Stryker 6254 Operation & Maintenance Manual

Evacuation Chair

Chaise d’évacuation/Evakuierungsstuhl

Evacuatiestoel/Sedia per evacuazione

Silla de evacuación/Cadeira de evacuação

Evakueringsstol/Evakuointituoli

Αμαξίδιο εκκένωσης/Krzesło do ewakuacji

REF

Model/Modèle/Modell/Modello/Modelo/Malli/Μοντέλο 6254

Operations/Maintenance Manual

Manuel d’utilisation et d’entretien

Bedienungs- und Wartungshandbuch

Gebruiks-/onderhoudshandleiding

Manuale d’uso e manutenzione

Manual de uso y mantenimiento

Manual de funcionamento/manutenção

Betjenings-/vedligeholdelsesmanual

Användar-/underhållshandbok

Käyttö- ja huolto-ohjekirja

Εγχειρίδιο λειτουργίας/συντήρησης

Instrukcja obsługi/konserwacji

2012/02 A.1 6254-109-005 REV A www.stryker.com

International Addresses

UK/IRELAND

Stryker UK Limited

Stryker House
Hambridge Road

EUROPE HEADQUARTERS

Stryker SA

Cite-Centre, Grand-Rue 90

P.O. Box 1568
1820 Montreux, Switzerland
Phone: [phone]

Fax: [phone]

EASTERN EUROPE

Stryker SA - Export Business
Grand-Rue 90
P.O. Box 1567
1820 Montreux, Switzerland
Phone: [phone]
Fax: [phone]

AUSTRALIA

Stryker Australia

8 Herbert Street
St Leonards NSW 2065
Australia
Phone: [phone]
Fax: [phone]

AUSTRIA

Stryker-Howmedica Osterreich GmbH
Millenium Tower
Handelskai 94-96
120 Wien
Austria
Phone: [phone]
Fax: [phone]

BELGIUM

NV Stryker SA

Ikaros Business Park- Fase III
Ikaroslaan 12
1930 Zaventem, Brussels
Belgium
Phone: [phone]
Fax: [phone]

DENMARK

Stryker Denmark

Filial of Stryker AB
Postbox 772
1532 Copenhagen
Denmark
Phone: [phone]
Fax: [phone]

Newbury, Berkshire
RG14 5EG, England
Phone: [phone]
Phone: [phone]
Fax: [phone]

FINLAND

Stryker AB, Finland

PO 80 Makelankatu 2
00501 Helsinki
Finland
Phone: [phone]
Fax: [phone]

FRANCE

Stryker France SA

ZAC - Avenue de Satolas Green
69330 Pusignan
France
Phone: [phone]
Fax: [phone]

GERMANY

Stryker Howmedica GmbH

Dr. Homer Stryker Platz 1
47228 Duisburg
Germany
Phone: [phone]
Fax: [phone]

GREECE

Stryker Hellas EPE

455 Messogion ave
153 43 Agia Paraskevi
Athens, Greece
Phone: [phone]
Fax: [phone]

ITALY

Stryker Italia SrL

Via Ghisalba 15B
00188 Roma
Italy
Phone: [phone]
Fax: [phone]

MIDDLE EAST / NORTH AFRICA

Stryker Osteonics SA

Twin Towers
11th Floor, Suite 1101 & 1102
P.O. Box 41446
Baniyas Road
Dubai, Deira, UAE
Phone: [phone]
Fax: [phone]

NEDERLANDS

Stryker Nederlands BV
(P.O. Box 13, 4180 BA Waardenburg)
4181 CD Waardenburg
The Nederlands
Phone: [phone]
Fax: [phone]

NORWAY

Stryker Norway

Norsk Fillial
Nedre Vollgate 3
0158 Oslo
Norway
Phone: [phone]
Fax: [phone]

POLAND

Stryker Polska Sp. ZO.O

Kolejowa 5/7
01-217 Warsawa
Poland
Phone: [phone]
Fax: [phone]

PORTUGAL

Stryker Portugal Produtos
Medicos, LTDA.

Avenida Marechal Gomes
da Costa, 35
1800-255 Lisboa
Portugal
Phone: [phone]
Fax: [phone]

ROMANIA

Stryker Osteonics Romania S.R.L.

19, Leonida Str.
District 2
7000 Bucharest
Romania
Ph one: 011-40-2-12-12-11-22
Fa x: 011- 4 0 -2-12-12-11-33

SOUTH AFRICA

Stryker Osteonis PTY. LTD.

