R
ELECTRIC PRESSURE WASHER
OPERATOR’S MANUAL
A Division of Snow Joe®, LLC Model SPX4003 Form No. SJ-SPX4003-880E-M
2200 PSI MAX* | 1.6 GPM MAX | 14.5-AMP
IMPORTANT!
Safety Instructions
All Operators Must Read These
Instructions Before Use
mWARNING! This indicates a hazardous situation, which,
if not avoided, could result in death or serious injury.
mCAUTION! This indicates a hazardous situation, which,
if not avoided, could result in minor or moderate injury.
mDANGER! This indicates a hazardous situation, which,
if not followed, will result in death or serious injury.
General Safety
mWARNING! This appliance is not intended for use
by children or by unassisted, unsupervised persons whose
physical, sensory or mental capabilities prevent them from
using it safely. Children should be supervised to ensure that
they do not play with the appliance.
Before starting up your machine, please check it carefully for
any defects. If you nd any, do not start up your machine.
Contact your authorized Snow Joe
call the Snow Joe
1-866-SNOWJOE (1-866-766-9563).
®
+ Sun Joe® customer service center at
®
+ Sun Joe® dealer or
mWARNING! When using the pressure washer, basic
safety precautions should always be followed to reduce the
risk of re, electric shock, and personal injury. These include:
• Know your product – Know how to stop the machine and
bleed pressure quickly. Thoroughly familiarize yourself with
the controls.
• Keep bystanders away – All visitors and pets should be
kept a safe distance away from the work area.
• Use the right product – Do not use this machine for any
job except that for which it is intended.
• Dress properly – Do not wear loose clothing or jewelry.
They can get caught in moving parts. Protective rubber
gloves and non-slip footwear are recommended when
working outdoors.
•
mCAUTION! – Exercise caution to avoid slipping or falling.
Wear protective footwear that will protect your feet and
improve your footing on slippery surfaces.
• Stay alert – Watch what you are doing. Use common
sense. Do not operate the pressure washer when you are
tired, or under the inuence of alcohol or drugs.
• Do not overreach –
all times.
• Avoid unintentional starting – Do not carry a plugged-
in machine with your nger on the trigger. Make sure the
switch is o before plugging in the machine.
• Do not abuse the cord – Never carry the machine by the
cord or yank the cord to disconnect it from the receptacle.
Keep the cord away from heat, oil, and sharp edges.
• Use safety glasses – Also use safety footwear, snug-tting
clothing, protective gloves, hearing and head protection.
• Check the water temperature – This pressure washer is
not meant to pump hot water. NEVER connect it to a hot
water supply as it will signicantly reduce the life of the
pump.
• Store indoors – NEVER store the pressure washer
outdoors or where it could freeze. The pump could be
seriously damaged.
• Ground Fault Circuit Interrupter (GFCI) – This product
is provided with a ground fault circuit interrupter built into
the power cord plug. If replacement of the plug or cord is
needed, use only identical replacement parts.
• Inspect electrical cords – The insulation of the power cord
should be perfectly intact. If the power cord is damaged or
shows any signs of wear or tear, do not use the pressure
washer. Contact your authorized Snow Joe
dealer or call the Snow Joe
center at 1-866-SNOWJOE (1-866-766-9563).
Keep proper footing and balance at
®
®
+ Sun Joe® customer service
+ Sun Joe®
mWARNING! Do not use this appliance without reading
this instruction manual.
mWARNING! This appliance has been designed for
use with cleaning agents that are recommended by the
manufacturer. The use of other cleaning agents or chemicals
may adversely aect the safety of the appliance.
mWARNING! Do not use the appliance within range of
persons unless they are wearing protective clothing.
mWARNING! High-pressure jets can be dangerous if
subject to misuse. The jet must not be directed at persons,
pets, live electrical equipment, or the appliance itself.
• Do not direct the jet at yourself or others in order to clean
clothes or footwear.
© 2018 by Snow Joe®, LLC
All rights reserved. Original instructions.
SAVE THESE INSTRUCTIONS
1
• Risk of explosion – Do not spray ammable liquids.
• Disconnect the tool – Disconnect from the electrical power
supply before performing any maintenance task.
• Keep children away – This high-pressure electric
power washer must not be used by children or untrained
personnel.
• To ensure appliance safety, use only original replacement
parts from the manufacturer or those approved by the
manufacturer.
mWARNING! Water that has owed through backow
preventers is considered to be non-potable.
mWARNING! During cleaning, maintenance or when
replacing parts, the machine must be disconnected from its
power source by removing the plug from the socket outlet.
mWARNING! High-pressure hoses, ttings, and
couplings are important for the safe operation of the appliance.
