Note: picture not contractual
UM2420
User manual
SPC58XCADPT292S Rev. A evaluation board
Introduction
The SPC58XCADPT292S Rev.A evaluation board supports STMicroelectronics SPC58xCxxC3, microcontrollers in LFBGA292
package.
Figure 1. SPC58XCADPT292S Rev.A
UM2420 - Rev 2 - September 2020
For further information contact your local STMicroelectronics sales office.
www.st.com
1 Overview
The SPC58XCADPT292S mini module is an evaluation board supporting STMicroelectronics SPC58xCxxC3,
microcontrollers in LFBGA292 package.
The mini module is designed to be connected onto the SPC58XXMB motherboard, offering a mechanism for easy
customer evaluation of the supported microcontrollers, and to facilitate hardware and software development.
The mini module may be used as a stand-alone unit and allows access to the CPU, but no access to the I/O pins
as any motherboard peripherals.
UM2420
Overview
Figure 2. Overview of SPC58XCADPT292S Rev. A mini module - top
UM2420 - Rev 2
page 2/23
Figure 3. Overview of SPC58XCADPT292S Rev. A mini module - bottom
UM2420
Package contents
1.1 Package contents
An SPC58XCADPT292S adapter package includes the following item:
• SPC58XCADPT292S mini module
1.2 Supported devices
The SPC58XCADPT292S mini module supports the following STMicroelectronics family of microcontrollers in
LFBGA292 package:
• SPC58xCxxC3
UM2420 - Rev 2
page 3/23
UM2420
License agreement
2 License agreement
The packaging of this evaluation board was sealed with a seal stating, " by breaking this seal, you agree to the
terms and conditions of the evaluation board license agreement, the terms and conditions of which are available
at www.st.com/ebla ". Upon breaking the seal, you and STMicroelectronics entered into the evaluation board
license agreement, a copy of which is also enclosed with the evaluation board for convenience.
Attention: This evaluation board only offers limited features for evaluating ST products. It has not been tested for use with
other products and is not suitable for any safety or other commercial or consumer application. This evaluation
board is otherwise provided “AS IS” and STMicroelectronics disclaims all warranties, express or implied,
including the implied warranties of merchantability and fitness for a particular purpose.
UM2420 - Rev 2
page 4/23
3 Handling precautions
Please take care to handle the package contents in a manner such as to prevent electrostatic discharge.
Before the EVB is used or power is applied, please fully read the following sections on how to correctly configure
the board. Failure to correctly configure the board may cause irreparable component, MCU or EVB damage.
UM2420
Handling precautions
UM2420 - Rev 2
page 5/23
4 Hardware description
4.1 Hardware features
The SPC58XCADPT292S mini module board has the following features:
• Connector for external power supplies input (5.0V, 3.3V, 1.25V) used in stand-alone mode
• Reset button with driver and led indicator
• Socket for device in LFBGA292 package
• Debug ports: 38-pin TYCO connector for Nexus 2, 14-pin header connector for JTAG port and 12-pin header
connector for LFAST interface
• 40 Mhz crystal main oscillator with jumpers to optionally disconnect it
• 8 Mhz oscillator with jumpers to optionally disconnect it
• Clock input through SMA connector to optionally disconnect it
• Jumper for boot configuration
• 2 X SAMTEC QSH series, 240 way connector to connect mini module to Motherboard
4.2 Hardware dimension and PCB component view
UM2420
Hardware description
The mini module has the following dimensions:
• PCB area: 127 mm x 114.3 mm
• Top components height: 19.4 mm max
• Bottom components height: 3.5 mm max
• PCB thickness: 1.6 mm
UM2420 - Rev 2
page 6/23
5 Power and system configuration
5.1 Power supplies
When the mini module is plugged onto the motherboard, power is supplied directly by the motherboard. In this
setup, the external power supply input available on the mini module should NOT be used.
When the SPC58XCADPT292S mini module is used as a stand-alone board, external power supplies must be
used (5.0V, 3.3V, 1.25V).
The following jumpers are used to configure the power supply:
Table 1. Power configuration jumpers