3 Susan Street
Strydom Park
Johannesburg, 2194 - South Africa
Mailing Address:
P.O. Box 48039
2129 Roosevelt Park
Johannesburg, South Africa
Phone: [phone]
Fax: [phone]

SPAIN

Stryker Iberia SL

c/Sepulveda n17
28108 Alcobendas
Madrid
Spain
Phone: [phone]
Phone: [phone]
Fax: [phone]

SWEDEN

Stryker AB/Scandinavia

Box 50425
SE-204 14 Malmo
Sweden
Phone: [phone]
Fax: [phone]

Table of Contents

Symbols and Definitions ...................................................................1-5

Symbols ...........................................................................1-5

Warning / Caution / Note Definition........................................................1-5

Introduction ............................................................................1-6

Product Description ...................................................................1-6

Intended Use of Product................................................................1-6

Specifications .......................................................................1-6

Component Identification ...............................................................1-7

Summary of Safety Precautions .............................................................1- 8

Setup Procedures........................................................................1-9

Instructions............................................................................1-10

Operation Guide........................................................................1-1 1

Operating Guidelines ................................................................1-11

Unfolding the Chair ..................................................................1-12

Folding the Chair ....................................................................1-12

Transferring the Passenger to the Stryker Evacuation Chair ....................................1-13

Using Restraint Straps ................................................................1-14

Proper Lifting Techniques..............................................................1-17

Transporting the Passenger on Flat Surfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-18

Transporting the Passenger Down Stairs ..................................................1-19

Transporting the Passenger Up Stairs.....................................................1-21

Operating the Wheel Locks ............................................................1-22

Using the Head Support ...............................................................1-23

Using Additional Assistance ............................................................1-24

Installing the Optional Wall Storage Bracket ................................................1-25

Installing the Optional Cabinet ..........................................................1-2 6

Installing the Optional Cover............................................................1-2 7

Removing the Optional Cover...........................................................1-2 7

Cleaning..............................................................................1-28

Washing Procedure ..................................................................1-28

Washing Limitations ..................................................................1-2 8

Preventative Maintenance .................................................................1-3 0

Checklist ..........................................................................1-31

Maintenance Record.....................................................................1-32

Training Record ........................................................................1-33

Quick Reference Replacement Part List ......................................................1-34

Service Information......................................................................1-35

Adjusting the Wheel Locking Force.......................................................1-35

Track Belt Reconditioning .............................................................1-36

Upper Control Handle Cable Replacement .................................................1-3 8

English

www.stryker.com 6254 -109- 005 REV A 1-3

English

Table of Contents

Warranty .............................................................................1-3 9

Stryker EMS Return Policy .............................................................1-40

Return Authorization..................................................................1-40

Damaged Merchandise ...............................................................1-40

International Warranty Clause...........................................................1-40

Patent Information ...................................................................1-40

Return To Table of Contents

1-4 6254-109-005 REV A www.stryker.com

Symbols and Definitions

SYMBOLS

Warning/Caution: consult accompanying documentation

Maximum Weight

Do Not Lubricate

Manufacturer

WARNING / CAUTION / NOTE DEFINITION

English

The words WARNING, CAUTION and NOTE carry special meanings and should be carefully reviewed.

WARNING

Alerts the reader about a situation which, if not avoided, could result in death or serious injury. It may also describe
potential serious adverse reactions and safety hazards.

CAUTION

Alerts the reader of a potentially hazardous situation which, if not avoided, may result in minor or moderate injury to the
user or passenger or damage to the equipment or other property. This includes special care necessary for the safe and
effective use of the device and the care necessary to avoid damage to a device that may occur as a result of use or
misuse.

NOTE

Provides special information to make maintenance easier or important instructions clearer.

Return To Table of Contents

www.stryker.com 6254 -109- 005 REV A 1-5

English

Introduction

This manual is designed to assist you with the operation and maintenance of Stryker Model 6254 Evacuation Chair.
Read this manual thoroughly before using the equipment or beginning maintenance on it. To ensure safe operation of
this equipment, it is recommended that methods and procedures be established for educating and training staff on the
safe operation of this chair.

PRODUCT DESCRIPTION

The Stryker Model 6254 Evacuation Chair is used for the evacuation of disabled persons from multilevel facilities.

INTENDED USE OF PRODUCT

The Stryker Model 6254 Evacuation Chair is a hand carried device, consisting of a light weight frame, on which a
person can be carried. It is intended to aid in the transportation of passengers up and/or down a flight of stairs in
an evacuation situation. The tracks allow a single operator to evacuate passengers weighing up to 200 pounds. Two
operators can manage passengers up to 500 pounds.

SPECIFICATIONS

Maximum Weight

1

500 lb 228 kg

Height 45” 114 cm

Width

Depth

2

20.5” 52 cm

28” 71 cm

Folded Depth 11” 28 cm

Weight 34 lb

Dimensions are measured from the outermost edges of the main frame. Specifications are rounded. Conversions are calculated
before rounding.

