Stamina Products 55-1772 User Manual

Owner's

Manual

W A RNING

Exercise can pre sent a health
risk. Consult a physician
before beginning a ny exercise
program with this equipment.
If you feel faint or dizzy,
immediately discontinue use
of this equipment. Serious
bodily injury can occur if this
equipment is not assembled
and used correctly. Serious
bodily injury can also occur if
all instructions are not
followed. Keep others and
pets away from equipment
when in use. Always make
sure all bolts and nuts are
tightened prior to each use.
Follow all safety instructions in
this manual.

CAUTION:
Weight on this product should not exceed 250 lbs.

This Product is Produced Exclusively by

2040 N. Alliance, Springfield, MO 65803

Customer Service

1 [phone]

2008, 07

www.stamin aproducts.com

When calling for parts or
service, please specify the
following number.

Model#: 55-1772

STAMINA PRODUCTS

MADE IN CHINA

Product May Vary Slightly

From Pictured.

2008 Stamina Products, Inc.

TABLE OF CONTENTS

Page Page

Safety Instructions 2
Before You Begin 4
Equipment Warning & Notice Labels 5
Hardware Identification Chart 6
Assembly Instructions 7
Set Up Instructions 12
Operational Instructions 13
Storage 15

Maintenance 15
Conditioning Guidelines 16
Warm-Up a nd Cool-Down 17
Product Parts Drawing 18
Parts List 19
Warra nty 21
Notes 22
Fax/Mail Ordering Form 23

SAFETY INSTRUCTIONS

WARNING:

Read all warnings posted on the Magnetic 1772 Elliptical.

1.
The Magnetic 1772 Elliptical should only be used after a thorough review of the Owner's Manual.

2.
We recommend that two people be available for assembly of this product.

3.
Keep children away from the Magnetic 1772 Elliptical. Do not allow children to use or play on the

4.
Magnetic 1772 Elliptical. Kee p children and pets away from the Magnetic 1772 Elliptical when it is
in use.
Make sure the

6.
tightened before use.

7.

It is recommended that you pla ce this exercise equipment on an equipment mat.

8.

Set up and operate the Magnetic 1772 Elli ptical on a solid level surface. Do not position the Magnetic
1772 Elliptical on loose rugs or uneven surfa ces.

9.

Make sure that a dequate spa ce is availa ble for access to and around the Magnetic 1772 Elliptical.

10.

Adjust the LEVELING CAPS on the REAR ST ABILIZER so that the bike sits on the floor without rocking.

11.

Before using, inspect the
replace any loose or worn components prior to use.

13.

Consult a physicia n prior to commencing a n exercise progra m a nd follow his/her recommendation s
in developing your fitness progra m. If at a ny time during exercise you feel faint, dizzy , or experience
pain, stop and consult your physician.

14.

Follow your physicia n's recommendations in developing your own personal fitness program.

15.

Always choose the workout which best fits your physical strength and flexibility level. Know your
limits and train within them. Always use common sen se when exercising.

16.

Do not wear loose or dangling clothing while using the Magnetic 1772 Elliptical.

17.

Never exercise in bare feet or socks; always wear proper footwear such as running, walking, or
cross training shoes that fit well, provide foot support, and feature non-skid rubber soles.

18.

Care should be taken in mounting or dismounting the Magnetic 1772 Elliptical.

19.

The Magnetic 1772 Elliptical should not be used by persons we ighing over 250 pounds.

20.

The Magnetic 1772 Elliptical should be used by only one person at a time.

21.

The Magnetic 1772 Elliptical is for consumer use only. It is not for use in public or semipublic
facilities.

To reduce the risk of serious injury, read the following Safety Instructions before
using the Magnetic 1772 Elliptical.

Magnetic 1772 Elliptical is properly assembled and that all nuts and bolts are

Magnetic 1772 Elliptical for worn or loose components, and tighten or

WARNING:

Before starting any exercise or conditioning program you should consult with your personal
physicia n to see if you require a complete physical exa m. This is especially i mporta nt if you
are over the age of 35, have never exercised before, are pregnant, or suffer from any
illness. READ AND FOLLOW THE SAFETY PRECAUTIONS. FAILURE TO FOLLOW

THESE INSTRUCTIONS CAN RESUL T IN SERIOUS BODILY INJURY.

2

CALL US FIRST

Customer Service

1(800) 375-7520

www.staminaproducts.com

THANK YOU FOR PURCHASING THE

Magnetic 1772 Elliptical

To help you get started, we have pre-assembled most of your

Magnetic 1772 Elliptical at the factory with the exception

of those few parts left unassembled for shipping purposes.

Simply follow the few assembly instructions set forth in this manual.

With regular workouts, you will be getting your body into shape

and be on your way to achieving a ha ppier and healthier lifestyle.

Should you have any questions,

please call our Customer Service Department toll-free number,

1 [phone]

Monday - Thursday, 7:30 A.M. - 5:00 P.M., Central Time.

