Page 1
Owner's
Manual
W A RNING
Exercise can pre sent a health
risk. Consult a physician
before beginning a ny exercise
program with this equipment.
If you feel faint or dizzy,
immediately discontinue use
of this equipment. Serious
bodily injury can occur if this
equipment is not assembled
and used correctly. Serious
bodily injury can also occur if
all instructions are not
followed. Keep others and
pets away from equipment
when in use. Always make
sure all bolts and nuts are
tightened prior to each use.
Follow all safety instructions in
this manual.
CAUTION:
Weight on this product should not exceed 250 lbs.
This Product is Produced Exclusively by
2040 N. Alliance, Springfield, MO 65803
Customer Service Number
1 (800) 375-7520
www.stamin aproducts.com
2005, 12
When calling for parts or
service, please specify the
following number.
45-1002
STAMINA PRODUCTS
MADE IN CHINA
Product May Vary Slightly
From Pictured.
2005 Stamin a Products, Inc.
Page 2
TABLE OF CONTENTS
Page Page
Safety Instructions 2
Before You Begin 4
Hardware Illustrations 5
Assembly Instructions 6
Using The Electronics Meter 8
Treadmill Adjustments 9
Maintenance 10
Storage 11
Product Parts Drawing 12
Parts List 13
Warranty 14
Fax/Mail Ordering Form 15
SAFETY INSTRUCTIONS
WARNING:
1.
Read all warnings posted on the InMotion
2.
Read this Owner's Manual and follow it carefully before using the InMotionTM II Treadmill. Make
sure that it is properly assembled and tightened before use.
3.
We recommend that two people be available for assembly of this product.
4.
Keep children away from the InMotionTM II Treadmill. Do not allow children to use or play on the
InMotionTM II Treadmill. Keep children and pets away from the InMotionTM II T readmill when it is
in use.
5.
It is recommended that you pla ce this exercise equipment on an equipment mat.
6.
Set up and operate the InMotionTM II Tre admill on a solid level surface. Do not position the InMotion
II Treadmill on loose rugs or uneven surfaces.
7.
Inspect the InMotionTM II T rea dmill for worn or loose components prior to use. T ighten/repla ce a ny
loose or worn components prior to using the InMotionTM II Treadmill.
8.
Keep fingers clear of all pinch points when folding and unfolding the InMotionTM II Treadmill.
9.
When folding the InMotionTM II Treadmill for storage, make sure that Base Frame Assembly is
locked securely in the folded position by the Spring Pin.
10.
Consult a physician prior to commencing an exercise program. If, at any time during exercise, you
feel faint, dizzy, or experience pain, stop and consult your physici an.
11.
Follow your physicia n's recommendations in developing your own personal fitness program.
12.
Always choose the workout which best fits your physical strength and flexibility level. Know your
limits and train within them. Always use common sen se when exercising.
13.
Do not wear loose or dangling clothing while using the InMotionTM II Treadmill.
14.
Never exercise in bare feet or socks; always wear correct footwear, such as running, walking, or
crosstraining shoes. Be sure that they fit well, provide foot support a nd feature non-skid rubber soles.
15.
Be careful to maintain your balance while using, mounting, dismounting, or a ssembling the InMotion
II Treadmill, loss of balance may result in a fall and serious bodily injury.
16.
The InMotionTM II Treadmill should not be used by persons weighing over 250 pounds.
17.
The InMotionTM II Treadmill should be used by only one person at a time.
18.
The InMotionTM II Treadmill is for consumer use only. It is not for use in public or semipublic
facilities.
To reduce the risk of serious injury, read the following Safety Instructions before
using the
InMotionTM II Tr eadmill.
TM
II Treadmill.
TM
TM
WARNING:
Before starting any exercise or conditioning program you should consult with your personal
physicia n to see if you require a complete physical exa m. This is especially i mporta nt if you
are over the age of 35, have never exercised before, are pregnant, or suffer from any
illness. READ AND FOLLOW THE SAFETY PRECAUTIONS. FAILURE TO FOLLOW
THESE INSTRUCTIONS CAN RESUL T IN SERIOUS BODILY INJURY.
2
Page 3
CALL US FIRST
THANK YOU FOR PURCHASING THE
InMotionTM II Treadmill
To help you get started, we have pre-assembled most of your
InMotionTM II Treadmill at the factory with the exception
of those few parts left unassembled for shipping purposes.