1

Maximum load capacity is total weight distributed in accordance to basic human anatomy. Operators must consider the weight

of the passenger, equipment, and accessories when determining the total load on the product.

2

Depth dimensions are measured with extendable handles retracted.

Stryker reserves the right to change specifications without notice.

15.5 kg

Return To Table of Contents

1-6 6254-109-005 REV A www.stryker.com

COMPONENT IDENTIFICATION

Stair-TREAD™

(Seat components

removed for clarity)

Introduction

English

Upper

Control Handle

Stair-TREAD™

Lock Bar

Wheel Lock

Lift Handle

Release Button

Front Caster

Upper Control Handle

Release Cable

Chair Fold

Lock Bar

Lift Handle

Release Button

Foot End Lift

Handles

Return To Table of Contents

www.stryker.com 6254 -109- 005 REV A 1-7

English

Summary of Safety Precautions

The following is a list of safety precautions that must be observed when operating or servicing this unit. The precautions
are repeated throughout the manual, where applicable. Carefully read this list before using or servicing the unit.

WARNING

• Improper usage of the Stryker Evacuation Chair can cause injury to the passenger or operator. Operate the Stryker
Evacuation Chair only as described in this manual.

• Do not modify the Stryker Evacuation Chair. Modifying the chair can cause unpredictable operation resulting in
injury to the passenger or operator. Modifying the chair will also void its warranty.

• Improper maintenance can cause injury or damage to the unit. Maintain the Stryker Evacuation Chair as described
in this manual. Use only Stryker approved parts and maintenance procedures. Using unapproved parts and
procedures could cause unpredictable operation and/or injury and will void the product warranty.

• Do not allow untrained helpers to assist in the operation of the Stryker Evacuation Chair. Untrained technicians/
helpers can cause injury to the passenger or themselves.

• An unlocked chair can fold during use, causing injury to the passenger or operator. Always make sure the chair is
locked in the unfolded position before use.

• To avoid injury, always verify the lift handles are locked in place before using them to lift the chair.

• Always use all restraint straps to secure the passenger on the chair. An unrestrained passenger may fall from the

chair and be injured.

• Never leave a passenger unattended on the chair or injury could result. Hold the chair securely while a passenger
is on the chair.

• The Stryker Evacuation Chair is not recommended for use with suspected cervical, spinal, or fracture injuries.

• To avoid injury when a passenger weighing more than 200 pounds is on the chair, use a minimum of two operators

to transport on stairs. If more people are required to safely control the chair, see page 1-24 for the proper
positioning of each helper.

• Only use the wheel locks during passenger transfer or without a passenger on the chair. Tipping could occur if
the chair is moved while wheel locks are applied, resulting in injury to the passenger or operator and/or damage
to the chair.

• Never use a wheel lock on a chair with excessively worn wheels. Using a wheel lock on a wheel with less than a
5” diameter could compromise the holding ability of the wheel lock, possibly resulting in injury to the passenger or
operator and/or damage to the chair or other equipment.

• To avoid injury, always verify the Stair-TREAD™ system is securely locked in place before transporting the
passenger.

• Water, ice and debris on the stairs can affect operator footing and proper operation of the Stair-TREAD™ system.
To avoid injury, clear the path or consider an alternate route.

• Condensation, water, ice and/or debris on the Stair-TREAD™ system can cause unpredictable performance,
resulting in a sudden change in the weight the operators must support. To avoid injury, and to aid proper operation
of the Stair-TREAD™ system, ensure the belts are clean and dry before transporting the passenger.

• Never lubricate the Stair-TREAD™ system. Lubrication on the system can cause inconsistent operation possibly
resulting in injury to the passenger or operator.

• To avoid injury to the operators and/or the passenger, operators should never attempt to transport passenger loads
greater than what they can safely lift.

• Do not sand the track teeth. Deformation of the teeth can cause unpredictable chair performance resulting in injury
to the operators and/or passenger.

CAUTION

• Casters are not suitable for all surfaces. Caution should be used at all times.

• Wheel locks are only intended to help prevent the empty chair from rolling while unattended and to aid in passenger

transfer. The wheel lock may not provide sufficient resistance on all surfaces or under loads.

• Release the red track release bar before clicking the Stair-TREAD™ system into the locked position. Failure to follow
this procedure could result in the track failing to lock. Always verify the Stair-TREAD™ system is locked by trying
to fold it before descending stairs.

Return To Table of Contents

1-8 6254-109-005 REV A www.stryker.com

Setup Procedures

Unpack the cartons and check all items for proper operation. It is important that the Stryker Evacuation Chair is
working properly before it is put into service. Have a qualified service person use the following list and the operation
instructions to check the chair before it is put into service.