Friday, 8:00 A.M. - 3:00 P.M., Central Time.

TELEPHONE

CUSTOMER SERVICE

Tel: [phone]

FAX

CUSTOMER SERVICE

Fax: [phone]

ONLINE

CUSTOMER SERVICE

[e-mail]

www.staminaproducts.com

STAMINA PRODUCTS, INC.

ATTN: Customer Service

Springfield, MO. 65801-1071

MAIL

P.O. Box 1071

3

BEFORE YOU BEGIN

Thank you for choosing the Magnetic 1772
Elliptical. We take great pride in producing this

quality product and hope it will provide many hours
of quality exercise to make you feel better , look better ,
and enjoy life to its fullest.
It's a proven fact that a regular exercise program
can improve your physical and mental health. Too
often, our busy lifestyles limit our ti me and opportunity
to exercise. The Magnetic 1772 Elliptical provides
a convenient and si mple method to begin your assault
on getting your body in sha pe and a chieving a happier
and healthier lifestyle.
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
Read this manual carefully before using the

Magnetic 1772 Elliptical.

Foam Gri p

Although Stamina constructs its products with the
finest materials and uses the highest standards of
manufacturing and quality control, there can
sometimes be missing parts or incorrectly sized
parts. If you have any questions or problems with
the parts included with your Magnetic 1772
Elliptical, plea se do not return the product. Contact
us FIRST!
If a part is missing or defective, please call us toll
free at 1-800-375-7520 (in the U.S.). Our Customer
Service Staff is available to a ssist you from 7:30 A.M.
to 5:00 P .M. (Central T ime) Monday through Thursday
and 8:00 A.M. to 3:00 P.M. (Central T i me) on Friday.
If you would like to contact us online, go to our
website at www .stamin aproducts.com a nd a ccess the
Customer Service section.
Be sure to have the na me and model number of the
product available when you conta ct us.

Meter

Left Pedal Cap

Left Pedal Arm

Right Crank

Left Cover

Leveling Cap

Rear Stabilizer

Left Handlebar

Pulse Sensor Plate s

Tension Knob

Lower Pivoting Arm

Foam Gri p

Right Handlebar

Upright
Warning Label

Lower Pivoting Arm

Linkage

Wheel

Front Stabilizer
Right Pedal Cap
Right Pedal Arm

THE FOLLOWING TOOLS ARE INCLUDED FOR ASSEMBLY :

4

Allen Wrench (6mm)

Multi-opening Wrench

EQUIPMENT WARNING & NOTICE LABELS

This chart is provided to help identify the warning & notice labels on the Magnetic 1772 Elliptical. Please
take a moment to familiarize yourself with all of the warning & notice labels.

Label is larger than actual size

W1

WAR NING LABEL(91)

5

HARDWARE IDENTIFICATION CHART

This chart is provided to help identify the hardware used in the a ssembly process. Place the washers or the
ends of the bolts or screws on the circles to check for the corre ct diameter. Use the small scale to check the
length of the bolts and screws.

3/16" 5/16" 1/2"3/8"1/4"

INCHES

11/2021/2 31/2 41/2 51/2 61/2

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

MILLIMETERS

6 8 10 12

NOTICE: The length of all bolts and screws, except those with flat heads,

is mea sured from below the hea d to the end of the bolt or screw .
Flat head bolts and screws are measured from the top of the
head to the end of the bolt or screw.

After unpacking the unit, open the hardware bag and make sure that you have all the following items.
Some hardware may be already attached to the part.

length

length

in.

mm.

Part No. and Description Qty

64 Carriage Bolt (M8 x 1.25 x 75mm) 2

65 Bolt, Button Head (M8 x 1.25 x 15mm) 9
66 Bolt, Button Head (M8 x 1.25 x 20mm) 2

67 Bolt, Button Head (M8 x 1.25 x 48mm) 2
68 Bolt, Button Head (M8 x 1.25 x 75mm) 2

72 Bolt, Hex Hea d (M6 x 1 x 35mm) 4

75 Screw, Round He ad (M5 x 15mm) 6

81 Nylock Nut (M8 x 1.25) 2

84 Acorn Nut (M6 x 1) 4
85 Acorn Nut (M8 x 1.25) 2

86 Arc Wa sher (M6) 4
87 Arc Washer (M8) 13

88 Lock Washer (M6) 4
89 Lock Washer (M8) 15

45 Large Washer (M8 x ø32 x 2mm thick) 2
52 Large Washer (M16 x ø32 x 0.5mm thick) 2

6

ASSEMBLY INSTRUCTIONS

Place all parts from the box in a cleared area and position them on the floor in front of you. Remove all
packing materi als from your area a nd pla ce the m ba ck into the box. Do not dispose of the pa cking materi als
until a ssembly is completed. Read e a ch step carefully before beginning. If you are missing a part please call
our toll-free number for a ssistance 1-800-375-7520 or e-mail us at: customerservice@sta min aproducts.com

STEP 1

Attach the FRONT STABILIZER(2) to the MAIN FRAME(1) with CARRIAGE BOLTS(M8x1.25x75mm)
(64), ARC W ASHERS(M8)(87), LOCK WASHERS(M8)(89), a nd ACOR N NUTS(M8x1.25)(85).

