Page 1
www.suprema.co.kr
Face-Station
Innovative Fingerprint Terminal
Installation Guide
(ver0.1)
Page 2
Product Contents
n Basic Contents
Product Contents
Terminal Wall mounting metal bracket
Cables
Screw for fixing main body
Wallmounting
screwsand holders-4 ea
Ferrite Core
Software CD
ⒸCopyright 2010Suprema Inc.
2
Page 3
Product Contents
USB fingerprint scanner f
n Optional accessories
or enrollmenton PC
Wireless LAN Access Point
3
ⒸCopyright 2010Suprema Inc.
Page 4
Cable and Connector Pinout
Relay
PIN PIN DESCRIPTION
1 NORMAL OPEN
2 COMMON
3 NORMAL CLOSE
Before Start
RS485
PIN PIN DESCRIPTION
1 TRX 2 TRX +
3 GND
4 SHIELD GND
4
ⒸCopyright 2010Suprema Inc.
Page 5
Cable and Connector Pinout
2
GND
Switch Input
VDP
PIN PIN DESCRIPTION
1 SWIN_IN0
2 SWIN_IN1
3 GND
4 SHIELD_GND
5 SWIN_IN2
6 SWIN_IN3
7 GND
8 SHIELD_GND
PIN PIN DESCRIPTION
1 VDP_S
3 VDP_VCC
4 VDP_V
5 VDP_OPEN
6 GND
7 SHIELD_GND
Before Start
Wiegand
PIN PIN DESCRIPTION
1 WIEGAND_D0
2 WIEGAND_D1
3 GND
4 SHIELD GND
5
ⒸCopyright 2010Suprema Inc.
Page 6
Installation Example
8P Cable
PC
Network HUB
Firmware
Upgrade Only
Ethernet
3P Cable
Door Lock
Exit Button
USBUSB
6
ⒸCopyright 2010Suprema Inc.
Page 7
Product Dimension
132
165
Front
(unit : mm)
7
ⒸCopyright 2010Suprema Inc.
Page 8
Ferrite Core 사용법
ⒸCopyright 2010Suprema Inc.
8
Page 9
전원연결
n Power Connection
n Recommended
l12V ± 10%, at least 1500mA for BioStation T2 alone installation.
lComply with standard IEC/EN 60950-1
9
ⒸCopyright 2010Suprema Inc.
Page 10
LAN Connection
ⒸCopyright 2010Suprema Inc.
10
Page 11
RS485 Network Connection
Before Start
11
ⒸCopyright 2010Suprema Inc.
Page 12
Relay Connection – Fail Safe Lock
ⒸCopyright 2010Suprema Inc.
12
Page 13
Relay Connection – Fail Secure Lock
ⒸCopyright 2010Suprema Inc.
13
Page 14
Relay Connection -Automatic Door
ⒸCopyright 2010Suprema Inc.
14
Page 15
TTL Input Port Connection – RTE Switches
(8)
SHELD
_
GND
Request
To Exit #1
Cable shield(optional)
DStation
Request
To Exit #1
Request
To Exit #1
Request
To Exit #1
(7) GND
(6) TTL_IN3
(5) TTL IN2
(2) SHELD_GND
(3) GND
(2) TTL IN1
(1) TTL IN0
15
ⒸCopyright 2010Suprema Inc.
Page 16
Wiegand Input Connection – External reader
ⒸCopyright 2010Suprema Inc.
16
Page 17
System Specifications
n
RS-232(Share with RS
-
485) X 1ch
n ● CPU :Main B/D CPU -ARM11 667MHz X 1ea
n -DSP 1GHz X 1ea
n
n ● Memory : Main B/D -Flash : Nand SLC 512MByte, SDRAM(mDDR) : 256MByte
n
n ● DISPLAY : 4.3inch LCD X 1ea
n ● INPUT : 저항막방식 Touch Screen X 1ea + 5 Keypad (F1~F4, CALL)
n ● CAMERA : VGA CMOS Camera X 2ea
n ● I/O Port : Wiegand In/Out (S/W 설정을통해 Input 또는 Output으로사용가능) X 1ch
n Switch Input X 4ch
n RS-485 X 2ch
n Relay(1A@30Vdc) X 2ch
n Ethernet(10/100M) X 1ch
n ● Sound Out: System Sound용 Speaker X 2ea
n ● RF CARD : Mifare
n ● Power Input : 12Vdc Adaptor or POE Input
기타
17
ⒸCopyright 2010Suprema Inc.
Page 18
FCC Rules
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
Caution
Warning
Information to User
Changes or modifications not expressly approved by the manufacturer
responsible for compliance could void the user’s authority to operate the
equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interface, and
(2) this device must accept any interface received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limit of a Class B
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, user and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation; if this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more the
following measures:
1. Reorient / Relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit difference from that to
which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help
18
ⒸCopyright 2010Suprema Inc.
Page 19
Electrical Specification
Min. Typ. Max. Notes
Power
Voltage (V) 10.8 12 13.2
Current (mA) - 700
TTL/Wiegand Input
VIH(V) 2 - VIL(V) - - 0.8
Pull-up resistance (Ω) - 10k TTL/Wiegand Output
VOH(V) 4 - - @ IOH= -5mA
VOL(V) - - 1 @ IOL= 5mA
Output resistance (Ω) - 100 Relay
Switching capacity (A) - -
Switching power
(resistive)
Switching voltage (V) - -
- -
1
0.3
30W
37.5VADCAC
110
125
30V DC
125V AC
DC
AC
19
ⒸCopyright 2010Suprema Inc.
Page 20
Suprema Inc.
16F Parkview Office Tower, Jeongja-dong, Bundang-gu,
Seongnam, Gyeonggi, 463-863 Korea
E-mail : support@supremainc.com
Website : www.supremainc.com
Functions and specifications of the product are subject to changes without notice due to quality
enhancement or function update. For any inquiry on the product, please contact Suprema Inc.
Loading...