Sun SPX3000 User Manual

ELECTRIC PRESSURE WASHER
2030 PSI | 1.76 GPM | 14.5 AMP
Model SPX3000
A Division of Snow Joe®, LLC
IMPORTANT!
Safety Instructions
All Operators Must Read These Instructions Before Use
mWARNING! This indicates a hazardous situation, which,
if not avoided, could result in death or serious injury.
mCAUTION! This indicates a hazardous situation, which,
if not avoided, could result in minor or moderate injury.
mDANGER! This indicates a hazardous situation, which,
if not followed, will result in death or serious injury.
General Safety
WARNING! This appliance is not intended for use
m
by children or by unassisted, unsupervised persons whose physical, sensory or mental capabilities prevent them from using it safely. Children should be supervised to ensure that they do not play with the appliance.
Before starting up your machine, please check it carefully for
any defects. If you nd any, do not start up your machine.
Contact your authorized Snow Joe call the Snow Joe 1-866-SNOWJOE (1-866-766-9563).
®
+ Sun Joe® customer service center at
®
+ Sun Joe® dealer or
mWARNING! When using the pressure washer, basic
safety precautions should always be followed to reduce the
risk of re, electric shock, and personal injury. These include:
Know your product – Know how to stop the machine and
bleed pressure quickly. Thoroughly familiarize yourself with the controls.
Keep bystanders away – All visitors and pets should be
kept a safe distance away from the work area.
Use the right product – Do not use this machine for any
job except that for which it is intended.
Dress properly – Do not wear loose clothing or jewelry.
They can get caught in moving parts. Protective rubber gloves and non-slip footwear are recommended when working outdoors.
mCAUTION! – Exercise caution to avoid slipping or falling.
Wear protective footwear that will protect your feet and improve your footing on slippery surfaces.
Form No. SJ-SPX3000-880E-MR2
OPERATOR’S MANUAL
Stay alert – Watch what you are doing. Use common
sense. Do not operate the pressure washer when you are tired, or under the inuence of alcohol or drugs.
Do not overreach –
all times.
• Avoid unintentional starting – Do not carry a plugged-
in machine with your nger on the trigger. Make sure the switch is o before plugging in the machine.
Do not abuse the cord – Never carry the machine by the
cord or yank the cord to disconnect it from the receptacle. Keep the cord away from heat, oil, and sharp edges.
Use safety glasses – Also use safety footwear, snug-tting
clothing, protective gloves, hearing and head protection.
Check the water temperature – This pressure washer is
not meant to pump hot water. NEVER connect it to a hot
water supply as it will signicantly reduce the life of the
pump.
Store indoors – NEVER store the pressure washer
outdoors or where it could freeze. The pump could be seriously damaged.
Ground Fault Circuit Interrupter (GFCI) – Protection
should be provided on the circuits or outlets to be used for this pressure washer. Receptacles are available having built-in GFCI protection and may be used for this measure of safety.
• Inspect electrical cables – The insulation of the power cord should be perfectly intact. If the power cord is damaged or shows any signs of wear or tear, do not use the pressure washer. Contact your authorized Snow Joe
Sun Joe service center at 1-866-SNOWJOE (1-866-766-9563).
®
dealer or call the Snow Joe® + Sun Joe® customer
Keep proper footing and balance at
®
+
mWARNING! Do not use this appliance without reading
this instruction manual.
mWARNING! This appliance has been designed for
use with cleaning agents that are recommended by the manufacturer. The use of other cleaning agents or chemicals
may adversely aect the safety of the appliance.
mWARNING! Do not use the appliance within range of
persons unless they are wearing protective clothing.
mWARNING! High-pressure jets can be dangerous if
subject to misuse. The jet must not be directed at persons, pets, live electrical equipment, or the appliance itself.
• Do not direct the jet at yourself or others in order to clean
clothes or footwear.
Risk of explosion – Do not spray ammable liquids.
© 2014 by Snow Joe®, LLC All rights reserved. Original instructions.