Jumper Description Default Position
VDD_HV_ADR voltage configuration
J1
from 5.0V_LR or 3.3V_SR
VDD_HV_ADV voltage configuration
J2
from 5.0V_LR or 3.3V_SR
VDD_HV_JTAG_OSC voltage
configuration from 5.0V_SR
J3
or 3.3V_SR
VDD_HV_PMC voltage configuration
J4
from 5.0V_SR or 3.3V_SR
VDD_HV_IO_MAIN voltage
J6
configuration from 5.0V_SR or 3.3V_SR
VDD_HV_IO_FLEX voltage
J32
configuration from 5.0V_SR or 3.3V_SR
VDD_LV voltage configuration from
BALLAST circuit, 1.25V_SR or
J35
SMPS_REGULATOR_OUT
Supply for BALLAST circuit configuration
from VDD_HV_IO_MAIN or
J38
5.0V_SR
2-3 (1.25V_SR)
(VDD_HV_IO_MAIN)
1-2 (5.0V_LR)
1-2 (5.0V_LR)
1-2 (5.0V_SR)
1-2 (5.0V_SR)
1-2 (5.0V_SR)
1-2 (5.0V_SR)
1-2
UM2420
Power and system configuration
Figure 4. SPC58XCADPT292S Rev A top
component view - B2
Figure 4. SPC58XCADPT292S Rev A top
component view - B2
Figure 4. SPC58XCADPT292S Rev A top
component view - B2
Figure 4. SPC58XCADPT292S Rev A top
component view - B2
Figure 4. SPC58XCADPT292S Rev A top
component view - B2
Figure 4. SPC58XCADPT292S Rev A top
component view - C2
Figure 4. SPC58XCADPT292S Rev A top
component view - C4
Figure 4. SPC58XCADPT292S Rev A top
component view - D4
5.2 Microcontrollers configuration
Table 2. Microcontroller SPC58xCxxC3 configuration related jumpers
Jumper Description Default Position
Close (connect BCTRL with
BALLAST circuit) NOTE: the other
configuration is reserved
2-3: PORST(Default)
UM2420 - Rev 2
Device ball N19 BCTRL
J34
function configuration
Source reset
JP1
configuration
The jumpers are default closed for STMicroelectronics microcontroller SPC58xCxxC3:
• J34: default close
• JP1: default close 2-3
1-2: ESR0
Figure 4. SPC58XCADPT292S Rev A top
component view - C3
Figure 4. SPC58XCADPT292S Rev A top
component view - C3
page 7/23
5.3 Port configuration
The following jumpers need to configure the ports:
Jumper Description Default Position
J30 TESTMODE settings Close Figure 4. SPC58XCADPT292S Rev A top component view - C2
PK[10]/EVTI connection to QSH
J11
motherboard connectors
PJ[3]/EVTO connection to QSH
J31
motherboard connectors
PE[3]/CLKOUT connection to QSH
J40
motherboard connectors
PC[1]/ESR0 connection to QSH
J41
motherboard connectors
PA[14]/RDY connection to QSH
J42
motherboard connectors
PJ[8]/MCKO connection to QSH
J43
motherboard connectors
PL[9]/MSEO0 connection to QSH
J44
motherboard connectors
PL[11]/MSEO1 connection to QSH
J45
motherboard connectors
UM2420
Port configuration
Table 3. Ports related jumpers
Close Figure 4. SPC58XCADPT292S Rev A top component view - C3
Close Figure 4. SPC58XCADPT292S Rev A top component view - C3
Close Figure 4. SPC58XCADPT292S Rev A top component view - B4
Close Figure 4. SPC58XCADPT292S Rev A top component view - B3
Close Figure 4. SPC58XCADPT292S Rev A top component view - B3
Close Figure 4. SPC58XCADPT292S Rev A top component view - C1
Close Figure 4. SPC58XCADPT292S Rev A top component view - C2
Close Figure 4. SPC58XCADPT292S Rev A top component view - C2
5.4 System clock configuration
The mini module supports the usage of crystal clock sources as well as external clock source:
Table 4. Clock configuration jumpers
Jumper Description Default Position
40 MHz crystal clock source Enable
J21
for pin XTAL
Enable 8 MHz oscillator power
J22
supply
40 MHz crystal clock source Enable
J23
for pin XTAL
External clock source from 8 MHz
J24
oscillator or SMA connector
1-2 (XT1 pin)
Open
1-2 (XT1 pin1)
1-2 (8 MHz
oscillator)
Figure 4. SPC58XCADPT292S Rev A top component
view - C3
Figure 4. SPC58XCADPT292S Rev A top component
view - D3
Figure 4. SPC58XCADPT292S Rev A top component
view - C3
Figure 4. SPC58XCADPT292S Rev A top component
view - D3
UM2420 - Rev 2
page 8/23
5.5 Reset circuit
The mini module supports different ways to reset the microcontroller.
To use and perform the reset driving there are different jumpers and switches:
Jumper Description Default Position
SW1 Reset push button Open Figure 4. SPC58XCADPT292S Rev A top component view - D1
Connect the external reset to the reset
J27
driver for
ESR0 and PORST pins
J25 Connect the external reset to ESR0 pin Close Figure 4. SPC58XCADPT292S Rev A top component view - D2