Simply follow the few assembly instructions set forth in this manual.
Within a few minutes you will be getting your body into shape and on your
way to achieving a happier and healthier lifestyle.
Should you have any questions,
please call our Customer Service Department toll-free number,
1 (800) 375-7520
Monday - Friday, 8:00 A.M. - 5:00 P.M., Central Time.
3
Page 4
BEFORE YOU BEGIN
Thank you for choosing the InMotion
TM
II
Treadmill. We take great pride in producing this
quality product and hope it will provide many hours
of quality exercise to make you feel better , look better
and enjoy life to its fullest.
Yes, it's a proven fact that a regular exercise
program can improve your physical and mental
health. Too often, our busy lifestyles limit our time
and opportunity to exercise. The
InMotionTM II
Treadmill provides a convenient a nd simple method
to begin your assault on getting your body in shape
and achieving a happier and he althier lifestyle.
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
Read this manual carefully before using the
InMotionTM II Treadmill.
Meter
Although Stamina tries to manufa cture its products
with the finest materials and uses the highest
standards of ma nufacturing, occasionally a part that
does not fit, is the incorrect size, or is otherwise
inappropriate is found. Even with the highest
inspection a nd quality controls in place these things
will happen occasionally. Please do not return the
product. For your convenience, Stamina has a
Customer Service Department with a toll-free
number. If a part is missing, does not fit, is the
incorrect size, or is otherwise inappropriate, please
call 1 (800) 375-7520 (in the U.S.) between 8:00 A.M.
and 5:00 P.M. Central T ime, Monday through Friday .
Our operators will be able to assist you with your
problem and the parts will be mailed dire ctly to your
house.
U-Sha ped Ha ndrail
Left Upright
Flywheel
Upright Support
Moving Wheel
Spring Pin
Base Frame
Right Upright
Wal king Belt
Side Molding
Adjustment
Bracket
Bumper Stand
THE FOLLOWING TOOLS ARE REQUIRED FOR ASSEMBLY : Wrench
Allen Wrench (4mm)
4
Page 5
HARDWARE IDENTIFICATION CHAT
This chart is provided to help identify the hardware used in the assembly process.
After unpa cking the unit, open the hardware bag and make sure that you have the following items:
3/16" 5/16" 1/2"3/8"1/4"
INCHES
11/2021/2 31/2 41/2 51/2 61/2
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
MILLIMETERS
6 8 10 12
Place washers, the end of bolts or screws on the circles to check for the
correct size. Use the small scale to check the sizes of bolts and screws.
NOTICE: The length of all kinds of screws and bolts are not included
themselves head, except the flat head screws and bolts.
Part No. and Description Qty
38 Bolt, Hex Hea d (M10 x 1.5 x 20mm) 4
in.
mm.
length
length
NOTE:
39 Bolt, Hex Hea d (M12 x 1.75 x 70mm) 2
40 Bolt, Button Head (M6 x 1 x 15mm) 2
44 Arc Washer (M6) 2
47 Washer (M10) 4
48 Washer (M12) 2
1. Some of the hardware items listed may be attached to other parts.
2. Bolt length is measured from the bottom of the bolt head to the end of the bolt.
5
Page 6
ASSEMBLY INSTRUCTIONS
Place all parts from the box in a cleared area and position them on the floor in front of you. Remove all
packing materi als from your area a nd pla ce them ba ck into the box. Do not dispose of the pa cking materials
until assembly is completed. Read each step carefully before beginning. If you are missing a part please
call our toll-free number for assistance 1 (800) 375-7520 or e-mail us at:
parts@staminaproducts.com
Sensor Wire
STEP 1
NOTE: The LEFT UPRIGHT(2) is the one with the Sensor Wire.
Attach the
LEFT and RIGHT UPRIGHTS(2, 3) to the UPRIGHT SUPPORT(4) with HEX BOLTS
(M10 x 20mm)(38) and WASHERS(M10)(47).
STEP 2
Slide the SPRING(7) onto the SPRING PIN(6). Insert the threaded end of the SPRING PIN(6) through
the collar on the
RIGHT UPRIGHT(3) and screw the BALL KNOB(8) onto the thread end of the SPRING
PIN(6). Tighten the BALL KNOB(8) as tight as you can by hand.