• All fasteners secure (reference all assembly drawings).

• All welds intact, not cracked or broken.

• No bent or broken tubing or sheet metal.

• No debris in wheels.

• All wheels secure and rolling properly.

• Chair unfolds and locks properly.

• No or cracks in seat or backrest.

• Passenger restraints intact and working properly.

• Wheel locks operating properly.

• Foot end lift handles extend and lock properly.

• Head end lift handles fold and unfold.

• Casters secure, rolling and swiveling properly

• Upper control handle extends and locks in both positions

• Stair-TREAD™ system unfolds and locks

• Track belts roll properly

• Optional accessories intact and operating properly

English

WARNING

• Improper usage of the Stryker Evacuation Chair can cause injury to the passenger or operator. Operate the Stryker
Evacuation Chair only as described in this manual.

• Do not modify the Stryker Evacuation Chair. Modifying the chair can cause unpredictable operation resulting in injury
to the passenger or operator. Modifying the chair will also void its warranty.

Return To Table of Contents

www.stryker.com 6254 -109- 005 REV A 1-9

English

Instructions

These instructions are printed on the backrest of the Evacuation Chair.

To use the evacuation chair:

1. Stand behind the chair and pull the backrest and extension handle apart to unfold the chair.

WARNING

An unlocked chair can fold during use, causing injury to the passenger or operator. Always make sure the chair is locked
in the unfolded position before use.

2. Pull the red release cable with one hand and pull up on the control handle with the other hand to extend the upper
control handle.

3. Squeeze the red track release bar against the black cross tube. Relax your grip on the release bar and forcefully
pull the Stair-TREAD™ system to the fully extended position until both sides lock securely. Always verify both sides
of the Stair-TREAD system are locked by trying to fold it back up.

CAUTION

Release the red track release bar before clicking the Stair-TREAD system into the locked position. Failure to follow this
procedure could result in the track failing to lock. Always verify the Stair-TREAD system is locked by trying to fold it
before descending stairs.

4. Tilt the chair back just far enough to allow the Stair-TREAD system to contact the floor.

5. Maintaining the angle, guide the Evacuation Chair over the edge of the stairs, allowing the Stair-TREAD system to
engage the first step.

6. Glide down the stairs until the treads are level across the edges of two or three steps.

Return To Table of Contents

1-10 6254 -109- 005 REV A www.stryker.com

Operation Guide

OPERATING GUIDELINES

• Use the Stryker Evacuation Chair only as described in this manual.

• Read all labels and instructions on the chair before using the chair.

• Do not roll the chair, ascend, or descend stairs without advising the passenger. Stay with the passenger and

control the chair at all times.

• Only use the wheel locks during passenger transfer or without a passenger on the chair.

• Always use the restraint straps when a passenger is on the chair.

• Use properly trained helpers when necessary to control the chair and passenger.

• Store the Evacuation Chair in a cool, dry environment that is above freezing temperature and out of direct sunlight.

WARNING

• Always use all restraint straps to secure the passenger on the chair. An unrestrained passenger may fall from the
chair and be injured.

• Only use the wheel locks during passenger transfer or without a passenger on the chair. Tipping could occur if the
chair is moved while the wheel locks are applied, resulting in injury to the passenger or operator and/or damage
to the chair.

• Condensation, water, ice and/or debris on the Stair-TREAD™ system can cause unpredictable performance,
resulting in a sudden change in the weight the operators must support. To avoid injury, and to aid proper operation
of the Stair-TREAD™ system, ensure the belts are clean and dry before transporting the passenger.

• To avoid injury to the operators and/or the passenger, operators should never attempt to transport passenger loads
greater than what they can safely lift.

English

Return To Table of Contents

www.stryker.com 6254 -109- 005 REV A 1-11

English

Operation Guide

UNFOLDING THE CHAIR

To unfold the chair:

1. Stand behind the chair.

2. Apply the wheel locks (if desired).

3. Pull the backrest and the extension handle apart. The lock mechanism will automatically engage when the chair
is completely unfolded.

4. Verify the lock is engaged by pulling up on the seat. If the lock is properly engaged, the chair will not fold.

WARNING

An unlocked chair can fold during use, causing injury to the passenger or operator. Always make sure the chair is locked
in the unfolded position before use.

RED FOLD
LOCK BAR

Figure 1- Unfolding/Folding the Chair

FOLDING THE CHAIR

To fold the chair:

1. Apply the wheel locks (if desired). Buckle the restraint straps and fold them neatly to prevent them from interfering
with proper folding of the chair. Secure the head support strap behind the chair frame.