J26 Connect the external reset to PORST pin Close Figure 4. SPC58XCADPT292S Rev A top component view - D2
5.6 Test points
The mini module has several test points. Below all test points description:
UM2420
Reset circuit
Table 5. Reset configuration jumpers
Close Figure 4. SPC58XCADPT292S Rev A top component view - D1
Table 6. Test points
Test point Description Position
TP3 JCOMP/RXN test point Figure 4. SPC58XCADPT292S Rev A top component view - C2
TP4 TCK test point Figure 4. SPC58XCADPT292S Rev A top component view - C2
TP5 TMS/TXP test point Figure 4. SPC58XCADPT292S Rev A top component view - C2
TP6 TDI/TXN test point Figure 4. SPC58XCADPT292S Rev A top component view - C2
TP7 TDO/RXP test point Figure 4. SPC58XCADPT292S Rev A top component view - C2
TP22 J16A, QSH connector, pin10 (PA5) test point Figure 4. SPC58XCADPT292S Rev A top component view - A4
TP28 J16A, QSH connector, pin11 (PA6) test point Figure 4. SPC58XCADPT292S Rev A top component view - A4
TP25 J16A, QSH connector, pin12 (PA7) test point Figure 4. SPC58XCADPT292S Rev A top component view - B4
TP26 J16A, QSH connector, pin13 (PA8) test point Figure 4. SPC58XCADPT292S Rev A top component view - B4
TP23 J16A, QSH connector, pin14 (PA9) test point Figure 4. SPC58XCADPT292S Rev A top component view - B4
UM2420 - Rev 2
page 9/23
5.7 Connectors
The mini module has the following connectors:
Connectors Description Position
J20
J18 14-pin header connector for JTAG port Figure 4. SPC58XCADPT292S Rev A top component view - A3
J39 38-pin TYCO connector for Nexus interface Figure 4. SPC58XCADPT292S Rev A top component view - B4
J36, J37 DC-DC Regulator Module Figure 4. SPC58XCADPT292S Rev A top component view - A1/A2
J16, J17
J5
P1 SMA Connector for External Clock Input Figure 4. SPC58XCADPT292S Rev A top component view - D3
12-pin header connector for LFAST
interface
2 X SAMTEC QSH series, 240 way
connector to connect mini module to
Motherboard
External power supplies input (5V, 3.3V,
1.25V)
UM2420
Connectors
Table 7. Connectors
Figure 4. SPC58XCADPT292S Rev A top component view - C2
Figure 5. SPC58XCADPT292S Rev A bottom component view
Figure 4. SPC58XCADPT292S Rev A top component view - D4
UM2420 - Rev 2
page 10/23
6 Layout overview
1
2
3
4
A
B
C
D
UM2420
Layout overview
Figure 4. SPC58XCADPT292S Rev A top component view
UM2420 - Rev 2
page 11/23
Figure 5. SPC58XCADPT292S Rev A bottom component view
1
2
3
4
A
B
C
D
UM2420
Layout overview
UM2420 - Rev 2
page 12/23
7 BOM
Qty Designator Part number EI Comment Part description
2 J16, J17 SAM-QSH12001LDA
1 J18 M.14.180 LP-3M N2514-6002RB
1 J20
2 J36, J37 STRIP36PMD STRIP Male Strip 36 pins pitch 2.54 180°
1 J39 TYCO-5767054-1 5767054-1 Conn Female 38 Pin, 180°, MICTOR - GND
1 J46 STRIP 2 mm
1 P1 BNC-SMA-FEM-180 CON 1 SMA Female RFSMA 180°
1 Q1 TRNJD2873-SMD NJD2873 NPN PlasticPower Transistor DPAK
4 R1, R2, R7 R26 RESMD000-0603 0R Resistor 1/10W 1% 0603
1 R3 10K Resistor 1/10W 1% 0603 - Do not mount
2 R4, R9 RESMD103-0603 10K Resistor 1/10W 1% 0603
2 R5, R6 0R Resistor 1/10W 1% 0603 - Do not mount
1 R8 RESMD101-0603 100R Resistor 1/10W 1% 0603
2 R10, R12 RESMD561-0603 560R Resistor 1/10W 1% 0603
3 R11, R13, R14 RESMD472-0603 4K7 Resistor 1/10W 1% 0603
1 R25 DNM Resistor 1/10W 1% 0805 - Do not mount
2 R27, R28 RESMD103-0603 10K Resistor
3 R29, R32, R33 DNM Resistor not mounted
4
1 SW1 PULSANTECS Pushbutt on Pushbutton NO
2 TP1,TP2 TEST1-SMD Testpoint SMD PCBtest point
10
TP23, TP25, TP26,
1 U1 ZOCC292OTB Socket
1 U2 Q8MHZ-SMD-3953M 8 MHz Hybrid QuartzOsc ECS 3953M
1 U3 74LVC125AMTR- SMD 74LVC12 5AMTR I.C.Low Voltage CMOS quad bus buffers - SO14
1 U5 74V1G08-SMD 74V1G08STR I.C.Single 2 - Input and gate - SMD SOT23-5L
1 Y1 Q40MHZ-SMD-5032 40MHZ Quartz 40 MHz NX5032GA XTAL NDK
R30, R31, R34,
R35
TP3, TP4, TP5,
TP6, TP7, TP22,
TP28
Table 8. BOM
Samtec QSH-120-01-
L-D-A
CONNERF805X2-
SMD
RESMD000-0603 0R Resistor
ERF8-005-05.0-L- DV-
L-TR
TEST POINT Testpoint SMD - Ignore
Samtec 0.5 mm pitch high speed socket
3MConn Flat Male 14 pins, straight - Pitch 2.54
mm
Samtec 0.8 mm pitch Rugged High Speed
Female Connector
Male Strip 20 poles, single row, vertical, golden,
pitch 2 mm - Do not mount
Socketfor BGA292 - OTB-292(484RS)-0.8-002
ENPLAS
UM2420
BOM
UM2420 - Rev 2