1
Disconnect the tool – Disconnect from the electrical power
supply before performing any maintenance task.
Keep children away – This high-pressure electric
power washer must not be used by children or untrained personnel.
• To ensure appliance safety, use only original replacement
parts from the manufacturer or those approved by the manufacturer.
mWARNING! Water that has owed through backow
preventers is considered to be non-potable.
mWARNING! During cleaning, maintenance or when
replacing parts, the machine must be disconnected from its power source by removing the plug from the socket outlet.
mWARNING! High-pressure hoses, ttings, and
couplings are important for the safe operation of the appliance.
Use only hoses, ttings, and couplings recommended by the
manufacturer.
Check for damaged parts – Do not use the appliance if
the supply cord or other important parts of the appliance are damaged (e.g. safety devices, high-pressure hoses, trigger gun).
mWARNING! If an extension cord is used, the plug and
socket must be of watertight construction.
mWARNING! Inadequate extension cords can be
dangerous.
• This high-pressure electric power washer must not be used
at temperatures below 32ºF (0°C).
mWARNING! Power cords on drums should always be
completely unwound to prevent the cord from overheating.
• Power cord connections should be kept dry and o the
ground.
• If the power cord is damaged, do not use the appliance.
Contact your authorized Snow Joe® + Sun Joe® dealer or call the Snow Joe 1-866-SNOWJOE (1-866-766-9563).
• Keep the machine on a stable, at surface during operation,
handling, transportation, and storage. Sudden overturn of the machine can cause bodily injury.
• In the event of an accident or breakdown, switch o the
machine immediately. (If contact with detergent occurs, rinse with an abundance of clean water.)
®
+ Sun Joe® customer service center at
Electrical Safety
ATTENTION: If there are problems with the electrical
MAINS, short voltage drops may appear when starting the equipment. This can, in turn, inuence other equipment (e.g. cause a lamp to blink). If the MAINS-IMPEDANCE Zmax < 0.335 OHM, such disturbances are not expected. (If you require assistance, contact your local supply authority for further information.)
mWARNING! Electrical Shock Hazard – Before starting
up your machine, please check it carefully for any defects. If
you nd any, do not start up your machine and contact your
distributor.
The following should be observed when connecting the
high-pressure electric power washer to the electric supply:
• The electric supply connection should be performed by a qualied person.
• The electric supply to this appliance should include either
a residual current device that will interrupt the supply if the leakage current to the earth exceeds 30 mA for 30 ms or a device that will interrupt the earth circuit (GFCI).
IMPORTANT: Only use water without any impurities.
If there is a risk of running sand into the inlet water (i.e. from
your own well), an additional lter should be installed.
Safety devices
The unloader valve can reduce pressure if it exceeds preset values. The spray gun features a locking device. When the lock is activated, the spray gun cannot be operated.
1. Thermal sensor – A thermal sensor protects the motor against overloading. The machine will restart after a few minutes when the thermal sensor has cooled.
2. Double insulation – In a double-insulated appliance, two systems of insulation are provided instead of grounding. No grounding means is provided on a double-insulated appliance, nor should a means for grounding be added to the appliance. Servicing a double-insulated appliance requires extreme care and knowledge of the system, and
should be performed only by qualied service personnel at
an authorized Snow Joe parts for a double-insulated appliance must be identical to the parts they replace. A double-insulated appliance is marked with the words “Double Insulation” or “Double Insulated.” The symbol also be marked on the appliance.
3. Ground fault circuit interrupter (GFCI) protection – A GFCI should be provided on the circuit(s) or outlet(s) to be used for the pressure washer. Receptacles are available having built-in GFCI protection and may be used for this measure of safety.
4. It is not recommended to use an extension cord with this pressure washer. The unit comes standard with a 35 ft GFCI power cable. Using an extension cord may cause a drop in line voltage resulting in loss of power and overheating.
5. To reduce the risk of electric shock, this appliance has a polarized plug (i.e. one blade is wider than the other).
The appliance plug will t into a polarized outlet only one
way.