6
Page 7
ASSEMBLY INSTRUCTIONS
STEP 3: Place the BASE FRAME(1) between the LEFT and RIGHT UPRIGHTS(2, 3) and secure
HEX BOL TS(M12 x 70mm)(39) and W ASHERS(M12)(48). DO NOT TIGHTEN COMPLETEL Y.
with
STEP 4: Secure the U-SHAPED HANDRAIL(5) onto the LEFT and RIGHT UPRIGHTS(2, 3) with
BUTTON HEAD BOLTS(6mm x 15mm)(40) and ARC WASHERS(M6)(44). Connect the UPPER
EXTENSION WIRE(28) to the LOWER EXTENSION WIRE(29).
STEP 5: Go back and tighten HEX BOLTS(M12 x 70mm)(39) in STEP 2. Connect the LOWER
EXTENSION WIRE(29) located on the LEFT UPRIGHT(2) to the SENSOR WIRE(30). Insert the
PULL PIN(9) through the RIGHT UPRIGHT(3) and BASE FRAME(1) to lock the BASE FRAME(1) in
position.
STEP 6: Install two "AA" batteries into the METER(26), two batteries included. See page 8 for detailed
battery installation instructions. Slide the
Connect the UPPER EXTENSION WIRE(28) to the METER(26).
METER(26) onto the plate on the U-SHAPED HANDRAIL(5).
STEP 7: Attach the BUMPER STANDS(22) to the bottom of the BASE FRAME(1).
NOTE: The BUMPER ST ANDS(22) may be stored on the end of the BASE FRAME(1) to increase the
angle of the treadmill and reduce the walking resistance. See page 10 for details on adjusting the walking
resistance.
7
Page 8
USING THE ELECTRONIC METER
POWER ON :
POWER OFF :
MODE / CLEAR BUTTON:
Walking Belt movement or push the button.
Automatic shut off after 4 minutes of ina ctivity .
Press and rele ase to select functions.
Press and hold f or three seconds to reset all
functions to zero.
FUNCTIONS:
SCAN:
TIME:
SPEED:
Automatically scans TIME, SPEED, DISTANCE, and CALORIES in sequence with a change
every four seconds. Press a nd release the button until "
to SCAN.
Displays the time, from 1 sec. up to 99:59 minutes.
Displays the current speed, from zero to 999.9 Mile/Hr.
" a ppears on the display a nd points
DISTANCE:
CALORIES:
Displays the distance, from zero to 99.99 miles.
Displays the calorie consumption, from zero to 999.9 Kcal.
The calorie readout is an estimate for a n average user. It should be used only a s a comparison
between workouts on this unit.
HOW TO INSTALL AND REPLACE BATTERY:
Open the Battery Door on the back of the meter.
1.
The meter operates with two AA batteries, two batteries included.
2.
Refer to the illustration to install or replace the batteries.
NOTE:
Do not mix a new battery with an old battery.
1.
Use the same type of battery. Do not mix an alkaline battery with
2.
another type of battery.
Rechargeable batterie s are not recommended.
3.
AA Batteries
8
Page 9
TREADMILL ADJUSTMENTS
The ba sic idea behind the ma nual treadmill is to have the belt running on a tre admill board a nd between two
rollers so that the belt will move without much effort. In order for the belt to run smoothly, there are a few
points that need to be noted.
BELT ALIGNMENT
The belt must be in the center of the treadmill to prevent it from rubbing against the flywheels. If the belt
rubs a flywheel, it will be difficult to keep the belt moving and eventually damage the edge of the belt.
The treadmill has belt guides welded to the bottom of the treadmill frame that move the belt toward the
center of the treadmill. However, the rear roller must be properly aligned with the treadmill frame and front
roller if the belt is to remain centered on the treadmill.
The bolts in the rear of the treadmill (one on the left and the other on the right) adjust the alignment of the
rear roller as well as the tension of the belt.
The belt will run to the side of the loose rear bolt.
Hint:
Eyeball the rear roller to make sure both the right side and the left side of the roller are the same
distance from the back edge of the treadmill. Use the
adjustments. Turn the bolts Clockwise to tighten and Counter-Clockwise to loosen.
4mm ALLEN WRENCH to make these
BEL T D RIFTING LEFT
Turn the left screw 1/4 turn CLOCKWISE and the right screw 1/4 turn
COUNTER-CLOCKWISE, then walk on the treadmill. Repeat if needed.
