Strong SRT 6200, SRT 6205 User Manual
Digital Satellite Receiver
SRT 6200/SRT 6202/SRT 6205
User Manual
Bedienungsanleitung
Manuel d'Utilisateur
Istruzioni d’uso
Manual del usuario
Felhasználói kézikönyv
Uputstvo za upotrebu
Руководство пользователя
1.00
SRT 6202/6205 SRT 6205
Picture similar
PART 1 • English
TABLE OF CONTENTS
1.0 INTRODUCTION 2
1.1 Safety Instructions 2
1.2 Storage 2
1.3 Equipment Set-up 3
1.4 Accessories 3
1.5 Usage of external USB devices 3
2.0 YOUR RECEIVER 3
2.1 Rear Panel 3
2.2 Remote Control Unit 4
2.3 Default PIN code: 0000 5
3.0 CONNECTIONS 5
3.1 Basic connection with SCART cable 5
3.2 Connecting to Satellite Dish 5
3.3 Connecting USB device 5
4.0 STARTING UP 5
4.1 Language Selection 5
4.2 Select Satellite 5
4.3 Antenna mode 6
5.0 MAIN MENU 6
5.1 Channel Organiser 6
5.2 Installation 7
5.3 System setting 8
6.0 WATCHING TV AND LISTENING TO THE RADIO 11
A.1 TROUBLE SHOOTING 13
A.2 SPECIFICATIONS 14
English
STRONG declares that this item complies with the basic
requirements and other relevant regulations of directives
CE 2004/108/EEC and 73/23EEC; RoHS 2002/95EEC
Subject to alterations. In consequence of continuous research
and development technical specifications, design and appearance
of products may change. All product names are trademarks or
registered trademarks of their respective owners.
© STRONG 2010. All rights reserved. 07/2013
1
PART 1 • English
1.0 INTRODUCTION
1.1 Safety Instructions
DO NOT INSTALL YOUR RECEIVER:
nIn a closed or poorly ventilated cabinet; directly on top of or under any other equipment;
on a surface which might obstruct the ventilation slots.
DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES:
nTo direct sunlight or near any other equipment that generates heat; to rain or intense
moisture; to intense vibration and to any shock which may cause permanent damage to
your receiver or to any magnetic objects, such as loudspeakers, transformers, etc.
nDo not use a damaged power cord. It may cause a fire or an electrical shock. Do not
touch a power cord with wet hands. It may cause an electric shock.
nWhen the receiver is not used for a long period of time, you should unplug the power
cord from the wall socket.
nDo not use alcohol or ammonia based liquids to clean the receiver. If you wish, you
may clean your receiver with a soft lint-free cloth slightly made damp with a mild soap
solution, only after disconnecting from the mains voltage supply. Make sure no foreign
objects fall through the ventilation slots because this could cause fire or an electric shock.
nDo not place any objects on top of the receiver because this might prevent proper cooling
of the components inside.
SAFETY PRECAUTIONS
nNever open the receiver cover. It is dangerous to touch the inside of the receiver due to
high voltage currents and possible electrical hazards and your warranty will be void. Refer
all maintenance or servicing to suitably qualified personnel.
nWhen you are connecting cables, be sure that the receiver is disconnected from the
mains supply voltage. Wait a few seconds after switching off the receiver before you move
the receiver or disconnect any equipment.
nIt is a necessity that you only use an approved extension and compatible wiring that
is suitable for the electrical power consumption of the installed equipment. Please
ensure that the electrical power supply corresponds with the voltage on the electrical
identification plate at the back of the receiver.
If the receiver does not operate normally even after strictly following the instructions in this user
manual, it is recommended to consult your dealer.
1.2 Storage
Your receiver and its accessories are stored and delivered in a packaging designed to protect against
electric shocks and moisture. When unpacking it, make sure that all the parts are included and keep
the packaging away from children. For transporting the receiver from one place to another or if you
are returning it under warranty conditions, make sure to repack the receiver in its original packaging
with its accessories. Failing to comply with such packaging procedures could void your warranty.
2
PART 1 • English
1.3 Equipment Set-up
We recommend you consult a professional installer to set up your equipment. Otherwise, please
follow the instructions below:
nRefer to the user manual of your TV and your antenna.
nMake sure that the SCART cable and outdoor components are in a good condition and
the SCART connections are well shielded
This manual provides complete instructions for installing and using this receiver. The following
symbols will serve as follow.
WARNING: Indicates warning information.
Tips: Indicates any other additional important or helpful information.
MENU Represents a button on the remote control or the receiver (Bold Character)
Move to Represents a menu item within a window. (Italic Character)
1.4 Accessories
nUser’s Manual
n1 Remote control unit
n2x Batteries (AAA type)
Note: The batteries should not be recharged, disassembled, electrically short-circuited,
be mixed or used with other types of batteries.
1.5 Usage of external USB devices
nIt is recommended to use USB 2.0 storage devices. If your device is not compatible
to USB 2.0 specifications, recording, playback and other multimedia functions of the
receiver would not work properly.
nTo ensure best performance of your USB storage device please format it by this receiver
(menu “Recording Device”) to FAT32 system. Other file systems are not supported by the
receiver.
nSTRONG cannot guarantee compatibility to all types of USB storage devices.
nIt is advised not to store important information on USB storage devices used with the
receiver. Always make backups of data on USB storage device before usage with receiver.
STRONG will not take responsibility for any loss of information or circumstances caused
by loss of information.
English
2.0 YOUR RECEIVER
2.1 Rear Panel
1. TO TV To connect to your TV using a coaxial cable or if you have a cable
connected to the ANT input from your TV*
2. ANT IN To connect to your terrestrial antenna or cable TV using coaxial cable*
3. SAT OUT To connect an extra receiver to the satellite signal from dish
4. SAT IN To connect to the LNB for satellite signal from dish
Fig. 2
3
Loading...