2. Stand at the side of the chair.

3. Pull up on the red lock bar at the rear of the chair.

4. Tip the chair forward.

5. Fold the seat up to the backrest until the front legs lock in the clips on the bottom of the seat tube.

Note: Rotate the front casters so they do not interfere with folding the chair.

Store the Evacuation Chair in a cool, dry environment that is above freezing temperature and out of direct sunlight.

Return To Table of Contents

1-12 6254-109 -0 05 REV A www.stryker.com

Operation Guide

TRANSFERRING THE PASSENGER TO THE STRYKER EVACUATION CHAIR

To transfer the passenger to the chair:

1. Place the chair beside the passenger.

2. Apply the wheel locks to prevent the chair from moving.

3. Open the restraint straps.

4. Extend the upper control handle.

5. Transfer the passenger to the chair.

6. Use all the restraints to secure the passenger on the chair (page 1-14).

7. Disengage the wheel locks before transporting.

WARNING

The Stryker Evacuation Chair is not recommended for use with suspected cervical, spinal, or fracture injuries.

English

Return To Table of Contents

www.stryker.com 6254 -109- 005 REV A 1-13

English

Operation Guide

USING RESTRAINT STRAPS

HEAD SUPPORT

RESTRAINT STRAPS

Figure 2 - Strap Attachment Points

Front View

Figure 3 - Lap Strap Attachment Points

Top View

WARNING

Always use all restraint straps to secure the passenger on the chair. An unrestrained passenger may fall from the chair
and be injured.

Always secure the passenger on the chair with all restraint straps. Buckle one restraint across the passenger’s chest
and the other across the passenger’s lap. Buckle the ankle restraint across the passenger’s legs.

To avoid damage to the buckles and straps, keep the restraint straps buckled when the chair is not being used with a
passenger.

When attaching the restraint straps to the chair, remember the attachment points must provide strong anchorage and
proper restraint position while not interfering with equipment and accessories.

Return To Table of Contents

1-14 6254 -109- 005 REV A www.stryker.com

Operation Guide

USING RESTRAINT STRAPS - CONTINUED

To attach the chest straps:

1. Wrap each strap around the chair frame, insert the end through
the loop on the end of the strap and pull it tight.

2. Pull the strap across the passenger’s chest, lengthening the
strap as necessary.

3. Buckle the strap.

4. Pull the loose end of the strap to tighten it securely around
the passenger.

5. Repeat for the second strap and the lap belt.

English

Figure 6 - Lengthen strap as necessary

Figure 4 - Insert the end through the loop

Figure 5 - Pull the strap tight

Figure 7 - Buckle strap

Figure 8 - Tighten strap securely

Return To Table of Contents

www.stryker.com 6254 -109- 005 REV A 1-15

English

Operation Guide

USING RESTRAINT STRAPS - CONTINUED

To attach the ankle strap:

1. Remove the three plastic pieces from the
strap.

2. Thread the strap through one of the
plastic “D” rings and slide the ring down to
the end of the strap up to the white label.

3. Loop the strap around the front leg of
the chair and pull the loose end of the
strap through the ring. Pull until the
ring rests against the foot rest tube.

4. Thread the strap through the other “D”
ring.

5. Loop the strap around the other front leg
of the chair and pull the loose end of
the strap through the loop. Pull until the
“D” ring rests against the foot rest tube.

6. Attach the final “male” end clip on the
strap.

Figure 9-17 - Attaching the leg strap

Return To Table of Contents

1-16 6254 -109-00 5 REV A www.stryker.com

Operation Guide

USING RESTRAINT STRAPS - CONTINUED

• To lengthen the restraint, grasp the buckle, turn it at an angle to the webbing and pull it out. A hemmed tab at
the end of the webbing prevents the buckle from coming off the strap.

• To shorten the restraint, grasp the hemmed tab and pull the webbing back through the buckle until the required
tightness is achieved.

• When the chair is put into service, open the restraints and place them at either side of the chair until the passenger
is positioned on the seat. Lengthen the restraint, buckle it around the passenger and shorten it until the required
tightness to properly secure the passenger is achieved.

• To open the restraint, press the tabs on the side of the buckle to release the buckle and pull the tang out of the
receiver.

• To close the restraint, push the tang into the receiver until a “click” is heard.

• Whenever a restraint is buckled on a passenger, the attendant should verify the tang is locked and the extra

webbing is not tangled in the chair or hanging loose.

• Inspection of the restraints should be done at least once a month (more frequently if used heavily). Inspection
should include checking for a bent or broken receiver or tang, torn or frayed webbing, etc. Any restraint showing
wear or not operating properly must be replaced immediately.

English

PROPER LIFTING TECHNIQUES

When lifting the Stryker Evacuation Chair and passenger, remember these five basic guidelines:

• Keep your hands close to your body.