Use only hoses, ttings, and couplings recommended by the
manufacturer.
• Check for damaged parts – Do not use the appliance if
the supply cord or other important parts of the appliance
are damaged (e.g. safety devices, high-pressure hoses,
trigger gun).
mWARNING! If an extension cord is used, the plug and
socket must be of watertight construction.
mWARNING! Inadequate extension cords can be
dangerous.
• This high-pressure electric power washer must not be used
at temperatures below 32ºF (0°C).
mWARNING! Power cords on drums should always be
completely unwound to prevent the cord from overheating.
• Power cord connections should be kept dry and o the ground.
• If the power cord is damaged, do not use the appliance.
Contact your authorized Snow Joe
call the Snow Joe
1-866-SNOWJOE (1-866-766-9563).
• Keep the machine on a stable, at surface during operation,
handling, transportation, and storage. Sudden overturn of
the machine can cause bodily injury.
• In the event of an accident or breakdown, switch o the
machine immediately. (If contact with detergent occurs,
rinse with an abundance of clean water).
®
+ Sun Joe® customer service center at
®
+ Sun Joe® dealer or
Electrical Safety
ATTENTION: If there are problems with the electrical
MAINS, short voltage drops may appear when starting the
equipment. This can, in turn, inuence other equipment
(e.g. cause a lamp to blink). If the MAINS-IMPEDANCE Zmax
< 0.335 OHM, such disturbances are not expected. (If you
require assistance, contact your local supply authority for
further information.)
mWARNING! Electrical Shock Hazard – Before starting
up your machine, please check it carefully for any defects. If
you nd any, do not start up your machine and contact your
distributor.
The following should be observed when connecting the
high-pressure electric power washer to the electric supply:
• The electric supply connection should be performed by a
qualied person.
• The electric supply to this appliance should include either
a residual current device that will interrupt the supply if the
leakage current to the earth exceeds 30 mA for 30 ms or a
device that will interrupt the earth circuit (GFCI).
IMPORTANT: Only use water without any impurities.
If there is a risk of running sand into the inlet water (i.e. from
your own well), an additional lter should be installed.
Safety Devices
The unloader valve can reduce pressure if it exceeds preset
values. The spray gun features a locking device. When the lock
is activated, the spray gun cannot be operated.
1. Thermal sensor – A thermal sensor protects the motor
against overloading. The machine will restart after a few
minutes when the thermal sensor has cooled.
2. Double insulation – In a double-insulated appliance, two
systems of insulation are provided instead of grounding.
No grounding means is provided on a double-insulated
appliance, nor should a means for grounding be added
to the appliance. Servicing a double-insulated appliance
requires extreme care and knowledge of the system, and
should be performed only by qualied service personnel at
an authorized Snow Joe
parts for a double-insulated appliance must be identical
to the parts they replace. A double-insulated appliance
is marked with the words “Double Insulation” or “Double
Insulated.” The symbol
also be marked on the appliance.
3. Ground fault circuit interrupter (GFCI) protection – This
pressure washer is provided with a ground-fault circuitinterrupter (GFCI) built into the plug of the power-supply
cord. This device provides additional protection from the
risk of electric shock. Should replacement of the plug or
cord become necessary, use only identical replacement
parts that include GFCI protection.
4. It is not recommended to use an extension cord with
this pressure washer. The unit comes standard with a
35 ft GFCI power cord. Using an extension cord may
cause a drop in line voltage resulting in loss of power and
overheating.
5. To reduce the risk of electric shock, this appliance has
a polarized plug (i.e. one blade is wider than the other).
The appliance plug will t into a polarized outlet only one
way.
®
+ Sun Joe® dealer. Replacement
(square within a square) may
2
If the appliance plug does not t fully into the outlet,
reverse the plug. If the plug still does not t, make sure
that you are using the correct polarized wall outlet. If the
plug still does not t, contact a qualied electrician to install
the proper wall outlet. Do not modify the appliance plug,
power cord receptacle, or power cord plug in any way.
If an extension cord is going to be used. Use only 3-wire
extension cord that has 3-prong grounding type plug for
the product. Use only extension cords that are intended
for outdoor use. These extension cords are identied by
marking "Acceptable for use with outdoor appliance; store
indoors while not in use". Use only extension cord having
an electrical rating not less than the rating of the product.
Do not use damaged extension cords. Examine extension
cord before using and replace if damaged. Do not abuse
extension cord and do not yank on any cord to disconnect.
