this position.
3. Turn the Tx power switch to the ON position. The Tx should sound a unique
set of beeps very rapidly (one high and three low tones) to indicate the
throttle control has moved to the right stick and right trim lever, and the
elevator control has moved to the left stick and left trim lever.
4. With the transmitter linked to a Tactic receiver and servos connected to
channels 2 and 3, make sure both the stick and trim controls were swapped
for the throttle and elevator controls.
5. Turn the Tx power switch off, then back on to confi rm the radio held the stick mode change.
6. If the controls for the throttle and elevator channels did not alternate repeat steps 1-4 above.
ELECTRONIC STICK MODE CHANGE – MODE 1 TO MODE 2
Follow these instructions to change the radio’s electronic confi guration from mode 1 to mode 2:
1. With charged batteries inside the Tx, start with the Tx power switch in the
OFF position.
2. Press the up/down trim button on the LEFT gimbal to the up direction and
HOLD in this position.
3. Turn the Tx power switch to the ON position. The Tx should sound a unique
set of beeps very rapidly (one high, and three low tones) to indicate the
throttle control has moved to the left stick and left trim lever, and the elevator
control has moved to the right stick and right trim lever.
4. With the transmitter linked to a Tactic receiver and servos connected to
channels 2 and 3, make sure both the stick and trim controls were swapped
for both the throttle and elevator controls.
5. Turn the Tx power switch off, then back on to confi rm the radio held the stick mode change.
6. If the controls for the throttle and elevator channels did not alternate repeat steps 1-4 above.
1
MECHANICAL STICK MODE CHANGE
WARNING ! Mechanical alterations on the Tactic TTX410, TTX610, and TTX810 radios require opening the
transmitter case. Failure to follow all instructions below can result in permanent damage to the transmitter and
void the warranty. Contact Hobby Services if you do not feel comfortable that you can safely and accurately
perform these steps.
Case Separation and Disassembly
1. Ma ke s ure to fi rst remove all batteries from the battery compartment!
Failure to do so could result in permanent damage to the radio
and void the warranty.
2. Remove the six screws from the back of the Tx case. Put the screws in a safe
place for later use.
3. Carefully separate the case rear away from the case front and note exactly how
all wires are routed inside the case. Taking a picture of the wires in place may
be helpful for re-assembling the case later. Do not disconnect wires from the
pc board.
4. Carefully lay the radio face-down on a soft, non-abrasive surface, with the case
rear opened to expose the inside of the radio.
Throttle Ratchet Bar
1. A long metal bar will be installed vertically across the rear of one gimbal.
This bar provides resistance and a ratchet feel for the throttle control. Note
the small detent in the middle of the bar, and the tip of this detent points
towards the gimbal. Two mounting screws hold the bar into place. One
screw will be inserted fully into the taller mounting post. The other screw
will be partially inserted into the shorter mounting post, to function as a
tension adjustment for the throttle stick. Note the depth at which this screw
is inserted prior to removal. Remove both screws and the ratchet bar from
this gimbal.
2. Position the throttle ratchet bar onto the mounting posts for the opposite
gimbal, making sure the detent in the bar points at the gimbal. Install one
screw fully (don’t over-tighten) into the taller mounting post. Install the
second screw partially in the shorter mounting post, to a depth similar to
when it was removed to provide adequate tension for this stick.
Elevator Arm and Spring Removal
The gimbal now with the metal throttle ratchet bar will still have a plastic arm
and spring for the vertical movement of the stick. The arm and spring must
be removed from this gimbal and moved to the other gimbal.
1. With a pair of hemostats or needle-nose pliers, carefully grasp the loop end
of the spring and slide it off the end of the arm.
2. Lower the spring to slide the opposite loop end off the lever located downward
inside the gimbal assembly. Set the spring aside.
2
Loading...