• Keep your back straight.

• Coordinate your movements with your partner and lift with your legs.

• Avoid twisting.

• Always operate the Stryker Evacuation Chair as described in this manual.

Return To Table of Contents

www.stryker.com 6254 -109- 005 REV A 1-17

English

Operation Guide

TRANSPORTING THE PASSENGER ON FLAT SURFACES

WARNING

To avoid the risk of patient injury or equipment damage, do not allow the patient to stand on the footrest.

Figure 18 - Transporting the Passenger

To roll the Stryker Evacuation Chair over flat surfaces, push and guide the chair from the rear of the passenger, using

either the head end handles or the backrest tube. Lift the chair over and around obstructions with the head end and
foot end lift handles.

In addition to the head end lift handles, the extendable upper control handle can be used in any position to roll and
guide the chair. Extend the upper control handle by pulling the red release cable with one hand, and pulling up on the
control handle with the other. Release the cable to lock the handle in either the intermediate or fully extended position.
Lift the chair over and around obstructions with the head end and foot end lift handles.

CAUTION

Casters are not suitable for all surfaces. Caution should be used at all times.

Return To Table of Contents

1-18 6254 -109-00 5 REV A www.stryker.com

Operation Guide

TRANSPORTING THE PASSENGER DOWN STAIRS

WARNING

• To avoid injury, always verify the Stair-TREAD™ system is locked
in place before transporting the passenger.

• To avoid injury when a passenger weighing more than 200 pounds
is on the chair, use a minimum of two operators to transport on
stairs. If more people are required to safely control the chair, see

page 1-24 for the proper positioning of each helper.

• To avoid injury, always verify the lift handles are locked in place
before using them to lift the chair.

English

1. Roll the chair to the stairs and align it squarely with the edge of
the first step.

2. Foot end operator (if necessary) - Extend the foot end lift handles
by pushing the red release buttons and pulling the handles out
until they stop. Release the buttons and verify the handles are
locked.

3. Head end operator - Use one hand to pull the red upper control
handle release cable while using the other hand to pull up and
fully extend the handle. Release the cable and verify the handle
is locked on both sides in the fully extended position.

4. Head end operator - Squeeze the red track release bar against
the black cross tube. Relax your grip on the release bar and
forcefully pull the Stair-TREAD™ system to the fully extended
position until both sides lock securely. Always verify both sides of
the Stair-TREAD™ system are locked by trying to fold it back up.

CAUTION

Release the red track release bar before clicking the Stair-TREAD™
system into the locked position. Failure to follow this procedure could
result in the track failing to lock. Always verify the Stair-TREAD™
system is locked by trying to fold it before descending stairs.

Figure 19 - Foot end lift handles

Release Cable

Figure 20 - Upper control handle release

cable

Figure 21 - Red track release bar

5. Operators face each other while descending the stairs.

6. Head end operator - Tilt the chair back just far enough to allow
the Stair-TREAD™ system to contact the floor.

Figure 22 - Tilt the chair

Return To Table of Contents

www.stryker.com 6254 -109- 005 REV A 1-19

English

Operation Guide

TRANSPORTING THE PASSENGER DOWN STAIRS - CONTINUED

7. Both operators - Maintaining the angle, guide the Stryker
Evacuation Chair over the edge of the stairs, allowing the Stair­TREAD™ system to engage the first step.

8. Both operators - Glide down the stairs until the treads are level
across the edges of two or three steps.

9. Head end operator - Apply slight downward pressure on the
extendable upper control handle while the foot end operator
applies slight upward pressure on the foot end lift handles to
keep the chair from rocking forward as it glides down the stairs.

WARNING

• The Stair-TREAD™ system may not work the same on all
stair surfaces and in all environmental conditions. Based on
conditions, varying amounts of resistance may be encountered.
Avoid getting dirt or other obstructions inside the tracks. Water, ice
and/or debris on the stairs can affect operator footing and proper
operation of the Stair-TREAD™ system. To avoid injury, clear the
path or consider an alternate route. Condensation, water, ice and/
or debris on the Stair-TREAD™ system can cause unpredictable
performance, resulting in a sudden change in the weight the
operators must support.

• To avoid injury, and to aid proper operation of the Stair-TREAD™
system, ensure the belts are clean and dry before transporting the
passenger.

• To avoid injury to the operators and/or the passenger, operators
should never attempt to transport passenger loads greater than
what they can safely lift.

Figure 23 - Track engaging first step

Figure 24 - Transporting down the stairs

10. Foot end operator (if necessary) - when the track reaches the
last step, release the front handles. Head end operator - allow the
chair to tip forward until all four wheels are on the ground. Roll
the chair as described on page 1-18.