page 13/23
UM2420 - Rev 2
8 Schematics
Figure 6. Schematic of microcontroller power pins
page 14/23
Schematics
UM2420
PJ7
PJ5
PK[0..15](pg5)
PM[0..15](pg5)
PE[0..15](pg5)
PG[0..15](pg5)
PI[0..15](pg5)
PC[0..15](pg5)
PK2
PA12
PI7
PI2
PM4
PE1
PC5
PA3
CLKOUT
PI9
PA1
PC15
PE10
PM2
PM6
PE15
PI13
PI3
ESR0
PI14
PG3
PK13
PA0
PC6
PE0
PG1
PE8
PI10
PK7
PK15
PM8
PE2
PE14
RDY
PE4
PM10
PC12
PA2
PI6
PC8
PG11
PI11
PE7
PI15
PE5
PC2
PE12
PM9
PE11
PC0
PG2
PC14
PG12
PI12
J30
STRIP 2mm
12
PM1
PM7
EVTI
PK6
PI1
PA13
PC9
PG6
PK8
PG10
PA11
PC10
PC7
PG9
PE6
PC4
PG14
PK1
PC13
PK4
PK5
PK14
PE13
PA15
PI5
PK9
PM3
PK3
PK11
PE9
PG8
PM5
PG15
PA10
PG5
PG0
PI8
PK0
PK12
PC11
PG4
PM0
PI4
PC3
PG13
PG7
PI0
PA4
differential signals
PB6
PB5
PB4
PB3
PB2
PB1
PB0
PB14
PB13
PB12
PB11
PB10
PB9
PB8
PB7
PB15
PD5
PD4
PD3
PD2
PD1
PD0
PD14
PD13
PD12
PD11
PD10
PD9
PD8
PD15
PL9 (pg5)
PL9
J44
STRIP 2mm
1 2
MSEO0
MSEO0 (pg6)
PF6
PF5
PF4
PF3
PF2
PF1
PF0
PF14
PF12
PF11
PF10
PF9
PF8
PF7
PF15
PH6
PH5
PH4
PH3
PH2
PH1
PH0
PH14
PH13
PH12
PH11
PH10
PH9
PH8
PH7
PH15
PJ6
PJ4
EVTO
PJ2
PJ1
PJ0
PJ14
PJ13
PJ12
PJ11
PJ10
PJ9
MCKO
PJ15
PL11(pg5)
MSEO1 PL11
J45
STRIP 2mm
1 2
MSEO1 (pg6)
PL6
PL5
PL4
PL3
PL2
PL1
PL0
PL14
PL12
PL10
PL7
XTAL
PORST
EXTAL
EVTI(pg6)
PK10
J11
STRIP 2mm
12
PK10(pg5)
EVTI
PM14
MSEO0
MSEO1
PL8
PL13
PM12
PC1(pg5)
PC1
J41
STRIP 2mm
12
ESR0
ESR0
PN1
PN6
PN5
PN4
PN3
PN2
PN[0..6] (pg5)
TP5TP4 TP7TP6TP3
TDO/RXP
TCK
TDI/TXN
TMS/TXP
JCOMP/RXN
TMS/TXP(pg6)
TCK(pg6)
JCOMP/RXN(pg6)
TDO/RXP(pg6)
TDI/TXN(pg6)
PB[0..15] (pg5)
PF[0..15] (pg5,6)
PD[0..15] (pg5)
PH[0..15] (pg5)
PL[0..15] (pg5)
PJ[0..15] (pg5)
PORST(pg6,7)
XTAL(pg7)
EXTAL(pg7)
PA14
RDY
PA14(pg5)
RDY
J42
STRIP 2mm
12
PM11
SPC5XX 292BGA
SIGNALS
U1B
SOCKET
PH[13]
A3
PF[2]
A4
PF[5]
A5
PM[10]
A6
PH[15]
A7
PC[11]
A8
PC[13]
A9
PE[12]
A10
PD[0]
A11
PD[2]
A12
PH[9]
A13
PH[3]
A14
PA[11]
A15
PM[9]
A16
PA[0]
A17
PA[1]
A18
PD[14]
B1
PH[12]
B4
PF[3]
B5
PH[14]
B6
PF[4]
B7
PC[10]
B8
PC[12]
B9
PC[15]
B10
PD[1]
B11
PD[3]
B12
PH[4]
B13
PE[10]
B14
PE[11]
B15
PA[10]
B16
PA[13]
B17
PA[2]
B20
PC[9]
C1
PD[15]
C2
PA[12]
C19
PE[9]
C20
PC[7]
D1
PC[8]
D2
PM[2]
D6
PM[0]
D7
PK[14]
D8
PC[14]
D9
PM[6]
D10
PH[7]
D11
PH[8]
D12
PH[10]
D13
PH[1]
D14
PH[0]
D15
PD[5]
D19
PE[8]
D20
PB[7]
Y2
PB[6]
Y3
PG[12]
Y8
PE[13]
Y9
PI[12]
Y10
PI[10]
Y11
PF[0]
Y12
PD[10]
Y13
PB[10]
Y14
PB[8]
Y15
PD[8]
Y16
PF[6]
Y17
PJ[0]
Y18
PJ[1]
Y19
PG[5]
W1
PG[6]
W2
PI[6]
W3
PI[7]
W4
PG[8]
W5
PG[9]
W6
PG[11]
W7
PE[15]
W8
PB[2]
W9
PI[13]
W10
PI[11]
W11
PF[1]
W12
PD[9]
W13
PB[11]
W14
PB[9]
W15
PA[3]
W16
PF[7]
W17
PA[15]
W18
PI[4]
V1
PI[5]
V2
PJ[2]
V20
PI[3]
U2
PG[7]
U5
PK[11]
U6
PK[10]
U7
PE[14]
U8
PB[3]
U9
PB[1]
U10
PL[9]/MSEO0
U11
PL[11]/MSEO1
U12
PL[13]
U13
PL[15]
U14
PJ[7]/C LKN
U15
PJ[5]/C LKP
U16
PF[8]
U19
PJ[3]
U20
PI[2]
U1
PK[7]
T4
PK[8]
T5
PK[9]
T6
PG[10]
T7
PB[4]
T8
PD[11]
T9
PB[0]
T10
NC/PL[8]
A1
PL[10]
T12
PL[12]
T13
PL[14]
T14
PJ[6]
T15
PH[6]
T17
PJ[4]
T19
PH[5]
T20
PI[0]
R1
PB[5]
R2
PF[11]
R20
PK[4]
R4
PK[6]
R5
PJ[8]
R16
PJ[9]
R17
PF[12]
R19
PC[5]
E1
PC[6]
E2
PL[1]
E4
PM[3]
E6
PM[1]
E7
PK[15]
E8
PM[4]
E9
PM[5]
E10
PM[7]
E11
PM[8]
E12
PH[2]
E13
PG[15]
E14
PE[6]
E17
PE[7]
E19
PD[4]
E20
PC[3]
F1
PC[4]
F2
PE[5]
F20
PL[2]
F4
PL[0]
F5
PM[14]
F16
PG[13]
F17
PG[14]
F19
PC[2]
G1
PC[1]
G2
PL[3]
G4
PL[4]
G5
LPBK_N
G10
LPBK_P
G11
PA[4]/ESR1
G16
PORST
G17
PH[11]
G19
PF[15]
G20
PB[15]
P1
PB[13]
P2
PI[1]
P4
PK[5]
P5
PN[1]
P10
PN[2]
P11
PJ[10]
P16
PJ[11]
P17
PF[10]
P19
PF[9]
P20
PC[0]
H1
PE[0]
H2
PF[14]
H20
PL[6]
H4
PL[5]
H5
PA[9]/TDO
H16
PA[8]/TDI
H17
TESTMODE
H19
PE[1]
J1
PE[2]
J2
PD[12]
J4
PL[7]
J5
PA[6]/TCK
J16
PI[15]
J17
PD[7]
J19
PA[14]
J20
PD[13]
K1
PE[4]
K2
PE[3]
K4
PG[0]
K5
PN[3]
K7
PA[7]/TMS
K16
PI[14]
K17
PF[13]
K19
PD[6]
K20
PG[4]
N1
PG[3]
N2
PB[12]
N4
PB[14]
N5
PJ[13]
N16
PJ[12]
N17
PG[2]
M1
PG[1]
M2
PK[2]
M4
PK[3]
M5
PJ[15]
M16
PJ[14]
M17
XTAL
M19
EXTAL
M20
PI[8]
L1
PI[9]
L2
PK[0]
L4
PK[1]
L5
PN[4]
L7
PK[13]
L16
PK[12]
L17
PA[5]
L19
NC/PM[12]
Y1
NC/PM[11]
U4
PN[5]
H7
PN[6]
G8
PM[13]
T11
PM[15]
T1
PN[0]
T2
PN0
PM13
PM15
J43
STRIP 2mm
1 2
PJ8 (pg5)
PJ8
MCKO(pg6)
MCKO
GND
J31
STRIP 2mm
1 2
PJ3 (pg5)
PJ3
EVTO (pg6)
EVTO
PD6
PL15
PE3(pg5)
PE3
J40
STRIP 2mm
12
CLKOUT
CLKOUT
PA[0..15](pg5)
PD7
PF13
GND
MICROCONTROLLER PIN
Port pins and reset signals
are routed to motherboard.