BEL T DRIFTING RIGHT
Turn the left screw 1/4 turn COUNTER-CLOCKWISE and the right screw
1/4 turn CLOCKWISE, then walk on the treadmill. Repeat if needed.
LEFT
ADJUSTMENT
RIGHT
ADJUSTMENT
NOTE:
When you believe the WALKING BELT is centered, use the treadmill for three (3) minutes to verify the
WALKING BELT won't drift to one side. If the WALKING BEL T continue s to drift, the floor may not be level.
Rotate the treadmill 90 degrees or move the tre admill to another location.
BELT TENSION
The belt should be tight and not lying on the trea dmill board. If the belt is too loose, the belt will slip on the
front roller and you will notice a jerky movement when you walk on the treadmill. If the belt is too tight, the
edges of the belt will begin to curl and more ef fort will be required to move the belt. Excessive belt tension
can also damage the bearings in the rollers. The bolts in the rear of the treadmill (one on the left and the
other on the right) adjust the tension of the belt as well as the alignment of the rear roller.
BELT TOO LOOSE: Use the 4mm ALLEN WRENCH to tighten the bolts in the rear of the treadmill.
Tighten both rollers 1/4 turn at a time until the belt stops slipping on the front roller.
BELT TOO TIGHT: Use the 4mm ALLEN WRENCH to loosen the bolts in the rear of the treadmill.
Loosen both rollers 1/2 turn at a time until the belt begins to sli p on the front roller . Then use the procedure
above to tighten the belt.
9
Page 10
TREADMILL ADJUSTMENTS
WALKING RESISTANCE
The walking resistance or effort needed to push the treadmill belt can be adjusted by changing the incline
angle. This treadmill has two adjustment positions.
Highest Re sistance
The BUMPER STANDS(22) are attached to
the bottom of the treadmill.
Remove (unscrew) the BUMPER STANDS(22)
from the bottom of the treadmill and store them
Lowest Re si stance
in the end of the treadmill.
NOTE:
Since this is a new machine, you may need some time to get used to walking on the treadmill and to
1.
break it in.
If the walking resistance is still too high, check the
2.
The belt resistance can be reduced by adding silicone lubricant between the belt and the board. Wipe
3.
the board under the belt with a cloth and spray or spread silicone lubricant on the board under the belt.
BELT TENSION.
MAINTENANCE
The safety and integrity designed into the InMotion
InMotionTM II Tr e admill is regularly examined for damage a nd wear . Spe cial attention should be given to
the following:
1.
Clean the exposed surfaces of the walking belt and the board with an absorbent cloth.
2.
It is the sole responsibility of the user/owner to ensure that regular maintenance is performed.
3.
Verify that the Spring Pin is present and functioning properly. Verify that the Ball Knob is securely
attached to the Spring pin. Repair or replace parts as necessary.
4.
Verify that all nuts a nd bolts are present a nd properly tightened. Repla ce missing nuts and bolts. T ighten
loose nuts and bolts.
5.
Verify that the Warning Label is in place and easy to read. Call Stamina Products immediately
(1-800-375-7520) for a replacement Warning Label if the Warning Label is missing or damaged.
6.
Worn or da maged components shall be replaced immediately or the
from service until repair is made.
Only Stamina Products supplied components shall be used to maintain/repair the
7.
Treadmill.
Keep your InMotion
8.
WALKING BELT(17) does not move easily, lubricate the BOARD(18) under the WALKING
If the
9.
TM
II Tr eadmill clean by wiping with an absorbent cloth after use.
BELT(17) with Silicone Lubricant.
TM
II Treadmill can only be maintained when the
InMotionTM II Tr ea dmill removed
InMotionTM II
10
Page 11
STORAGE
1.
To store the
2.
T o avoid da mage to the electronics meter , remove the batteries before storing the
for one year or more.
3.
Follow the following process to fold The
a.
Remove the PULL PIN(9) to unlock the BASE FRAME ASSEMBLY(1).
Fold up the BASE FRAME ASSEMBLY(1). Pull out the BALL KNOB(8) on the spring pin and
b.
release to lock the
CAUTION: Make sure the Base Frame Assembly is locked se curely in folded position by the spring pin.
Store the
c.
4.