Keep cord away from heat and sharp edges. Always
disconnect extension cord from the receptacle before
disconnecting the product from the extension cord.
m WARNING m
Electric shock may cause SEVERE INJURY or
DEATH. Heed these warnings:
• Do not allow any part of the electric pressure washer
to make contact with water while it is in operation. If
the appliance becomes wet while turned o, wipe dry
before starting.
• Do not use an extension cord over 25 ft. The
pressure washer comes equipped with a 35 ft power
cord. Combined cord length must not exceed 60 ft.
Any extension cord must be 14-gauge (or heavier) to
safely power the pressure washer.
• Do not touch the appliance or its plug with wet hands
or while standing in water. Wearing rubber boots
oers some protection.
EXTENSION CORD CHART
Cord Length:
Min. Wire Gauge (A.W.G.):
6. To prevent the appliance cord from disconnecting from the
extension cord during operation, make a knot with the two
cords as shown in Table 1.
25 ft (7.6 m)
14
Table 1. Method of Securing Extension Cord
Cord set Appliance cord
(A) Tie cord as shown
(B) Connect plug and receptacle
7. Do not abuse the cord. Never pull the pressure washer
by the cord or yank the cord to disconnect it from the
receptacle. Keep the cord away from heat, oil, and
sharp edges.
Risk of Electrocution
• Inspect cord before using.
• Do not use if cord is damaged.
• Keep all connections dry and o the ground.
• Do not touch plug with wet hands.
• Keep cord away from heat and sharp edges.
• Do not spray electrical apparatus and wiring.
Risk of Explosion
• Do not spray ammable liquids.
• Do not use acids, bases, solvents, or any ammable
material in this product. These substances can cause
physical injuries to the operator and irreversible damage to
the machine.
Additional Safety Instructions
• High-pressure: keep clear of nozzle.
• Injection hazard: equipment can cause serious injury if the
spray penetrates the skin.
• Do not point the gun at anyone or at any part of the body.
• In case of skin penetration, seek medical aid immediately.
• Before servicing, cleaning, or removing any parts, shut o
the power and relieve pressure.
• This machine is not suitable for connection to the potable
water mains.
3
Product Description
Purpose
• This high-pressure electric power washer is intended for
residential use to clean vehicles, machines, buildings,
facades, etc.
Areas of Application
• Never use the machine in potentially explosive areas under
any circumstances!
• The operating temperature must be between 32ºF (0ºC) and
104ºF (40ºC).
• The machine consists of an assembly with a pump, which
is encased in a shock-absorbing housing. To provide the
operator with an optimal working position, the machine is
equipped with a spray wand and a non-slip handle grip,
whose shape and conguration comply with applicable
regulations.
• Do not cover or modify the spray wand or the spray nozzle
in any way.
• The high-pressure electric power washer is designed to be
used with cold or lukewarm water; higher temperatures can
damage the pump.
• Do not use water that is dirty, gritty, or contains any
chemical products, as these could impair operation and
shorten the life of the machine.
4
Safety Symbols
The following table depicts and describes safety symbols that may appear on this product. Read, understand, and follow all
instructions on the machine before attempting to assemble and operate.
Symbols SymbolsDescriptions Descriptions
READ THE OPERATOR'S
MANUAL(S) – Read, understand,
and follow all instructions in the
user manual(s) before attempting
to assemble and operate.
WARNING! Electrical shock hazard –
Do not touch the plug with wet hands.
SAFETY ALERT – Indicates a
precaution, a warning, or a danger.
WEAR EYE AND HEARING
PROTECTION – For protection
against injury, wear ear defenders
and safety goggles.
Wear safety gloves during
use to protect hands.
Store indoors. Never store the
pressure washer outdoors.
If the pump freezes, permanent
damage may result.
WARNING! Do not expose the unit
to rain or wet conditions. Keep dry.
To reduce the risk of injury, user
must keep all bystanders at least
49 ft (15 m) away.
Wear non-slip footwear that will
protect your feet and improve your
footing on slippery surfaces.
Machine not suitable for connection
to the potable water mains.
Always keep the power cord
away from heat sources, oils, or
sharp edges. Immediately remove
plug from the mains if the cord is
damaged, frayed, or entangled.
Sound power level is 96 dB(A).
WARNING! Turn the machine OFF
and disconnect it from the power
supply before inspecting, cleaning,
changing accessories, or conducting
any other maintenance task.
Double Insulation – When servicing,
use only identical replacement parts.
5
Know Your Electric Pressure Washer
Read the owner’s manual and safety instructions carefully before operating the electric pressure washer. Compare the illustration
below to the electric pressure washer in order to familiarize yourself with the location of the various controls and adjustments.
Save this manual for future reference.
