Stamina Products UX2 User Manual

Owner's Manual

W A RNING

Exercise can pre sent a health
risk. Consult a physician
before beginning a ny exercise
program with this equipment.
If you feel faint or dizzy,
immediately discontinue use
of this equipment. Serious
bodily injury can occur if this
equipment is not assembled
and used correctly. Serious
bodily injury can also occur if
all instructions are not
followed. Keep others and
pets away from equipment
when in use. Always make
sure all bolts and nuts are
tightened prior to each use.
Follow all safety instructions in
this manual.

CAUTION:
Weight on this product should not exceed 250 lbs.

This Product is Produced Exclusively by

2040 N. Alliance, Springfield, MO 65803

Customer Service Number

1 [phone]

2007, 06

www.stamin aproducts.com

When calling for parts or
service, please specify the
following number.

15-0960

STAMINA PRODUCTS

MADE IN CHINA

Product May Vary Slightly

From Pictured.

2007 Stamina Products, Inc.

TABLE OF CONTENTS

Page Page

Safety Precautions 2
Before You Begin 4
Hardware Illustrations 5
Assembly In structions 6
Set Up Instruction s 10
Operational Instructions 1 1
Storage 14

Adjustment Instruction s 15
Conditioning Guidelines 17
Warm-up and Cool-Down 18
Warranty 19
Product Parts Drawing 20
Parts List 21
Fax/Mail Ordering Form 23

Maintenance 14

SAFETY PRECAUTIONS

WARNING:

Read all warnings posted on the UX2 AIR BIKE.

1.
Read this owner's/user's manual and follow it carefully before using the UX2 AIR BIKE.

2.
We recommend that two people be available for assembly of this product.

3.
To avoid a pinch point, make sure that the spacer is properly assembled between the CRANK and LINKAGE

4.
CONNECTOR on both sides of the UX2 AIR BIKE. See assembly STEP 11.
Keep children away from the UX2 AIR BIKE. Do not allow children to use or play on the UX2 AIR BIKE. Keep

5.
children and pets away from the UX2 AIR BIKE when it is in use.
It is recommended that you place this exercise equipment on an equipment mat.

6.
Set up and operate the UX2 AIR BIKE on a solid level surface. Do not position the UX2 AIR BIKE on loose

7.
rugs or uneven surfaces.
Adjust the LEVELING CAPS on the FRONT STABILIZER so that the UX2 AIR BIKE sets on the floor without

8.
rocking.
Inspect the UX2 AIR BIKE for worn or loose components prior to use.

9.
Always check to see that the SEAT POST is securely fastened before using the UX2 AIR BIKE.

10.
Tighten/replace any loose or worn components prior to using the UX2 AIR BIKE.

11.
Consult a physician prior to commencing an exercise program. If, at any time during exercise, you feel faint,

12.
dizzy, or experience pain, stop and consult your physician .
Follow your physician's recommendations in developing your own personal fitness program.

13.
Always choose the workout which best fits your physical strength and flexibility level. Know your limits and

14.
train within them. Always use common sense when exercising.
Do not wear loose or dangling clothing while using the UX2 AIR BIKE.

15.
Never exercise in bare feet or socks; always wear correct f ootwear , such as running, walking, or crosstraining

16.
shoes. Be sure that they fit well, provide foot support and feature non-skid rubber soles.
Care should be taken in mounting or dismounting the UX2 AIR BIKE.

17.
The UX2 AIR BIKE should not be used by persons weighing over 250 pounds.

18.
Do not ride the UX2 AIR BIKE standing up.

19.
Do not place your head, hands, or legs between the HANDLEBARS.

20.
Each user should adjust the seat per instructions on page 12.

21.
The UX2 AIR BIKE should be used by only one person at a time.

22.
The UX2 AIR BIKE is for consumer use only. It is not for use in public or semipublic facilities.

23.