Move the
U-SHAPED HANDRAIL(6) to move the InMotionTM II Treadmill.
the
InMotionTM II Tr eadmill simply keep it in a clean dry place.
InMotionTM II T rea dmill
InMotionTM II Tr eadmill as illustrated for e asy storage.
BASE FRAME ASSEMBLY(1) in upright position.
PULL PIN(9) by inserting the PULL PIN(9) back into the hole in the RIGHT UPRIGHT(3).
InMotionTM II Treadmill with the moving wheels on the UPRIGHT SUPPORT(4). Grasp
UNFOLD THE InMotionTM II Treadmill
Remove the PULL PIN(11) from the RIGHT UPRIGHT FRAME(3).
a.
Pull out the BALL KNOB(10) on the spring pin and unfold the BASE FRAME ASSEMBLY(1).
b.
Lock the BASE FRAME ASSEMBL Y(1) in position by inserting the PULL PIN(1 1) through the RIGHT
c.
UPRIGHT FRAME(3) and BASE FRAME(1).
11
Page 12
PRODUCT PARTS DRAWING
FRONT
Belt Guides
12
BACK
Page 13
PARTS LIST
DIAGRAM# PART NAME QTY
1 Ba se Frame 1
2 Left Upright 1
3 Right Upright 1
4 Upright Support 1
5 U-Shaped Handrail 1
6 Spring Pin 1
7 Spring 1
8 Ball Knob 1
9 Pull Pin 1
10 Front Roller /w Flywheels 1
11 Front Shaft 1
12 Bearing (6000zz) 4
13 Pla stic Washer (M10) 4
14 Rear Roller 1
15 Rear Shaft 1
16 Adjustment Bra cket 2
17 Walking Belt 1
18 Board 1
19 Left Side Molding 1
20 Right Side Molding 1
21 Round Cap (38mm) 2
22 Bumper Stand 2
23 Moving Wheel 2
24 Foam Grip 2
25 Long Foam Gri p 2
26 Meter 1
27 Grommet Plug 4
28 Upper Extension Wire 1
29 Lower Extension Wire 1
30 Sensor Wire 1
31 Magnet 1
32 Screw Sleeve 6
33 Round Plug (25mm) 2
34 Rectangular Plug (25mm x 50mm) 2
35 Screw , Flat Head (M3.5 x 15mm) 2
36 Screw, Flat Head (M5 x 25mm) 6
37 Bolt, Hex Head (M6 x 1 x 55mm) 2
38 Bolt, Hex Head (M10 x 1.5 x 20mm) 4
39 Bolt, Hex Head (M12 x 1.75 x 70mm) 2
40 Bolt, Button Head (M6 x 1 x 15mm) 2
41 Bolt, Button Head (M6 x 1 x 70mm) 2
42 Bolt, Button Head (M8 x 1.25 x 15mm) 2
43 Nylock Nut (M6 x 1) 2
44 Arc Washer (M6) 2
45 Washer (M6) 6
46 Washer (M8) 2
47 Washer (M10) 4
48 Washer (M12) 2
49 Warning label 1
50 Wrench 1
51 Allen Wrench (4mm) 1
52 Owner's Manual 1
13
Page 14
LIMITED WARRANTY
MODEL 45-1002
WARRANTY
Stamina Products, Inc. warrants that this product will be free from defects in materials and workmanship
under normal use, service and proper operation for a period of 90 days on the parts and one year on the
frame from the date of the original purchase from an authorized retailer. THIS WARRANTY SHALL NOT
APPLY TO ANY PRODUCT WHICH HAS BEEN SUBJECT TO COMMERCIAL USE, ABUSE, MISUSE,
ALTERATION OF ANY TYPE OR CAUSE OR TO ANY DEFECT OR DAMAGE CAUSED BY REPAIR,
REPLACEMENT , SUBSTITUTION OR USE WITH P ARTS OTHER THAN P ARTS PROVIDED BY ST AMINA
PRODUCTS, INC. Commercial use includes use of the product in athletic clubs, health clubs, spas,
gymnasiums, exercise facilitie s, and other public or semipublic facilities whether or not the product's use is
in furtherance of a profit making enterprise, and all other use which is not for personal, family, or household
purposes.