1. Soft grip
2. Trigger gun
3. Safety lock
4. Trigger
5. High-pressure hose connection
6. High-pressure hose
7. Trigger gun holder
8. Cord holder (2)
9. Power cord with GFCI
10. Spray wand
11. Water outlet (high-pressure hose connection)
12. Adjustable nozzle
13. Wheel (2)
14. Detergent tank screw (2)
15. Detergent tank
16. Detergent tank cap
17. Water inlet + Garden hose adapter
(female coupler)
18. ON/OFF dial
(pressure select technology)
19. Detergent dial
20. Lower handle frame
21. High-pressure hose holder
22. Upper handle frame
23. Needle clean-out tool
11
BACK
1
2
3
4
5
6
7
8
9
10
12
13
14 15 16
23
22
21
20
19
18
17
Technical Data
Rated Voltage ...........................................120 V ~ 60 Hz
Motor ........................................................14.5 amp (1800 W)
Max Water Inlet Temperature ...................104ºF/40ºC
Max Water Inlet Pressure .........................0.7 MPa
Max Flow ..................................................1.6 GPM
Max Pressure* .............................................2200 PSI (15 MPa)
*Peak pressure at initial discharge; working pressure under typical load is 1130 PSI (low setting) and 1650 PSI (high setting).
Rated Pressure ...........................................Low 1130 PSI
High 1650 PSI
Detergent Tank Capacity ............................54.1 oz (1.6 l)
Adjustable nozzle .......................................0º to 45º
High-Pressure Hose Length ........................20 ft (6 m)
Power Cord Length ....................................35 ft (10.7 m)
Weight ........................................................27.3 lbs (12.4 kg)
6
Unpacking
Assembly
Carton Contents
• Upper handle frame
• Lower handle + pressure washer assembly
• Trigger gun
• Adjustable spray wand
• Trigger gun holder
• High-pressure hose
• High-pressure hose holder
• Screw (x4)
• Trigger gun holder
• Nut + bolt
• Garden hose adapter (female coupler)
• Needle clean-out tool
• Manuals with registration card
1. Carefully remove the pressure washer and check to see
that all of the above items are supplied.
2. Inspect the product carefully to make sure no breakage or
damage occurred during shipping. If you nd damaged or
missing parts, DO NOT return the unit to the store. Please
call the Snow Joe
1-866-SNOWJOE (1-866-766-9563).
NOTE: Do not discard the shipping carton and packaging
material until you are ready to use your new electric
pressure washer. The packaging is made of recyclable
materials. Properly dispose of these materials in
accordance with local regulations.
IMPORTANT! The equipment and packaging material are
not toys. Do not let children play with plastic bags, foils,
or small parts. These items can be swallowed and pose a
suocation risk!
®
+ Sun Joe® customer service center at
mWARNING! Do not connect to power supply until
assembly is complete. Failure to comply could result in
accidental starting and possible serious personal injury.
1. Position the washer as CLOSE as possible to the
water supply.
2. The washer must be used on a secure and stable surface
in a standing, upright position (Fig. 1).
Fig. 1
3. Connect high pressure hose holder to upper handle frame
using 4 screws provided, as shown (Fig. 2).
Fig. 2
Upper
handle
frame
High pressure
hose holder
Screws
4. Connect trigger gun holder to upper handle frame using
supplied nut and bolt, as shown. Tighten securely (Fig. 3).
Fig. 3
Upper handle frame
Trigger gun holder
7
Bolt
Nut
5 Slide the upper handle frame into lower handle then
depress the small buttons at the end of the upper handle
frame, push and insert into lower handle until it snaps
securely into place (Figs. 4 – 5).
Fig. 4
6. Connect the high-pressure hose to the water outlet on the
washer (Fig. 6).
Fig. 6
(REAR)
Fig. 5
Push button
Upper
handle
frame
Lower
handle
Upper
handle
frame
High-pressure
water outlet
7. Fit the spray wand into the gun and rotate it until the two
parts are completely locked (Fig. 7).
Fig. 7
8. Connect the high-pressure hose to the trigger gun (Fig. 8).
High-pressure hose
Lower
handle
Fig. 8
Trigger gun
High-pressure hose
8
mWARNING! Keep hose away from sharp objects.
Bursting hoses may cause injury. Examine hoses regularly and
replace if damaged. Do not attempt to mend a damaged hose.
9. Connect the garden hose adapter (female coupler)
to the water inlet of the pressure washer, then thread
your garden hose (male end) into the garden hose
adapter (Figs. 9 – 10). The garden hose must have an
internal diameter of at least 13 mm (1/2 in.) and must be
reinforced. The water supply must be at least equal to the
washer delivery capacity.