High speed signals are not
routed to mother board, but have
test points to connect to test
on mother board connector
EVT signals are connected to optional
jumpers to be routed to mother board
UM2420 - Rev 2
Figure 7. Schematic of microcontroller IO & service pins
page 15/23
Schematics
UM2420
PL4
PL2
PL0
PL14
PL12
PL10
PL8
PL6
PJ6
PJ4
3.3V_SR
PJ2
PJ0
PH2
PH0
PJ14
PJ12
PJ10
PJ8
PH10
1.25V_SR
PH8
PH6
PH4
PF12
PF10
PF0
PH14
PH12
PF8
PF6
PF4
PF2
3.3V_SR
PF14
PD8
PD4
PD2
PD0
5.0V_SR
PB0
1.25V_SR
PD14
PD12
PD10
PB12
PB10
PB8
PB6
PB4
PB2
1.25V_SR
3.3V_SR
5.0V_SR
1.25V_SR
PB14
3.3V_SR
TP26
TP28 TP25
TP22
TP23
PA4
PD6 PD7
PF13
PL13
J16A
SAMTEC QSH-120-01-L-D-A
1
1
3
3
5
5
7
7
9
9
11
11
13
13
15
15
17
17
19
19
21
21
23
23
25
25
27
27
29
29
31
31
33
33
35
35
37
37
39
39
41
41
43
43
45
45
47
47
49
49
51
51
53
53
55
55
57
57
59
59
61
61
63
63
65
65
67
67
69
69
71
71
73
73
75
75
77
77
79
79
81
81
83
83
85
85
87
87
89
89
91
91
93
93
95
95
97
97
99
99
101
101
103
103
105
105
107
107
109
109
111
111
113
113
115
115
117
117
119
119
2
2
4
4
6
6
8
8
10
10
12
12
14
14
16
16
18
18
20
20
22
22
24
24
26
26
28
28
30
30
32
32
34
34
36
36
38
38
40
40
42
42
44
44
46
46
48
48
50
50
52
52
54
54
56
56
58
58
60
60
62
62
64
64
66
66
68
68
70
70
72
72
74
74
76
76
78
78
80
80
82
82
84
84
86
86
88
88
90
90
92
92
94
94
96
96
98
98
100
100
102
102
104
104
106
106
108
108
110
110
112
112
114
114
116
116
118
118
120
120
PL15
New connection
PM12
J16B
SAMTEC QSH-120-01-L-D-A
SH1
SH1
SH2
SH2
SH3
SH3
SH4
SH4
SH5
SH5
SH6
SH6
SH7
SH7
SH8
SH8
SH9
SH9
121
121
123
123
125
125
127
127
129
129
131
131
133
133
135
135
137
137
139
139
141
141
143
143
145
145
147
147
149
149
151
151
153
153
155
155
157
157
159
159
161
161
163
163
165
165
167
167
169
169
171
171
173
173
175
175
177
177
179
179
181
181
183
183
185
185
187
187
189
189
191
191
193
193
195
195
197
197
199
199
201
201
203
203
205
205
207
207
209
209
211
211
213
213
215
215
217
217
219
219
221
221
223
223
225
225
227
227
229
229
231
231
233
233
235
235
237
237
239
239
SH16
SH16
SH15
SH15
SH14
SH14
SH13
SH13
SH12
SH12
SH11
SH11
SH10
SH10
122
122
124
124
126
126
128
128
130
130
132
132
134
134
136
136
138
138
140
140
142
142
144
144
146
146
148
148
150
150
152
152
154
154
156
156
158
158
160
160
162
162
164
164
166
166
168
168
170
170
172
172
174
174
176
176
178
178
180
180
182
182
184
184
186
186
188
188
190
190
192
192
194
194
196
196
198
198
200
200
202
202
204
204
206
206
208
208
210
210
212
212
214
214
216
216
218
218
220
220
222
222
224
224
226
226
228
228
230
230
232
232
234
234
236
236
238
238
240
240
PE13
PE12
PortE
PM12
PE15
PE14
PF0
PF6
PF5
PF4
PF3
PF2
PF1
PF10
PF9
PF8
PF[0..15]
PF7
PF[0..15](pg4, 6)
PF14
PF12
PF11
PortF
PF15
PM14
PG1
PG0
PG7
PG6
PG5
PG4
PG3
PG2
PG[0..15](pg4)
PG10
PG9
PG8
PG[0..15]
PortG
PG14
PG13
PG12
PG11
PG15
PH2
PH1
PH0
PH[0..15]
PH7
PH6
PH5
PH4
PH3