STEP 2

Attach the REAR STABILIZER(3) to the MAIN FRAME(1) with BUTTON HEAD BOL TS(M8x1.25x 75mm)
(68), ARC WASHERS(M8)(87), and LOCK WASHERS(M8)(89).
NOTE:

You can adjust the LEVELING CAPS(61) on the REAR STABILIZER(3) to keep the Magnetic
1772 Elliptical stable.

7

ASSEMBLY INSTRUCTIONS

Metal Fitting

Cable End

Bracket

Spring Hook

STEP 3

Refer to the inset drawing. Lay the UPRIGHT(6) on the floor close to the front of the MAIN FRAME(1). Set
the TENSION KNOB(25) on the UPRIGHT(6) at position 8, so the CABLE END of the TENSION KNOB

KNOB(25) extends out of the metal fitting as far as possible. Connect the CABLE END of the TENSION
KNOB(25) to the SPRING HOOK end of the TENSION CABLE(24). Pull the CABLE END on the TENSION
KNOB(25) firmly a nd insert the ca ble through the slot in the bra cket. Then in sert the metal fitting on the end

of the CABLE END of the TENSION KNOB(25) into the hole at the end of the slot in the BRACKET. Adjust
the TENSION KNOB(25) and verify that the SPRING HOOK moves when the TENSION KNOB(25) is
adjusted.

STEP 4

Plug the SENSOR WIRE(30) firmly into the CONNECTION WIRE(29). CAUTION: Be careful not to da mage
the SENSOR WIRE(30) and CONNECTION WIRE(29) when assembling the UPRIGHT(6).

STEP 5

Insert the UPRIGHT(6) onto the MAIN FRAME(1) and secure with BUTT ON HEAD BOLTS(M8x1.25x15mm)
(65), ARC WASHERS(M8)(87), a nd LOCK WASHERS(M8)(89). Do not tighten the bolts until STEP 10.

8

ASSEMBLY INSTRUCTIONS

LEFT

L

L

R

R

RIGHT

STEP 6

There is an "L" decal on the LEFT PEDAL ARM(4), and an "R" decal on the RIGHT PEDAL

NOTE:

Place the front end of the RIGHT PEDAL ARM(5) on the ROLLER(58) of the FRONT STABILIZER(2).
Connect the ba ck end of the RIGHT PEDAL ARM(5) to the RIGHT CRAN K(36). Thread the RIGHT PEDAL

SHAFT(42) into the RIGHT CRANK (36) and tighten securely. Repeat on the left side.

STEP 7

There is an "L" decal on the LEFT PEDAL CAP(46), and an "R" decal on the RIGHT PEDAL CAP(47).
Attach the RIGHT PEDAL CAP(47) to the RIGHT PEDAL ARM(5) with ROUND HEAD SCREWS

(M5x15mm)(75). Repeat on the left side.
NOTE:

1.

ARM(5).

2.

The RIGHT PEDAL SHAFT(42) has right hand threa ds and is tightened by turning clockwise.
The LEFT PEDAL SHAFT(41) ha s left hand threa ds and is tightened by turning counterclockwise.

The LEFT a nd RIGHT PEDAL CAPS(46, 47) have a raised lip on three side s. Attach the LEFT and
RIGHT PEDAL CAPS(46, 47) to the LEFT a nd RIGHT PEDAL ARMS(4, 5) so that the side without
the raised lip is on the outside.

9

ASSEMBLY INSTRUCTIONS

LEFT

L

Look down from the top

Pivot Tube

Shaft

R

Pivot Tube

RIGHT

STEP 8: There is an "L" decal on the LEFT HANDLEBAR(8), a nd an "R" decal on the RIGHT HANDLEBAR

(9). To a ssemble the RIGHT HANDLEBAR(9), pla ce a SPACER(51) and a LARGE W ASHER(M16)(52) on

the right side of the SHAFT on the UPRIGHT(6). Slide the RIGHT HANDLEBAR(9) onto the SHAFT and
secure with a LARGE WASHER(M8)(45), LOCK WASHER(M8)(89), and BUTTON HEAD BOLT

(M8x1.25x20mm)(66). Repeat on the left side.