NOTE: The machine is not suitable for connection to the
potable water main.
10. Attach garden hose to water supply (Fig. 11).
Fig. 11
Connect to water supply
Garden hose
Fig. 9
Water inlet
(female coupler)
Garden hose adapter
(female coupler)
Garden hose
(male end)
Fig. 10
This end to the
water inlet on
the unit
Garden hose adapter
(female coupler)
(FRONT)
(FRONT)
mWARNING! Do not connect to potable water system.
mWARNING! If connection is made to a potable water
system, the system shall be protected against backow.
mWARNING! The intake water temperature must not
exceed 104ºF/40ºC. The water supply must not exceed
0.7 MPa.
mCAUTION! The washer must only be used with clean
water; use of unltered water containing corrosive chemicals
will damage the washer.
11. Make sure the ON/OFF switch (pressure select dial) is set
in the STOP (0) position before plugging the unit into the
power outlet (Fig. 12).
Fig. 12
LOW
STOP
0
HIGH
Garden hose
9
12. Check that the electrical supply voltage and frequency
(Volt/Hz) correspond to those specied on the pressure
washer rating plate. If the power supply is correct, you
may now plug the pressure washer into the power outlet
(Fig. 13).
Fig. 13
Reset
RESET
GFCI
TEST
Power light
indicator
NOTE: The GFCI may need to be reset when rst plugged
into the electric outlet. Press the "Reset" button until the
power light indicator on the GFCI illuminates.
Fig. 15
3. Turn the ON/OFF switch (pressure select dial) to the LOW (I)
or HIGH (II) position to start the pressure washer (Fig. 16).
Fig. 16
STOP
0
HIGH
LOW
Operation
mIMPORTANT! This pressure washer is equipped with
a micro-switch sensitive to water ow. This Total Stop System
(TSS) senses water ow in the pump. When the trigger is
released, water stops owing through the pump. The TSS then
automatically turns the motor o to protect the pump from
overheating, thus saving energy and prolonging pump life.
1. Turn the water supply tap on completely.
2. Release the safety lock, then press the trigger for a few
seconds until the water ow is steady. Operating the
pressure washer in this manner will allow air to escape and
discharge residual pressure in the hose (Figs. 14 and 15).
Fig. 14
Safety lock
Using the adjustable spray nozzle
mWARNING! High-pressure jets can be dangerous if
subject to misuse. The jet must not be directed at persons,
pets, live electrical equipment, or the appliance itself.
1. The spray wand is equipped with an adjustable nozzle.
2. The water pressure can be adjusted to low pressure (–)
and high pressure (+) by turning the pressure adjustment
knob. The nozzle tip can be adjusted from pencil spray
(wide open tip) to fan spray (narrow tip) by turning the
nozzle tip adjustment knob (Fig. 17).
NOTE: When using the unit with detergent, the spray
nozzle has to be set into low pressure and fan spray. The
pressure settings on the spray nozzle are only meant to
work with detergent, it will not aect the overall working
pressure of the unit.
Trigger
10
Pencil spray
Nozzle tip
Pressure adjustment knob
Fig. 18
Nozzle tip
adjustment knob
Fig. 17
Fan spray
mWARNING! Do not adjust the nozzle while the trigger
is squeezed. Failure to do so could result in damage.
Working with Detergents
When cleaning with the pressure washer, some cleaning tasks
can be solved with water alone, but for most tasks cleaning
with detergent allows for more eective dirt removal.
mWARNING! To apply detergents, you must use the low
pressure setting and the fan spray setting on the spray nozzle.
This setting will gently apply the detergent at a pressure
equivalent to a low-set garden hose. The high-pressure setting
on the spray nozzle is used for rinsing. You cannot apply
detergents when working at high pressure setting on the spray
nozzle.
The pressure settings on the unit will not aect the using of
detergent.
mWARNING! Use only detergents specically designed
for use with pressure washers, such as Sun Joe
DECK WASH (SPX-HDC1G), Sun Joe
WASH (SPX-FCS1G), or Sun Joe
(SPX-APC1G). DO NOT USE household detergents, acids,
alkaline solutions, bleaches, solvents, ammable material, or
industrial grade solutions. These could damage the pressure
washer. Many detergents may require mixing prior to use.
Prepare the cleaning solution as instructed on the solution
bottle.
1. Set the adjustable nozzle to the low-pressure, fan-spray
setting (Fig. 18).
®
SNOW FOAM AUTO
®
HEAVY DUTY CLEANER
®
HOUSE +
Open to apply detergents
2. Remove the cap from the detergent tank and ll the tank
with detergent (Fig. 19).