PH12
PH11
PH10
PH9
PH8
J17A
SAMTEC QSH-120-01-L-D-A
1
1
3
3
5
5
7
7
9
9
11
11
13
13
15
15
17
17
19
19
21
21
23
23
25
25
27
27
29
29
31
31
33
33
35
35
37
37
39
39
41
41
43
43
45
45
47
47
49
49
51
51
53
53
55
55
57
57
59
59
61
61
63
63
65
65
67
67
69
69
71
71
73
73
75
75
77
77
79
79
81
81
83
83
85
85
87
87
89
89
91
91
93
93
95
95
97
97
99
99
101
101
103
103
105
105
107
107
109
109
111
111
113
113
115
115
117
117
119
119
2
2
4
4
6
6
8
8
10
10
12
12
14
14
16
16
18
18
20
20
22
22
24
24
26
26
28
28
30
30
32
32
34
34
36
36
38
38
40
40
42
42
44
44
46
46
48
48
50
50
52
52
54
54
56
56
58
58
60
60
62
62
64
64
66
66
68
68
70
70
72
72
74
74
76
76
78
78
80
80
82
82
84
84
86
86
88
88
90
90
92
92
94
94
96
96
98
98
100
100
102
102
104
104
106
106
108
108
110
110
112
112
114
114
116
116
118
118
120
120
PortH
PH[0..15](pg4)
PH15
PH14
PH13
PI3
PI2
PI1
PI0
PI8
PI[0..15]
PI7
PI6
PI5
PI4
PI[0..15](pg4)
PI11
PI10
PI9
PortI
3.3V_SR
5.0V_LR
1.25V_SR
PI15
PI14
PI13
PI12
1.25V_SR 3.3V_SR
5.0V_SR
VDD_HV_IO_MAIN5.0V_SR 5.0V_LR
VDD_HV_IO_MAIN
PC4
PC3
PC2
PC1
PC0
PC9
PC8
PC[0..15]
PC7
PC6
PC5
PC14
PC13
PC12
PC11
PC10
PC[0..15](pg4)
PC15
PortC
PJ0
PJ5
PJ4
PJ3
PJ2
PJ1
PJ10
PJ9
PJ8
PJ[0..15]
PJ6
PJ[0..15](pg4)
PJ13
PJ12
PJ11
PortJ
PJ15
PJ14
PK1
PK0
PK6
PK5
PK4
PK3
PK2
PK11
PK10
PK9
PK8
PK[0..15]
PK7
PK15
PK14
PK13
PK12
PortK
PK[0..15](pg4)
PL2
PL1
PL0
PL7
PL6
PL5
PL4
PL3
PL12
PL10
PL8
PL[0..15]
PL[0..15](pg4)
PL14
PortL
PJ7
PA3
PA2
PA1
PA0
PA[0..15](pg4)
PortA
PA10
PA[0..15]
J17B
SAMTEC QSH-120-01-L-D-A
SH1
SH1
SH2
SH2
SH3
SH3
SH4
SH4
SH5
SH5
SH6
SH6
SH7
SH7
SH8
SH8
SH9
SH9
121
121
123
123
125
125
127
127
129
129
131
131
133
133
135
135
137
137
139
139
141
141
143
143
145
145
147
147
149
149
151
151
153
153
155
155
157
157
159
159
161
161
163
163
165
165
167
167
169
169
171
171
173
173
175
175
177
177
179
179
181
181
183
183
185
185
187
187
189
189
191
191
193
193
195
195
197
197
199
199
201
201
203
203
205
205
207
207
209
209
211
211
213
213
215
215
217
217
219
219
221
221
223
223
225
225
227
227
229
229
231
231
233
233
235
235
237
237
239
239
SH16
SH16
SH15
SH15
SH14
SH14
SH13
SH13
SH12
SH12
SH11
SH11
SH10
SH10
122
122
124
124
126
126
128
128
130
130
132
132
134
134
136
136
138
138
140
140
142
142
144
144
146
146
148
148
150
150
152
152
154
154
156
156
158
158
160
160
162
162
164
164
166
166
168
168
170
170
172
172
174
174
176
176
178
178
180
180
182
182
184
184
186
186
188
188
190
190
192
192
194
194
196
196
198
198
200
200
202
202
204
204
206
206
208
208
210
210
212
212
214
214
216
216
218
218
220
220
222
222
224
224
226
226
228
228
230
230
232
232
234
234
236
236
238
238
240
240
PA15
PA13
PA12
PA11
PB4
PB3
PB2
PB1
PB0
PB[0..15](pg4)
PB7
PB6
PB5
PortB
PB11
PB10
PB9
PB8
PB[0..15]
PB15
PB14
PB13
PB12
PD0
PD5
PD4
PD3
PD2
PD1
PD[0..15](pg4)
PD8
PD[0..15]
PD13
PD12
PD11
PD10
PD9
PortD
PD15
PD14
PE1
PE0
PE6
PE5
PE4
PE3