STEP 9: Attach the LOWER PIVOTING ARMS(10) to the LEFT and RIGHT HANDLEBARS(8, 9) with HEX

BOLTS(M6x1x35mm)(72), ARC WASHERS(M6)(86), LOCK WASHERS(M6)(88), and ACORN NUTS
(M6x1)(84). Attach the LOWER PIVOTING ARMS(10) to the LINKAGES(11) on the PEDAL ARMS(4, 5) at
both sides with the PLASTIC WASHERS(M8)(49), BUTTON HEAD BOLTS(M8x1.25x48mm)(67), and
NYLOCK NUTS(M8x1.25)(81).

STEP 10: Look down from the top of the UPRIGHT(6) to make sure the PIVOT TUBES on the

HANDLEBARS(8, 9) are parallel to the FRONT ST ABILIZER(2) a nd the PEDAL ARMS(4, 5) are crossing

the ROLLERS(58) properly. T ighten the BUTTON HEAD BOL TS(M8x1.25x15mm)(65) on the UPRIGHT(6)
from STEP 5 on page 8.

10

ASSEMBLY INSTRUCTIONS

A. B.

Strap

STEP 11

Refer to illustration A. Tie the STRAP to the plug end of the PULSE SENSOR WIRE(27). Pull the STRAP
from the square hole on the top of the UPRIGHT(6) until the PULSE SENSOR WIRE(27) is pulled through
and extends out of the square hole. Attach the STATIONARY HANDLEBAR(7) to the UPRIGHT(6) with

BUTTON HEAD BOL TS(M8x1.25x15mm)(65), ARC WASHERS(M8)(87), a nd LOCK W ASHERS(M8)(89).

STEP 12

Refer to illustration B. Install two AA batterie s into the METER(26). T wo batteries are included. See page 14
for detailed battery installation instructions. Connect the PULSE SENSOR WIRE(27) and CONNECTION

WIRE (29) to the METER(26). Slide the METER(26) onto the plate on the UPRIGHT(6).
CAUTION:

Be careful not to da mage the PULSE SENSOR WIRE(27) a nd CONNECTION WIRE(29) when
sliding the

METER(26).

11

SET UP INSTRUCTIONS

Place the M agnetic 1772 Elliptical in the are a where it will be used. It is re commended that the Magnetic
1772 Elliptical be pla ced on an equi pment mat. The maxi mu m operation dimen sions of the Magnetic 1772
Elliptical are approximately 54 inches long x 59 1/2 inches tall x 24 3/8 inches wide. (These dimensions
may vary up to one inch.) An area 4 feet wide x 7 feet long is required for safe operation of the Magnetic
1772 Elliptical. Make sure that a dequate spa ce is available for a ccess to a nd passage around the Magnetic
1772 Elliptical.

LEVELING:

MOVING:

Adjust the LEVELING CAPS(61) on the REAR STABILIZER(3) so that the Magnetic 1772
Elliptical sits on the floor without rocking.

The Magnetic 1772 Elliptical has a pair of WHEELS(60) on the FRONT STABILIZER(2).
Grasp the STATIONARY HANDLEBAR(7) and tip the Magnetic 1772 Elliptical forward to
move.

Stationary Handlebar(7)

Equipment Mat

FUNCTION INSPECTION:

Visually inspect the Magnetic 1772 Elliptical to verify that assembly is as shown in the above illustration.
Check the function of the Magnetic 1772 Elliptical, stand on the foot pedals and place your hands at a
comfortable position on the ha ndlebars. Slowly move your highest foot forward a nd follow the n atural path of
the machine. Turn the crank slowly through one complete revolution to verify that the drive train functions
properly . Adjust the TENSION KNOB(25) and verify that it functions properly.

CAUTION:

Locate and rea d the W A RNING LABEL(91) on the Magnetic 1772 Elli ptical. Ma ke sure that
all users read the WARNING LABEL(91).

12

OPERATIONAL INSTRUCTIONS

LOAD ADJUSTMENT

T o increa se the load, turn the TENSION K NOB(25) clockwise.
To decrease the load, turn the TENSION KNOB(25)
counterclockwise.

NOTE: The load will increase as you pedal faster.

EXERCISE WORKOUT

To start using the Magnetic 1772 Elliptical simply stand on the foot pedals with the front of your shoes
close to the front edge of the pedal cap. Place your hands at a comfortable position on the handlebars.
Simply move your highest foot forward and follow the n atural path of the machine.

Start on a load level that is comforta ble to familiarize yourself with the machine. Once you are comforta ble,
start adjusting the load level to achieve the workout desired.

Forward and Reverse

The M agnetic 1772 Elliptical ca n be used in the forward a nd reverse direction to vary the muscles that you
work out. This will also vary your workout, helping you to stay motivated. To change directions, si mply slow
the pedals down until they stop, and switch direction s.

Load Level Adjustment

The load level of Magnetic 1772 Elliptical ca n be changed at any time during your workout. Adjusting your
load level will allow you to increase or decrease your intensity level.

13

USING THE METER

POWER ON:

POWER OFF:

Pedal movement or press any button.
Automatic shut off after 4 minutes of
inactivity. Resets all values to zero.