Fig. 19
Pressure washer
detergent
3. Turn on the pressure washer. Pull the trigger to operate
the unit. The liquid detergent will automatically mix with
water and be discharged through the nozzle.
Detergent
tank
mCAUTION! Always test the detergent in an
inconspicuous area before use.
4. Turn the detergent dial to adjust the suction volume of the
detergent solution (Fig. 20).
Fig. 20
MIN
11
Detergent dial
MAX
5. Apply detergent from the bottom to the top of the dry
surface to be cleaned.
NOTE: Wetting the surface rst is not recommended as it
dilutes the detergent and reduces its cleaning ability.
6. Allow the detergent to remain on the surface for a short
time before rinsing. Do not allow the detergent to dry on
the surface.
mCAUTION! Damage may occur to painted surfaces if
the detergent is allowed to dry on the surface. Wash and rinse
a small section at a time. Avoid working on hot surfaces or in
direct sunlight.
7. When nished using the pressure washer, you must rst
drain and rinse the detergent tank. Run the pressure
washer in low pressure until all of the soap is drained from
the detergent tank.
mCAUTION! Failure to follow these cleaning instructions
will cause the injection system to become clogged and
inoperable.
mIMPORTANT! NEVER USE:
• Bleach, chlorine products, and other corrosive chemicals
• Liquids containing solvents (e.g. paint thinners, gasoline, oils)
• Tri-sodium phosphate products
• Ammonia products
• Acid-based products
These chemicals will harm the unit and will damage the
cleaning surface.
Shutting Down
1. Turn the switch to the STOP (0) position and unplug the
power cord from the outlet.
2. Turn o the water source.
3. Hold the trigger to release water pressure.
4. Disconnect the garden hose from the water inlet on
the unit.
5. Disconnect the high-pressure hose connection on the
trigger gun handle.
6. Release the trigger and engage the gun safety lock.
mWARNING! Turn o the water supply and squeeze the
trigger to depressurize the unit. Failure to do so could result in
personal injury due to discharge of high-pressure water.
Taking a Break
If you are taking a break of ve minutes or more between
cleaning tasks:
1. Engage the gun safety lock (Fig. 14).
2. Turn the switch to the STOP (0) position.
3. Unplug the power cord from the outlet.
Storage
m
CAUTION! Always store your pressure washer in a
location where the temperature will not fall below 32ºF (0ºC).
The pump in this machine is susceptible to permanent damage
if it freezes. FREEZE DAMAGE IS NOT COVERED BY THE
WARRANTY.
• Store the pressure washer indoors in a dry, covered area
where it is not subject to adverse weather conditions.
• It is important to store this product in a frost-free area.
• Always empty water from all hoses, the pump, and the
detergent bottle(s) before storing.
mCAUTION! The use of a pump protector is
recommended to prevent cold weather damage during storage
over the winter months.
Winterizing + Long-Term Storage
If you must store your pressure washer in a location where the
temperature falls below 32ºF (0ºC), you can minimize the chance
of damage to your machine by utilizing the following procedure:
• Disconnect all water connections.
• Turn on the machine for a few seconds until the remaining
water in the pump exits. Turn o immediately.
• Do not allow the high-pressure hose to become kinked.
• Store the machine and accessories in a room that does
not reach freezing temperatures.
• Do not store near a furnace or other sources of heat that
may dry out the pump seals.
• Operate the pressure washer with non-corrosive/non-toxic
anti-freeze, a pump saver, or a pump protector before
storing for the winter.
mWARNING! Before reusing, completely ush the unit
out with clear water. Anti-freeze products can damage
paintwork, so you must ensure there is no anti-freeze left in the
system before using it again.
Maintenance
m
CAUTION! Before working on the pressure washer,
disconnect the plug from the power supply socket.
1. To ensure good performance, check and clean the adapter
lter (Fig. 21). Remove the lter and rinse with warm water
to prevent any foreign matter from clogging the pump
(Fig. 22).
12
Fig. 21
Garden hose
adaptor
Adapterlter
Fig. 22
2. Clean the nozzle with the needle clean-out tool provided
(Fig. 23). Remove the spray wand from the gun; remove
any dirt from the nozzle hole and rinse.
(FRONT)
Adapterlter
Disposal
Recycling the Washer
• Do not dispose of electrical appliances as unsorted
municipal waste. Use separate collection facilities.
• Contact your local government agency for information
regarding the collection systems available.
• If electrical appliances are disposed of in landlls
or dumps, hazardous substances can leak into the
groundwater and get into the food chain, damaging your
health and well-being.