PE2
PE10
PE9
PE8
PE[0..15]
PE7
PE[0..15](pg4)
PE11
RST-SW(pg7)
PL9
PL11
PL9
PL11
VDD_HV_IO_MAIN VDD_HV_IO_MAIN
GND
PA14
PJ5
PK7
PK5
PK1
PK15
PK13
PK3
PK11
PK9
PK0
PK10
PK8
PK6
PK4
PK2
PK14
PK12
PI4
PI2
PI12
PI10
PI8
PI0
PI6
PI14
PG0
PG2
PG14
PG12
PG10
PG8
PG6
PG4
5.0V_SR
PE6
PE4
PE2
PE14
PE12
PE10
PE0
PE8
1.25V_SR
PC2
PC0
PC12
PC10
PC8
PC6
5.0V_SR
PC4
3.3V_SR
PC14
PA12
PA10
PA4
PA2
PA0
1.25V_SR
PJ7
PM14
5.0V_SR
PD6
PI9
PI3
PI7
PI5
PI1
PI15
PI13
PI11
PA14
PB15
PG11
PG9
PG7
PG5
PG3
PG1
VDD_HV_IO_F LEX
3.3V_SR
1.25V_SR
3.3V_SR
5.0V_SR
1.25V_SR
5.0V_SR
PG15
PG13
VDD_HV_IO_F LEX
PD7
PE1
PL1
PL3
1.25V_SR
PE5
1.25V_SR
PE15
PE13
PE11
PJ3
PJ11
PJ9
PJ1
PL7
PL5
PE3
PE9
PE7
PH5
PH3
1.25V_SR
PJ15
PJ13
PM15
PH13
PH11
PH9
PH1
PH7
PF3
PF15
PF11
PF1
3.3V_SR
PH15
PC1
PD1
5.0V_SR
PF9
PF7
PF5
PC11
PC9
PC3
PC7
PC5
VDD_HV_IO_F LEX
PD13
PD11
PD9
PD5
PD3
3.3V_SR
PC15
PC13
PB7
PB5
PB3
PB1
3.3V_SR
PD15
VDD_HV_IO_F LEX
PB13
PB11
PB9
VDD_HV_IO_F LEX
PA1
PA3
1.25V_SR
5.0V_SR
PA15
PA13
PA11
PM13
PF13
1.25V_SR
3.3V_SR
5.0V_SR
1.25V_SR
5.0V_SR
3.3V_SR
1.25V_SR
1.25V_SR
5.0V_SR
PM1
PM5
PM3
5.0V_LR
GND
PM9
PM7
PM0
PM10
PM8
PM6
PM4
5.0V_LR
PM2
5.0V_LR 5.0V_LR
3.3V_SR
3.3V_SR
5.0V_SR
5.0V_SR
1.25V_SR
1.25V_SR
PM2
PM1
PM0
RST-SW
PM7
PM6
PM5
PM4
PM3
PM10
PM9
PM8
PM[0..15]
PM[0..15]
(pg4)
PortM
GND GND
PN6
PN5
PN3
PN4
PN2
PN1
PM13
PN1
PN0
PN6
PN5
PN4
PN3
PN2
PN[0..6]
PortN
PN[0..6](pg4)
PM15
PN0
5.0V_SR
1.25V_SR
1.25V_SR
5.0V_LR
VDD_HV_IO_MAIN
5.0V_LR
VDD_HV_IO_MAIN
3.3V_SR
3.3V_SR
5.0V_SR
VDD_HV_IO_MAINVDD_HV_IO_MAIN
5.0V_LR
3.3V_SR
5.0V_SR
5.0V_SR
1.25V_SR
1.25V_SR
VDD_HV_IO_MAIN
5.0V_LR
VDD_HV_IO_MAIN
3.3V_SR
PL13
PL15
3.3V_SR
3.3V_SR
5.0V_SR
5.0V_SR
PM11
1.25V_SR
1.25V_SR
PM11
DAUGHTER CARD TO MOTHERBOARD CONNECTOR
UM2420 - Rev 2
page 16/23
Figure 8. Schematic of daughter card to motherboard connector
Schematics
UM2420
LFAST interface
J37
STRIP
2
1
3
4
5
6
SMPS_REGULATOR_OUT
GND
PG15
ball E14
(smps_pmos0)
ball D14
(smps_nmos1)
ball D15
(smps_vlx)
PH1
GND
GND
MSEO1 (pg4)
MSEO1
TCK(pg6)
DRCLK
C132 DNM
C133 DNM
GND
MCKO(pg4)
RSTIN(pg6,7)
PF4
X7R
X7R
C134
27pF
50V
COG/NP0
0603
GND
R29 DNM
0603
RDY
100R
R30
0R
RSTIN(pg6,7)
RSTIN (pg6,7)
TDO/RXP(pg4)
TDO/RXP
TDO
R31
0R
TDI
TDI/TXN
TDI/TXN (pg4)
VDD_HV_IO_MAIN
R32
DNM
0603
R33
DNM
0603
VDD_HV_IO_MAIN
GND
CLKOUT
Nexus level 3+ support
JCOMP/RXN(pg4)
R34
0R
JCOMP
TMS/TXP(pg4)
R35
0R
TMS
J46
STRIP 2mm
DNP
12
ESR0(pg7)
JTAG interface
VDD_HV_IO_J TAG
TDO
EVTI
TDO(pg4,6)
TDI(pg4,6)
GND
TCK(pg4,6)
TCK
RSTIN
EVTI(pg4)
TMS
GND
JCOMP
TDI
(VSS)
(VSS)
JTAG Connecto r
Place CAPS as close t o
connector pins a s
possible but do NOT fi t
caps at board assembly .
JCOMP(pg4,6)
(VSS)
(VSS)
TMS(pg4,6)
TMS
JCOMP
EVTO(pg4)
VDD_HV_IO_J TAG
EVTO
J18
N2514-6002RB
1 2
3 4
65
7 8
9 10
11 12
13 14
C56
47pF
DNP
PORST(pg4,6,7)
C57
47pF
DNP
PORST
TDI, TDO, TCK, TMS & JCOMP are not connected to
daughter card.