Upper

Display

FUNCTION BUTTONS:

MODE :

SET :

RESET :

Press and release to select each function for
display on Upper Display or preset target values.
Press the button and hold it down for three
seconds to reset all functions to zero.

Press to set target values for TIME, DISTANCE,
CALORIES, and PULSE.

This button will reset each function to zero.
To reset all functions to zero, press the button
and hold it down for three seconds.

Lower

Display

PRESET VALUES OPERATION:

Stop pedaling for four seconds. Press the MODE button to select functions for preset target values. The meter will
cycle through the functions as follows and allow you to set the function values.

Time (0:00 to 99:00) Distance (0.0 to 99.5 mile) Calories (0 to 9999 cal) Pulse (30 to 240 BPM)

Use SET & RESET buttons to enter desired values a nd press MODE button to confirm and move to next function for
presetting. To pass the setting of some functions, just press the MODE button. Start to run the Meter functions by
pedaling.

FUNCTIONS:

SCAN:

SPEED:

TIME:

DISTANCE:

CALORIES:

PULSE:

TEMPERATURE: Displays the current environment temperature.

Upper display automatically scans SPEED, TIME, DISTANCE, CALORIES, PULSE, and
TEMPERATURE in sequence with a change every four seconds. Pre ss and rele ase the MODE button

until "SCAN" appears on display.
Displays the current speed from zero to 999 miles per hour.
Counts upward to 99:59 in one second increments. Counts down from preset value.
Displays distance up to 99.99 miles in increments of 0.01 miles. Counts down from preset value.
Displays the calorie consumption from zero to 9999 Kcal. Counts down from preset value.
The calories readout is an estimate for an average user. It should be used only as a comparison
between workouts on this unit.
Displays your pulse rate in beats per minute. T o display pulse, gra sp the Pulse Sen sors on the Stationary

Handlebar, one in each hand. The heart symbol " " will begin flashing when the Electronic Meter
senses your pulse. Your pulse will be displayed approximately five (5) seconds after the heart icon is
displayed. If you do not place your hands correctly and 60 seconds passes without a pulse input, the
Meter will turn off the pulse circuit. Press the MODE button to restart and pla ce your hands ba ck on the
Pulse Sensors correctly. The pulse readout will appear again.
If you preset the PULSE value, the Meter will warn you with an audible alarm when your pulse exceeds
the set value. Stop exercising until your pulse comes down.

HOW TO INSTALL AND REPLACE BATTERIES:

Open the Battery Door on the back of the meter.

1.
The meter operates with two AA batteries. Two batterie s included. Refer

2.
to the illustration to install or replace the batteries.

AA Batteries

NOTE:

Do not mix a new battery with an old battery.

1.
Use the same type of battery. Do not mix an al kaline battery with a nother

2.
type of battery.
Rechargeable batteries are not recommended.

3.

14

STORAGE

1.

To store the Magnetic 1772 Elliptical, simply keep it in a clean dry place.

2.

The minimum rest dimensions of the Magnetic 1772 Elliptical are approximately 47 5/8 inches long x
60 1/4 inches tall x 24 3/8 inches wide. These dimensions may vary. Please measure your Magnetic
1772 Elliptical if exa ct dimensions are needed.

3.

Move the Magnetic 1772 Elliptical with the moving wheels on the FRONT STABILIZER(2). Grasp the
ST A TIONARY HANDLEBAR(7) on the UPRIGHT(6), tip the Magnetic 1772 Elli ptical forward a nd move
slowly.

4.

To avoid damage to the METER(26), remove the batteries before storing the Magnetic 1772 Elliptical
for one year or more.

MAINTENANCE

The safety and integrity designed into the Magnetic 1772 Elliptical can only be maintained when the
Magnetic 1772 Elliptical is regularly examined for damage and wear . Special attention should be given to

the following:

Adjust the TENSION KNOB(25) and verify that the Magnetic System provides tension. The Magnetic

1.

System should provide many years of use.
Verify that the W A RNING LABEL(91) is in pla ce a nd easy to read. Call Sta mina Products immedi ately at

2.

1-800-375-7520 for a replacement W A RNING LABEL(91) if it is missing or damaged.
It is the sole responsibility of the user/owner to ensure that regular maintenance is performed.

3.

Worn or da maged components shall be re placed immediately or the Magnetic 1772 Elliptical removed

4.

from service until repair is made.
Only Sta mina Products supplied components shall be used to maintain/repair the Magnetic 1772 Elliptical.

5.

Keep your Magnetic 1772 Elliptical clean by wiping with an absorbent cloth after use.

6.

15

CONDITIONING GUIDELINES

How you begin your exercise program depends on your physical condition. If you have been inactive for

several years or are severely overweight, start slowly and increase your workout time gradually. Increase
your workout intensity gradually by monitoring your heart rate while you exercise.

