suprema Secure I/O Installation Manual

Download

Page 1

Secrure door control and I/O expansion

www.supremainc.com

(ver 1.0)

Installation Guide

Page 2

Contents

Product Contents 3 Front Panel Description 4 Rear Panel Description 5 Connectors for External Interfaces 6 Installation Example 8 Product Dimension 9 Power Connection 10 RS-485 Connection 11 Relay Connection 12 RTE Switch Connection 14 Fire Alarm Connection 15 System Specifications 16

Page 3

Product Contents

 Basic Contents

Product Contents

Secure I/O

Wall mounting screws

120 Ohm Resistor & Diode

Page 4

Front Panel Description

RLY0 LED - Status of Relay0 RLY1 LED - Status of Relay1 RX LED - Status of RS-485 Rx signal TX LED - Staus of RS-485 Tx signal IN0 LED - Status of Input0 IN1 LED - Status of Input1 IN2 LED - Status of Input2 IN3 LED - Status of Input3 PWR LED - Power status RUN LED - Status of Secure I/O oper atio n

RESET BUTTON - Secure I/O hardware reset SYNC BUTTON - Syncronization between Secure I/O and dev

ice (BioStation/ BioEntry Plus) f or security by exchanging an e ncryted keys. This prevents the operation of Secure I/O when the external device has been exchanged by an intruder. Sync button should be pressed when a device is set as a host in a RS-485 loop.

Page 5

Rear Panel Description

ID = 0 ID = 1

ID = 2 ID = 3

ID0 / ID1 - Dip switch to set an ID of Secure I/O Since max number of Secure I/O in an RS-485 loop is four,

the ID of Secure I/O should be set among 0, 1, 2, 3.

RSV - reserved for future use

Secure I/O ID setting

Page 6

Connectors for External Interfaces 1

Relay Output0 Normal Open Relay Output0 Common Relay Output0 Normal Close Relay Output1 Normal Open Relay Output1 Common Relay Output1 Normal Close RS-485 TRX+ RS-485 TRXRS-485 Ground Frame Ground Power Input+ Power Input -

IN0

IN1

IN2

IN3

IN0

RESET

SYNC

RLY0

RLY1

N.O 0

COM 0

N.C 0

N.O 1

COM 1

N.C 1

TRX+

TRX-

TRXGND

PWR+

PWR-

IN 0+

IN 0-

IN 1+

IN 1-

IN 2+

IN 2-

IN 3+

IN 3-

FGND

Page 7

Connectors for External Interfaces 2

IN0

IN1

IN2

IN3

IN0

RESET

SYNC

RLY0

RLY1

N.O 0

COM 0

N.C 0

N.O 1

COM 1

N.C 1

TRX+

TRX-

TRXGND

PWR+

PWR-

IN 0+

IN 0-

IN 1+

IN 1-

IN 2+

IN 2-

IN 3+

IN 3-

FGND

External Input 0 + External Input 0 External Input 1 + External Input 1 External Input 2 + External Input 2 External Input 3 + External Input 3 --

Page 8

Installation Example

Exit Button

Door Lock

RS-485

Relay Output

External Input

BioStation or

BioEntry Plus

Secure I/O

Page 9

Product Dimension

Top

Side

(unit : mm)

Page 10

Power Connection

Recommended power supply

z 12V ± 10%, at least 500mA for Secure IO alone installation. z Comply with standard IEC/EN 60950-1 z To share the power with other devices, use a power supply with hi gher current ratings.

DC 12V Power Source

DC 12V Positive

DC 12V Negative

Earth Ground

Page 11

RS-485 Connection

N.O 0 COM 0 N.C 0 N.O 1 COM 1 N.C 1 TRX+ TRXTRXGND

PWR+ PWR-

BioStation or BioEntry Plus

RS-485 TRX+

RS-485 TRXRS-485 Ground

120 Ohm

resistor

z In case the length of RS-485 line is so long to affect communication stability, connect the

enclosed 120 Ohm resistor between TRX+ and TRX- connector of Secure I/O

Page 12

Relay Connection – Fail Secure Lock

Dead Bolt / Door Strike

DC Power

Source

z When using dead bolt or door strike, connect an enclosed diode as in the above diagram.

Anode (line mark) of the diode should be connected to + power (Be careful of the direction)

Page 13

Relay Connection – Fail Safe Lock

Deal Bolt /

Door Strike

DC Power

Source

z When using dead bolt or door strike, connect an enclosed diode as in the above diagram.

Anode (line mark) of the diode should be connected to + power (Be careful of the direction)

Page 14

RTE Switch Connection

RTE Switch or

Exit Button

Page 15

Fire Alarm Connection

Alarm Output+ Alarm Output-

Fire Alarm System

Page 16

System Specifications

 CPU : 8bit, 16MHz Microcontroller  Memory : 32Kbyte Flash  Display : 10ea Status LED  IO : Input X 4Ch, Output X 2Ch, RS-485 X 1Ch  Product size : 142.5 x 110 x 39 mm (width x length x depth)

Min. Typ. Max. Notes

Power

Voltage (V) 10.8 12 13.2

Current (mA) - 500 800 Relay

Normal switching capacity(N.O) (Resistive)

5A 2A 3A

125VAC 250VAC 30VDC

Normal switching capacity(N.C) (Resistive)

2A 1A 1A

125VAC 250VAC 30VDC

Page 17

Suprema Inc.

16F Parkview Office Tower, Jeongja-dong, Bundang-gu,

Seongnam, Gyeonggi, 463-863 Korea

E-mail : support@supremainc.com

Website : www.supremainc.com

Functions and specifications of the product are subject to changes without notice due to quality enhancement or function update. For any inquiry on the product, please contact Suprema Inc.