PORST, ESR0, EVTI and EVTO are connected to daughtercard
RDY not implemented on SPC57xxmM
PORST
R3
10K
DNP
GND
R4
10K
Previson DC-DC Regulator
PF[0..15]
(pg5,6)
PH[0..15](pg4)
PG[0..15](pg4)
PM[0..15](pg5)
PJ[0..15](pg5)
PL[0..15](pg5)
PH[0..15](pg5)
PD[0..15](pg5)
GND
GND
J20
SAMTEC TFM-105-02-L-D-WT
1 2
3 4
5 6
7 8
9 10
1112
C135
27pF
PJ7
PH15
PJ6
PM10
PF5
PL12
PL13
PL15
PL14
PD3
PL10
J39
5767054-1
NC1
1
NC2
3
MDO09
5
VSTBY
37
ToolIO0
35
VBatt2
33
VBatt1
31
ToolIO1
29
TDET/WDTC
27
RSTOUT
25
MDO11
23
JCOMP
21
TDI
19
TMS
17
TCK
15
MDO10
13
TDO
11
RSTIN
9
BootCFG
7
NC3
2
NC4
4
CLKOUT
6
MSEO0
38
MSEO1
36
MCKO
34
EVTO
32
MDO0
30
MDO1
28
MDO2
26
MDO3
24
MDO4
22
MDO5
20
MDO6
18
MDO7
16
RDY
14
VTREF
12
EVTI
10
MDO08
8
GND139GND240GND341GND442GND5
43
TCK(pg4,6)
TDO(pg4,6)
ESR0(pg4,6,7)
JCOMP(pg4,6)
TDI(pg4, 6)
TMS(pg4,6)
R27 10K
DNP
GND
EVTI(pg4)
VDD_HV_IO_MAIN
VDD_HV_IO_MAIN
EVTO(pg4)
GND
R28 10K
MSEO0 (pg4)
MSEO0
PH0
VDD_HV_IO_MAIN
GND
JTAG, NEXUS & LFAST
J36
STRIP
2
1
3
4
5
6
UM2420 - Rev 2
Figure 9. Schematic of Jtag, nexus and lfast connectors
page 17/23
Schematics
UM2420
Clock and Reset Circuitry
VDD_HV_I O_MAIN
VDD_HV_I O_MAIN
Y1
40MHZ
1
2
External Oscill ator
R5
0R
DNP
External Clock Input
R6
0R
DNP
R7
0R
R8 100R
C58 100nF
R13
4K7
R9 10K R 10 560R
D1 Y ellow
VCC
GND
U3A
74LVC125AMTR
2 3
14
1
7
U3C
74LVC125AMTR
9 8
10
U3B
74LVC125AMTR
5 6
4
GND
PORST(pg4,6)
ESR0(pg4, 6)
RST-SW(pg5)
Reset Circuit
GND
J25
STRIP 2mm
1 2
MCU RESET LE D
GND
J26
STRIP 2mm
1 2
ESR0
PORST
J27
STRIP 2mm
1 2
VDD_HV_I O_MAIN
USR RESET LE D
VDD_HV_I O_MAIN
GND
GND
RST-SW
RST-MCU
Reset-In
Disable
R11
4K7
R12 560R
Note - External 3.3 V
regulator MUST be
enabled when using
oscillator module
GND
SMA style
Connector
J22
STRIP 2mm
1 2
EVB-EXTAL
OSC-MOD
GND
EXTAL-SMA
P1
1
2
4 3
5
J24
1
2
3
Note-Internal
Pull-Up on Pin1
3.3V_SR
XTAL
EXTAL
Loop Controlled Pierc e
Oscillator Circui t
J21
1
2
3
VSS_OSC
J23
1
2
3
GND
Connect XTAL jumper to GND when driving EXTAL from
Oscillator Module or External Source
(MCU Crystal Output)
(MCU Crystal Input)
EVB-EXTAL
REMOVE XTAL jumper when driving EXTAL from
Oscillator Module or External Source
CLK
OUT
VDD
GND
OE
U2
8MHz
4
2
31
R14
4K7
GND
VCC
U5
74V1G08STR
1
2
4
53
SW1
Pushbutton
D4
Red
EVB-EXTAL(pg7)
EXTAL(pg4)
EVB-EXTAL(pg7)
XTAL
(pg4)
UM2420 - Rev 2
Figure 10. Schematic of clock and reset circuit
page 18/23
Schematics
UM2420
Revision history
Date Version Changes
15-Nov-2018 1 Initial release.
10-Sep-2020 2
UM2420
Table 9. Document revision history
Updated the title in cover page.
Updated Section 1 Overview, Section 4 Hardware description and
Section 5 Power and system configuration.
Added Section 2 License agreement and Section 6 Layout overview.
Minor text changes.
UM2420 - Rev 2
page 19/23
UM2420
Contents
Contents
1 Overview ..........................................................................2
1.1 Package Contents..............................................................3
1.2 Supported Devices .............................................................3
2 License agreement ................................................................4
3 Handling precautions ..............................................................5
4 Hardware description ..............................................................6
4.1 Hardware features..............................................................6
4.2 Hardware dimension and PCB component view .....................................6
5 Power and system configuration...................................................7
5.1 Power supplies ................................................................7
5.2 Microcontrollers configuration ....................................................7
5.3 Port configuration ..............................................................8
5.4 System clock configuration ......................................................8
5.5 Reset circuit ...................................................................9
5.6 Test points ....................................................................9
5.7 Connectors...................................................................10
6 Layout overview ..................................................................11
7 BOM..............................................................................13
8 Schematics.......................................................................14
Revision history .......................................................................19
UM2420 - Rev 2
page 20/23
UM2420
List of tables
List of tables
Table 1. Power configuration jumpers ............................................................7
Table 2. Microcontroller SPC58xCxxC3 configuration related jumpers......................................7
Table 3. Ports related jumpers .................................................................8
Table 4. Clock configuration jumpers ............................................................8
Table 5. Reset configuration jumpers ............................................................9
Table 6. Test points ........................................................................9
Table 7. Connectors .......................................................................10
Table 8. BOM ...........................................................................13
Table 9. Document revision history ............................................................. 19
UM2420 - Rev 2
page 21/23
UM2420
List of figures
List of figures
Figure 1. SPC58XCADPT292S Rev.A...........................................................1
Figure 2. Overview of SPC58XCADPT292S Rev. A mini module - top .....................................2
Figure 3. Overview of SPC58XCADPT292S Rev. A mini module - bottom ..................................3
Figure 4. SPC58XCADPT292S Rev A top component view ........................................... 11
Figure 5. SPC58XCADPT292S Rev A bottom component view ........................................ 12
Figure 6. Schematic of microcontroller power pins ................................................. 14
Figure 7. Schematic of microcontroller IO & service pins ............................................. 15
Figure 8. Schematic of daughter card to motherboard connector ....................................... 16
Figure 9. Schematic of Jtag, nexus and lfast connectors .............................................17
Figure 10. Schematic of clock and reset circuit..................................................... 18
UM2420 - Rev 2
page 22/23
UM2420
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST
products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST
products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of
Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. For additional information about ST trademarks, please refer to www.st.com/trademarks. All other product or service
names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2020 STMicroelectronics – All rights reserved
UM2420 - Rev 2
page 23/23
Loading...