Remember to follow these essentials:

Have your doctor review your training and diet programs.
Begin your training progra m slowly with realistic goals that have been set by you and your physician.
Warm up before you exercise and cool down after you work out.
Take your pulse periodically during your workout and strive to stay within a range of 60% (lower
intensity) to 90% (higher intensity) of your maximum heart rate zone. Start at the lower inten sity, and
build up to higher intensity as you become more aerobically fit.
If you feel dizzy or lightheaded you should slow down or stop exercising.

Initially you may only be able to exercise within your target zone for a few minutes; however, your a erobic
ca pa city will i mprove over the next six to eight week s. It is i mporta nt to pa ce yoursel f while you exercise so
you don't tire too quickly.

To determine if you are working out at the correct intensity, use a he art rate monitor or use the table below .
For effective aerobic exercise, your heart rate should be maintained at a level between 60% and 90% of
your maximum heart rate. If just starting an exercise progra m, work out at the low end of your target he art
rate zone. As your a erobic ca pa city improves, gra dually increa se the intensity of your workout by increa sing
your heart rate.

Measure your heart rate periodically during your workout by stopping the
exercise but continuing to move your legs or walk around. Place two or three
fingers on your wrist a nd take a six second heartbe at count. Multiply the results
by ten to find your heart rate. For exa mple, if your six se cond heartbeat count
is 14, your heart rate is 140 beats per minute. A six second count is used
because your heart rate will drop ra pidly when you stop exercising. Adjust the
intensity of your exercise until your heart rate is at the proper level.

Target Heart Rate Zone Estimated by Age*

Age

20 years
25 years
30 years
35 years
40 years
45 years
50 years
55 years
60 years
65 years
70 years

Target Heart Rate Zone

(55%-90% of Maximum Heart Rate)

110-180 beats per minute
107-175 beats per minute
105-171 beats per minute
102-166 beats per minute

99-162 beats per minute
97-157 beats per minute
94-153 beats per minute
91-148 beats per minute
88-144 beats per minute
85-139 beats per minute
83-135 beats per minute

Average Maximum

Heart Rate 100%
200 beats per minute
195 beats per minute
190 beats per minute
185 beats per minute
180 beats per minute
175 beats per minute
170 beats per minute
165 beats per minute
160 beats per minute
155 beats per minute
150 beats per minute

wrist pulse

For cardiorespiratory training benefits, the American College of Sports Medicine re commends working

*

out within a heart rate range of 55% to 90% of maximum heart rate. To predict the maximum heart
rate, the following formula was used: 220 - Age = predicted maximum heart rate

16

WARM-UP and COOL-DOWN

Warm-Up The purpose of warming up is to prepare your body f or exercise and to mini mize injuries. W arm

up for two to five minutes before strength training or aerobic exercising. Perform activities that raise your
heart rate a nd warm the working muscles. Activities may include brisk walking, jogging, jumping ja ck s, jump
rope, and running in place

Stretching Stretching while your muscles are warm after a proper warm-up and again after your strength

or aerobic training session is very important. Muscles stretch more easily at these times because of their
elevated temperature, which greatly reduces the ris k of injury . Stretches should be held for 15 to 30 seconds.
Do not bounce.

Suggested Stretching Exercises

Lower Body Stretch

Place feet shoulder-width
apart and lean forward.
Keep this position for 30
seconds using the body as a
natural weight to stretch the
backs of the legs.
DO NOT BOUNCE!
When the pull on the back of
the legs lessens, gradually
try a lower position.

Bent Torso Pulls

While sitting on the floor,
have legs apart, one leg
straight and one knee bent.
Pull the chest down to touch
the thigh on the leg that is
bent, and twist at the waist.
Hold this position at least 10
seconds. Repeat 10 times
on each side.

Floor Stretch

While sitting on the floor,
open the legs as wide as
possible. Stretch the upper
body toward the knee on the
right leg by using your arms
to pull your chest to your
thighs. Hold this stretch 10
to 30 seconds.
DO NOT BOUNCE!
Do this stretch 10 times.
Repeat the stretch with the
left leg.

Bent Over Leg Stretch

Stand with feet shoulder­width apart and lean forward
as illustrated. Using the
arms, gently pull the upper
body towards the right leg.
Let the head hang down.
DO NOT BOUNCE!
Hold the position a minimum
of 10 seconds. Repeat
pulling the upper body to the
left leg. Do this stretch
several times slowly.

Remember to always check with your physician before starting any exercise program.

Cool-Down The purpose of cooling down is to return the body to its normal, or near normal, resting state

at the end of each exercise session. A proper cool-down slowly lowers your heart rate and allows blood to
return to the heart. Your cool-down should include the stretches listed above and should be completed after
each strength training session.