To reduce the risk of serious injury, read the following Safety Precautions before
using the UX2 AIR BIKE.

WARNING:

Before starting a ny exercise or conditioning progra m you should consult with your person al
physicia n to see if you require a complete physical exam. This is especially importa nt if you
are over the age of 35, have never exercised before, are pregnant, or suffer from any
illness. READ AND FOLLOW THE SAFETY PRECAUTIONS. FAILURE TO FOLLOW

THESE INSTRUCTIONS CAN RESUL T IN SERIOUS BODILY INJURY.

2

CALL US FIRST

THANK YOU FOR PURCHASING THE

STAMINA

To help you get started, we have pre-assembled most of your

UX2 AIR BIKE at the factory with the exception

of those few parts left unassembled for shipping purposes.

Simply follow the few assembly instructions set forth in this manual.

With regular workouts you will be getting your body into shape

and on your way to achieving a ha ppier and healthier lifestyle.

Should you have any questions,

please call our Customer Service Department toll-free number,

1 [phone]

Monday - Thursday, 7:30 A.M. - 5:00 P.M. Central Time.

Friday, 8:00 A.M. - 3:00 P.M., Central Time.

UX2 AIR BIKE

TELEPHONE

CUSTOMER SERVICE

Tel: [phone]

FAX

CUSTOMER SERVICE

Fax: [phone]

ONLINE

CUSTOMER SERVICE

[e-mail]

[e-mail]

www.staminaproducts.com

3

STAMINA PRODUCTS, INC.

MAIL

ATTN: Customer Service

P.O. Box 1071

Springfield, MO. 65801-1071

BEFORE YOU BEGIN

Thank you for choosing the UX2 AIR BIKE. We
take great pride in producing this quality product a nd
hope it will provide many hours of quality exercise to
make you feel better, look better and enjoy life to its
fullest.
Yes, it's a proven fact that a regular exercise
program can improve your physical and mental
health. Too often, our busy lifestyles limit our time
and opportunity to exercise. The UX2 AIR BIKE
provides a convenient and simple method to begin
your assault on getting your body in shape and
achieving a happier and healthier lifestyle.
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
Read this manual carefully before using the UX2

AIR BIKE.

Foam Grip

Although Stamin a constructs its products with the
finest materials and uses the highest standards of
manufacturing and quality control, there can
sometimes be missing parts or incorrectly sized
parts. If you have any questions or problems with
the parts included with your UX2 AIR BIKE, please
do not return the product. Contact us FIRST!
If a part is missing or defective, please call us toll
free at 1-800-375-7520 (in the U.S.). Our Customer
Service Staff is available to a ssist you from 7:30 A.M.
to 5:00 P .M. (Central T ime) Monday through Thursday
and 8:00 A.M. to 3:00 P.M. (Central T i me) on Friday.
If you would like to contact us on-line, go to our
website at www.sta min aproducts.com a nd a ccess the
Customer Service section.
Be sure to have the name and model number of
the product available when you conta ct us.

Monitor

Seat

Bellows

Main Fra me

Endcap

Rear Support

Left Handla bar

Tension Knob

Foam Grip

Right Handlebar
Meter Post

Fan Cage
Right Chain Guard

Lower Bar
Leveling Cap

Right Linkage
Pedal

Crank

THE FOLLOWING TOOLS ARE INCLUDED FOR ASSEMBLY :

4

Wrench
Multi-opening Wrench
Allen Wrench (6mm)

HARDWARE IDENTIFICATION CHART

This chart is provided to help identify the hardware used in the assembly process. Place the washers, the
end of the bolts, or screws on the circles to check for the corre ct di ameter. Use the small scale to check the
length of the bolts and screws.

3/16" 5/16" 1/2"3/8"1/4"

INCHES

11/2021/2 31/2 41/2 51/2 61/2

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

MILLIMETERS

6 8 10 12

NOTICE: The length of all bolts and screws except those with flat hea ds is

measured from below the head to the end of the bolt or screw.
Flat head bolts and screws are measured from the top of the
head to the end of the bolt or screw.