If the appliance plug does not t fully into the outlet,
reverse the plug. If the plug still does not t, make sure
that you are using the correct polarized wall outlet. If the
®
+ Sun Joe® dealer. Replacement
(square within a square) may
2
plug still does not t, contact a qualied electrician to
install the proper wall outlet. Do not modify the appliance plug, power cord receptacle, or power cord plug in any way.
m WARNING m
Electric shock may cause SEVERE INJURY or DEATH. Heed these warnings:
• Do not allow any part of the electric pressure washer
to make contact with water while it is in operation. If
the appliance becomes wet while turned o, wipe dry
before starting.
• Do not use an extension cord over 25 ft. The
pressure washer comes equipped with a 35 ft power cable. Combined cord length must not exceed 60 ft. Any extension cord must be 14-gauge (or heavier) to safely power the pressure washer.
• Do not touch the appliance or its plug with wet hands
or while standing in water. Wearing rubber boots
oers some protection.
EXTENSION CORD CHART
Cord Length:
Min. Wire Gauge (A.W.G.):
6. To prevent the appliance cord from disconnecting from the extension cord during operation, make a knot with the two cords as shown in Table 1.
25 ft (7.6 m)
14
Risk of electrocution
• Inspect cord before using.
Do not use if cord is damaged.
• Keep all connections dry and o the ground.
Do not touch plug with wet hands.
Keep cord away from heat and sharp edges.
• Do not spray electrical apparatus and wiring.
Risk of explosion
• Do not spray ammable liquids.
• Do not use acids, bases, solvents, or any ammable
material in this product. These substances can cause physical injuries to the operator and irreversible damage to the machine.
Additional safety instructions
• High-pressure: keep clear of nozzle.
• Injection hazard: equipment can cause serious injury if the
spray penetrates the skin.
• Do not point the gun at anyone or at any part of the body.
• In case of skin penetration, seek medical aid immediately.
• Before servicing, cleaning, or removing any parts, shut o
the power and relieve pressure.
• This machine is not suitable for connection to the potable
water mains.
Product Description
Table 1. Method of Securing Extension Cord
Cord set Appliance cord
(A) Tie cord as shown
(B) Connect plug and receptacle
7. Do not abuse the cord. Never pull the pressure washer
by the cord or yank the cord to disconnect it from the receptacle. Keep the cord away from heat, oil, and sharp edges.
Purpose
• This high-pressure electric power washer is intended for
residential use to clean vehicles, machines, buildings, facades, etc.
Areas of application
• Never use the machine in potentially explosive areas under
any circumstances!
• The operating temperature must be between 32ºF (0ºC) and
104ºF (40ºC).
• The machine consists of an assembly with a pump, which
is encased in a shock-absorbing housing. To provide the operator with an optimal working position, the machine is equipped with a spray wand and a non-slip handle grip,
whose shape and conguration comply with applicable
regulations.
• Do not cover or modify the spray wand or the spray nozzles
in any way.
• The high-pressure electric power washer is designed to be
used with cold or lukewarm water; higher temperatures can damage the pump.
• Do not use water that is dirty, gritty, or contains any
chemical products, as these could impair operation and shorten the life of the machine.
3
Safety Symbols
The following table depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate.
Symbols SymbolsDescriptions Descriptions
READ THE OPERATOR'S MANUAL(S) – Read, understand,
and follow all instructions in the user manual(s) before attempting to assemble and operate.
WARNING! Electrical shock hazard.
SAFETY ALERT – Indicates a
precaution, a warning, or a danger.
WEAR EYE AND HEARING PROTECTION – For protection
against injury, wear ear defenders and safety goggles.
Wear safety gloves during use to protect hands.
Store indoors. Never store the pressure washer outdoors. If the pump freezes, permanent damage may result.
WARNING! Do not expose the unit to rain or wet conditions. Keep dry.
To reduce the risk of injury, user must keep all bystanders at least 49 ft (15 m) away.