17

PRODUCT PARTS DRAWING

FRONT

Strap

BACK

18

PARTS LIST

PART# PART NAME QTY

1 Main Frame 1
2 Front Stabilizer 1
3 Rear Stabilizer 1
4 Left Pedal Arm 1
5 Right Pedal Arm 1
6 Upright 1
7 Stationary Handlebar 1
8 Left Handlebar 1
9 Right Handlebar 1
10 Lower Pivoting Arm 2
11 Linkage 2
12 Pulley and Axle 1
13 Bearing (6003Z) 2
14 Bearing Washer (M17) 1
15 C Ring (17mm) 2
16 V-Ribbed Belt 1
17 Idler Arm 1
18 Idler Wheel 1
19 Idler Wheel Spacer (
20 Tension Spring 1
21 Magnetic Resistance Unit 1
22 Eyebolt 2
23 Tension Bracket 2
24 Tension Cable 1
25 Tension Knob 1
26 Meter 1
27 Pulse Sensor Wire 1
28 Pulse Sensor Plate 2
29 Connection Wire 1
30 Sensor Wire 1
31 Magnet 1
32 Left Cover 1
33 Right Cover 1
34 Cover Cap 2
35 Left Crank 1
36 Right Crank 1
37 Left Flange Nut (M10 x 1.25, Left Hand Threads) 1
38 Right Flange Nut (M10 x 1.25, Right Hand Threads) 1
39 Lock Washer (M10) 2
40 Crank Cap 2
41 Left Pedal Shaft (9/16" - 20, Left Hand Threads) 1
42 Right Pedal Shaft (9/16" - 20, Right Hand Threads) 1
43 Bushing 8
44 Wave Wa sher (ø16.5 x ø23 x 0.4mm thick) 2
45 Large Washer (M8 x ø32 x 2mm thick) 4
46 Left Pedal Cap 1
47 Right Pedal Cap 1
48 Round Plug (38mm) 2

ø10 x ø16 x 16mm) 1

19

PARTS LIST

PART# PART NAME QTY

49 Plastic Washer (M8 x ø18 x 2mm thick) 8
50 Round Plug (28.6mm) 4
51 Spacer 2
52 Large Washer (M16 x ø32 x 0.5mm thick) 3
53 Dome Plug (28.6mm) 2
54 Foa m Grip 2
55 Short Foam Grip 2
56 Round Plug (25.4mm) 2
57 Round Plug (24.8mm) 2
58 Roller 2
59 Roller Spacer 4
60 Wheel 2
61 Leveling Cap 2
62 Cap Bushing 4
63 Securing Cap 4
64 Carriage Bolt (M8 x 1.25 x 75mm) 2
65 Bolt, Button Head (M8 x 1.25 x 15mm) 9
66 Bolt, Button Head (M8 x 1.25 x 20mm) 4
67 Bolt, Button Head (M8 x 1.25 x 48mm) 4
68 Bolt, Button Head (M8 x 1.25 x 75mm) 2
69 Bolt, Button Head (M10 x 1.5 x 50mm) 2
70 Bolt, Flat Head (M10 x 1.5 x 20mm) 1
71 Bolt, Flat Head (M10 x 1.5 x 38mm) 1
72 Bolt, Hex Head (M6 x 1 x 35mm) 4
73 Screw, Round Head (M4 x 12mm) 4
74 Screw, Round Head (M4 x 15mm) 2
75 Screw , Round He ad (M5 x 15mm) 11
76 Screw, Small Round Head (M5 x 25mm) 4
77 Screw , Round Head (M5 x 0.8 x 60mm) 1
78 Thin Nut (3/8" - 26 x 0.16" thick) 2
79 Nut (3/8" - 26 x 0.28" thick) 2
80 Nut (M6 x 1) 2
81 Nylock Nut (M8 x 1.25) 4
82 Nylock Nut (M10 x 1.5 x 10mm thick) 2
83 Nylock Nut (M10 x 1.5 x 7mm thick) 2
84 Acorn Nut (M6 x 1) 4
85 Acorn Nut (M8 x 1.25) 2
86 Arc Washer (M6) 4
87 Arc Washer (M8) 13
88 Lock Washer (M6) 4
89 Lock Washer (M8) 17
90 Foa m Pad 2
91 Warning Label 1
92 Allen Wrench (6mm) 1
93 Multi-Opening Wrench 1
94 Manual 1

20

LIMITED WARRANTY

MODEL 55-1772

WARRANTY

Stamina Products, Inc. warrants that this product will be free from defects in materials and workmanship
under normal use, service and proper operation f or a period of 90 days on the parts a nd three ye ars on the
frame from the date of the original purchase from an authorized retailer. THIS WARRANTY SHALL NOT

APPLY TO ANY PRODUCT WHICH HAS BEEN SUBJECT TO COMMERCIAL USE, ABUSE, MISUSE,
ALTERATION OF ANY TYPE OR CAUSE OR TO ANY DEFECT OR DAMAGE CAUSED BY REPAIR,
REPLACEMENT , SUBSTITUTION OR USE WITH PARTS OTHER THAN P ARTS PROVIDED BY ST AMINA
PRODUCTS, INC. Commercial use includes use of the product in athletic clubs, health clubs, spas,

gymnasiums, exercise facilitie s, and other public or semipublic facilities whether or not the product's use is
in furtherance of a profit making enterprise, and all other use which is not for personal, family, or household
purposes.