11. To fold the Stair-TREAD™ system, pull the red track release bar
toward the black cross bar and fold the track up toward the chair.
Verify the Stair-TREAD™ system is locked in place.

Figure 25 - “Resting position”

CAUTION

Release the red track release bar before clicking the Stair-TREAD™
system into the locked position. Failure to follow this procedure could
result in the track failing to lock. Always verify the Stair-TREAD™
system is locked by trying to fold it before descending stairs.

If, while descending the stairs, either operator needs to pause or rest,
tilt the chair forward just enough to allow the rear wheels to rest in
the crook of the stair. To continue down the stairs from the resting
position, the head end operator exerts slight downward pressure on
the upper control handle while the foot end operator provides slight
upward pressure to tilt the chair back and engage the Stair-TREAD™
system.

Return To Table of Contents

1-20 6254-109 -0 05 REV A www.stryker.com

Figure 26 - Bottom of stairs

Operation Guide

TRANSPORTING THE PASSENGER UP STAIRS

WARNING

• To avoid injury when a passenger weighing more than 200 pounds
is on the chair, use a minimum of two operators to transport on
stairs. If more people are required to safely control the chair, see

page 1-24 for the proper positioning of each helper.

• To avoid injury, always verify the lift handles are locked in place
before using them to lift the chair.

English

1. Roll the chair to the bottom of the stairs with the passenger’s back
to the stairs.

2. Foot end operator - extend the foot end lift handles by pushing the
red buttons and pulling the handles until they stop. Release the
button and verify the handle is locked.

3. Head end operator - unfold the head end lift handles.

4. The foot end operator faces up the stairs. The head end operator
may either face backward for improved passenger monitoring or
forward for an improved view of the stairs and easier maneuvering
around obstacles.

Note: Although the head end operator can face either direction
while carrying, any applicable protocols for carrying chairs should
be followed.

5. Both operators - simultaneously lift the chair, using the head and foot
end lift handles and following proper lifting techniques (see page

1-17). Carry the chair slowly up the stairs, avoiding any obstructions.

Figure 27 - Foot end lift handles

Figure 28 - Head end lift handles

Figure 29 - Transporting up the stairs

Figure 30 - Transporting up the stairs

Return To Table of Contents

www.stryker.com 6254 -109- 005 REV A 1-21

English

Operation Guide

OPERATING THE WHEEL LOCKS

A

Figure 31 - Wheel Locks

To activate the wheel locks:

1. Press down on the pedals (A) until they stop.

2. To release the wheel locks, depress the upper face of the pedal with your foot or lift up with your toe under the
pedal. The upper portion of the pedal will rest against the chair frame when the wheel lock is released.

WARNING

• Only use wheel locks during passenger transfer or without a passenger on the chair. Tipping could occur if the
chair is moved while the wheel locks are applied, resulting in injury to the passenger or operator and/or damage
to the chair.

• Wheel locks are only intended to help prevent the empty chair from rolling while unattended, and to aid in
passenger transfer. A wheel lock may not provide sufficient resistance on all surfaces or under loads.

• Never leave a passenger unattended on the chair or injury could result. Hold the chair securely while a passenger
is on the chair.

• Never use a wheel lock on a chair with excessively worn wheels. Using a wheel lock on a wheel with less than a
5” diameter could compromise the holding ability of the wheel lock, possibly resulting in injury to the passenger or
operator and/or damage to the chair or other equipment.

Return To Table of Contents

1-22 6254-109-005 REV A www.stryker.com

USING THE HEAD SUPPORT

Operation Guide

English

TOP VIEW

Upper Control Handle

Figures 32 - 34 - Attaching and using the head support

Slide Ring

Head Support

WARNING

The Stryker Evacuation Chair is not recommended for use with suspected cervical, spinal, or fracture injuries.

Before using the head support, the upper control handle must be extended. First, pull the red upper control handle
release cable with one hand. Then, pull up on the handle with the other hand. Release the cable and verify the handle
is securely locked into one of the two available positions.

To attach the head support to the extendable upper control handle:

1. Wrap the loose ends of the strap around the vertical portions of the handle, then feed them through the plastic
loops.

2. Pull tight, and secure the strap to itself.

3. Adjust the height by loosening the strap, moving it to the desired location, and tightening it again.

To support the passenger’s head, position at the base of the head. For unconscious, or semiconscious passengers,
secure the head using the other two parts of the strap. Wrap around the passenger’s head, and overlap the straps to
the desired tightness to secure. When not in use, these straps can be wrapped back around the handle and attached
to the back of the support.

Return To Table of Contents

www.stryker.com 6254 -109- 005 REV A 1-23

English

Operation Guide

USING ADDITIONAL ASSISTANCE

WARNING

To avoid injury when a passenger weighing more than 200 pounds is on the chair, use a minimum of two operators to
transport on stairs.