After unpacking the unit, open the hardware bag and make sure that you have all the following items.
Some hardware may be already attached to the part.

length

length

in.

mm.

Part No. and Description Qty

51 Carriage Bolt (M8 x 1.25 x 38mm) 2

53 Screw, Round He ad (M5 x 15mm) 1

57 Screw, Round Head (M5 x 0.8 x 12mm) 4

58 Screw, Flat Head (M5 x 0.8 x 15mm) 1

59 Bolt, Round Head (M6 x 1 x 12mm) 4

35 Thin Nut (1/2"-20) 2

61 Bolt, Hex Hea d (M8 x 1.25 x 45mm) 2

62 Nylock Nut (M8 x 1.25) 7

64 Acorn Nut (M8 x 1.25) 2

70 Arc Washer (M6) 4
71 Arc Washer (M8) 4

38 Bushing Washer (ø16.3 x ø25 x 0.5t) 2
39 Large Washer (M8) 2
67 Washer (M8 x ø16mm x 1.5mm) 3
68 Washer (M8 x ø22mm x 1.5mm) 2

5

ASSEMBLY INSTRUCTIONS

Place all parts from the box in a cleared area and position them on the floor in front of you. Remove all
packing materi als from your area a nd pla ce them ba ck into the box. Do not dispose of the pa cking materials
until assembly is completed. Read each step carefully before beginning. If you are missing a part please
call our toll-free number for assistance 1 [phone] or e-mail us at:

[e-mail]

STEP 1

Insert REAR SUPPORT(2) into the MAIN FRAME(1) and fasten with ROUND HEAD SCREWS
(M5x0.8x12mm)(57).

STEP 2

Attach FRONT ST ABILIZER(3) onto the MAIN FRAME(1) with CARRIAGE BOL TS(M8x1.25x38mm)(51),
ARC WASHERS(M8)(71), a nd ACOR N NUTS(M8x1.25)(64).

STEP 3

Turn the LEVELING CAPS(48) on the FRONT STABILIZER(3) as needed until bike is steady and not
rocking.

6

ASSEMBLY INSTRUCTIONS

Strap

STEP 4

Attach the SEAT(43) to the SEAT POST(4) with NYLOCK NUTS(M8x1.25)(62) and WASHERS(M8)(67).
Slide BELLOWS(45) over the SEAT POST(4). In sert the SEA T POST(4) into the MAIN FRAME(1) and lock
in position with LOCKING KNOB(46).

STEP 5

Slide the Cable of the TENSION KNOB(27) into the slot on the MONIT OR POST(5). Hook the top end of the
TENSION KNOB(27) into the s quare hole on the MONITOR POST(5) a nd secure with FLA T HEAD SCREW
(M5x0.8x15mm)(58).

STEP 6

NOTE:

Tie the stra p to the plug end of the SPEED PICKUP WIRE(23). Pull the strap from the top of the MONITOR
POST(5) to pull the SPEED PICKUP WIRE(23) through the MONITOR POST(5) as shown in the above

illustration. The SPEED PICKUP WIRE(23) must extend out the top of the MONITOR POST(5).
Attach the MONITOR POST(5) onto the MAIN FRAME(1) by hooking the front end of the Bracket on the
bottom of the MONITOR POST(5)

ROUND HEAD SCREW(M5x0.8x6mm)(73) at front of the Bracket. Secure the back end of the Bracket of
the MONITOR POST(5) with the ROUND HEAD SCREW(M5x15mm)(53). Remove the strap from the

SPEED PICKUP WIRE(23).

There is a strap attached inside of the MONITOR POST(5). This strap is to assist in pulling the
SPEED PICKUP WIRE(23) through the MONIT OR POST(5).

onto the round tube on the MAIN FRAME(1), then secure with the

7