T o i mplement this li mited warranty, send a written notice stating your name, date, a nd pla ce of purcha se a nd
a brief description of the defect along with your rece ipt to Sta mina Products, Inc. P .O. Box 1071, Springf ield

Missouri, USA, 65801-1071, or email us at [e-mail], or call us at
1-800-375-7520. If the defect is covered under this limited warranty, you will be requested to return the
product or part to us for free repair or replacement at our option. NO ACTION FOR BREACH OF THIS
LIMITED WARRANTY MAY BE COMMENCED MORE THAN ONE (1) YEAR AFTER THE DATE THE
ALLEGED BREACH WAS OR SHOULD HAVE BEEN DISCOVERED. NO ACTION FOR BREACH OF
ANY IMPLIED W ARRANTY MAY BE COMMENCED MORE THAN ONE (1) YEAR AFTER DELIVERY OF
THE PRODUCT TO THE PURCHASER. This limited warranty is not transferable. IF ANY PART OF THE
PRODUCT IS NOT IN COMPLIANCE WITH THIS LIMITED W ARRANTY OR ANY IMPLIED W ARRANTY,
THE REMEDY OF REP AIR OR REPLACEMENT IS THE EXCLUSIVE REMEDY A V AILABLE T O YOU. In

the event that the purcha ser makes a ny claim under this limited warra nty or any i mplied warranty , the W arrantor
reserves the right to require the product to be returned for inspection, at the purchaser's expense, to the
Warra ntor's premises in Springfield, Missouri. Return of the enclosed warra nty registration card is not required
for warranty coverage, but is merely a way of establishing the date and place of purchase.

Sta mina Products, Inc. SHALL NOT BE LIABLE FOR THE LOSS OF USE OF ANY PRODUCT, LOSS OF

TIME, INCONVENIENCE, COMMERCIAL LOSS OR ANY OTHER INDIRECT, CONSEQUENTIAL,
SPECIAL OR INCIDENT AL DAMAGES DUE TO BREACH OF THE ABOVE WARRANTY OR ANY IMPLIED
WARRANTY.

This limited warra nty is the only written or expre ss warranty given by Stamina Products, Inc. This warranty
gives you specific legal rights, and you may also have other legal rights which vary from state to state.

ANY OTHER RIGHT WHICH YOU MAY HAVE, INCLUDING ANY IMPLIED WARRANTY OR
MERCHANT ABILITY OR FIT NESS FOR A P ARTICULAR PURPOSE, IS LIMITED IN DURA TION TO THE
DURA TION OF THIS WARRANTY.

The laws in some jurisdictions restrict the rights of manufacturers and distributors of consumer goods to
disclaim or limit implied warranties and consequential and incidental damages with respect thereto. If any
such law is found to be a pplicable, the foregoing disclai mers a nd limitations of a nd on implied warrantie s and
consequential a nd incidental da mages with respect thereto shall be disregarded a nd shall be deemed not to
have been made to the extent necessary to comply with such legal re striction.

21

NOTES

22

FAX/MAIL ORDERING FORM

Please do not return the product. For your convenience, Stamina's Customer Service Department can be
reached by email at [e-mail] or toll free at 1-800-375-7520 (in the U.S.).
Should a part be missing or a defective part found, please call us from 7:30 A.M. to 5:00 P.M. Central Ti me,
Monday through Thursday a nd 8:00 A.M. to 3:00 P.M. on Friday or fill out the fax sheet ordering form below
and fax it to [phone]. Our Customer Service Department will be able to assist you with your problem
and the part will be mailed directly to your house.

TELEPHONE

CUSTOMER SERVICE

Tel: [phone]

FAX

CUSTOMER SERVICE

Fax: [phone]

ONLINE

CUSTOMER SERVICE

[e-mail]

www.staminaproducts.com

STAMINA PRODUCTS, INC.

ATTN: Customer Service

Springfield, MO. 65801-1071

Detach and Mail or Fax the Form Below

Stamina Products, Inc.

P.O. Box 1071

Springfield, MO 65801-1071

Mr./Ms:
Address: Apt. #:
City: State: Zip Code:

IMPORTANT : We must have your phone number in order to process the order!

Phone #: ( ) Work Phone #: ( )
Date Purchased:
Model #:
Purchased From:

IMPORTANT : Before filling out the form below make sure you have the right information.

Refer to the parts list to make sure you're ordering the right parts!

MAIL

P.O. Box 1071

P ART # DESCRIPTION QUANTITY

EXAMPLE:

1 Rear Unit Assembly 1