T o i mplement this li mited warranty, send a written notice stating your name, date, a nd pla ce of purcha se a nd
a brief description of the defect along with your rece ipt to Sta mina Products, Inc. P .O. Box 1071, Springf ield
Missouri, USA, 65801-1071 or call us at 1 (800) 375-7520. If the defect is covered under this limited
warranty , you will be reque sted to return the product or part to us for free repair or repla cement at our option.
NO ACTION FOR BREACH OF THIS LIMITED WARRANTY MA Y BE COMMENCED MORE THAN ONE
(1) YEAR AFTER THE DATE THE ALLEGED BREACH WAS OR SHOULD HAVE BEEN DISCOVERED.
NO ACTION FOR BREACH OF ANY IMPLIED WARRANTY MAY BE COMMENCED MORE THAN ONE
(1) YEAR AFTER DELIVERY OF THE PRODUCT TO THE PURCHASER. This limited warranty is not
transferable. IF ANY PART OF THE PRODUCT IS NOT IN COMPLIANCE WITH THIS LIMITED
WARRANTY OR ANY IMPLIED WARRANTY, THE REMEDY OF REPAIR OR REPLACEMENT IS THE
EXCLUSIVE REMEDY AVAILABLE T O YOU. In the event that the purchaser makes a ny clai m under this
limited warra nty or any implied warra nty , the Warra ntor reserves the right to require the product to be returned
for inspection, at the purchaser's expense, to the Warrantor's premises in Springfield, Missouri. Return of
the enclosed warranty registration card is not required for warranty coverage, but is merely a way of
establishing the date a nd place of purchase.
Sta mina Products, Inc. SHALL NOT BE LIABLE FOR THE LOSS OF USE OF ANY PRODUCT, LOSS OF
TIME, INCONVENIENCE, COMMERCIAL LOSS OR ANY OTHER INDIRECT, CONSEQUENTIAL,
SPECIAL OR INCIDENT AL DAMAGES DUE TO BREACH OF THE ABOVE WARRANTY OR ANY IMPLIED
WARRANTY.
This limited warra nty is the only written or express warranty given by Stamina Products, Inc. This warra nty
gives you specific legal rights, and you may also have other legal rights which vary from state to state.
ANY OTHER RIGHT WHICH YOU MAY HAVE, INCLUDING ANY IMPLIED WARRANTY OR
MERCHANT ABILITY OR FIT NESS FOR A P ARTICULAR PURPOSE, IS LIMITED IN DURA TION TO THE
DURA TION OF THIS WARRANTY.
The laws in some jurisdictions restrict the rights of manufacturers and distributors of consumer goods to
disclaim or limit implied warranties and consequential and incidental damages with respect thereto. If any
such law is found to be a pplicable, the foregoing disclai mers a nd limitations of a nd on implied warrantie s and
consequential a nd incidental da mages with respect thereto shall be disregarded a nd shall be deemed not to
have been made to the extent necessary to comply with such legal re striction.
14
Page 15
FAX/MAIL ORDERING FORM
Plea se do not return the product. For your convenience, Sta mina has a Customer Service Department with
a toll-free number. Should a part be missing or a defective part found, please call 1 (800) 375-7520
(in the U.S.) between 8:00 A.M. and 5:00 P .M. Central T i me, Monday through Friday or fill out the fax sheet
ordering form below a nd fax it to (417) 889-8064. Our Customer Service Department will be able to assist
you with your problem and the part will be mailed dire ctly to your house.
TELEPHONE
CUSTOMER SERVICE
Tel: 1 (800) 375-7520
FAX
CUSTOMER SERVICE
Fax: (417) 889-8064
ONLINE
CUSTOMER SERVICE
parts@staminaproducts.com
www.staminaproducts.com
STAMINA PRODUCTS, INC.
ATTN: Customer Service
Springfield, MO. 65801-1071
Detach and Mail or Fax the Form Below
Stamina Products, Inc.
P.O. Box 1071
Springfield, MO 65801-1071
Mr./Ms:
Address: Apt. #:
City: State: Zip Code:
IMPORTANT : We must have your phone number in order to process the order!
Phone #: ( ) Work Phone #: ( )
Date Purchased:
Model #:
Purchased From:
IMPORTANT : Before filling out the form below make sure you have the right information.
Refer to the parts list to make sure you're ordering the right parts!
MAIL
P.O. Box 1071
EXAMPLE:
P ART # DESCRIPTION QUANTITY
1 Rear Unit Assembly 1
Loading...