Down Stairs Up Stairs

One Operator

Operator

Two Operators

Two Operators

One Helper

Two Operators

Two Helpers

Operator Operator

Operator OperatorHelper Helper OperatorOperator

Helper Operator

Operator

Helper Operator

Helper Operator

Helper

Operator Operator

Helper Operator

Helper Operator

Helper

Helper

Two Operators

Three Helpers

Operator

Return To Table of Contents

1-24 6 254-109- 005 RE V A www.stryker.com

Helper

Operator

Helper

Operation Guide

INSTALLING THE OPTIONAL WALL STORAGE BRACKET

To install the optional wall storage bracket:

1. Use the bracket as a template to mark the location of the mounting holes at the area where the wall brackets will
be installed. Consider the dimensions of the chair when selecting and marking the location. The approximate
height of the bracket from the floor should be 60 inches.

2. Using fasteners (not supplied) appropriate for the wall type, install the bracket by using at least four of the
mounting holes.

3. Hang the chair from the bracket using the upper control handle.

English

Figure 35 - Storage Bracket Dimensions

Figure 36 - Chair stored on the bracket

Return To Table of Contents

www.stryker.com 6254 -109- 005 REV A 1-25

English

Operation Guide

INSTALLING THE OPTIONAL CABINET

To install the optional cabinet:

1. Use the bracket as a template to mark the location of the mounting holes at the area where the cabinet will be
installed. Consider the dimensions of the cabinet when selecting and marking the location. The approximate
height of the bottom of the cabinet to the floor should be at least 12 inches.

2. Using fasteners (not supplied) appropriate for the wall type, install the cabinet by using at least four of the
mounting holes.

3. Hang the chair from the bracket using the upper control handle.

Figure 37 - Cabinet Dimensions

Figure 38 - Chair stored in the cabinet

Return To Table of Contents

1-26 6254-109-005 REV A www.stryker.com

Operation Guide

INSTALLING THE OPTIONAL COVER

Note: It is easiest to install the cover when the chair is hanging.

To install the optional vinyl cover:

1. Slip the bottom pocket over the wheels.

2. Wrap the side flaps around the chair frame.

3. Pull the top flat down between the bars of the upper control handle and over the head support strap.

4. Attach the Velcro® strips.

5. Attach the red handle strip to the Velcro® on the front of the cover.

REMOVING THE OPTIONAL COVER

To remove the optional vinyl cover:

1. Pull the red handle strip.

2. Allow the cover to drop off the chair.

English

Figure 39: Slip the bottom pocket over the wheels Figure 40: Cover fully installed on the chair

Return To Table of Contents

www.stryker.com 6254 -109- 005 REV A 1-27

English

Cleaning

The Model 6254 Stryker Evacuation Chairs are designed to be power-washable. The unit may show some signs of
oxidation or discoloration from continuous washing, however, no degradation of the chair’s performance characteristics
or functionality will occur due to power washing as long as the proper procedures are followed.

WASHING PROCEDURE

• Follow the cleaning solution manufacturer’s dilution recommendations exactly.

• The preferred method Stryker Medical recommends for power washing stair chairs is with the standard hospital

surgical cart washer or hand held wand unit.

WASHING LIMITATIONS

WARNING

Use any appropriate personal safety equipment (goggles, respirator, etc.) to avoid the risk of inhaling contagion. Use of
power washing equipment can aerate contamination collected during the use of the chair.

CAUTION

• DO NOT STEAM CLEAN OR ULTRASONICALLY CLEAN THE UNIT.

• Maximum water temperature should not exceed 1800F/820C. Allow to air dry.

• Maximum water pressure should not exceed 1500 psi/130.5 bar. If a hand held wand is being used to wash the

unit, the pressure nozzle must be kept a minimum of 24 inches/61 centimeters from the unit.

• Failure to comply with these instructions may invalidate any and or all warranties.

If a foreign material gets between the Stair-TREAD™ system belt and track frame, the track frame must be cleaned.

1. Loosen the track belts and remove the rear wheels (see page 1-36 for instructions).

2. Clean the track frame completely with rubbing alcohol.

3. Use water at high pressure (see above) to rinse the belts. Be sure to clean both the inside and outside belt
surfaces.

4. Allow the belts to completely dry before reassembly.

5. Reassemble the track belts and the rear wheels (see page 1-36 for instructions).

6. Following the appropriate cautions and warnings, test the performance of the chair using a simulated passenger
weight while descending a flight of stairs.

7. If performance does not return to the original condition, the belts may need to be reconditioned or replaced.

Return To Table of Contents

1-28 6254-109-005 REV A www.stryker.com