• When replacing old appliances with new ones, the retailer
is legally obligated to take back your old appliance for
disposal at least free of charge.
Service + Support
If your Sun Joe® SPX4003 electric pressure washer requires
service or maintenance, please call the Snow Joe
customer service center at 1-866-SNOWJOE (1-866-766-9563).
®
+ Sun Joe®
Model + Serial Numbers
When contacting the company, reordering parts, or arranging
service from an authorized dealer, you will need to provide the
model and serial numbers, which can be found on the decal
located on the housing of the unit. Copy these numbers into
the space provided below.
Fig. 23
Needle clean-out tool
3. Remove additional debris by back ushing water through
the nozzle and spray wand. To do this, place the end of
your garden hose (with water running) to the tip of the
nozzle, pushing water and debris out of the back opening
of the nozzle and spray wand.
Record the following numbers from the housing or handle of your
new product:
S P X 4 0 0 3
Model #:
Serial #:
13
Troubleshooting
• Disconnect the unit from the electrical power supply before carrying out maintenance on the machine or when checking that
its parts are in proper working order.
• To avoid unnecessary hassles, consult the following table before contacting customer service with any mechanical issues.
Problems Possible Cause Possible Solution
Machine refuses
to start
Fluctuating pressure
Machine stops
Fuse blows
• Power failure/machine not
plugged into a working receptacle.
• Defective socket.
• Fuse has blown.
• Defective extension cord.
• Pump sucking air.
• Valves dirty, worn out, or stuck.
• Pump seals worn out.
• Fuse has blown.
• Incorrect mains voltage.
• Thermal sensor activated.
• Nozzle partially blocked.
• Fuse too small.
• Check to make sure machine is plugged into
a working outlet.
• Check the power cord and reset the GFCI.
Try a dierent outlet.
• Replace fuse. Switch o any other machines
that are using the same circuit.
• Try the unit without an extension cord.
• Check the hoses and connections are airtight.
• Clean or replace valves/seals.
• Please call the Snow Joe
service center at 1-866-SNOWJOE (1-866-766-9563)
for assistance.
• Replace fuse. Switch o other machines using
the same circuit.
• Check that the mains voltage corresponds to
specication on the model tag.
• Leave the washer for 5 minutes to cool down.
• Clean the nozzle.
• Install a fuse with a higher amp rating than the
amp consumption of the machine. Try the unit
without an extension cord.
®
+ Sun Joe® customer
Machine pulsating
Machine often starts
and stops by itself
Machine starts, but
no water comes out
• Air in inlet hose.
• Inadequate supply of mains water.
• Nozzle partially blocked.
• Water lter blocked.
• Hose kinked.
• Pump/spray gun is leaking.
• Trigger mechanism is broken.
• Pump/hoses or accessories frozen.
• No water supply.
• Water inlet lter blocked.
• Nozzle blocked.
• Allow machine to run by holding the trigger until
regular working pressure resumes.
• Check that the water supply corresponds to the
specications required.
• WARNING! Avoid using long, thin hoses
(minimum 1/2 in. diameter).
• Clean the nozzle.
• Clean the water inlet lter.
• Straighten out the hose to remove any kinks/blockages.
• Please call Snow Joe
center at 1-866-SNOWJOE (1-866-766-9563) for
assistance.
• Wait for pump/hoses or accessories to thaw.
• Connect inlet water.
• Clean the water inlet lter.
• Clean the nozzle.
®
+ Sun Joe® customer service
14
Optional Accessories
WARNING! ALWAYS use only authorized Snow Joe
m
replacement parts or accessories that are not intended for use with this electric pressure washer. Contact Snow Joe
if you are unsure whether it is safe to use a particular replacement part or accessory with your pressure washer. The use of any
other attachment or accessory can be dangerous and could cause injury or mechanical damage.
®
+ Sun Joe® replacement parts and accessories. NEVER use
®
+ Sun Joe®
ModelAccessories Item
1
25 ft Medium-Duty
High Pressure Extension Hose
(For SPX Pressure Washer Series)
2
Solid Brass Universal Quick Connector
(Garden Hose to Pressure Washer Adapter)
SPX-25H
SPX-UQC
3
Sun Joe® House + Deck All-Purpose Pressure
Washer Rated Concentrated Cleaner
Sun Joe
Washer Rated Car Wash Soap + Cleaner
Sun Joe
Washer Rated Cleaner + Degreaser
®
Premium Snow Foam Pressure
®
All-Purpose Heavy Duty Pressure
Sun Joe’s complete line of premium pressure washer accessories and attachments
make it easy to get your dirty work done, and also help you get the most out of your model!