Wear non-slip footwear that will protect your feet and improve your footing on slippery surfaces.
Machine not suitable for connection to the potable water mains.
Always keep the power cable away from heat sources, oils, or sharp edges. Immediately remove plug from the mains if the cable is damaged, frayed, or entangled.
Sound power level is 96 dB(A).
WARNING! Turn the machine OFF and disconnect it from the power supply before inspecting, cleaning, changing accessories, or conducting any other maintenance task.
Double Insulation – When servicing, use only identical replacement parts.
4
Know Your Electric Pressure Washer
15º
25º
SOAP
40º
Read the owner’s manual and safety instructions carefully before operating the electric pressure washer. Compare the illustration below to the electric pressure washer in order to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference.
1. Safety lock (Locate lock in center of trigger. Pull up and snap in place. See Fig. 20, pg. 10)
2. Trigger
3. Transport handle
4. High-pressure hose connection
5. Trigger gun
6. Spray wand
7. Water inlet (garden hose connection)
8. Spray wand protector
9. High-pressure hose
10. Garden hose adaptor (female coupler)
11. Needle clean-out tool
12. 0º Quick-Connect nozzle (orange)
13. 15º Quick-Connect nozzle (yellow)
14. 25º Quick-Connect nozzle (green)
15. 40º Quick-Connect nozzle (gray)
16. Soap Quick-Connect nozzle (black)
17. Detergent selection dial
18. Removable detergent tanks
19. Hose holder
20. On/O switch
21. Power cord with GFCI
22. Cord holder
23. Onboard storage for Quick-Connect nozzles
24. Detergent tube
25. Trigger gun holder
26. Water outlet
(high-pressure connection)
27. Wheels 9
1 2 3
4
5
6
7
8
10
11
17
18
19
20
21
23
24
22
25
27
(REAR)(FRONT)
Technical Data
Rated Voltage 120 V ~ 60 Hz
Motor 14.5 amp (1800 W)
Max. Water Inlet Temperature 104ºF/40ºC
Max. Water Inlet Pressure 0.7 MPa
Max. Rated Flow 1.76 GPM
14122613 15 16
Rated Pressure 1450 PSI
Max. Pressure 2030 PSI
Hose Length 20 ft (6 m)
Power Cord Length 35 ft (10.7 m)
Weight 31 lbs (14 kg)
5
Unpacking
Assembly
Carton Contents
Electric pressure washer
Handle
Trigger gun
Spray wand
• Five (5) Quick-Connect nozzles (0º, 15º, 25º, 40º and Soap)
• Two (2) removable detergent tanks
• Four (4) large screws
• Two (2) small screws
Spray wand protector
Trigger gun holder
Hose holder
Needle clean-out tool
High-pressure hose
• Garden hose adaptor (female coupler) with two sealing rings
Manual with registration card
1. Carefully remove the pressure washer and check to see that all of the above items are supplied.
2. Inspect the product carefully to make sure no breakage or
damage occurred during shipping. If you nd damaged or
missing parts, DO NOT return the unit to the store. Please call the Snow Joe
1-866-SNOWJOE (1-866-766-9563).
NOTE: Do not discard the shipping carton and packaging
material until you are ready to use your new electric pressure washer. The packaging is made of recyclable materials. Properly dispose of these materials in accordance with local regulations.
IMPORTANT! The equipment and packaging material are not toys. Do not let children play with plastic bags, foils, or small parts. These items can be swallowed and pose a
suocation risk!
®
+ Sun Joe® customer service center at
1. Position the washer as CLOSE as possible to the water supply.
2. The washer must be used on a secure and stable surface in a standing, upright position (Fig. 1).
Fig. 1
3. Slide the trigger gun holder into position (Fig. 2).
Fig. 2
4. Slide the handle into position and secure it with 4 large
screws (Fig. 3).
mWARNING! Do not connect to power supply until
assembly is complete. Failure to comply could result in accidental starting and possible serious personal injury.
Fig. 3
4 large screws
6
Loading...
+ 14 hidden pages