SHOP ONLINE now at sunjoe.com
NOTE: Accessories are subject to change without any obligation on the part of Snow Joe
changes. Accessories can be ordered online at snowjoe.com or via phone by contacting the Snow Joe
service center at 1-866-SNOWJOE (1-866-766-9563).
®
+ Sun Joe® to provide notice of such
SPX-HDC1G
SPX-FCS1G
SPX-APC1G
®
+ Sun Joe® customer
15
NOTES
16
NOTES
17
NOTES
18
SNOW JOE® + SUN JOE® CUSTOMER PROMISE
ABOVE ALL ELSE, Snow Joe® + Sun Joe® are dedicated to you, our customer. We strive to make your experience as pleasant
as possible. Unfortunately, there are times when a product does not work or breaks under normal operating conditions. We
think it’s important that you know what you can expect from us. That’s why we created the Snow Joe® + Sun Joe® promise.
OUR PROMISE: Snow Joe® + Sun Joe® warrant new products for two years from the date of purchase. If your product does
not work, or there’s an issue with a specic part, we will x this by either sending you a free replacement part or by sending
you a new or comparable product at no charge. How cool is that! Before you know it, you’ll be back in action cutting,
sawing, mowing, washing and…?
PRODUCT REGISTRATION:
®
Snow Joe
, LLC (“Snow Joe® + Sun Joe®”) strongly encourages
you to register your purchase. You can register online at
snowjoe.com/ProductRegistration, or by printing and mailing
in a registration card available online from our website, or
calling our Customer Service Department at 1-866-SNOWJOE
(1-866-766-9563), or by e-mailing us at help@snowjoe.com.
Failure to register your product purchase will not diminish your
warranty rights. However, registering your purchase will allow
®
Snow Joe
+ Sun Joe® to better serve you with any of your
customer service needs.
WHO CAN SEEK WARRANTY COVERAGE?
®
This Warranty is extended by Snow Joe
+ Sun Joe® to the owner
of this Machine (a “Machine” consists of a product powered by
a motor) for residential and personal household use only. This
Warranty does not apply to products used for commercial, rental
or re-sale purposes. Should ownership of this machine change
during the 2-year period, please update the Machine’s owner
information at snowjoe.com/ProductRegistration.
WHAT IS COVERED?
®
Snow Joe
+ Sun Joe® warrants to the owner that if this Machine
fails within 2 years from the date of purchase due to a defect in
material or workmanship or as a result of normal wear and tear
®
from ordinary household use, Snow Joe
+ Sun Joe® will send a
replacement part or product, as needed, free of charge and with
free shipping to the original purchaser.
®
If, in Snow Joe
cannot be repaired with a part, Snow Joe
+ Sun Joe®’s sole discretion, the failed Machine
®
+ Sun Joe® will elect to
either (A) send a new Machine at no charge and with free shipping
or (B) refund the full purchase price to the owner.
WHAT IS NOT COVERED?
This Warranty does not apply to the Machines that have been used
commercially or in non-household applications. This Warranty
does not cover cosmetic changes that do not aect performance.
This Warranty is only valid if the Machine is used and maintained
in accordance with the instructions, warnings and safeguards
®
contained in the owner’s manual. Snow Joe
+ Sun Joe® will not
be responsible for the cost of any unauthorized warranty repairs.
This warranty does not cover any cost or expense incurred by
the purchaser in providing substitute equipment or service during
reasonable periods of malfunction or non-use of this product
while waiting for a replacement part or unit under this warranty.
Wearing parts like belts, augers, chains and tines are not covered
under this warranty, and can be purchased at snowjoe.com or
by calling 1-866-SNOWJOE (1-866-766-9563). Batteries are
covered in full for 90-days from the date of purchase.
Repair, replacement or refund of the purchase price are the
exclusive remedies of purchaser and the sole liability of Snow Joe
®
+ Sun Joe
of Snow Joe
under this warranty. No employee or representative
®
+ Sun Joe® is authorized to make any additional
®
warranty or any modication to this warranty which may be
®
binding upon Snow Joe
+ Sun Joe®. Accordingly, purchaser
should not rely upon any additional statements made by any
®
employee or representative of Snow Joe
+ Sun Joe®. In no event,
whether based on contract, indemnity, warranty, tort (including
®
negligence), strict liability or otherwise, shall Snow Joe
®
Sun Joe
be liable for any special, indirect, incidental, or
+
consequential damages, including, without limitation, loss of
prot or revenue.
Some states do not allow limits on warranties. In such states, the
above limitations may not apply to you.
Outside the USA, other warranties may apply.
19
snowjoe.com
Loading...